Page 1
Monocrystalline
Folding Solar Panels
SMP1090
SMP1120
SMP1150
Page 2
MONOCRYSTALLINE FOLDING SOLAR PANELS
REDARC folding solar panels are designed to provide a solar charging solution for your house or auxiliary
battery. They feature the folding panel, Y-Adaptors, 5m of cabling with 50Amp Anderson Plug, tent peg
and a strong nylon carry bag. The panel itself features reinforced aluminum legs, top quality hinges and
latches and a fold-away handle.
A solar regulator is not included and is required for connection to a battery. The SMP Panel is a 12Volt
solar panel suitable for 12Volt battery systems only.
WARNING & SAFETY INSTRUCTIONS
This appliance is not intended for use by persons (including children) with reduced physical, sensory
or mental capabilities, or lack of experience and knowledge, unless they are supervised or have been
instructed on how to use the appliance by a person responsible for their safety. Children should be
supervised to ensure that they do not play with the appliance.
Do NOT use the Solar Panel to charge non-rechargeable batteries. Doing so may result in harm to
the user and/or damage to the Regulator and/or Solar Panel. Only use the Solar Panel for charging
through a sutiable regulator.
All lead acid batteries produce harmful, explosive gases. The Battery should be mounted in a well
ventilated area, as far as possible from any ignition sources. Do NOT smoke when in the vicinity of
the battery under charge.
Battery acid is a harmful substance. Care should be taken when working with lead acid batteries,
if the acid comes into contact with your eyes or skin, immediately wash the affected area with cold
running water and seek medical assistance. Eye protection and gloves should be worn when handling
lead acid batteries.
The Solar Panel will achieve best results when proper battery maintenance is regularly performed.
This includes but is not limited to checking water and specific gravity levels of the battery.
Warning! Check the manufacturers data for your battery and ensure that the ‘Absorption’ voltage
of the regulator you select does not exceed the manufacturers recommended maximum charging
voltage. If the ‘Absorption’ voltage for your battery type is too high, please select another charging
profile or regulator (regulator not included).
SAL.FOR.Instruction Manual Monocrystalline Folding Solar Panels – DOC926 – Version 1
1
Page 3
CONTENTS
The Monocrystalline Folding Solar Panel 1
Supplied Parts 2
The Folding Solar Module 3
90watt Mono Folding Solar Panel 4
Specifications 4
120watt Mono Folding Solar Panel 5
Specifications 5
150watt Mono Folding Solar Panel 6
Specifications 6
System Installation 7
System Wiring 7
Installation Notes 7
Standard Setup (90W and 120W) 8
Standard Setup (150W) 8
SUPPLIED PARTS
1 Mono Folding Solar Panel
2 Regulator to Panel Cable
3 ‘Y’ Adaptors
4 Fastening Peg
5 Canvas Carry Bag
1
5
2
4
3
2
Page 4
THE FOLDING SOLAR MODULE
Tempered Glass
Coating
Monocrystalline
Construction
Strong
Aluminium
Frame
Plastic
End Caps
Quality MC4
Connectors
Diode Protected
Junction Box
Strong
Hinges
Custom Designed
Legs
3
Page 5
90WATT MONO FOLDING PANEL
1076mm 534mm 80mm 35mm
610mm
SPECIFICATIONS
Model SMP1090 Short circuit Current 5.4A
Construction Monocrystalline Tolerance ±3%
Peak Power 90W (2 x 45W) Max system Voltage 1000VDC
Net Weight 11kg Frame Anodized Aluminium
Dimensions (Closed) 610x534x80mm Cable length 5000mm
Dimensions (Open) 610x1076x35mm Operating temp. -40° to +85°C
Max power Voltage 18.0V Std. test conditions
AM1.5 1000W/m² 25°C
Max power Current 5.0A Manufactured in China
Open circuit Voltage 21.6V Certification CE
4
Page 6
120WATT MONO FOLDING PANEL
810mm
1076mm 534mm 80mm
35mm
SPECIFICATIONS
Model SMP1120 Short circuit Current 7.2A
Construction Monocrystalline Tolerance ±3%
Peak Power 120W (2 x 60W) Max system Voltage 1000VDC
Net Weight 14kg Frame Anodized Aluminium
Dimensions (Closed) 810x534x80mm Cable length 5000mm
Dimensions (Open) 810x1076x35mm Operating temp. -40° to +85°C
Max power Voltage 18.0V Std. test conditions
AM1.5 1000W/m² 25°C
Max power Current 6.7A Manufactured in China
Open circuit Voltage 21.6V Certification CE
5
Page 7
150WATT MONO FOLDING PANEL
610mm
1630mm
120mm534mm
SPECIFICATIONS
Model SMP1150 Short circuit Current 9.0A
Construction Monocrystalline Tolerance ±3%
Peak Power 150W (3 x 50W) Max system Voltage 1000VDC
Net Weight 16.5kg Frame Anodized Aluminium
Dimensions (Closed) 610x534x120mm Cable length 5000mm
Dimensions (Open) 610x1630x35mm Operating temp. -40° to +85°C
Max power Voltage 18.0V Std. test conditions
AM1.5 1000W/m² 25°C
Max power Current 8.3A Manufactured in China
Open circuit Voltage 21.6V Certification CE
6
Page 8
SYSTEM INSTALLATION
ANGLE TO THE SUN
REDARC solar panels will perform at their peak with the panel face angled directly towards the sun.
In practice this is not always achievable, so REDARC recommend having your panels face NORTH at
an angle of between 20° and 40° from the ground. This will ensure the best total output from your
panel across the course of the day, no matter what season.
In the southern hemisphere, the sun is always in the NORTH half of our sky. As such facing your
panel NORTH ensures the best angle to the sun for a fixed panel across the course of the day.
N
W E
Panel
facing
NORTH
S
Path of
the Sun
always
NORTH
Angle to Sun
between 10°
and 40°
GROUND
The optimal angle from ground of the panel is around 30°. Anywhere between 10° and 40° ensures
good power generation across the course of the day.
SYSTEM WIRING
INSTALLATION NOTES
• Before connecting your solar panel confirm the battery is properly connected.
• Always ensure the connection at Anderson plug is clean, sound and is wired with the correct polarity.
• Redarc recommend the regulator be installed as close as possible to the battery/s. If you need to
use different cables ensure their length does not exceed 10m from the panel to the regulator.
• The supplied MC4 connectors are suitably rated for up to 30A, if multiple panels are used to the point
of exceeding this rating, alternative connectors should be sourced.
• When connecting panels from an existing setup, or non-Redarc brand panels, please ensure that the
panels are diode protected, as they may be damaged if they are not.
• Please refer to Solar Regulator manual and Battery Manufacturer’s specifications for specific
installation instructions.
7
Page 9
SYSTEM WIRING
STANDARD SETUP (90W AND 120W)
Solar Regulator
(Not Supplied)
+
+
---
+
Supplied
Y-Adaptors
STANDARD SETUP (150W)
Supplied
Y-Adaptors
5.0m with 50A
Anderson Supplied
Anderson Supplied
Supplied
5.0m with 50A
Not
Not
Supplied
Fuse
Solar Regulator
(Not Supplied)
+
+
---
+
Not
Supplied
Not
Supplied
8
Fuse
Page 10
REDARC SOLAR PRODUCT WARRANTY
Over the last three decades our company has established a reputation as the power conversion specialist.
A 100% Australian-owned company, we have met the needs of customers in transport and other industries through exciting, innovative thinking.
We believe in total customer satisfaction and practice this by offering our customers:
• Technical advice free of jargon and free of charge
• Prompt turnaround of orders throughout Australia and globally
• Friendly, personalised, professional service and product support
In the unlikely event that a technical issue arises with a Redarc product, customers are encouraged to initially contact the Redarc Technical
Support Team on (08) 8322 4848 or power@redarc.com.au for prompt and efficient diagnosis and product support.
Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major
failure and compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail
to be of acceptable quality and the failure does not amount to a major failure.
The benefits of this Warranty are in addition to other rights and remedies available at law in respect of the Solar Products and shall not derogate from any
applicable mandatory statutory provisions or rights under the Australian Consumer Law.
Redarc Electronics Pty Ltd atf the Redarc Trust trading as Redarc Solar (“Redarc”) offers a warranty in respect of its Solar Products where the Solar Products
are purchased from an authorised Redarc Solar distributor or reseller by a person (“Purchaser”), on the terms and conditions, and for the duration, outlined
below in this document (“Warranty”).
1. In this Warranty, the term Solar Products means:
1.1 Redarc Solar Monocrystalline Solar Panels;
1.2 Redarc Solar Monocrystalline Folding Portable Solar Panel Kits;
1.3 Redarc Solar Monocrystalline Folding Solar Panels;
1.4 Redarc Solar Amorphous Flexible Solar Panels;
1.5 Redarc Solar Amorphous Folding Solar Panels;
(collectively the “Modules”);
1.6 Redarc Solar Regulators and Displays;
1.7 all other solar products manufactured or supplied by Redarc
that are designed for use in recreational vehicles and boats, not
otherwise specifically referred to in this clause 1; and
1.8 any component of or accessory for any product in clause 1.1 to
1.7 (inclusive) manufactured or supplied by Redarc.
Offer and duration of product warranties
2. Subject to this clause 2, Redarc warrants that its Solar Products will be
free, under normal application, installation, use and service conditions,
from defects in materials and workmanship affecting normal use, for
the relevant periods set out below:
2.1 Redarc Solar Monocrystalline Solar Panels – 5 years from the
date of purchase;
2.2 Redarc Solar Monocrystalline Folding Portable Solar Panel Kits –
5 years from the date of purchase;
2.3 Redarc Solar Monocrystalline Folding Solar Panels – 2 year from
the date of purchase;;
2.4 Redarc Solar Amorphous Flexible Solar Panels – 2 years from the
date of purchase;
2.5 Redarc Solar Amorphous Folding Solar Panels – 2 years from the
date of purchase;
2.6 Redarc Solar Regulators and Displays – 2 years from the date of
purchase; and
2.7 all other Solar Products not otherwise set out in this clause 2 – 2
years from the date of purchase.
3. Where a Solar Product malfunctions (excluding as a result of a
reduction in power output levels, which is the subject of clause 4) or
becomes inoperative during the relevant warranty period applicable to
that Solar Product pursuant to clause 2, due to a defect in materials or
workmanship, as determined by Redarc, then subject to further rights
conferred by the Australian Consumer Law on the Purchaser, Redarc
will, in exercise of its sole discretion, either:
3.1 repair the defective Solar Product;
3.2 replace the defective Solar Product; or
3.3 provide a refund to the Purchaser for the purchase price paid for
the defective Solar Product,
without charge to the Purchaser.
4. Redarc warrants that:
4.1 if any Redarc Solar Monocrystalline Solar Panels or any Redarc
Solar Monocrystalline Folding Portable Solar Panel Kits exhibit a
power output of less than 80% of Peak Power under Standard
Test Conditions, within 25 years of the date of purchase;
4.2 if any Redarc Solar Monocrystalline Folding Solar Panels, Redarc
Solar Amorphous Flexible Solar Panels or any Redarc Solar
Amorphous Folding Solar Panels exhibit a power output of less
than 80% of Peak Power under Standard Test Conditions, within
5 years of the date of purchase;
and such loss of power is determined by Redarc to be due to a
defect in materials or workmanship, then subject to further rights
conferred by the Australian Consumer Law on the Purchaser,
Redarc will, in exercise of its sole discretion, either:
4.3 make up the loss in power by supplying the Purchaser with
relevant additional Modules; or
4.4 repair or replace the defective Modules,
without charge to the Purchaser.
5. For the purposes of clause 4:
5.1 Peak Power means the minimum peak power level in Watts that
a Module generates in its maximum power point (as stated on the
label affixed to the Module or on the product information sheet
accompanying the Module); and
5.2 Standard Test Conditions means:
(a) light spectrum of AM 1.5;
(b) an irradiation of 1,000 Watts per square metre; and
(c) a cell temperature of 25 degrees centigrade at right angle
irridation,
the measurements being carried out in accordance with
IEC61215 as tested at the connectors or junction box terminals
(as applicable) per the calibration and testing standards of Redarc
in effect on the date of manufacture of the Module.
6. The warranties given by Redarc in clauses 2 to 4 cover the reasonable
costs of delivery and installation of any repaired or replaced Solar
Products or components of Solar Products to the Purchaser’s usual
residential address notified to Redarc, together with the reasonable
costs of removal and return of any Solar Products determined by
Redarc to be defective.
7. If the Purchaser incurs expenses of the nature referred to in clause 6 in
the context of making a claim pursuant to this Warranty that is accepted
by Redarc, the Purchaser will be entitled to claim for reimbursement of
those expenses which Redarc determines, in exercise of its sole
Page 11
discretion, to be reasonably incurred, provided that the claim is notified
to Redarc in writing at the postal address or email address specified in
clause 23 and includes:
7.1 details of the relevant expenses incurred by the Purchaser; and
7.2 proof of the relevant expenses having been incurred by the
Purchaser.
Exclusions and limitations
8. This Warranty will not apply to, or include any defect, damage, fault,
failure or malfunction of a Solar Product, which Redarc determines to
be due to:
8.1 normal wear and tear or exposure to weather conditions over
time;
8.2 accident, misuse, abuse, negligence, vandalism, alteration or
modification;
8.3 non-observance of any of the instructions supplied by Redarc,
including instructions concerning installation, configuring,
connecting, commissioning, use or application of the Solar
Product, including without limitation choice of location;
8.4 failure to ensure proper maintenance of the Solar Product strictly
in accordance with Redarc’s instructions or failure to ensure
proper maintenance of any associated equipment or machinery;
8.5 repairs to the Solar Product that are not strictly in accordance
with Redarc’s instructions;
8.6 installation, repairs or maintenance of the Solar Product by, or
under the supervision of, a person who is not a qualified auto
electrician or technician, or if non-genuine or non-approved parts
have been fitted;
8.7 faulty power supply, power failure, electrical spikes or surges,
lightning, flood, storm, hail, extreme heat, fire or other occurrence
outside the control of Redarc;
8.8 use other than for any reasonable purpose for which the Solar
Product was manufactured;
8.9 any indirect or incidental damage of whatever nature outside the
control of Redarc.
9. Warranty claims in respect of a Solar Product must be made in writing
to Redarc at the postal address or email address specified in clause
23 within the relevant warranty period applicable to that Solar Product
pursuant to clause 2 or clause 4. Such claims must include the
following:
9.1 details of the alleged defect or fault and the circumstances
surrounding the defect or fault;
9.2 evidence of the claim, including photographs of the Solar Product
(where the subject of the claim is capable of being photographed);
9.3 the serial number of the Solar Product, specified on the label
affixed to the Solar Product; and
9.4 proof of purchase documentation for the Solar Product from an
authorised distributor or reseller of Redarc, which clearly shows
the date and place of purchase.
The return of any Solar Products without the prior written instructions of
Redarc will not be accepted by Redarc.
10. Without limiting any other clause in this Warranty, Redarc has the right
to reject any warranty claim made by a Purchaser pursuant to this
Warranty where:
10.1 the Purchaser does not notify Redarc in writing of a warranty
claim within relevant warranty period applicable to that Solar
Product;
10.2 the Purchaser does not notify Redarc in writing of a warranty claim
within 1 month of becoming aware of the relevant circumstances
giving rise to the claim, so that any further problems with the
Solar Product are minimised;
10.3 the serial number of the Solar Product has been altered, removed
or made illegible without the written authority of Redarc;
10.4 the Purchaser is unable to provide proof of purchase
documentation in accordance with clause 9.4 or evidence
that the Solar Product was properly installed, and that proper
maintenance has been performed on the Solar Product, by, or
under the supervision of, a qualified auto electrician or technician,
in accordance with the instructions of Redarc.
11. If the Solar Product is found to be working satisfactorily on return
to Redarc or upon investigation by Redarc, the Purchaser must pay
Redarc’s reasonable costs of testing and investigating the Solar
Product in addition to shipping and transportation charges. Where
Redarc is in possession of the Solar Product, the Solar Product will be
returned to the Purchaser on receipt of the amount charged.
12. Any replaced Solar Products or components of Solar Products shall
become the property of Redarc.
13. Redarc may, in exercise of its sole discretion, deliver another type
of Solar Product or component of a Solar Product (different in size,
colour, shape, weight, brand and/or other specifications) in fulfilling
its obligations under this Warranty, in the event that Redarc has
discontinued manufacturing or supplying the relevant Solar Product
or component at the time of the warranty claim, or where such Solar
Product or component is superior to that originally purchased by the
Purchaser.
Other conditions of Warranty
14. If the Purchaser acquired a Solar Product for the purpose of resupply,
then this Warranty shall not apply to that Solar Product.
15. In particular, the sale of a Solar Product via an online auction, online
store or other internet website by a party that is not an authorised
distributor or reseller of the Solar Product will be deemed to be a
resupply within the meaning of the Australian Consumer Law and will
render this Warranty void, as Redarc has no control over the storage,
handling, quality or safety of Solar Products sold by such persons.
16. A Purchaser shall only be entitled to the benefit of this Warranty after all
amounts owing in respect of the Solar Product have been paid.
17. While Redarc warrants that the Solar Products will be free from defects
in materials and workmanship in the circumstances set out in this
Warranty, to the maximum extent permitted by law Redarc does not
warrant that the operation of the Solar Products will be uninterrupted or
error-free.
18. To the maximum extent permitted by law, Redarc’s determination of the
existence of any defect and the cause of any defect will be conclusive.
19. Spare parts or materials for the Solar Products are guaranteed to be
available for a period of at least 2 years after purchase of the Solar
Products.
20. The agents, officers and employees of any distributor or reseller of the
Solar Products and of Redarc are not authorised to vary or extend the
terms of this Warranty.
21. Redarc shall not be responsible or liable to the Customer or any third
party in connection with any non-performance or delay in performance
of any terms and conditions of this Warranty, due to acts of God, war,
riots, strikes, warlike conditions, plague or other epidemic, fire, flood,
blizzard, hurricane, changes of public policies, terrorism and other
events which are beyond the control of Redarc. In such circumstances,
Redarc may suspend performance of this Warranty without liability for
the period of the delay reasonably attributable to such causes.
22. If a clause or part of a clause in this Warranty can be read in a way
that makes it illegal, unenforceable or invalid, but can also be read
in a way that makes it legal, enforceable and valid, it must be read
in the latter way. If any clause or part of a clause in this Warranty is
illegal, unenforceable or invalid, that clause or part is to be treated
as removed from this Warranty, but the rest of this Warranty is not
affected.
Redarc’s contact details
23. Redarc’s contact details for the sending of warranty claims under the
Warranty are:
Redarc Electronics Pty Ltd
23 Brodie Road (North), Lonsdale SA 5160
Email: power@redarc.com.au
Telephone: +61 8 8322 4848
Page 12
AUSTRALIAN DESIGNED AND ENGINEERED
This product has been specified and tested in Australia in accordance with REDARC specifications and
testing requirements by REDARC Engineers. You can be assured that this product meets the stringent
quality levels of all REDARC products.
WARMONOSMPS - REV1
For free technical assistance please contact
Redarc Electronics
23 Brodie Road North, Lonsdale SA
(08) 8322 4848
power@redarc.com.au
www.redarcsolar.com.au
Copyright © 2014 Redarc Electronics Pty Ltd. All rights reserved.
This product is manufactured in China.
Loading...