Caution: You must read this before you proceed.
Dining Chair
Label Picture Description QTY
A Chair Back 1
B Seat 1
C Front Leg 2
D Left Back Leg 1
E Right Back Leg 1
1 of 8
Label Picture Description QTY
① Bolt (M8X60) 3
② Bolt (M8X35) 7
③ Washer M8*2.1MM 10
④
⑤
⑥
⑦
⑧
⑨
Before Beginning Assembly:
Washer M8*1.6MM 3
Spring Washer 13
Allen Key 1
Screw Arbor 4
Spanner 1
Nut 4
Unpack
all the
parts for
a clear
overview.
2 of 8
Step 1
OVERIVEW
Seat (B)
Chair Back (A)
Front Leg (C)
Right Back Leg (E)
FRONT FACING
This Dining Chair has multiple parts and may require up to 30 minutes to assemble.
To give you an overview of the Chair parts, the above picture is to help you put the
various parts into perspective. Please read through the instructions below to
familiarise yourself with the parts and steps before assembly.
Carefully remove the Seat Base Cover from the Seat(B).
Take out the Legs and Hardware.
3 of 8
Step 3
Step 2
Step 2.1 Screw the Screw Arbor(
) into Chair Back(A) by turning clockwise as
shown.
A
⑦
Step 2.1
Step 2.2
A
B
⑦
A
B
Step 2.2 After Step 2.1, Push down the Seat(B) using a good amount of pressure to
make the Seat(B) connect with Chairback(A) thourgh the Screw Arbor(⑦) of Chair
Back(A) as shown.
⑦
Connect Chair Back(A) with Seat(B) using Screw Arbor(⑦) and tightening tighten by
turning theScrew Arbor(⑦) clockwise, as shown.
4 of 8
Step 4
Step 5
Align the mounting positions on the right ,middle and left of Chair Back(A) and
E
D
A
B
①
⑥
⑤
④
Seat(B); using the Spring Washers(⑤) , Washers(③), Nut(⑨) mounted on Screw
Arbor(⑦) with Spanner(⑧).
Attach Back Leg(D) to the bottom of the Chair Back(A) using Bolt(①), Spring
Washer(⑤) and Washer(④) with Allen Key(⑥).
Do not fully tighten the Bolts.
Repeat the same process with Back Leg(E).
5 of 8
Step 7
Align the mounting positions of Front Legs(C) to Seat(B), then attach using Bolts(②),
Step 6
A
B
C
C
E
②
③
⑤
⑥
D
Place Dining Chair on flat, level surface.
Spring Washers(⑤) and Washers(③) with Allen Key(⑥).
Do not fully tighten the Bolts.
Stand the Chair up and place on flat, level surface.
Carefully and gently sit onto the Chair. This will help properly align all parts at all
joints and remove any gaps.
Carefully get off the Chair and gently turn it over.
Tighten all Bolts at all joints. When tightening the Bolts, tighen in a sequential
manner
6 of 8
Smooth down the Seat Base Cover your hand along the Magic Tape on all four sides
Step 8
Step 9
A
B
C
C
D
E
at the edge of the Seat.
Make sure all parts are connected and securely locked into position.
Your Dining Chair is ready for use.
This Dining Chair can only be used on a flat, level surface.
7 of 8
8 of 8
Loading...