Page 1
IMPORTANT
Carefully remove all the parts from the carton and
place them individually on a soft cloth to prevent
scratches or other damage.
Carefully and strictly follow these assembly instructions
to ensure a completed product as designed.
Do not use power tools above 8 volts to assemble.
Part List
A.
Side Panel
1 pc.
K.
Front Upright
2 pcs.
O.
Wine Grid
2 pcs.
B.
Side Panel
1 pc.
C.
Middle Panel
1 pc.
L.
Fixed Shelf
1 pc.
P.
Wine Grid
2 pcs.
Q.
Shelf
2 pcs.
D.
Middle Panel
1 pc.
M.
Base
1 pc.
R.
Door
1 pc.
E.
Back Panel
3 pcs.
F.
Back Upright
2 pcs.
G.
Back Stretcher
1 pc.
H.
Back Stretcher
1 pc.
I.
Front Stretcher
1 pc.
J.
Front Stretcher
1 pc.
T.
Drawer
3 pcs.
S.
Door
1 pc.
Refer to later page(s) of these
instructions for drawer assembly.
N.
Leg
2 pcs.
Hardware List
Hex Wrench
1 pc.
Small Hex Wrench
1 pc.
M6x35
Head Cap Bolt
4 pcs. (+1 extra)
M6x50
Head Cap Bolt (long)
8 pcs. (+1 extra)
Cam Lock
14 pcs. (+2 extra)
Cross Dowel
8 pcs. (+1 extra)
Cam Lock Screw
14 pcs. (+1 extra)
M3.5x25
Wood Screw (long)
24 pcs. (+1 extra)
M3.5x13
Wood Screw (short)
12 pcs. (+1 extra)
Adjustable Pin
8 pcs. (+2 extra)
M4x25
Machine Screw
8 pcs.
M3.5x16
Wood Screw
for Back Panel
12 pcs. (+1 extra)
20 05100 Top carton is also needed for assembly.
Tool(s) required for assembly: Phillips screwdriver, Level, Drill (8 volts or less), 3/8” Drill Bit
Knob
2 pcs.
Handle
3 pcs.
Page 2
Assembly Instructions 2/8
IMPORTANT
Use a soft cloth between these parts and the floor.
Do not use power tools above 8 volts to assemble.
Do not tighten all the bolts until each part is properly assembled.
The unit must be level to work properly. Use the included adjustable levelers to level.
Keep Hex Wrench as the bolts may need to be tightened in the future.
STEP 1
Insert Cam Lock Screws into pre-drilled holes
in Side Panels (A), (B) and Middle Panels (C), (D),
then tighten. (See Figure 1)
A
Cam Lock Screw
D
B
C
D
L
Figure 1
Figure 2
C
Cam Lock
STEP 2
Attach Middle Panels (C) and (D)
to Fixed Shelf (L) with Cam Locks.
(See Figure 2)
Page 3
E
E
Assembly Instructions 3/8
STEP 3
Attach Back Stretcher (H) to unit with Cross Dowels
and Head Cap Bolts (long). (See Figure 3)
Attach Back Uprights (F) to Back Stretcher (H).
Figure 3
F
H
E
F
Cross Dowel
Head Cap Bolt (long)
STEP 4
Attach Back Stretcher (G) to
unit with Cross Dowels
and Head Cap Bolts (long).
Slide Back Panels (E) into position.
Head Cap Bolt (long)
Cross Dowel
G
K
I
K
J
STEP 5
Attach Front Stretcher (J) to unit.
Attach Front Uprights (K) to unit.
Attach Front Stretcher (I) to unit.
Page 4
STEP 6
Attach Side Panels (A) and (B) to
unit with Cam Locks.
Cam Lock
Assembly Instructions 4/8
Cam Lock
B
A
Cross Dowel
N
N
Head Cap Bolt
Head Cap Bolt (long)
M
STEP 7
Attach Base (M) to unit with Cross Dowels
and Head Cap Bolts (long).
Attach Legs (N) to Base (M)
with Head Cap Bolts.
Cam Lock Screw
U
STEP 8
Place Top (U) upside down on a soft cloth.
Insert Cam Lock Screws into pre-drilled holes in Top (U), then tighten.
Arrow label
Page 5
Assembly Instructions 5/8
STEP 9
Turn unit to its’ upright position.
Insert Adjustable Pins into
side panels and middle panels
at desired level.
Place Shelves (Q) into position.
Attach Doors (R) and (S) to unit by
sliding door hinges into side panel
hinges. (See Figure 4)
Attach Knobs to Doors (R) and (S)
with Machine Screws. (See Figure 5)
Knob
Machine Screw
R
Q
Q
S
Adjustable Pin
U
Figure 4 Figure 5
Cam Lock
STEP 10
Attach Top (U) to unit with Cam Locks.
Note: Arrow label indicates front of Top (U).
Page 6
Drawer (T)
Assembly Instructions 6/8
Wood Screw (long)
Bottom
T1
T3
T2
Roller at back
STEP 12
Slide Drawer Bottom (T5) into groove.
Attach Drawer Bottom (T5) to unit
with Wood Screws (short).
STEP 11
Attach Drawer Front (T1) and Drawer
Back (T2) to Drawer Side (T3) with
Wood Screws (long).
T4
Attach Drawer Side (T4) to unit with
Wood Screws (long).
Wood Screw (short)
T5
Part List
T1.
Drawer Front
3 pcs.
Handle
T2.
Drawer Back
3 pcs.
Machine Screw
T3.
Drawer Side
3 pcs.
STEP 13
Attach Handle with Machine Screws.
T4.
Drawer Side
3 pcs.
T5.
Drawer Bottom
3 pcs.
Page 7
T
T
Assembly Instructions 7/8
STEP 14
Slide Drawers (T) into position.
STEP 15
P
O
O
L
P
T
Slide Wine Grids (P) into
grooves of Fixed Shelf (L).
Slide Wine Grids (O) into unit.
Wood Screw for Back Panel
Level unit by adjusting the adjustable
levelers on bottom of unit.
(See Figure 6)
Insert Wood Screws for Back Panel
into pre-drilled holes in unit,
then tighten.
Note: Unit must be level before
tightening these screws.
Figure 6
Page 8
Assembly Instructions 8/8
IMPORTANT
To help reduce the risk of the unit tipping over, the Tip-over Restraint must be installed following these instructions exactly.
STEP 16
Place unit at desired location.
3/8” wall hole
Drill a 3/8” hole in wall in-line with
Pre-drilled hole at top of unit.
Move unit.
Insert Anchor into the wall hole
and attach Bracket with Wall Screw.
Attach Bracket at pre-drilled hole
at top of unit with Wood Screw.
Move unit back into place.
Slide Tip-over Restraint through
Bracket on wall and Bracket on unit.
(See Figure 7)
Put tie end of Tip-over Restraint into lock
end of Tip-over Restraint and pull until tight.
Anchor in wall
Tie end
Lock end
Bracket at
top of unit
Tip-over
Restraint
Bracket
on wall
Wall Screw
Figure 7
Pre-drilled hole
at top of unit
Wood Screw
Hardware List
Anchor
1 pc. (+1 extra)
Bracket
2 pcs. (+1 extra)
Tip-over Restraint
1 pc. (+1 extra)
Drill 3/8” hole in wall
M3.5x40
Wall Screw
1 pc. (+1 extra)
Top of unit
M3.5x16
Wood Screw
1 pc. (+1 extra)
Page 9
CARE INSTRUCTIONS
NEVER
allow liquids to remain on furniture.
Absorption causes parts to warp
and split and finishes to delaminate.
Do not use power tools
above 8 volts to assemble.
PREVENT
CRACKING
Do not place
in direct sunlight.
PREVENT
FADING
NEVER
use glass cleaners on
finished furniture. Ammonia
chemically attacks the finish.
Do not write
directly on surface.
PREVENT
MARKING
Do not place hot
objects on surface.
PREVENT
FINISH DAMAGE
Do not use rubber
based placemats.
PREVENT
DISCOLORING
Do not use commercial
waxes and polishes.
PREVENT
YELLOWING
CLEAN
with a soft cloth moistened
in lukewarm soap and water.
Buff with a dry clean cloth.
We will provide replacements free of charge for missing or damaged hardware or parts within 30 days of purchase.
Digital images of the defective parts may be required. If the product was not purchased from an authorized retail
affiliate, We are under no obligation to provide replacement parts. Parts are not available for fully assembled items nor
are parts available for sale. Replacements for missing or damaged hardware or parts may be requested at our website.
Loading...