Page 1
Kitchen Cart
IMPORTANT NOTE
Carefully remove all the parts from the carton and put
them individually on a soft cloth to prevent scratches
or other damages occurring to the wood parts.
We have taken great care in the design of this
product and request that you carefully and strictly
follow our assembly instructions to ensure a
completed product as it was designed.
PART LIST
A.
Top
1 pc.
E.
Back Panel
3 pcs.
K.
Arm
2 pcs.
F.
Back Upright
2 pcs.
M.
Side Rack
1 pc.
Side Panel
G.
Back Stretcher
1 pc.
H.
Back Stretcher
1 pc.
P.
Rack
1 pc.
B.
1 pc.
Q.
Door
1 pc.
I.
Front Piece
1 pc.
C.
Side Panel
1 pc.
J.
Base
1 pc.
R.
Door
1 pc.
D.
Middle Panel
1 pc.
L.
Towel Bar
1 pc.
N.
Side Rack
1 pc.
HARDWARE LIST
Caster
2 lock
2 non-lock
4 pcs.
Hex Wrench
1 pc.
Small Wrench
1 pc.
Magnet
2 pcs. (+1 extra)
M3x16
Wood Screw
for Magnet
4 pcs. (+1 extra)
O.
Base Rack
1 pc.
M4x32
Wood Screw
6 pcs. (+1 extra)
Flat Washer
6 pcs. (+1 extra)
Cam Lock Screw
22 pcs. (+2 extra)
Cam Lock
22 pcs. (+6 extra)
S.
Shelf
2 pcs.
M3.5x16
Wood Screw (short)
for Drawer Base Part
and Back Panel
24 pcs. (+1 extra)
M6x25
Head Cap Bolt
4 pcs. (+1 extra)
T.
Drawer
3 pcs.
(Please refer to the last page of these
instructions for drawer assembly steps.)
M3.5x25
Wood Screw (long)
for Drawer Side Part
24 pcs.(+1 extra)
M6x12
Head Cap Bolt
for Caster
16 pcs. (+1 extra)
Adjustable Pin
8 pcs. (+1 extra)
Drawer
Pull Handle
5 pcs.
M4x25
Machine Screw
5 pcs.
Page 2
Assembly Instructions 2/6
IMPORTANT
* Do not tighten up all the screws until each part is properly assembled.
* Use a soft cloth between these parts and the floor.
STEP 1
Attach 2X Magnets to Top (A) by
using Wood Screws (for Magnet)
into the pre-drilled holes.
(See Figure 1)
Insert Cam Lock Screws into
the pre-drilled holes of
Top (A), Side Panels
(B) and (C),
Middle Panel (D)
and Base (J).
(See Figure 2)
Wood Screw (for Magnet)
Magnet
B
J
B
D
C
Figure 1
C
Figure 2
A
Cam Lock Screw
Head Cap Bolt
Head Cap Bolt
N
P
K
O
K
Figure 3 Figure 4
STEP 2
Attach Arms (K) to Side Panel (B) with Head Cap Bolts. (See Figure 3)
Assemble Side Racks (M), (N), Base Rack (O) and Rack (P), then attach to Side Panel (C) with
Head Cap Bolts. (See Figure 4)
B
C
M
Page 3
Assembly
Cam Lock
Instructions 3/6
B
G
E
E
F
E
F
H
STEP 3
Attach Back Stretcher (H) to Side Panel (B) with Cam Lock.
(See Figure 5)
Attach Back Uprights (F) and slide Back Panels (E) into position.
Attach Back Stretcher (G) to unit with Cam Locks.
Attach Side Panel (C) to unit with Cam Locks.
C
Figure 5
Non-Locking Caster
Head Cap Bolt
J
STEP 4
Attach 4 Casters underneath Base (J) with Head Cap Bolts (for Caster),
put 2 Casters with Lock at the front side. (See Figure 6)
Locking Caster
Figure 6
(for Caster)
Page 4
STEP 5
Assembly
Instructions
4/6
Attach Middle Panel (D) and Front Pieces (I) to
unit from Step 3 with Cam Locks.
Attach base unit to
unit with Wood Screws
and Flat Washers.
Flat Washer
Wood Screw
I
I
D
G
L
Wood Screw
(short)
H
STEP 6
Turn the unit to its’
upright position.
Slide Towel Bar (L) into place.
Insert Cam Locks and Wood Screws (short) into the pre-drilled holes
of Back Stretchers (G) and (H) and tighten.
Page 5
Q
Assembly
A
Instructions
5/6
S
S
Adjustable Pin
STEP 7
Attach Top (A) to the unit with Cam Locks.
R
T
T
T
Insert Adjustable Pins into side panel and middle panel at the desired level.
Place Shelves (S) into position.
Attach Doors (Q) and (R) by sliding the door lift hinges into the
side panels lift hinges. (See Figure 7)
Assemble Pull Handles to Doors with
Machine Screws. (See Figure 8)
Slide Drawers (T) into position.
Figure 7
Figure 8
Page 6
Drawer (T)
T3
T2
MAKE SURE ROLLER
IS ON THE BACK
Figure 1
STEP 2
T1
Assembly Instructions 6/6
STEP 1
Attach T1 to T3 and T4,
using a screwdriverPhillips
and wood screws (4X),long
tighten halfway.
T4
Attach T2 to T3 and T4 using
wood screws (4X),long
tighten halfway. (See Figure 1)
Slide T5 into the grooves in T3
and T4. Be sure to push T5 all
the way forward so it meets T1.
(See Figure 2)
T3
T5
T2
Figure 3
STEP 3
Insert wood screws (4X)short
into the pre-drilled holes in T5,
tighten screws. (See Figure 3)
T1
T4
T3
T1
T5
T4
T2
Figure 2
STEP 4
Assemble Pull Handle with
machine screws. (See Figure 4)
Tighten all screws used in drawer assembly.
Figure 4
Part List
T1.
Front Part
3 pcs.
T2.
Back Part
3 pcs.
T3.
Side Part
3 pcs.
T4.
Side Part
3 pcs.
T5.
Base Part
3 pcs.
Loading...