Red Barrel Studio W003172476 Installation & Assembly

Caution : You must read this before you proceed

Bar Stool/Counter Stool

Page 1 OF 8

Label Picture Description QTY

A Backrest 1 pc

B Wooden Leg 4 pcs
C Leg Frame 1 pc

D Swivel Plate 1 pc

E Cushion Seat 1 pc

Label Picture Description QTY

①

Bolt : M6 x 40mm 10 pcs

②

Bolt : M6 x 35mm 8 pcs

③

Bolt : M6 x 25mm 4 pcs

④

Spring Washer M6 x 13mm 18 pcs

⑤

Flat Washer M6 x 13mm 12 pcs

⑥

Flat Washer M6 x 16mm 10 pcs

⑦

Allen Key 1 pc

Page 2 OF 8

Pack A - for
assembling the
Wooden Leg (B) to
the Leg Frame (C)

4 Bolt M6 x 40mm
4 Spring Washer M6 x 13mm
4 Flat Washer M6 x 13mm
1 Allen Key

Pack B - for
assembling the
Wooden Leg (B) to
the Swivel Plate (D)

8 Bolt M6 x 35mm
8 Spring Washer M6 x 13mm
8 Flat Washer M6 x 13mm

Pack C - for
assembling the
Backrest (A) to the
Cushion Seat (E)

6 Bolt M6 x 40mm
6 Spring Washer M6 x 13mm
6 Flat Washer M6 x 16mm

Pack D - for
assembling the
Swivel Plate (D) to
the Cushion Seat
(E)

4 Bolt M6 x 25 mm
4 Flat Washer M6 x 16mm

Before Beginning Assembly :

Page 3 OF 8

A. Backrest B. Wooden Legs C. Leg Frame

D. Swivel Plate

E. Cushion Seat

This Bar Stool/Counter Stool has multiple parts and may require up to 30 minutes to assemble. To give
you an overview of the Bar Stool/Counter Stool parts, the above picture is to help you put the various Bar
Stool/Counter Stool parts into perspective. Please read through the instructions to familiarise yourself with
the parts and steps before assembly.

Overview

Step 1

Place the Backrest (A) and Wood Legs (B)，Leg Frame (C), Swivel Plate (D) & Cushion Seat (E) on a
soft surface to avoid any scratches or damages to the product and take out all the hardware.

FRONT FACING

Leg Frame (C)
Wooden Leg (B)

Swivel Plate (D)

Cushion Seat (E)

Backrest (A)

Page 4 OF 8

Step 2

3.1 Position the assembled component upright.

Align Wooden Leg (B) top end to the notch of the Swivel Plate (D).

3.2 Then, affix the Wooden Leg (B) and Swivel Plate (D) with Bolt② , Spring Washer④ , Flat Washer …⑤
, Allen Key  by using Hardware Pack B.

Place and partially screw in all bolts.
Then fasten the Bolts,DO NOT FULLY TIGHTEN THE BOLTS.
Repeat the same process with the remaining legs.

3.1

Place the Wooden Leg (B) and Leg Frame (C) on a clean, non-marring surface to avoid any scratch or
damage to the product.
Pick up one Wooden Leg (B) and align to the notch at the Leg Frame (C).

use the Bolt •①, Spring Washer④ „, Flat Washer …⑤, Allen Key⑦ by using Hardware Pack A.
Repeat the same process with the remaining legs.
At this stage, DO NOT FULLY TIGHTEN these Bolts.

WARNING ! FULLY TIGHTEN COULD LEAD TO DAMAGE OF THE PRODUCT .TIGHTEN ONLY
UNTIL SECURE AND STABLE.

Step 3

3.2

Pack A

Pack B

Page 5 OF 8

Step 4

5.1 Keep the chair still turned upside down. (legs facing skywards) on the table for the final leg of this

assembly process.
Place the assembled Swivel Plate (D) upside down to the seat frame as shown above.

5.2 Turn the Swivel Plate (D) to 45° degree position as shown above.
Align the mounting Position of the Swivel Plate (D) to the the mounting Position of the Seat Frame.

Affix the with Swivel Plate (D)with the Bolt③, Flat Washer⑥, and Allen Key⑦by using Hardware Pack
D.
Partially Screw in these four Bolts into the Swivel Plate (D).
Turn in all the Bolts.
At this stage, FULLY TIGHTEN THE BOLTS.

Step 5

5.2

5.1

4.1 4.2

4.1 Place the Cushion Seat (E) upside down on a table edge.

Align the Backrest Panel to the Seat Frame.

4.2 Align the mounting position of the Cushion Seat (E) to the mounting position in Backrest (A) .
Affix the Backrest frame to the Seat Frame with the Bolt , Spring Washer④ , Flat Washer ⑥and Allen

Key ⑦by using Hardware Pack C.
Partially drive in all the Bolts in this part of assembly.
Once all Bolts in position, turn in these Bolts.
At this stage,FULLY TIGHTEN THE BOLTS.

D

Pack C

Pack D

Page 6 OF 8

Step 6

Step 7

Ensure that all the Bolts are fully driven in and locked in.
Turn this Bar Stool/Counter Stool right way up and ensure this Bar Stool/Counter Stool is stable.
Place the Bar Stool/Counter Stool on a level Surface to check if it wobbles.
If it is wobbles, lift the Bar Stool/Counter Stool some 30cm to 50 cm high from the ground.
Keep your feet and toes well away from the drop zone.
Drop chair freely and vertically,with the four legs hitting the ground at the same time.
This Drop Test will help to ensure that all the Bolts and gaps to all reach full alignment status.
Test again for evenness on a Level Surface.
If no wobbles are found, proceed to tighten all the Bolts.

Caution: When tightening the Bolts, tighten sequentially.
Do not fully tighten PACK A& PACK B during Step 2 and Step 3 and then towards the next one.
This may cause the frame to warp.
If there is still wobbles, loosen the bolts PACK A& PACK B during Step 2 and Step 3. and execute
this same drop test.
WARNING !! DO NOT FULLY TIGHTEN PACK A& PACK B during Step 2 and Step 3.
FULLY TIGHTENING COULD LEAD TO DAMAGE OF THE PRODUCT.
TIGHTEN ONLY UNTIL SECURE AND STABLE.

The Bar Stool/Counter Stool now is ready for use.
After a period of use, you may find the Bar Stool/Counter Stool joints, may become loose.
Get the Allen Key and tighten up all Bolts.
This Bar Stool/Counter Stool can only be used on a flat, level surface.

Page 7 OF 8

Page 8 OF 8