Page 1
Furniture
of
A
merica
ODEL #
M
CM3615T
uestions?
Q
G
IVE US A CALL: 1-888-980-5122
MON – FRI 8:30AM – 5:30PM (PST)
OOLS REQUIRED
T
hilips
P
-60
Screwdriver
Not Included)
(
1 / 7
2 - Persons
Recommended
SSEMBLY RATING
A
ASY
E
T
he Assembly Rating is a
5-point system showing the
level of effort needed to
assemble a specific product.
IFFICULT
D
Page 2
PRE ASS EM BLY
INTRODUCTION
We understand building ready-to-assemble furniture can be a challenging
experience for some. To help avoid confusion, we have provided some helpful
tips that may speed up the process.
Teamwor k
ALWAYS have at least two people
to help with transporting and
assembling the product to avoid
potential injury and/or damage.
Suitable Location
Assembling near the area of the
intended location is highly
recommended.
Sufficient Space
Make sure you have enough
space to move around during the
assembly.
Avoid Scratches
Use cardboard, blankets or a
carpeted area while assembling
furniture to prevent scratches.
3 / 7
Flat Surface
Make sure the furniture rests on
a flat and level surface with each
leg evenly touching the floor.
Page 3
4 / 7
Page 4
TABLE
CM3615T-60
Please keep instructions for
future reference.
Check the quantity and
irregularity of parts and
hardware before you start.
PARTS
#1 2pcs
Leg Stand
#4 1pc
Leg Stand Support
#2 1pc
Table Top
HARDWARE
#3 2pcs
Apron
#A
20pcs
Bolt 1/4”x5/8”
#B
10pcs
Screw
5 / 7
#C
1pc
Allen Wrench
Page 5
1
#1 x 2pcs
Part
#3 x 2pcs
Part
#4 x1pc
Part
Hardware
#A x
20pcs
I. Align the 2 aprons (#3) with the
brackets of the leg stand (#1).
II. For each bracket of the leg stand
(#1), insert 2 bolts (#A) through the
bottom of the bracket and 2 bolts
(#A) through the side of the bracket
using the Allen wrench (#C) to
secure them wit h the apron (#3).
III. Align one end of the leg stand
support (#4) with the pre-drilled
holes on the center of the same leg
stand (#1).
IV. Insert 2 bolts (#A) through the
bracket of the leg stand support (#4)
using the Allen wrench (#C) to
secure them with the leg stand (#1).
V. Repeat the process above to
assemble the other leg stand (#1)
onto the other ends of the 2 aprons
(#3) and the leg stand support (#4).
2
#2 x1pc
Part
#B
Hardware
I. With the help of another person,
carefully place the table top (#2)
facing down on a protected surface.
II. Align the assembled leg stands (#1)
WRthe table WRS
tDEOHWRSKDVQRSUHGULOOHGKROHV
III Secure 6 screws (#B) through the 2
leg stands (#1) and 4 screws (#B)
through the 2 aprons (#3) using a
Phillips screwdriver to secure them
with the table top (#2).
IV. Carefully place the completed table
upright. Make sure the table is rested
on a flat surface and does not feel
loose or wobbly. If it does, double
check that the bolts/screws are
secured and properly tightened.
x 10pcs
6 / 7
Page 6
3
7 / 7
Loading...