Assembly Instructions
adults are needed to execute these actions.
Page 1 of 10
Caution: You must read this before you proceed
Table
Caution: This Table is NOT a TOY
Keep your child/children at bay during the assembly process.
Whenever moving/lifting the Table and to prevent damage to the Table, two
Support Bar
First Leg Support
Bar
Second Leg
Support Bar
①
(M8x40mm)
②
(M8x25mm)
③
Screw
(M6x45mm)
④
(M6x50mm)
⑤
(M8.5/20*2mm)
⑥
Hardware
Parts List
Page 2 of 10
Label Picture Description QTY
A Side Table Top 2
B Center Table Top 1
C End Table Top 2
Table Top
D
4
E First Leg 2
F Second Leg 2
G
H
2
1
Label Picture Description QTY
Bolt
Bolt
Screw
Washer
Allen Key
17
17
5
33
29
2
Assembly Preparation
Page 3 of 10
Before Beginning Assembly:
x 17
x 17
x 5
x 33
x 29
Assembly Steps
Page 4 of 10
Overview
Side Table Top (A)
First Leg (E)
Center Table Top (B)
End Table Top (C)
Second Leg (F)
Second Leg Support Bar (H)
First Leg Support Bar (G)
This Table has multiple parts and may require up to 45 minutes to assemble. To give you
an overview of the Table parts, the above picture is to help you put the various parts into
perspective. Please read through the instructions below to familiarise yourself with the
parts and steps before assembly.
FRONT FACING
Step 1
Unpack and place all parts on a clean, non-marring surface.
Step 2
④
A
C
B
C
A
A
Page 5 of 10
Place Side Table Tops(A) and Center Table Top(B) facedown onto a clean, non-marring
surface.
Then align them as pictured.
Step 3
Place the End Table Tops(C) as pictured above.
Attach End Table Top(C) to Side Table Tops(A) using Screws(
pictured above.
6
4
) with Allen Key(⑥) as
Do not fully tighten the Screws.
⑥
Step 4
C
C
A
A
C
C
A
A
B
Page 6 of 10
6
3
5
Attach End Table Top(C) to Side Table Tops(A) using Screws(③), and Washers(⑤) with
Allen Key(
Do not fully tighten the Screws.
) as pictured above.
Step 5
6
1
Attach End Table Tops(C) to Side Table Tops(A) and Center Table Top(B) using
Bolts(①) with Allen Key(⑥) as pictured above.
Do not fully tighten the Bolts
④
⑥
Step 6
D
E
A
A
B
C
Page 7 of 10
6
4
Attach Table Support Bars(D) to Side Table Tops(A) and Center Table Top(B) using
Screws(
Do not fully tighten Screws.
) with Allen Key(⑥) as pictured above.
Step 7
6
2
5
Attach First Leg(E) to End Table Top(C) using Bolts(②), and Washers(⑤) with Allen
Key(
Repeat the same process with the remaining First Leg(E) and Second Legs(F).
) as shown in the picture above.
Do not fully tighten the Bolts.
Step 8
⑤
⑤
G
E
F
G
Page 8 of 10
F
E
6
Attach the First Leg Support Bar(G) to First Leg(E) and Second Leg(F) using Bolts(①),
and Washers(
Repeat the same process with the remaining First Leg Support Bar(G).
Do not fully tighten the Bolts.
) with Allen Key(⑥) as shown above.
1
5
Step 9
H
6
2
Attach Second Leg Support Bar(H) to First Leg Support Bar(G) using Bolts(②), and
Washers(
Do not fully tighten the Bolts.
) with Allen Key(⑥) as pictured above.
5
Step 10
Page 9 of 10
Stand the Table up, with assistance from your adult partner.
Exert pressure floorwards, onto the Table with both your hands.
This pressure will help the Legs and Table Top reach full alignment status.
Check for wobbles on a LEVEL surface.
If no wobbles are found proceed to tighten the Bolts and Screws in a sequential manner,
until evenly secured.
When tightening the Bolts and Screws tighten sequentially.
Do not tighten any Bolt or Screw fully and then move on towards the next one.
If there are still wobbles, loosen the Bolts and Screws and excute the same above
process.
If the Table is not Stable it could lead to damage to the product.
Your Table is ready for use.
This Table can only be used on a flat, level surface.
Page 10 of 10
Loading...