Page 1
IMPORTANT SAFETY INSTRUCTIONS
• To avoid injury or damage, mount only on a surface that is sturdy.
• To avoid electric shock, make sure the electricity is turned off at the main
circuit breaker panel. If you are replacing an existing fixture, turn off the
following in order: fixture, wall switch, and main fuse or breaker box.
Note: Some types of fuses must be unscrewed to shut the power off.
• If you are unclear as to how to proceed, please consult a licensed
electrician.
UNPACK THE FIXTURE: Check the contents of the box. Box should contain all items on the parts diagram.
INSTALLATION INSTRUCTIONS
1. Secure Mounting Plate (A) to the junction box (not included) using Mounting Screws (B) provided. Ensure
the attached Screw Collar Loop (E) is pointing down towards the floor.
2. Remove Threaded Ring (F) from Screw Collar Loop (E) by unscrewing it in a counter-clockwise direction.
Set Threaded Ring (F) aside.
3. Place Canopy (D) against the ceiling with Screw Collar Loop (E) protruding through the hole in Canopy (D).
Adjust Screw Collar Loop (E) and the hex nut above it until 3/8" of the threaded portion of Screw Collar
Loop (E) is visible. Remove Canopy (D) and set it aside.
4. Secure Pendant Loop (I) to the top of Fixture Body (J) by screwing it in a clockwise direction.
5. Assemble one end of Chain (G) to Pendant Loop (I) by carefully pulling apart the chain link and closing it
around Pendant Loop (I) with chain pliers.
6. With chain pliers, remove excess Chain (G) to achieve desired hanging length. Once Chain (G) is to desired
length, use wire cutters to cut Wire (H) 10” beyond the length of Chain (G) to allow for easier wire
connection.
7. Weave Wire (H) upwards through every 4-5 links in Chain (G).
For any replacement parts or installation issues, please Contact Us!
Page 2
8. Slide Threaded Ring (F) down Chain (G) and Wire (H) with the raised end (flange) facing up towards the
ceiling. Slide Canopy (D) down Chain (G) and Wire (H).
Note: Threaded Ring (F) and Canopy (D) will be used to secure fixture to ceiling at a later
step.
9. Spread out arms on Fixture Body (J) evenly to create the chandelier design. Secure Ring (L) to bottom of
Fixture Body (J) with Decorative Screws (M).
10. Open the top chain link with chain pliers and carefully lift Fixture Body (J) (with the help of a friend). Close
the chain link around Screw Collar Loop (E).
11. Insert the end of Wire (H) through the hole in Screw Collar Loop (E) into the junction box.
12. Using the wire graph below, connect the appropriate wires from the fixture to the corresponding wires in
the electrical junction box (not included) and secure Wire Connectors (C).
A. Connect the ground wire (bare copper or green) from
your fixture to the:
1) ground wire in the junction box, or
2) ground screw in the junction box
B. Connect the BLACK house wire to fixture hot wire
that corresponds to diagram (black, round & smooth,
white/grey with tracer, brown/gold without tracer).
C. Connect the WHITE house wire to fixture neutral wire
that corresponds to diagram (white, ribbed/ridged,
white/grey without tracer, brown/gold with tracer).
13. Place all Wires (H) and Wire Connectors (C) back into the junction box.
14. Slide Canopy (D) and Threaded Ring (F) up Chain (G) and Wire (H). Place Canopy (D) flush against the
ceiling and secure in place by screwing Threaded Ring (F) onto Screw Collar Loop (E) in a clockwise
direction.
15. Install bulbs (not included) into Socket (K).
Enjoy your new fixture!
Page 3
PARTS DIAGRAM
HELPFUL TOOLS: Safety Goggles, Screwdriver, Wire Cutter/Stripper, Ladder, Measuring Tape, Chain Pliers
Loading...