Page 1
Caution : You should read this carefully before proceeding
Please look in the velcro pouch for hardware packs and legs
Page 1 OF 10
LIFT TOP WRITING DESK
Picture
Label Picture Description QTY
Desk Top
A
B Left Front Leg 1
1
Page 2
C Right Front Leg 1
Long Bolt
(
)
Spring Washer
(
1/4")
Flat Washer
(
1/4"x16mm)
Screw
(
M8x38mm)
Page 2 OF 10
D Hind Leg 2
E Connecting Rod 2
F Connecting Rod 1
Label Picture Description QTY
ķ
9
000
ʓ
9
ѫ
ʔ
9
ѫ
ʕ Allen Key 1
ʖ
7
Page 3
ļ
Screwdriver
(not provided)
Power Drill
(not provided)
Wall Plug Screw
(M6X25mm)
screw
(
8x15mm)
ᬏ
Wall Plug
(10X30mm)
ᬐ
ᬑ
Hammer
(not provided)
Before
Beginning
Assembly:
Page 3 OF 10
1
Ľ
1
ʙ Bracket 4
Ŀ
ŀ
0
4
4
4
Restraint Strap 2
1
Page 4
This Desk has multiple parts and may require up to 30 minutes to
assemble. To give you an overview of the Desk parts, the above picture
is provided to help you put the various parts into perspective. Please
read through the instructions below to familiarise yourself with the parts
and steps before assembly.
Overview
Page 4 OF 10
Desk Top
Page 5
Step 1
Step 2
Please place the product on a platform.
Lift up on the top of the Writing Desk to open, then take out the inner
carton.
Attach the Desk Legs(C) to the Desk Top(A) using Bolts(), Spring
Washers(ཱ), Washers(ི) and the Allen Key(ཱི).
Do not fully tighten the Bolts at this time.
Page 5 OF 10
Page 6
Step 3
Place the Desk Top(A) facedown onto a clean, non-marring surface.
3.1 Connect the Rods (E)and(F) to the Table Front Legs (B)and(C)and
the Hind Legs(D) using screws (Ļ) and a Screwdriver(ļ)
3.2) Insert the Connecting Rods(E)and(F) to the Hind Legs(D) using
screws (Ļ) and a Screwdriver(ļ)
Tighten all Screws and Bolts at all joints in a sequential manner.
Step 4
Page 6 OF 10
Page 7
Usage For Console Restraint Device:
To secure Console against wall, attach two Brackets (ľ) on the wall
and the product, use Restraint Straps (⑫) to connect the Brackets (ľ).
Console Restraint Device Installation Instructions
Serious or fatal crushing injuries can occur from tipping furniture.
To help prevent tip-over: ALWAYS secure this furniture to the wall
using a Cabinet Restraint Device.
See product instructions for more ways to help prevent furniture
tip-over.
Page 7 OF 10
Page 8
Step 5
5.1)Drill two holes in the wall with a power drill Ľ.
You can mark these points in two ways as mentioned below:
1) Move the Desk back to the wall. Mark two points on the wall that are
at the same height as the desk .
Note: The Brackets need to be secured to a solid, load bearing surface.
Please use a Stud Finder(not supplied) if needed to locate the Wall
Frame.
2) Measure the height of the Brackets (ľ) with a ruler/measuring tape
and mark on the wall to keep them accurate and at the same height.
5.2) Insert Wall Plugs (ջ ) into the drilled holes on the wall with a
Hammer (ս).Attach Brackets (ľ) to Wall Plugs (ջ) using Wall Plug
Screws (Ŀ) with Screwdriver (ļ).
Step 6
Page 8 OF 10
Page 9
Step 7
The last step
Pull the Restraint Straps (ᬐ) through the Brackets (ľ) on the wall
and the desk one by one, and pull the Restraint Straps (ᬐ) tight.
This Writing Desk is now ready to use.
Caution: This Writing Desk can only be used on flat, level surface.
Use a Screwdriver (ļ) to lock the Bracket (ľ) with screws(ŀ)to the
back of the desk.
Note: Measure the height of the Brackets (ľ) with a ruler/measuring
tape and mark on wall to keep them accurate and at the same height.
Page 9 OF 10
Page 10
Page 10 OF 10
Loading...