Page 1
Kitchen Cart
He
p
se
IMPORTANT NOTE
Carefully remove all the parts from the carton and put
them individually on a soft cloth to prevent scratches
or other damages occurring to the wood parts.
We have taken great care in the design of this
product and request that you carefully and strictly
follow our assembly instructions to ensure a
completed product as it was designed.
Part List
G.
Back Stretcher
1 pc.
H.
Front Stretcher
1 pc.
A.
Side Panel
1 pc.
J.
Base
1 pc.
pc.
N.
Door
1 pc.
B.
Side Panel
1 pc.
O.
Door
1 pc.
Hardware List
Hex Wrench
1 pc.
C.
Middle Panel
1 pc.
P.
Side Rack
1 pc.
R.
Base Rack
1 pc.
M6x35
Head Cap Bolt (long)
14 pcs. (+1 extra)
D.
Middle Panel
1 pc.
K.
Shelf
2 pcs.
Q.
Side Rack
1 pc.
E.
Back Panel
3 pcs.
S.
Pipe
3 pcs.
M4x16
Wood Screw
for Caster
16 pcs. (+1 extra)
F.
Back Piece
2 pcs.
L.
Handle Arm
2 pcs.
T.
Drawer
3 pcs.
(Please refer to the last pages of these
instructions for drawer assembly.)
Wood Plug
10 pcs. (+2 extra)
Knob
2 pcs.
I.
Front Rail
3 pcs.
M.
Round Arm
1 pc.
U.
awer
Drawer
1 pc.
M4x25
Machine Screw
10 pcs.
Caster
Two with lock and
Two non-locking
4 pcs.
Small
Hex Wrench
1 pc.
M3.5x25
Wood Screw (long)
32 pcs. (+1 extra)
M3.5x13
Wood Screw (short)
24 pcs. (+1 extra)
Tools required for assembly : Phillips screwdriver
Adjustable Pin
8 pcs. (+1 extra)
Pull Handle
4 pcs.
Page 2
Assembly Instruction 2 / 6
IMPORTANT
* Do not tighten up all the screws and bolts until each part is properly assembled.
* You should keep Hex Wrench in a safe place as you may need to tighten up the Head Cap Bolts in the future.
* Use a soft cloth between these parts and the fl
STEP 1
Attach 4X Casters to Base (J) with Wood Screws for Caster, with the
Locking Casters at the front as indicated by ‘Arrow’ sticker. (see Figure 1)
oor.
Figure 1
C
F
Non-Locking Casters
Locking Casters
Wood Screw for Casters
J
I
F
STEP 2
I
D
Attach Back Pieces (F) to Middle Panels (C)
and (D).
I
Attach Front Rails (I) to Middle Panels (C)
and (D).
Page 3
A
Assembly Instruction 3 / 6
STEP 3
ST
Attach unit to Base (J).
Atta
Attach Side Panel (A) to unit with Head Cap Bolts.
Atta
(see Figure 2)
see
J
Head Cap Bolt
STEP 4
Slide Back Panels (E) into the unit.
Attach Back Stretcher (G) and Front
Piece (H) to the unit with Head Cap
Bolts.
Attach Side Panel (B) with Head Cap
Bolts.
G
E
H
Figure 2
Head Cap Bolt
E
E
B
Head Cap Bolt
Q
R
S
S
S
STEP 5
Attach Side Rack (Q) to the unit with Head Cap
Bolts.
P
Slide Base Rack (R) and Pipes (S) to Side Rack
(Q).
Attach Side Rack (P) to unit with Head Cap Bolts.
Page 4
STEP 6
Assembly Instruction 4 / 6
Head Cap Bolt
Assemble Handle Arms (L) to Side
Panel (B) with Head Cap Bolts.
Slide Round Arm (M) into place.
L
L
M
B
STEP 7
Insert Adjustable Pins into
side panels and middle panels
at the desired level and slide
Shelves (K ) into place.
K
Adjustable Pin
STEP 8
Cover all holes with Wood Plugs.
(see Figure 3)
K
Wood Plug
Figure 3
Wood Plug
Page 5
Drawer (T)
4
Assembly Instruction 5 / 6
T3
T2
Figure 1
MAKE SURE ROLLER
IS ON THE BACK
STEP 1
Attach T1 to T3 and T4, using
a Phillips screwdriver and
long wood screws (4X), tighten
halfway.
Attach T2 to T3 and T4 using
long wood screws (4X), tighten
halfway. (see Figure 1)
Figure 3
T3
T1
T1
T4
Figure 2
T3
T1
T5
T2
STEP 2
Slide T5 into the grooves in T3
and T4. Push T5 all the way
forward so it meets T1. (see
Figure 2)
T4
T5
T2
STEP 3
Insert short wood screws (6X)
into the pre-drilled holes in T5
and tighten. (see Figure 3)
Part List
T1.
Front Part
3 pcs.
T2.
Back Part
3 pcs.
T4
Figure 4
Figure
STEP 4
Assemble Pull Handle
with Machine Screws.
(see Figure 4)
Tighten all screws used in drawer assembly.
T3.
Side Part
3 pcs.
T4.
Side Part
3 pcs.
T5.
Base Part
3 pcs.
Page 6
Drawer (U)
.
4
U3
Assembly Instruction 6 / 6
U1
U2
Figure 1
STEP 1
Attach U1 to U3 and U4, using
a Phillips screwdriver and
long wood screws (4X), tighten
halfway.
Attach U2 to U3 and U4 using
long wood screws (4X), tighten
halfway. (see Figure 1)
Figure 3
U3
U5
MAKE SURE ROLLER
IS ON THE BACK
U1
U4
Figure 2
U3
U1
U5
U4
U2
STEP 2
Slide U5 into the grooves in U3
and U4. Push U5 all the way
forward so it meets U1. (see Figure 2)
Figure
Figure 4
U2
U4
STEP 4
STEP 3
Insert short wood screws (6X)
into the pre-drilled holes in U5
and tighten. (see Figure 3)
Assemble Pull Handle
with Machine Screws.
(see Figure 4)
Tighten all screws used in drawer assembly.
Part List
U1.
Front Part
1 pc.
U2.
Back Part
1 pc.
U3.
Side Part
1 pc.
U4.
Side Part
1 pc.
U5.
Base Part
1 pc.
Loading...