Page 1
Page 2
ASSEMBLY INSTRUCTIONS
STEP 1 :
Attached and tighten the Headboard Leg L/R ( C
to the Headboard ( A ).Insert Spring Washer ( 5)
Flat Washer ( 6 ),
use JCBC Bolt ( 3)
to fix with
Allen Key ( 7 ).
)
STEP 3 :
Attached and tighten the Triangle
Support Panel ( D ) to the Headboard
and fix the Panhead Screw ( 2 ) using
Screw
Driver.(
Not Included)
STEP 2 : Attached and ti
NOTE : MU
to the Headboard ( A ).Insert
Flat Washer ( 6 ),use
Allen Key ( 7 ).
ST TIGH
TEN SCREWS PERIODCALL Y
ghten the Headboard Leg L/R ( C
JCB
Spring Was
C Bolt
( 4)
her
(
to
fix
5)
with
WITH USE SCREW WILL BECOME LOOSE CHECK TIGHTNESS
A
)
PAG
OF'1\.
LL SCREW EVERY 6-8 WEEKS
.
E2 OF7
Page 3
ASSEMBLY INSTRUCTIONS
STEP 4 : Attach Headboard Back Support ( L ) and ( 0 ) follow the
picture.Fix the CSK Screw ( 1)
(
Not Included
)
using a Screw Driver.
STEP 5 : Attach the Side Rail ( H ) to the Headboard Leg ( C ) and
Footboard ( B ).
( 13
),use JC
Insert Spring Washer ( 12),
BC Bolt (
10 )
to fix with Allen Key ( 15
Flat Washer
).
x8
NOTE :
MUST TIGHTEN
S
CREWS PERIODCALLY W
ITH USE SCREW WILL BEC
OME
LOO
SE CHECK TIGHTNESS O
F'AL
L SCREW
EVE
RY 6-8 WEEKS.
PAG
E3
OF7
Page 4
ASSEMBLY INSTRUCTIONS
.
STEP 6 :
Attach the Footboard Drawer Frame ( J)
the Side Rail (H).lnsert Spring Washer
Flat Washer ( 13) &
with
Allen Key ( 15 ).
JCBC Bolt ( 10)
to fix
to
( 12
),
STEP 8 :
Attach the Drawer Support Rail ( E ) to the Footboard
Drawer Frame
Washer ( 13
( J ).Insert Spring Washer ( 12
) & JCBC Bolt ( 10)
to fix with Allen Key
),Flat
( 15
).
STEP 7:
Attach Support Leg
Drawer Frame ( J
Flat Wa
with Allen Key
NOTE: MUST TIGHT
).Insert Spring Washer ( 12
sher ( 13) &
( 15
EN
SCREWS PERIODCA
3 ( G)
to the Footboard
JCBC Bolt ( 10) to fix
).
LLY
WITH USE S
STEP 9 : Attach the Drawer Support Rail ( E
),
to the Footboard
( B ) using CSK
Screw ( 8 ) and tighten with Screw
Driver.( Not Included
CRE
W WILL BECOME LOOSE CHECK TIGHTNESS OF ALL SCREW EVERY 6-8 WEE
)
)
KS.
PAGE40F7
Page 5
-
,
ASSEMBLY INSTRUCTIONS
STEP 10:
Attach Support Leg 2 ( F)
Drawer Support Rail ( M ).Use JCBC
Bolt (
11
) to fix with Allen Key ( 15
to the
).
xl
Step 12 : Attach Bed Slat ( I )
Use JCBC Bolt ( 11 ) to fix with Allen Key
( Loosen and tighten the Adjuster to stability
&
(
P ) to the Bed Slat Support ( N )
(
15
of~
r1
.
).
I
STEP 11 : Attach
Si
de Rail ( H ) using Csk Screw ( 8 ) and
tighten with Screw Dr
NOTE: MUST
TIGHTEN
Drawer S
SCREWS PERIODCALLY WITH USE SCREW WILL BEC
upport
iver.( Not
Rail ( M ) to the
Included)
STEP
OME LOOSE CHECK TIGHTNESS OF ALL SCREW EVERY 6-8 WEEKS
13:
Attach Z-Bracket ( 14) to th
Support ( N) and Support Leg 2 ( F ).
Panhead Screw ( 9 ) and tighten with screw
e Bed Slat
Use
driver
.
(not included)
PAGES
OF7
Page 6
ASSEMBLY INSTRUCTIONS
STEP 14:
STEP 15 : Attach
Attach
S
upport
Support Rail -2 ( E ).
Drawer-2 ( R) on Drawer
Rail -1 ( M
Drawer-1
).
(
Q
)
on Drawer
STEP 16:
Install th
drawer
usin
g Screw
e Handle ( 16) in fr
(R)
.Tighten the
Driver.
Handle
( Not In
ont of
Screw ( 18)
cluded)
x4
NOTE: MUST TfGHT
EN
SCRE
WS
PERIOD
ALIGNEMENT
Adjus
t the
alignment
CALLY WITH USE SCRE
STEP
17: In
stall th
adjuster for
of
drawer box
W WILL BECOME LOOSE CHECK TIGHTNESS OF ALL SCREW EVERY 6-8 WEEKS
drawer (Q).Tighten the Ha
usi
e Handle ( 16)
ng Screw Dri
in front of
ver.( Not Included )
ndle Screw ( 17)
.
PA
GE 6 OF7 ยท
Page 7
ASSEMBLY INSTRUCTIONS
STEP 18 : Push the Side Ra
CSK Screw (
8)
( Make sure follow the center Marking Line as shown )
xl
Diagram 1:
il ( H ) with Bed Slat ( I ) and tighten with
by using Screw
O
Driver.( Not Included)
WARNING!!! USE LONG
CHIPBOARD
(M4
SCREW
x32mm
)
STEP 20:
Attach Concealed Panel Sla
t (
K) at
the Upper Bed Sla
( I ) using Panhead Screw ( 9 ) and tighten with Sc
D
river. ( Not Included)
Diagram
2:
WARNING!!! USE SHO
CHIPBOARD SCREW
(M3.
5 x 20mm)
t
rew
RT
NOTE: MUST TIGHTEN SCREWS PERlODCALLY WITH USE SC
REW WILL
BECOME
LOO
SE
CHECK TIGHTNESS OF ALL SC
REW EV
ERY 6-8 WEEKS.
PAG
E 7 OF
7
Loading...