Page 1
IMPORTANT INSTRUCTIONS & OPERATING MANUAL
WARNING
CAUTION
Read and understand this entire owner’s manual, including all safety
information, before plugging in or using this product. Fail to do so could
result in fire, electric shock, or serious personal injury.
Keep this owner’s manual for future reference. If you sell or give away this
product,make sure this manual accompanies this product.
Page 2
CONTENTS
Important Safet
Preparation …………………………………………………………………………………………….….…... 5
Product Dimension …………………………………………………………………………………….……. 6
Assembly ……………………………………………………………………………………………….……... 7
Battery Information ………………………………………………………………………………………..… 7
Operation ……………………………………………………………………………………...………………. 8
Control Panel ………………………………………………………………………...………………… 9
Remote Control …………………………………………………………………………………...….. 10
Care and Maintenance ………………………………………………………………………………….…. 11
Schematic Diagram ………………………………………………………………………………………... 12
FAQ – Frequently Asked Questions ……………………………………………..……………………… 13
Troubleshooting Guide ………………
Limited Warranty …………………………………………………………………………………………… 15
Customer Service ………………………………………………………...………………………………… 15
y Information ……………………………………………………....................................... 3
………………………………………...…………………………..
14
Page 3
IMPORTANT SAFETY INFORMATION!
WARNING
Read all instructions before using this heater!
This heater is hot when in use. To avoid burns, DO NOT let bare skin touch hot surfaces. If
provided,use handles when moving this burning heater. Keep combustible materials, such as
furniture, pillows, bedding, papers, clothes, and curtains at least 3 feet (0.9m) from the front
of the heater, and keep them away from the sides and rear.
Extreme caution is necessary when any heater is used near children or invalids and
whenever the heater is left operating and unattended.
DO NOT operate any heater with a damaged cord or plug or after the heater malfunctions,
has been dropped or damaged in any manner. Discard heater, or return to authorized
service facility for examination and/or repair.
DO NOT run power cord under carpeting. DO NOT cover power cord with throw rugs,
runners, or similar coverings. DO NOT route power cord under furniture or appliances.
Arrange power cord away from traffic area, and where it will not be tripped over.
DO NOT insert or allow foreign objects to enter any ventilation or exhaust opening, as
this may cause electric shock or fire, or damage the heater.
To prevent a possible fire, DO NOT block air intakes or exhaust in any manner. This could
cause a fire. DO NOT use on soft surfaces, like a bed, where openings may be blocked up.
A heater has hot and arcing or sparking parts inside. DO NOT use it in areas where
gasoline, paint, or flammable liquids are used or stored.
Use this heater only as described in this manual. Any other usage not recommended by
the manufacturer may cause fire, electric shock, or injury to persons.
ALWAYS plug heaters directly into a wall outlet/receptacle. NEVER use with an
extension cord or relocatable power tap (outlet/power strip).
Connect to properly grounded outlets ONLY.
DO NOT place the heater near a bed because objects such as pillows or blankets can fall from
the bed and be ignited by the heater.
NEVER use this heater in bathrooms, laundry rooms, or any other location where the heater
could fall into a bathtub or pool, become damp, or touch the water.
AVOID FIRE! Regularly inspect all air vents to make sure they are free from dust, lint, or other
blockage. Unplug the unit and clean with a vacuum ONLY. DO NOT rinse or get wet.
NEVER permanently install in a recessed area of the wall. This may result in blocked air
flow, overheating, or fire.
WARNING: DO NOT DEPEND ON THE POWER SWITCH THE SOLE MEANS OF
DISCONNECTING POWER WHEN SERVICING OR MOVING THE HEATER. ALWAYS
UNPLUG THE POWER CORD.
WARNING: REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK---DO NOT USE THIS
HEATER WITH ANY SOLID STATE SPEED CONTROL DEVICES.
For residential use only! NOT for commercial use! Any commercial or public use of this
Page 4
heater voids all warranties, and could cause injury.
r
f
This product is not intended to be a primary heat source. It is for supplemental heat only.
INDOOR use only! NEVER use this heater outdoors! Doing so may result in electric shock!
Risk of electric shock! DO NOT OPEN! No user-serviceable parts inside!
NEVER modify this heater. Doing so could result in personal injury or property damage.
Modification of this fireplace completely voids all warranties.
ALWAYS turn this heater off before unplugging it from the outlet.
ALWAYS disconnect this unit from the power supply before performing any assembly or
cleaning, or before relocating the electric fireplace.
NEVER leave this heater unattended. ALWAYS unplug this heater when not in use.
ALWAYS store this heater in a dry location. NEVER use the fireplace if it has become wet.
ONLY use this heater on a 120V AC 15-Amp circuit. NEVER overload the circuit. If this heater
trips the circuit breaker, unplug all other appliances on the same circuit before the next use.
Avoid plugging other appliances into the same circuit as this heater.
NEVER plug this heater into an outlet that is old, cracked, or has any loose wires or
connections. Plugging this heater into a faulty outlet could result in electric arcing within the
outlet that could cause the outlet to overheat or catch fire.
ALWAYS check your heater cord and plug connections with each use!
i) MAKE
cause the outlet to overheat
ii)
Heaters draw more current than small appliances. Overheating may occur even if it has not
occurred with the use of other applia
iii) During use check frequently to see if the plug outlet or faceplate is HOT!
iv) If the outlet or faceplate is HOT, discontinue use immediately and have a qualified
electrician inspect and/or replace the faulty outlets.
This heater has a polarized plug (one blade is wide
than the other). As a safety feature to reduce the risk o
electrical shock, this plug is intended to fit in a polarized
outlet only one way. If the plug does not fit fully in the
outlet, reverse the plug. If it still does not fit, contact a
qualified electrician. Do not attempt to defeat this safety
feature.
SURE the plug fits tight in the outlet! Faulty wall outlet connections or loose plugs can
.
nces.
SAVE THESE INSTRUCTIONS!
Page 5
PREPARATION
DO
NOT use this Electric Fireplace if any part has been under water. Immediately call a
qualified service technician to inspect and to replace any part of the electrical system if
necessary. Keep plastic wrapping away from children.
Unpacking the Electric Fireplace. Remove all parts and hardware from the carton and place them on a
clean, soft, dry surface. Check the parts list to make sure nothing is missing. Dispose of packaging
materials properly. Please recycle whenever possible. Keep the original packaging for future transport
and/or storage.
Firebox X 1 pc
Remote Handset × cp 1
Owner’s Manual ×1 pc
Page 6
PRODUCT DIMENSIONS
Fireplace Insert
IW
Width
（
W）
ID
Height
（H）
IH
Fireplace Insert Size
Advise mantel opening size
Depth
（D）
（
Width
OW）
Insert Width
Height
（OH）
Fireplace Mantel
Units:inch
Insert Height
Insert Depth
（IW） （IH） （ID）
36.60
39.56
26.03 7.70
26.02
7.70
Units:mm
1016 694 224.6
1091
Width
W）
（
693.9
Height
（H）
22
4.6
Depth
（D）
940-1000 675-685
1025-1061 675-685
Advise mantel opening size
Width
OW）
（
Height
（OH）
40.0 27.32 8.84 37-39.40 26.6-26.95
42.9 27.32 8.84 40.35-41.8 26.6-26.95
Units:inch
Page 7
ASSEMBLY
ALWAYS unplug this fireplace heater before assembly or cleaning, or before relocating.
Failure to do so could result in electric shock, fire, or personal injury.
KEEP drapery and other furnishings at least 3ft /0.9m from the front and sides of the
electric fireplace.
AFTER installation, ensure that there is ≥0.004 ㎡
outside of fireplace mantel.
Your
new electric fireplace may be installed virtually anywhere in your home. However, when choosing a
location ensure that the general instructions are followed. For best results, install out of direct sunlight.
Power supply service must be either completed or placed within the electric fireplace prior to finishing to
avoid reconstruction.
ventilation area between inside and
When moving the insert into mantel, Do not let bottom of insert touch the mantel to avoid the scratch.
BATTERY REPLACEMENT
NOTE: The remote control not include the batteries.
NOTE: Do not mix old and new batteries.
Do not mix alkaine,standard(carbon zinc),or rechargeable(nicad,nimh,ect.)batteries.
Page 8
OPERATION
Read and understand this entire owner’s manual, including all safety information, before
plugging in or using this product. Fail to do so could result in e lectric shock, fire,
serious injury, or death.
Power
Make sure the Power Switch, located on the control panel, is in the OFF position. Plug the power cord
into a 110~120 Volt 15 Amp outlet (see IMPORTANT SAFETY INFORMATION on Pages 3 and 4).
Make sure the outlet is in good condition and that the plug is not loose. NEVER exceed the maximum
amperage for the circuit. DO NOT plug other appliances into the same circuit.
Temperature Limiting Control
This heater is equipped with a Temperature Limiting Control. Should the heater reach an unsafe
temperature, the heater will automatically turn OFF. To reset:
1. Unplug the power cord from the outlet.
2. Turn the Power Switch on the CONTROL PANEL to OFF. Wait at least 5 minutes.
3. Inspect the fireplace to make sure no vents are blocked, or clogged with dust or lint. If they are,
use a
vacuum to clean the
4. Wi
5. If
th the Power Switch in the OFF position, plug the power cord back into the
it switches off again, UNPLUG THE HEATER RIGHT AWAY! Have the outlets, wiring,
breaker b
ox inspected by a professional. Make necessary repairs before using the heater.
vent areas.
outlet.
and
Heater Rating
Maximum heat output: 1500W (5000BTU); Maximum heating area: 400 square feet.
Operation
Review the IMPORTANT SAFETY INFORMATION on Pages 3 and 4 before operating.
When the heater is first turned on, a slight odor may be present. This is normal
NOTICE:
and should not occur again unless the heater is not used for a long period of
time.
Open a door on the top right side
for operation all functions
Page 9
Control Panel
Located on the right and top side panel of the fireplace.
Turn on the main power supply. A long “beep” sound will be heard
when the switch is turned on On Position “I”.
POWER
SWITCH
Note: The remote control will lost the memory for function settings
when the switch is turned on Off Position “0”.
The flame will be cycled F1 – F2 – F3 – F4 – F5-Flame Off.
NOITCNUF EMAN NOTTUB
FLAME
HEATER
Log Speaker
F1 is the less flame,F5 is the biggest flame.
The heater will be cycled Low – High – Heater Off. You will see the
screen light illuminates on right of the flame board.The indicator light
goes out within 5s.
Low: (LO)
High: (HI)
Note:
1. Fireplace can be used without heater
2. Whether the heating is working depends on whether the settled
temperature by thermostat is higher than the environmen
temperature.
3. The
The log speaker can make the real log burning effect.
Press first time to turn on the log speaker,
Press second time to turn off the log speaker.
Fan works anterior to the heater about 10s, and turns off la
than the heater
about 10s.
.
ter
t
TOP LIGHT
TIMER
There are three colors for option.
Press the first time for orange color,
Press the second time for the blue color,
Press the third time for the purple color.
This fireplace is equipped with a timer ranging from 1hr to 9hrs(1H,2H
...9H,Off shown on the LCD display),touch the button once for every
1hr increase.
Page 10
Remote Control
Control panel Power Switch must be ON to use remote control.
NOTICE:
Aim the remote control at the remote receiver. Make sure you hear a beep each
time you press the button! If not, the fireplace will not respond to the signal.
NOTICE:
Operation for all functions are same as the buttons on the fireplace.
Log Speaker
Timer
Top light
Power ON/OFF
Heater setting
Flame Flame
Page 11
CARE AND MAINTENANCE
ALWAYS tu
cleaning, performing maintenance, or moving this fireplace. Failure to do so could result in
electric shock, fire, or personal injury.
rn the heater OFF and unplug the power cord from the outlet before
Cleaning
VER immerse in water or spray with water. Doing so could result in electric shock,
NE
fire, or personal injury.
Metal:
Buff using a soft cloth, slightly dampened with a citrus oil-based product.
DO NOT use brass polish or household cleaners as these products will damage the metal trim.
Glass:
Use a good quality glass cleaner and dry thoroughly with a paper towel or lint-free cloth.
NEVER use abrasive cleansers, liquid sprays, or any cleaner that could scratch the surface.
Plastic:
Wipe gently with a slightly damp cloth and a mild solution of dish soap and warm water.
NEVER use abrasive cleansers, liquid sprays, or any cleaner that could scratch the surface.
Vents:
Use a vacuum or duster to remove dust and dirt from the heater and vent areas.
Clean the exterior of the fireplace with a slightly damp cloth or duster.
Maintenance
Risk of
ALWAYS turn the heater OFF and unplug the power cord from the outlet before
cleaning, performing maintenance, or moving this fireplace. Failure to do so could result in
electric shock, fire, or personal injury.
Electrical and Moving Parts:
The fan motors are lubricated at the factory and will not require lubrication.
Electrical components are integrated in the fireplace and are not serviceable by the consumer.
Storage:
Store heater in a clean dry place when not in use.
Replacement parts:
Use only replacement parts supplied by the manufacturer. Use of any other parts, or modifying
the fireplace in any way, will void all warranties.
No internal parts are replaceable or serviceable.
WARNING! No other servicing should be performed by the consumer. Do not attempt to
service the unit by yourself.
electric shock! DO NOT OPEN! No user-serviceable parts inside!
Page 12
SCHEMATIC DIAGRAM
Log speaker
Temperature receiver
IN A C
N
AC L
HOT1 HOT2
FAN
LED+
SWING
LED-
Thermal cut device
Power switch
Wind motor
Heating element
L
N
M M
Flame motor
LED light
Page 13
LIMITED WARRANTY
This warrants to the original purchaser that this product is free from defects in material and workmanship
as of the date of purchas e and that it will, un der nor mal use and proper care, remain one year
from the date of purchase. Missing or initially defective parts will be replaced free of charge during the
period of this limited warranty. If parts are unavailable, comparable replacement of refund will be given.
The original dated sales receipt is required for all warranty claims. This warranty does not cover
damage which has occurred during transport from the point of purchase to the consumer’s home. This
warranty does not cover glass, light bu
with the manufacture of the product.
This product is for residential use only. Any and all commercial use of this product voids all
warranties, and absolves the manufacturer from all liability.
Read and understand all assembly and operating instructions, and all safety information and warnings,
before use. The following will void this warranty: Damage caused by tampering, modifying , or
altering the fireplace insert in any manner; Damage due to incorrect assembly, improper care, misuse, or
abuse; Damage from being used with the wrong power source; Water damage; Damage caused from
this insert being used outdoors; Damage caus ed by using for excessive periods of time; Damage
caused by the insert being used in a commercial application; Damage from use as a primary heat
source;Other misuse or abuse not specifically listed herein.
This product is not intended to be used as a primary heat source. It is for supplemental heating
purposes only.
lbs, batteries, transportation, labor, or other issues not associated
Loading...