Page 1
Top Assembly Instructions
Granite Top
PART LIST HARDWARE LIST
W3.
Top
1 pc.
X.
Top Support
2 pcs.
Head Cap Bolt
6 pcs. (+1 extra)
Page 2
STEP 1
Put Top Support (X) into the
pre-drilled holes, using Head
Cap Bolts to attach it to the unit.
W3
Top Assembly Instructions
X
X
Head Cap Bolt
STEP 2
Place Top (W3) onto the unit,
then tighten up all
Head Cap Bolts.
STEP 3
Attach Pull Handles to
Door (S) and (T), using Machine
Screws. (See figure 1)
Attach Door (S) and (T) to
Side Panel (A) and (B), slide the
door lift hinges into the side panel
lift hinges. (See figure 2)
Head Cap Bolt
S
A
Figure 1
V
U
U
U
T
Figure 2
B
Slide Drawers (U) and (V)
into place.
Page 3
Top Assembly Instructions
Granite Top
Page 4
Steel Plate Connector
Top Assembly Instructions
Head Cap Bolt
(short)
STEP 1
Remove Drawers from the unit.
W3
Steel Plate
Connector
Flat Washer
Spring Washer
Head Cap Bolt
(short)
(Figure 1)
Place the selected ‘Top’ on the unit, attach it to the body with the Steel Plate Connectors,
Flat Washers, Spring Washers and Head Cap Bolts. (See figure 1)
Slide the Drawers into place.
Page 5
Kitchen Cart
IMPORTANT NOTE
Carefully remove all the parts from the carton and put
them individually on a soft cloth to prevent scratches
or other damages occuring to the parts.
We have taken great care in the design of this
product and request that you carefully and strictly
follow our assembly instructions to ensure a
completed product as it was designed.
PART LIST
H.
Back Stretcher
1 pc.
J.
Base
1 pc.
P.
Adj. Shelf
2 pcs.
B.
Side Panel
1 pc.
Q.
Adj. Shelf
1 pc.
Stretcher
K.
Door
Front
1 pc.
.2 pcs
C.
Middle Panel
2 pcs.
I.
Side Rack
1 pc.
L.
Door
2 pcs.
R.
M.
Drawer
Divider
1 pc.
D.
Side Panel
1 pc.
E.
Back Panel
2 pcs.
F.
Back Panel
1 pc.
N.
KD. Drawer
2 pcs.
(For Drawer N, packed in separate carton
with hardware and assembly instructions.)
S.
Side Rack
1 pc.
T.
Base Rack
1 pc.
G.
Back Piece
2 pcs.
HARDWARE LIST
Caster
two lock
two non-lock
4 pcs.
Hex Wrench
1 pc.
Small
Hex Wrench
1 pc.
Head Cap Bolt (short)
for Side Towel Bar
2 pcs. (+1 extra)
Tools required for assembly : Phillips screwdriver
Wood Screw
for Caster
16 pcs. (+2 extra)
Adjustable Pin
12 pcs. (+2extra)
Head Cap Bolt
11 pcs. (+1extra)
Head Cap Bolt
(short) for Top
4 pcs. (+1 extra)
Wood Plug
8 pcs.
(+2 extra)
Steel Plate
Connector
for Top
4 pcs.
U.
Brush Chrome Pipes
3 pcs.
4 pcs. (+1 extra)
Spring
Washer
for Top
4 pcs. (+1 extra)
Towel Bar
1 pc.
Flat
Washer
for Top
Machine Screw
for Pull Handle
8 pcs.
O.
Pull Handle
4 pcs.
Page 6
IMPORTANT
Do not tighten up all the screws until each part is properly assembled.
You should keep Hex Wrench in the safe place as you may need to
tighten up the Head Cap Bolts in the future.
STEP 1
Attach four Casters to the Base (J) with
Wood Screws.
(See the ‘Arrow’ sticker indicating front area
on the base.)
STEP 2
Attach the Side Panel (D) to the Base (J).
Assembly Instructions 2/3
G
C
C
G
D
Tighten Head Cap Bolt only half way.
Attach the Back Piece (G) to the Base
and the Middle Panel (C) to the Back Piece (G).
Tighten Head
Cap Bolt by
Hex Wrench.
Head Cap Bolt
STEP 3
Slide the Back Panel (E) and (F) in places.
Attach the Back Stretcher (H) and Front
Stretcher (I) to the unit with Head Cap Bolts
through the Side Panel (D).
Tighten Head Cap Bolts half way.
Locking Casters
E
B
H
J
Head Cap Bolt
Head Cap Bolt
(short)
M
F
I
E
O
Attach the Drawer Divider (M) in between
the Back Stretcher (H) and Front Stretcher
(I), using Head Cap Bolt.
Attach the Side Panel (B) to the unit, using
Head Cap Bolts.
Tighten up all Head Cap Bolts.
Attach the Towel Bar (O) to the Side Panel (D), using Head Cap Bolts (short).
D
Head Cap Bolt
Page 7
Head Cap Bolt
Assembly Instructions 3/3
STEP 4
Attach the Side Rack (R) to the Side Panel (B)
with the Head Cap Bolt.
B
R
T
S
U
STEP 5
Install the Doors (K) and (L), using
Spring Pin Hinge.
(See figure 1)
Assemble the Door Pull Handles,
using the Machine Screws.
(See Figure 2)
Attach the Brush Chrome Pipes (U) to the pre-drilled
holes of Side Rack (R).
Attach the Base Rack (T) to the Side Rack (R).
Attach the Side Rack (S) to the Side Panel (B),
using Head Cap Bolt.
K
K
(Figure 1)
Adjustable Pin
P
(Figure 2)
N
Q
N
P
L
L
STEP 6
Put the Adjustable Pins into the side panels
at the desired level. Place Shelf (P),(Q).
Slide the Drawer (N) into places.
STEP 7
Cover up all holes with
Wood Plugs
*** See the process in assembling the top in separate sheet.
Page 8
N3
N2
N5
Drawer (N)
UNIT PART LIST
N4.
Side Part
2 pcs.
N1.
Front Part
2 pcs.
N2
Figure 2
Turn the assembled drawer over and slide the
Plywood Bottom Part (N5) into the grooves
on Side Parts (N3) and (N4). Be sure to push
the plywood all the way forward so it meets the
Front Part (N1).
N4
N2.
Back Part
2 pcs.
Figure 1
N3.
Side Part
2 pcs.
N1
N3
MAKE SURE ROLLER
IS ON THE BACK
N1
N4
HARDWARE LIST
N4
1
2
Wood Screw / ”
(for Bottom Part)
12 pcs.
Wood Screw 1”
(for Side Part)
16 pcs.
Instructions
N5.
Bottom
2 pcs.
Pull Handle
2 pcs.
Machine Screw
for Pull Handle
4 pcs.
Assembly
Figure 1
Line up Side Parts (N3) and (N4) to the Front Part
(N1) and Back Part (N2). Be sure to follow the
‘Arrow’ sign sticker on the parts.
Using a screw driver, insert 1” screwsPhillip’s
into each of the 4 pre-drilled holes on Side Parts
(N3) and (N4), then tighten half way.
N3
N1
Figure 2
N5
N3
N2
Figure 3
N5
N1
N4
Figure 3
Insert the remaining (6) 1/2” screws
into the pre-drilled holes on Bottom Part
(N5), then tighten all screws
Figure 4
Figure 4
Assemble the Pull Handle
with Machine Screw on
the Front Part (N1).
Page 9
PART LIST
HARDWARE LIST
W.
Top
1 pcs.
Attention !
This Top can be used for both kitchen cart
series.
Steel Plate Connector
Head Cap Bolt
(short)
A
X.
Top Support
2 pcs.
Top Assembly
Head Cap Bolt
6 pcs. (+1 extra)
Instructions
Steel Plate
Connector
Flat Washer
Spring Washer
Head Cap Bolt
(short)
STEP 1
Now, you’ll be able to create your own kitchen cart.
Make your own choice of the ‘Top’, wood or
stainless steel or granite.
Remove Drawers from the unit.
Place the selected ‘Top’ on the unit,
attach it to the body with
the Steel Plate Connectors,
Flat Washers, Spring Washers and
Head Cap Bolts. (See figure 1)
Slide the Drawers into place.
(Figure 1)
Loading...