Page 1
CHAIR
1 of 9
CAUTION: You must read this before you proceed.
CAUTION : This Chair is NOT a TOY.
Keep your child / children at bay in the process of assembly.
For turning the Chair and to prevent damage to the Chair, 02 persons may be needed
to execute this action.
Page 2
No. Picture Description Qty
2 of 9
A Backrest Panel 1
B1 Right Leg Panel 1
B2 Left Leg Panel 1
C Seat Panel 1
D1 Front Footrest 1
D2 Back Footrest 1
E Seat Cushion 1
No. Picture Description Qty
①
②
Allen Key 2
Bolt (M6*40mm) 3
③
④
Sleeve nut (M6*15mm) 3
Screw (M6*60mm) 11
Page 3
Before Beginning Assembly:
3 of 9
OVERVIEW
Left Leg
Panel (B2)
Backrest
Panel (A)
Back Footrest
(D2)
Right Leg
Panel (B1)
Seat
Cushion (E)
Seat Panel
(C)
Front
Footrest (D1)
FRONT FACING
This Chair has multiple parts and may require up to some 30 minutes to
assemble. To give you an overview of the Chair, the above picture is to
help you put the various parts into perspective. Please read through the
instructions here below to familiarise the parts and steps before assembly.
Page 4
Step 1
4 of 9
Unpack and place all parts on a clean, non-marring surface.
Step 2
Step 2.1
A
A
C
B2
C
Step 2.2
B1
2.1) Position Backrest Panel (A) and Seat Panel (C) to Left Leg Panel (B2)
as shown in picture above
2.2) Position Right Leg Panel (B1) onto Backrest Panel (A) and Seat Panel
(C)
Page 5
Step 3
5 of 9
Step 3.1
B1
C
2
3
A
1
Step 3.2
1
4
3.1) Secure Right Leg Panel (B1) to Seat Panel (C) by using Bolt (②),
Sleeve Nut (③) and Allen Key (①)
3.2) Secure Right Leg Panel (B1) to Seat Panel (C) and Backrest Panel (A)
by using Screw (④) and Allen Key (①)
Do not fully tighten the Bolts and Screws.
Step 4
Step 4.2
Step 4.1
B1
C
B2
D1
4
D2
1
4.1) Position Front Footrest (D1) and Back Footrest (D2) to Right Leg
Panel (B1) and Left Leg Panel (B2) as picture shown
4.2) Secure Right Leg Panel (B1) to Front Footrest (D1) and Back Footrest
(D2) by using Screw (④) and Allen Key (①)
Do not fully tighten the Screws.
Page 6
Step 5
6 of 9
A
1
2
3
C
B2
D1
D2
1
4
With assistance from your adult partners, turn the Chair into the other side
Repeat the same process of step 3 and 4 to secure Left Leg Panel (B2)
with Backrest Panel (A), Seat Panel (C), Front Footrest (D1) and Back
Footrest (D2)
Do not fully tighten the Bolts and Screws.
Page 7
Step 6
7 of 9
If wobble
Test again
30cm-50cm
Place the Chair right side up on a LEVEL SURFACE to see if it wobbles.
If it wobbles, lift the Chair 30cm to 50cm high from the ground.
Keep your feet and toes well away from the drop zone.
Drop the Chair freely and vertically with all four legs, hitting the ground at
the same time.
This Drop Test will help to ensure that all the Bolts, Screws and gaps reach
full alignment status.
Test again for evenness on a LEVEL SURFACE.
If no wobbles are found, proceed to tighten all the Bolts, Screws.
When tightening the Bolts, Screws, tighten sequentially.
Do not tighten any Bolt, Screws fully and then move towards the next
one.
This could cause the frame to warp.
If there are still wobbles, loosen the Bolts, Screws and execute the
same drop tests.
If the Chair is not stable it could lead to damage to the product.
Page 8
Step 7
8 of 9
E
C
Inspect the Chair and make sure all parts are connected.
Place Seat Cushion (E) on to the Chair
Lay down the Chair and tie the velcro straps of Cushion (E) to Seat Panel
(C) as shown above.
Your Chair is ready for use.
This Chair can only be used on a flat, level surface.
Page 9
9 of 9
Loading...