Page 1
Kitchen Cart
IMPORTANT
Carefully remove all the parts from the carton and
place them individually on a soft cloth to prevent
scratches or other damage.
Carefully and strictly follow these assembly instructions
to ensure a completed product as designed.
Do not use power tools above 8 volts to assemble.
Part List
Side Panel
A.
To p
1 pc.
W.
Front Rail
1 pc.
B.
1 pc.
C.
Side Panel
1 pc.
D.
Middle Panel
1 pc.
E.
Back Panel
3 pcs.
F.
Back Upright
2 pcs.
K.
Arm
2 pcs.
L.
Towel Bar
1 pc.
Hardware List
N.
Rack Side
1 pc.
M.
Rack Side
1 pc.
G.
Back Rail
1 pc.
H.
Back Rail
1 pc.
P.
Rack
1 pc.
O.
Rack Base
1 pc.
Q.
Door
1 pc.
I.
Front Rail
2 pcs.
S.
Shelf
2 pcs.
J.
Base
1 pc.
U.
Leaf
R.
Door
Support
1 pc.
1 pc.
T.
Drawer
3 pcs.
Refer to later page(s) of these
instructions for drawer assembly.
V.
Leaf
Support
1 pc.
M6x38
Head Cap Bolt (long)
4 pcs. (+1 extra)
M6x25
Head Cap Bolt
4 pcs. (+1 extra)
Caster
2 Locking
2 Non-Locking
4 pcs.
Hex Wrench
1 pc.
Small
Hex Wrench
1 pc.
Magnet
2 pcs.
M3x16
Wood Screw
for Magnet
4 pcs. (+1 extra)
Tool(s) required for assembly: Phillips screwdriver
M3.5x16
Wood Screw (short)
24 pcs. (+1 extra)
M6x12
Head Cap Bolt
for Caster
16 pcs. (+1 extra)
M3.5x25
Wood Screw (long)
24 pcs. (+1 extra)
M3x16
Wood Screw
for Leaf Support
6 pcs. (+1 extra)
M3.5x25
Flat Head Screw
3 pcs. (+1 extra)
Adjustable Pin
8 pcs. (+1 extra)
Knob
5 pcs.
M4x25
Machine Screw
5 pcs.
Page 2
Assembly Instructions 2/7
IMPORTANT
Use a soft cloth between these parts and the floor.
Do not use power tools above 8 volts to assemble.
Do not tighten all the bolts until each part is properly assembled.
Keep Hex Wrench as the bolts may need to be tightened in the future.
N
STEP 1
Assemble Rack Sides (M), (N), Rack Base (O) and Rack (P).
STEP 2
Attach unit to Side Panel (C) with Head Cap Bolts.
M
O
P
Head Cap Bolt
C
K
Head Cap Bolt
K
B
STEP 3
Attach Arms (K) to Side Panel (B) with Head Cap Bolts.
Page 3
STEP 4
Attach Back Rail (G)
to Side Panel (C),
then flip Locks.
(See Figures 1 and 2)
Attach Back Uprights (F)
to unit.
Slide Back Panels (E)
into position.
Assembly Instructions 3/7
H
E
C
E
F
G
E
B
F
Attach Back Rail (H) to unit,
then flip Lock.
Attach Side Panel (B) to unit,
then flip Locks.
Head Cap Bolt (long)
Arrow label at front
J
Lock
Lock
Figure 1
Figure 2
STEP 5
Attach Base (J) to unit with
Head Cap Bolts (long),
then flip Locks.
(See Figure 3)
Note: Arrow label
indicates front of Base (J).
Figure 3
Page 4
Assembly Instructions 4/7
STEP 6
Attach Casters to unit with Head Cap Bolts
for Caster into pre-drilled holes
with Locking Casters at front.
(See Figure 4)
Note: Arrow label indicates front of unit.
Figure 4
Head Cap Bolt for Caster
Non-Locking Caster
Locking Caster
Wood Screw for Magnet
STEP 7
Attach Magnets to Front Rail (W)
by inserting Wood Screws for Magnet
into pre-drilled holes, then tighten.
(See Figure 5)
Arrow label at front
Magnet
W
Figure 5
Page 5
STEP 8
Assembly Instructions 5/7
W
Turn unit over to its’
upright position.
Attach Middle Panel (D)
and Front Rails (I), (W) to unit,
then flip Locks.
Insert Wood Screws (short)
into pre-drilled holes in unit,
then tighten.
Slide Towel Bar (L) into position.
L
D
I
I
Lock
Wood Screw (short)
V
Figure 6
STEP 9
Attach Leaf Supports (U) and (V) to unit
with Wood Screws for Leaf Support.
(See Figure 6)
U
Wood Screw for Leaf Support
Page 6
Drawer (T)
Assembly Instructions 6/7
Bottom
T1
T3
T2
Wood Screw (long)
Roller at back
STEP 11
Slide Drawer Bottom (T5) into groove.
Attach Drawer Bottom (T5) to
unit with Wood Screws (short).
STEP 10
Attach Drawer Front (T1) and Drawer
Back (T2) to Drawer Side (T3)
with Wood Screws (long).
T4
Attach Drawer Side (T4) to unit
with Wood Screws (long).
Wood Screw (short)
T5
Knob
Part List
T1.
Drawer Front
3 pcs.
T2.
Drawer Back
3 pcs.
Machine Screw
T3.
Drawer Side
3 pcs.
STEP 12
Attach Knob with Machine Screw.
T4.
Drawer Side
3 pcs.
T5.
Drawer Bottom
3 pcs.
Page 7
Assembly Instructions 7/7
STEP 13
Insert Adjustable Pins into side panel and middle panel at desired level.
(See Figure 7)
Place Shelves (S) into position.
Figure 7
Figure 8
Attach Doors (Q) and (R) by sliding door hinges into side panel hinges.
(See Figure 8)
Attach Knobs to Doors (Q) and (R) with Machine Screws.
(See Figure 9)
Q
R
S
S
Figure 9
Flat Head Screw
STEP 14
Attach Top (A) to unit
with Flat Head Screws, then flip Locks.
Lock
Adjustable Pin
A
Machine Screw
T
T
T
T
T
T
Knob
Slide Drawers (T) into position.
Page 8
CARE INSTRUCTIONS
NEVER
allow liquids to remain on furniture.
Absorption causes parts to warp
and split and finishes to delaminate.
Do not use power tools
above 8 volts to assemble.
PREVENT
CRACKING
Do not place
in direct sunlight.
PREVENT
FADING
NEVER
use glass cleaners on
finished furniture. Ammonia
chemically attacks the finish.
Do not write
directly on surface.
PREVENT
MARKING
Do not place hot
objects on surface.
PREVENT
FINISH DAMAGE
Do not use rubber
based placemats.
PREVENT
DISCOLORING
CLEAN
with a soft cloth moistened
in lukewarm soap and water.
Buff with a dry clean cloth.
Do not use commercial
waxes and polishes.
PREVENT
YELLOWING
Loading...