Page 1
Page 1 of 11
Page 2
Page 2 of 11
Page 3
Page 3 of 11
Page 4
Page 4 of 11
Page 5
CAM LOCK FASTENER ASSEMBLY INSTRUCTIONS
Page 5 of 11
Page 6
END TABLE
ASSEMBLY INSTRUCTIONS
please keep for future reference PARTS LIST
HARDWARE LIST
1
14PCS
2
14PCS
3
8PCS
4
1PC
5
4PCS
6
4PCS
7 8
DIMENSIONS : 15.7"(W)*19.7"(D)*19.3"(H)
Page 6 of 11
9 10
11
4PCS1SET
1PC
A
1PC
B
D
F
4SETS
1PCC
1PC
D
1PC
E
1PC
F
4PCS
1PC
H
1PC
J
1PC
1PC
I
K
1PC
L
G
8PCS
1PC
M
C
D
E
H
2.2" 1.0"
0.5" 0.9" 0.7"
Page 7
ASSEMBLY INSTRUCTIONS
Identifying Drawer's Rails (a.k.a. Runners, Glides, Slides or Guides)
An assembly of ONE drawer requires a set of 4 different rails: right panel rail, left panel rail, right
drawer rail and left drawer rail. To identify which rail belongs to which part, please read completely
first before assembling.
To Determine Right/Left Panel Rail: Place the panel rail flat on its back with the roller position on
the left hand side. If there are two holes above the roller and the other end is slightly downward angle
then it is the LEFT PANEL RAIL. If there are two holes below the roller and the other end is slightly
upward angle, then it is the RIGHT PANEL RAIL. The right and left panel rails are mirror image of
each other. If needed, label or separate each rail for easy identification.
To Determine Right/Left Drawer Rail: Place the drawer rail with the round and oval holes resting
flat on the surface with its roller on the right hand side. If the roller is facing the top, then it is the
LEFT DRAWER RAIL and if the roller is facing the bottom, then it is the RIGHT DRAWER RAIL. The
right and left drawer rails are mirror image of each other. If needed, label or separate each rail for
easy identification.
Mounting the Panel Rail: The panel rail is constructed to be mounted flat. Make sure the roller is
position on the front of the panel and the screw holes are aligned with the pre-drilled holes of the
panel.
Mounting the Drawer Rail: The drawer rail is constructed to be mounted on the side of the drawer .
Make sure the roller is position on the SIDE REAR of the drawer and the screw holes are aligned
with the pre-drilled holes on the side of the drawer .
6
STEP : 1
Hardware 1 x 2 pcs
Hardware 2 x 2 pcs
Hardware 3 x 2 pcs
Hardware 6 x 4 pcs
Hardware 7 x 2 pcs drawer rails
Hardware 8 x 4 pcs
Hardware 9 x 1 set
9
8
I
7
2
3
3
Dowel hole
H
Right Drawer Rail
Front View
Side View
6
H
7
8
Page 7 of 11
Page 8
ASSEMBLY INSTRUCTIONS
STEP : 2
Hardware 1 x 12 pcs
Hardware 3 x 6 pcs
Hardware 7 x 2 pcs panel rails
Hardware 8 x 4 pcs
B
3
3
F
G
Dowel hole
3
X4
7
D
D
Right Panel Rail
Page 8 of 11
Page 9
STEP : 3
Page 9 of 11
Hardware 2 x 2 pcs
finish
ASSEMBLY INSTRUCTIONS
finish
F
2
2
Dowel hole
STEP : 4
Hardware 2 x 2 pcs
Hardware 5 x 4 pcs
D
2
F
D
2
B
5
Page 10
Page 10 of 11
STEP : 5
Hardware 2 x 4 pcs
ASSEMBLY INSTRUCTIONS
STEP : 6
Hardware 2 x 4 pcs
Page 11
Page 11 of 11
STEP : 7
Hardware 10 x 4 pcs
Hardware 11 x 4 sets
ASSEMBLY INSTRUCTIONS
STEP : 8
Make sure the unit is rested on a flat
surface and does not feel loose or
wobbly. If it does, double check all
bolts/screws are secured and properly
tightened.
ASSEMBLY IS COMPLETED
Loading...