Page 1
Caution :You must read this before you proceed
CORNER
Label Picture Description QTY
A Seat Frame 1
B
B1
C Back Cushion 2
D Leg 4
Long Backrest
Labelled as B
Short Backrest
Labelled as B1
1
1
1 of 7
Page 2
Label Picture Description QTY
①
②
③
④
⑤
⑥
Before Beginning Assembly:
Washer Ring 7
Allen key 1
Bolt M8*20mm 2
Spring Washer 2
Flat Washer 2
Connecting Piece 1
2 of 7
Page 3
OVERVIEW
Back Cushion(C)
Short Backrest（B1)
Seat Frame (A)
Back Cushion(C)
Long Backrest (B)
Leg (D)
Leg (D)
Leg (D)
FRONT FACING
This CORNER has multiple parts and may require up to some 30 minutes to
assemble. To give you an overview of the CORNER parts, the above picture is
to help you put the various parts into perspective. Please read through the
instructions below to familiarise yourself with the parts and steps before
assembly.
Step 1
C
A
C
B
B1
Position the Seat Frame (A) on its back,as shown.
Unzip to open pouch and remove the 4 wooden legs, Back Cushion(C), close
the pouch.
3 of 7
Page 4
Step 2
D
D
A
WasherRing(①)
D
Install the Legs(D) into the bottom of the Seat Frame (A) by placing a Washer
Ring(①) onto the threaded stem of the Legs.
And then insert the threaded stem into the threaded mounting position at each
Corner of the Bottom of the Seat Frame (A).
Tighten by turning the Legs clockwise.
Note: The use of Washer Ring(①) are OPTIONAL and are especially useful to
help alleviate slight wobbles.
Some Legs may need more than one Gasket whilst some Legs may not need
any.
Position CORNER chair right side up and test for stability on a Level Surface.
Add or remove Washer Ring(①) where needed to achieve stability.
Step 3
A
Cover the bottom of the Seat Frame (A) with the non-woven fabric.
Smooth down the Magic Tape on all four sides of the Seat by hand.
4 of 7
Page 5
Step 4
Short Backrest B1
Seat
Frame (A)
Long Backrest B
Position Corner chair right side up.
Align the mounting positions on the Seat Frame (A) and the Long Backrest(B) .
Insert the Long Backrest (B) into the Seat Frame (A) as shown in above
picture.
Repeat the same step to install the Short Backrest(B1).
Step 5
Back Cushion (C)
Put the Back Cushion (C) on the CORNER chair.
Step 6
Back Cushion (C)
Seat Frame (A)
Your CORNER chair is ready for use.
Your CORNER chair can only be used on a flat, level surface.
5 of 7
Page 6
If you already purchased 2 or more than 2 products, Please read on
Step 1
⑤
③
④
⑥
Attach the Connecting Piece(⑥) to Seat Frame (A) using Bolts(③), Spring Washers(④),
and Flat Washer (⑤) with Allen Key(②) as shown in the picture.
②
Step 2
⑥
⑥
⑥
⑥
Connecting the two sofas by using the pre-fixed Connecting Piece (⑥) as
shown in the picture.
Step 3
Step3.3
Step3.4
Step3.1 Step3.2
Note: This is optional step in case we want to connect all sofas in a set
together and to match the environment of your home.
6 of 7
Page 7
7 of 7
Loading...