Red Barrel Studio ADML8213 Installation & Assembly

INSTALLATION AND SAFETY INSTRUCTIONS
FOR YOUR SAFETY WARNING: BE SURE THE ELECTRICITY TO THE WIRES
YOU ARE WORKING ON IS SHUT OFF; EITHER THE FUSE IS REMOVED OR THE CIRCUIT BREAKER IS SHUT OFF.
GENERAL You don’t need special tools to install this fixture. Be sure to follow the steps in the order given. Under no circumstances should a fixture be hung on house electrical wires, nor should a swag type fixture be installed on a ceiling, which contains a radiant type heating system. Read instructions carefully. If you are unclear as to how to proceed, consult a qualified electrician. NOTE: Proper wiring is essential for the safe operation of this fixture.
FIXTURE ASSEMBLY
Carefully remove the fixture from the carton and check that all parts are included as shown in figure. Be careful not to misplace any of the screws or parts, which are needed to install this fixture. NOTE: T his fixture can be mounted in two ways: SEMI FLUSH OR PENDANT. STEP 1: Hook the hook of arm (I) to the hook (H). Hook the
other hook of arm (I) to the hook (J) of frame.
PENDANT INSTALLATION CAUTION: Please buy one hardware bag for pendant
installation (not provide) and assembly according to ASSEMBLY INSTRUCTION SHEET OF PART BAG.
SEMI FLUSH INSTALLATION IMPORTANT: Do not attach fixture directly to outlet box. STEP 1: Secure the mounting bar (A) to outlet box with the
outlet box screws (B).
STEP 2: Thread the nut (D) onto the nipple (E). Insert the lock
washer (C) and thread the nipple (E) into the mounting bar (A), then secure with the nut (D).
GROUNDING INSTRUCTIONS STEP 1: Insert the green grounding screw into the hole with two
raised dimples on the mounting bar. Wrap the ground wire from the fixture (if supplied) around the green grounding screw, then connect it to ground wire from the outlet box (if not fixed on the outlet box) using a wire connector (not supplied). If ground wire from the fixture is not supplied, wrap the ground wire (if not fixed on the outlet box) from the outlet box around the green grounding screw and tighten it.
NEVER CONNECT GROUND WIRE TO BLACK OR WHITE
POWER SUPPLY WIRES.
STEP 2: Take note of the color of the wire(s) on your fixture.
Identify which group your fixture wire(s) falls into and connect the wires according to the directions below:
GROUP A: Connect to Black House Wire BLACK WHITE *PARALLEL WIRE (round & smooth) WHITE OR GREY WITH TRACER BROWN GOLD OR BLACK WITHOUT TRACER
*NOTE: When parallel wire (SPT-I & SPT-2) is used, the tracer wire is square shaped or ridged and the less tracer wire is round in shape or smooth (seen best when viewed from wire end.)
STEP 3: Take your fixture wire(s) from group A and place
evenly against the black wire from the outlet box. Do NOT twist wires together before using wire connectors.
STEP 4: Fit a wire connector over the wires and screw the
connector clockwise until you feel firmness.
GROUP B: Connect to White House Wire
*PARALLEL WIRE (square & ridged) WHITE OR GREY WITHOUT TRACER BROWN, GOLD OR BLACK WITH TRACER
STEP 5: Try gently to pull the connector off the wires. If you
can pull the connector off, carefully re-do steps 3 and 4 as above, and check again for a firm connection.
STEP 6: Connect the fixture wire from group B to the white
wire from the outlet box in the same manner. Make sure no bare wires can be seen outside wire connectors.
FINAL ASSEMBLY STEP 1: (FOR SEMI FLUSH) After wires are connected, tuck
them carefully inside outlet box, then secure the canopy (F) allowing the nipple (E) to protrude through the holes in the canopy (F) and secure with the ball nut (G).
STEP 2: Install light bulbs.(Please do not exceed the maximum
capacity recommended on the socket.)
STEP 3: Slide the glass (L) and the washer (M) onto the nipple
(K) and secure with the cap (N).
CLEANING
To clean, wipe fixture with a soft cloth. Clean glass with a mild soap. Do not use abrasive materials such as scouring pads or powders, steel wool or abrasive paper.
Line art shown may not exactly match the fixtu re enclosed. However, the installations do apply to this fixture.
Loading...