Red Barrel Studio W002380761 Installation & Assembly

Label Picture Description QTY

A

Left Armrest

(with Legs)

1

B

Right Armrest

(with Legs)

1

C

Backrest

(with Legs)

3

D Seat Panel 3

E

Front Panel

(with Legs)

3

Caution : You must read this before you proceed

3 Seater

Page 1 OF 11

F Left Front Foot Clip 1

G Right Front Foot Clip 1

H Left Back Foot Clip 1

I Right Back Foot Clip 1

J Front Middle Foot Clip 2

K Back Middle Foot Clip 2

L

Inner Panel

(with Legs)

2

M Seat Cushion 3

Q Rubber Hammer 1

Before

Beginning

Assembly:

Page 2 OF 11

Step 1

Open the carton and place all parts on a clean, non-marring surface.
Place the two Front Panels(E) facedown on the clean, non-marring surface.
Insert the Clasps of the Front Panel(E) into the large part of Pear-shaped Clasp mounting positions of the
other Front Panel(E) as shown above.
Button up the Clasps with the Rubber Hammer(Q) as pictured.

Overview

This 3 Seater has multiple parts and may require up to 60 minutes to assemble. To give you an overview of
the 3 Seater parts, the above picture is to help you put the various parts into perspective. Please read
through the instructions below to familiarise yourself with the parts and steps before assembly.

Left Armrest (A)

Seat Cushion (M)

Backrest (C)

Front Panel (E)

Front Facing

Right Armrest (B)

Seat Panel (D)

Right Front Foot Clip (G)

Left Front Foot Clip (F)

Left Back Foot Clip (H)

Front Middle Foot Clip (J)

Clasp

Pear-shaped Clasp

Mounting Position

Page 3 OF 11

Step 2

Insert the Clasps of the Front Panel(E) into the large part of Pear-shaped Clasp mounting positions of the
other Front Panel(E) as shown above.
Button up the Clasps with the Rubber Hammer(Q) as pictured.

Step 3

Align Inner Panel(L) to Middle Panel(E) as pictured above.
Insert the Dowel of the Inner Panel into the mounting position of the Middle Panel until it clicks into place.
Repeat this process with the remaining Inner Panel(L).

Dowel

Pear-shaped Clasp

Mounting Position

Clasp

Page 4 OF 11

Step 4

Place the Seat Panels(D) facedown on the clean, non-marring surface.
Insert the Clasps of the Seat Panel(D) into the large part of Pear-shaped Clasp mounting positions of the
other Seat Panel(D) and push down to button up the Clasps with the Rubber Hammer(Q).

Step 5

Insert the Clasps of the Seat Panel(D) into the large part of Pear-shaped Clasp mounting positions of the
other Seat Panel(D) and push down to button up the Clasps with the Rubber Hammer(Q).

Another side of Seat Board (D)

Page 5 OF 11

Step 7

Place the Backrests(C) on the clean, non-marring surface.
Insert the Clasps of the Backrest(C) into the large part of the Pear-shaped Clasp mounting positions on the
other Backrest(C).
Button up the Clasps with the Rubber Hammer(Q) as pictured.

Step 6

With help from an adult partner, insert Front Panels(E) and Inner Panels(L) into Seat Panels(D) using the
interlocking joints with Rubber Hammer(Q).

Page 6 OF 11

Step 8

Insert the Clasps of the Backrest(C) into the large part of the Pear-shaped Clasp mounting positions on the
other Backrest(C).
Button up the Clasps with the Rubber Hammer(Q) as pictured.

Step 9

With help from an adult partner, place the Backrests(C) on the Seat Panels(D) and Inner Panels(L) as
shown above.
Insert the Clasps of the Seat Panels(D) and Inner Panels(L) into the large part of Pear-shaped Clasp
Mounting Positions of the Backrests(C).

Page 7 OF 11

Step 10

With the help of your adult partner, stand the assembly upright.
Button up the Clasps with the Rubber Hammer(Q) left to right as pictured.

Step 11

Align the Left Armrest(A) to the left side of Backrest(C), Seat Panel(D), and Front Panel(E).
Insert the Clasps on the Left Armrest(A) into the Pear-shaped Clasp mounting positions on the Front
Panel(E), Seat Panel(D), and Backrest(C).
Insert the 8 Clasps of Front Panel(E), Seat Panel(D), and Backrest(C) into Pear-Shaped Clasp mounting
positions of Left Armrest(A).
Button up the Clasps with the Rubber Hammer(Q) from left to right as shown above.

Page 8 OF 11

Step 13

Attach the Left Front Foot Clip(F), Right Front Foot Clip(G), Left Back Foot Clip(H), Right Back Foot Clip(I),
Front Middle Foot Clips(J), and Back Middle Foot Clips(K) to the feet of the 3 Seater using the Rubber
Hammer(Q) as shown above.

Step 12

Repeat the process from Step 10, to assemble the Right Armrest(B)

Page 9 OF 11

Step 14

With the help of your adult partner, stand the 3 Seater up on a Lever surface, to check for wobbles.
If there are wobbles, use the Rubber Hammer(Q) to ensure all parts are properly secured.

Step 15

Place the Cushion(M) on the seat.
Your 3 Seater is ready for use.

This 3 Seater can only be used on a flat, level surface.

Page 10 OF 11

Page 11 OF 11