Page 1
NOTE : This Bed is NOT a TOY.
Keep your child / children at bay during the assembly process.
The BED is HEAVY.
To prevent injury to yourself or damage to the product a minimum of two adults are required
whenever moving or lifting the product.
Queen Size Bed
CAUTION: You must read this before you proceed.
1 OF 11
Page 2
No. Picture Description Qty
A Headboard 1
B Headboard Panel 1
C Headboard Left Foot 1
D Headboard Right Foot 1
E
Side Panel
2
F Footboard 1
G
Cross Slat With
Mounting Positions
3
H
Cross Slat Without
Mounting Positions
8
2 OF 11
Page 3
I Vertical Slat 1
J
Support Foot for
Vertical Slat
3
K Footboard Foot 2
No. Picture Description Qty
①
Bolt (M8x50mm) 11
②
Spring Washer 11
③
Washer 11
④
Allen Key 1
⑤
Screw
(2cm self-tapping)
2
⑥
Screw
(5cm self-tapping)
2
⑦
Metal Brackets 4
⑧
Restraint Strap 2
⑨
Screwdriver Not Provided
3 OF 11
Page 4
Unpack and
place all
parts for
clear
visibility.
Bolt(①)
Spring Washer(②)
Washer(③)
Allen Key(④)
Screw(⑤)
Screw(⑥)
Metal Bracket(⑦)
Restraint Strap(⑧)
Pack A:
Hardware for
assembly of
Bed.
Before Beginning Assembly:
4 OF 11
Page 5
Step 1
1.1
1.2
OVERVIEW
This Bed has multiple parts and may require up to 60 minutes to assemble. To give you
an overview of the Bed parts, the above picture is to help you put the various Bed parts
into perspective. Please read through the instructions below to familiarise yourself with
the parts and steps before assembly.
A
C
D
①
②
③
④
Headboard(A)
Headboard Left
Foot(C)
Headboard Right Foot(D)
Side
Panel(E)
Side
Panel(E)
Footboard(F)
Footboard
Foot(K)
Footboard
Foot(K)
Cross Slat With
Mounting Positions(G)
Cross Slat Without
Mounting Positions(H)
Cross Slat Without
Mounting Positions(H)
Support Foot For
Vertical Slat(J)
Vertical
Slat(I)
Headboard
panel(B)
5 OF 11
Page 6
Step 2
Attach Side Panel(E) to Footboard(F) by sliding the Metal Plates onto the Bolts as shown.
First insert the Metal Plate, then press it down lightly.
The Side Panel(E) should rest on the Footboard Foot(K).
Attach Footboard Foot(K) to Footboard(F) by inserting the threaded stem of the Foot and turning
clockwise until secure.
The bulge from the Leg should face inside when finished.
Step 3
1.1) Place the Headboard(A), Headboard Panel(B), Headboard Left Foot(C) and Headboard Right
Foot(D) into position as shown.
1.2) Attach the Headboard Left Foot(C) and Headboard Right Foot(D) to Headboard(A) using Bolts(①),
Spring Washers(②), and Washers(③) with Allen Key(④).
Then, attach the Headboard Left Foot(C) and Headboard Right Foot(D) to Headboard Panel(B) using
Bolts(①), Spring Washers(②), and Washers(③) with Allen Key(④).
Tighten the Bolts fully in a sequential manner.
E
K
E
F
E
F
K
K
F
6 OF 11
Page 7
5.1) Place the Vertical Slat(I) with “Face up" label down.
5.2) Attach Support Foot for Vertical Slat(J) to the bottom of Vertical Slat(I) by inserting the threaded
stem in the Foot and turning clockwise until secure.
5.3) Stand the Vertical Slat upright.
Step 5
5.1
5.2
5.3
Step 4
Attach Side Panel(E) to Headboad Left Foot(C) and Headboad Right Foot(D) by sliding the iron plates
onto the Bolts as shown.
A
K
F
E
B
C
D
K
E
C
I
Labelled "Face Up"
Labelled "Face Up"
I
J
I
J
7 OF 11
Page 8
Step 7
6.1) Put the Cross Slats(G) into the grooves of the Side Rails(E).
6.2) Attach Vertical Slat(I) to the bottom of Cross Slats(G) using Bolts(①) and Washers(③) with Allen
Key(④).
Tighten Bolts until fully secure in a sequential manner.
Step 6
6.1
6.2
H
E
8 OF 11
Page 9
Put the Cross Slats(H) into the grooves of the Side Rails(E).
Step 8
Ensure that all Bolts are secured at all joints.
Your Bed is ready for use.
This Bed can only be used on a flat, level surface.
Heardboard Restraint Device Installation Instruction
Locate the two marks on Headboard(A).
Then, Attach the Metal Brackets(⑦) to the back of Headboard(A) using Screws(⑦) with
Screwdriver(⑩) as shown above.
Tighten Screws until firm and secure.
WARNING
Serious or fatal crushing injuries can occur from tipping furniture. To help prevent tip-
over: ALWAYS secure this furniture to the wall using a Safety Restraint Device. See
product instructions for more ways to help prevent furniture tip-over.
9 OF 11
Page 10
Put the Headboard against the wall where desired and mark the location for the Metal Brackets(⑦) to
be the same height as the top of the Headboard.
Attach Metal Bracket(⑦) to the wall where you marked using Screws(⑥) with Screwdriver(⑨).
Repeat this process with the other Metal Bracket(⑦).
Note: The Metal Brackets need to be secured to solid, load bearing surface. Please use a Stud
Finder(not supplied) if needed to locate the Wall Frame.
Move the Headboard back against wall.
Pull the Restraint Straps(⑧) through the Metal Brackets(⑦) on the wall and Headboard(A) one by one,
and pull the Restraint Straps(⑧) tight.
The strap between Headboard and Metal Brackets on wall should be within 3.5''.
⑥
⑦
⑥
⑦
⑧
⑦
⑦
⑤
⑥
Metal Bracket on
the back side of
Headboard
Metal
Bracket on
the wall
Within 3.5''
10 OF 11
Page 11
Loading...