Page 1
ASSEMBLY AND INSTALLATION
INSTRUCTIONS
TO AVOID RISK OF ELECTRICAL SHOCK, BE SURE TO SHUT OFF
TO AVOID RISK OF ELECTRICAL SHOCK, BE SURE TO SHUT OFF
WARNING:
NOTE: 1. Before installing, consult local electrical codes for wiring and grounding requirements.
2. READ AND SAVE THESE INSTRUCTIONS.
Hardware Package (included):
POWER BEFORE INSTALLING OR SERVICING THIS FIXTURE.
POWER WHILE INSTALLING OR SERVICING THIS FIXTURE.
Mounting plate (A)
Green Grounding Screw (E)
Outlet Box
House Grounding Wire
Green Grounding Screw (E)
Mounting Plate (A)
Mounting Screw (B)
Headless Screw (D)
Lock Nut (F)
Fixture Grounding Wire
Mounting Screw (B)
Lock Nut (F)
Wire Connector (C)
Photocell
Back Plate
Fixture
Wire
Wire Connector (C)
Ball Nut (G)
Headless screw (D)
Rubber Pad (H)
Rubber Pad (H)
Ball Nut (G)
Bulb Type B
Max.60W
(not included)
IMPORTANT:
The sensor has an excellent photocell function
to enable the light to turn on at dusk and off at
dawn automatically.
Metal Frame
Installation Steps
Turn off the power at fuse or circuit box
1. Thread two headless screws (D) through the mounting plate (A), and then secure them with four lock nuts (F) (two on each
side of the mounting plate (A).) Adjust the length of the headless screws (D) if necessary.
Note: Make sure the headless screws are lined up horizontally to make the fixture level.
2. Attach the mounting plate (A) to the outlet box by using two mounting screws (B).
Page 2
3. Make the bottom of the fixture upward, gently place four glass panels into the
metal frame, then press the clips to secure the glass panels. (Fig.1)
Glass Panel
Note: The patterned side of faces glass out.
4. Pull out the source wires from the outlet box. Make wire connections using wire
connectors (C) as follows:
---Connect the hot wire (usually black insulation) from the fixture to the
Clip
black wire from the power source.
---Connect the neutral wire (usually white insulation) from the fixture to the
white wire from the power source.
Metal
Frame
Fig.1
---Attach the fixture grounding wire (usually green insulation or bare wire) to
the mounting plate (A) with the green grounding screw (E), and then
connect it to the house grounding wire with the wire connector (C).
Carefully put the wires back into the outlet box.
5. Attach the fixture to the mounting plate (A) by inserting headless screws (D) into holes on back plate, and then secure
it with two rubber pads (H) and two ball nuts (G).
NOTE: With silicone caulking compound,caulk complete around the back plate meets with the wall surface to
prevent water from seeping into the outlet box.
6. Install three bulbs (not included). See relamping label at socket area or packaging for maximum allowed wattage.
Turn on the power at fuse or circuit box
Operation the Unit Without Photocell
Photocell
Black wires From Photocell
White Wires From Photocell
Red Wires From Photocell
Wire Connector
Wires From Fixture
White Pigtail
Fig.
Wires From Fixture
Pigtail
Wire Connector (C)
2
1. Turn off the power at the fuse or circuit box before starting installation.
2. Loosen the wire connector connected with the wires from photocell. (See Fig.2)
Note: Do not move the photocell to prevent water from seeping into the outlet box.
3. Take a white pigtail and black pigtail and make wire connections using wire connector (C): (See Fig.3)
a. The black wire from the fixture to one end of the black pigtail.
b. The white wire from the fixture to one end of the white pigtail.
c. The other end of the black pigtail to the black wire from the power source.
d. The other end of the white pigtail to the white wire from the power source.
Put all wires back into the back plate of the fixture.
Wires From
Main Power
.3
Fig
Turn on the power at fuse or circuit box.
Page 3
The following parts are available for re-order if damaged or missing.
Spare Parts List:
Mounting Hardware
(1SET)
Mounting plate (A)
Green Grounding Screw (E)
Mounting Screw (B)
Lock Nut (F)
A
Wire Connector (C)
Ball Nut (G)
B
Headless screw (D)
Rubber Pad (H)
Glass Panel
A: 10"
B: 26-1/2"
C: 11-1/4"
C
Loading...