RECTRON RL102F, RL101F, RL105F, RL107F, RL106F Datasheet
...
RECTRON
SEMICONDUCTOR
TECHNICAL SPECIFICA TION
FAST RECOVERY RECTIFIER
VOLTAGE RANGE 50 to 1000 Volts CURRENT 1.0 Ampere
FEATURES
* Fast switching
* Low leakage
* Low forward voltage drop
* High current capability
* High currenf surge
* High reliability
MECHANICAL DATA
* Case: Molded plastic
* Epoxy: Device has UL flammability classification 94V-O
* Lead: MIL-STD-202E method 208C guaranteed
* Mounting position: Any
* Weight: 0.33 gram
MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS
Ratings at 25 oC ambient temperature unless otherwise specified.
Single phase, half wave, 60 Hz, resistive or inductive load.
For capacitive load, derate current by 20%.
.205 (5.2
.166 (4.2
1.0 (25.4
MIN.
)
)
1.0 (25.4
MIN.
RL101F
THRU
RL107F
.025 (0.6
.021 (0.5
)
.107 (2.7
.080 (2.0
)
A-405
)
DIA.
)
)
DIA.
)
Dimensions in inches and (millimeters)
MAXIMUM RATINGS
Maximum Recurrent Peak Reverse Voltage
Maximum RMS Voltage
Maximum DC Blocking Voltage
Maximum Average Forward Rectified Current
at TA = 55oC
Peak Forward Surge Current 8.3 ms single half sine-wave
superimposed on rated load (JEDEC method)
Typical Junction Capacitance (Note 2)
Operating and Storage Temperature Range
ELECTRICAL CHARACTERISTICS
Maximum Instantaneous Forward Voltage at 1.0A DC Volts
Maximum DC Reverse Current
at Rated DC Blocking Voltage TA = 25oC
Maximum Full Load Reverse Current Full Cycle Average,
.375” (9.5mm) lead length at TL = 55oC
Maximum Reverse Recovery Time (Note 1)
NOTES : 1. Test Conditions: IF = 0.5A, IR = -1.0A, IRR = -0.25A
2. Measured at 1 MHZ and applied reverse voltage of 4.0 volts
(At TA = 25oC unless otherwise noted)
RATINGS
(At TA = 25oC unless otherwise noted)
CHARACTERISTICS
SYMBOL
V
RRM
V
RMS
V
DC
I
O
I
FSM
C
J
TJ, T
STG
SYMBOL
V
F
I
R
trr
RL101F RL102F RL103F RL104F RL105F RL106F RL107F UNITS
50 100 400 800 1000
35
50
RL101F RL102F RL103F RL104F RL105F RL106F RL107F UNITS
200
70
140
100
200
-65 to + 150
150 250 500
280
400
1.0
30
15
1.3
5.0
100
600
420
600
560
800
700
1000
uAmps
uAmps
Volts
Volts
Volts
Amps
Amps
pF
0
C
nSec
2001-5
RATING AND CHARACTERISTIC CURVES
(
RL101F THRU RL107F
)
FIG. 1 - TYPICAL FORWARD CURRENT
DERATING CURVE
1.0
.8
.6
.4
Single Phase
Half Wave 60Hz
.2
Resistive or
Inductive Load
0
AVERAGE FORWARD CURRENT, (A)
0 25 50 75 100 125 150 175
AMBIENT TEMPERATURE, ( )
FIG. 3 - TYPICAL INSTANTANEOUS
FORWARD CHARACTERISTICS
20
10
3.0
1.0
0.3
0.1
TJ = 25
Pulse Width=300uS
1% Duty Cycle
.03
.01
INSTANTANEOUS FORWARD CURRENT, (A)
0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8
INSTANTANEOUS FORWARD VOLTAGE, (V)
FIG. 2 - MAXIMUM NON-REPETITIVE FORWARD
SURGE CURRENT
50
8.3ms Single Half Sine-Wave
(JEDED Method)
40
30
20
CURRENT, (A)
10
PEAK FORWARD SURGE
0
1 2 4 6 810 20 40 6080100
NUMBER OF CYCLES AT 60Hz
FIG. 4 - TYPICAL REVERSE CHARACTERISTICS
10
6
4
2
1.0
.6
.4
.2
TJ = 25
.1
.06
.04
.02
.01
INSTANTANEOUS REVERSE CURRENT, (uA)
0 20 40 60 80 100 120 140
PERCENT OF RATED PEAK REVERSE VOLTAGE, (%)
FIG. 5 - TYPICAL JUNCTION CAPACITANCE
200
100
60
40
20
10
6
TJ = 25
4
2
JUNCTION CAPACITANCE, (pF)
1
.1 .2 .4 1.0 2 4 10 20 40 100
REVERSE VOLTAGE, ( V )
FIG. 6 - TEST CIRCUIT DIAGRAM AND REVERSE
RECOVERY TIME CHARACTERISTIC
50
NONINDUCTIVE10NONINDUCTIVE
D.U.T
( + )
25 Vdc
(approx)
( - )
1
NONINDUCTIVE
1 Rise Time = 7ns max. Input Impedance =
NOTES:
1 megohm. 22pF.
2. Rise Time = 10ns max. Souce Impedance =
50 ohms.
OSCILLOSCOPE
(NOTE 1)
+0.5A
( - )
PULSE
GENERATOR
(NOTE 2)
0
-0.25A
( + )
-1.0A
RECTRON
trr
1cm
SET TIME BASE FOR
50/100 ns/cm
Loading...