Red Barrel Studio W004780411 Installation & Assembly

Assembly Instructions

Caution : You must read this before you proceed.

BARSTOOL

CAUTION : This Barstool is NOT a TOY.

Keep your child / children at bay during the assembly process.
For moving the Barstool and to prevent damage to the Barstool two adults may be
needed to execute this action.

Noble House Home Furnishings LLC

Parts List

NO. Picture QTY

A 1

B 1

C1 1

Chair Back

Chair Seat

Left Front Leg (Labelled C1)

Description

C2 1

Right Front Leg (Labelled C2)

Side Rail
(The side with holes is the bottom

D 2

side to face the floor after
assembly)

E Front Rail 1

Hardware

1

2

3

Long Bolt (M8x75mm)

Short Bolt (M8x40mm)

Flat Washer

5

7

11

4

5

66

67

Screw (M4x50mm)

Spring Washer

Allen Key

Screwdriver

Noble House Home Furnishings LLC

7

11

1

Not provided

Assembly Preparation

Before Beginning Assembly:

Assembly Steps

OVERVIEW

Chair Seat (B)

Side Rail (D)

Left Leg (C1)

Front Rail (E)

Chair Back (A)

Side Rail (D)

FRONT FACING

This Chair has multiple parts and may require up to 30 minutes to assemble. To give
you an overview of the Chair, the above picture is to help you put the various parts
into perspective. Please read through the instructions below to familiarise yourself
with the parts and steps before assembly.

Noble House Home Furnishings LLC

Right Leg (C2)

Step 1

C

4

4

Unpack and place all parts on a clean, non-marring surface.

Step 2

C

Step 2.1

7

7

E

Step 2.2

Attach Front Rail (E) into the housing of the Left Front Leg(C1) and Right Front
Leg(C2).

2.1) Secure the Front Rail (E) to Left Front Leg(C1) by using Screw (④) and
Screwdriver (⑦).

2.2) Secure the Front Rail (E) to Right Front Leg(C2) by using Screw (④) and
Screwdriver (⑦).

Do not fully tigthen Screws.

Noble House Home Furnishings LLC

Step 3

Place the Chair Back(A) onto a flat, clean table, as shown above.
Attach Chair Seat(B) with wooden dowel to the housing of Chair Back(A)
Secure Chair Seat(B) to the Chair Back(A), using Short Bolt(②) Spring Washer(⑤)
and Flat washer(③) with Allen Key(⑥).

Do not fully tigthen Bolts.

Step 4

Secure Chair Seat(B) to the Chair Back(A), using Long Bolt(①) Spring Washer(⑤)
and Flat washer(③) with Allen Key(⑥).

Do not fully tigthen Bolts.

Noble House Home Furnishings LLC

Step 5

Then, place the Chair onto the side of a table as shown in picture. You will have the
chair bottom and legs facing skywards.
Attach the assembled frame from Step 2 into the assembled frame from Step 3 by
using Short Bolt(②), Spring Washer(⑤) and Flat washer(③) with Allen Key(⑥).

Do not fully tigthen Bolts.

Noble House Home Furnishings LLC

Step 6

Next place Side Rail(D) into the housing of the Hind Leg of the Chair Back(A) and Left

4

Step 6.1

7

C1

D

A

Step 6.2

7

4

A

Front Leg(C1).
You may need to apply a little pressure to the Legs - pushing outwards, so as to
enable the Side Rail(D) to be slotted into position.

6.1) Secure the Side Rail(D) to Left Front Leg(C1) using Screw(④) and
Screwdriver(⑦).

6.2) Secure the Side Rail(D) to Chair Back(A) using Screw(④) and Screwdriver(⑦).
Do not fully tigthen Screws.

Repeat the same process for the other Side Rail(D) to Right Front Leg(C2).

Noble House Home Furnishings LLC

Step 7

If wobble

Test again

30cm­50cm

Place the Chair right side up on a LEVEL SURFACE to see if it wobbles.
If it wobbles, lift the Chair some 30cm to 50cm height from the ground.
Keep your feet and toes well away from the drop zone.

Drop the Chair freely and vertically with all four legs, hitting the ground at the same
time.
This Drop Test will help to ensure that all the Bolts, Screws and gaps reach full
alignment status.
Test again for evenness on a LEVEL SURFACE.
If no wobbles are found, proceed to tighten all the Screws, and Bolts.

When tightening these screws, tighten sequentially.
Do not tighten any Bolt, or Screw fully and then move towards the next one.
This could cause the frame to warp.
If there are still wobbles, loosen the Screws and Bolts and execute the same
drop tests.
If the Chair is not stable it could lead to damage to the product.

Step 8

Inspect the Chair and make sure all parts are connected.
Your Chair is ready for use.

This Chair can only be used on a flat, level surface.

Noble House Home Furnishings LLC

Care & Maintenance

What is Proposition 65?

Proposition 65 is a California law that requires warning labels on products that may contain one of more than 800­plus chemicals or ingredients that the California Office of Environmental Health Hazard Assessment (OEHHA) has
deemed to cause cancer or other reproductive toxicity. Chemicals and elements on this list include wood dust,
brass, and other everyday substances, which can be found in very common household items, such as: lamps,
tableware, jewelry, crystal glasses, electric cords, beauty products, automobiles, and furniture.

Why Did I Find a Proposition 65 Warning on My Home Goods Product?

We include Proposition 65 warnings on all of our products because there is always a chance that one of the 800­plus common chemicals and ingredients listed under this law could potentially be on our furniture or packing
materials. We risk large fines under this law, if we don't include this warning.

Should I worry?

We realize you may be worried finding this warning on our products, but we want to reassure you that the hazardous
exposure limits for any of these chemicals have never been found on furniture products that we’ve shipped to our
customers. Additionally, this warning label is very common and can be found on almost every piece of furniture sold
in the state of California.

Just How Common Are Proposition 65 Warnings?

Proposition 65 warnings have become so common in California that it is hard to take a trip to a local bank, grocery
store, or restaurant without finding at least one warning. In fact, even the Disney Land Resort has a Proposition 65
warning:

Noble House Home Furnishings LLC