Rectorseal CLEAN CHECK Installation Manual

INSTALLATION INSTRUCTIONS

713-263-8001 800-231-3345 713-263-7577 800-441-0051 www.rectorseal.com

RectorSeal brand solvent cements are approved to meet manufacturer’s recommendations.

CLEAN

CHECK ®

Extendable Backwater Valve

◄ OUTER

RISER PIPE

FLOW ►

Flow ►◄ Building

Pre-Installation

• Slide Upper Collar through

Outer Riser Pipe. If collar does

not slide freely through pipe,

check to see if pipe is

“out-of-round”. If so, replace

Outer Riser Pipe.

• Backwater valves require

adequate drop between the

ood rim of the lowest xture

and burial depth of the valve in

order to function properly.

We recommend a minimum

slope of 1/4” per foot or as

recommended by the UPC

and IPC codes.

• Additional PVC bushings are

enclosed for use if needed.

Discard if not used.

FINGER HOLE

▼

▲

THUMB SCREW

◄ THREADED PLUG
& ADAPTOR
Optional

NOTCH

▼

▲

REFERENCE

NOTCH

See step 8

Inner Riser Assembly

Outer Riser Assembly

VALVE BODY ▲

SEWER LATERAL ▲

Outer Riser Installation

At proper depth, install the Clean Check Valve Body

1

between the building and the sewer lateral, with the “FLOW”
arrow of the Valve Body pointing downstream away
from the building.

Rotate the Valve Body until the opening is facing directly

2

upward. A level may be used across the top of the Valve Body
to verify horizontal positioning.

Cut the Outer Riser Pipe to the required length. Cement

3

and insert while keeping the inside of the body clean of debris.

CAUTION: Be certain that excess solvent cement has not

impeded proper seating of the Flapper Assembly or the proper
seating of the apper sealing surface of the Valve Body.

Inner Riser Installation

4

Cut the Inner Riser Pipe to a length (3-1/2”) shorter than
the Outer Riser Pipe.

5

Cement the Flapper Assembly to one end of the Inner
Riser Pipe.

OUTER RISER PIPE ►

not included

INNER RISER PIPE ►

Parts not provided

• Standard 8” or 6" ABS or

PVC Outer Riser Pipe of re-

quired length, and one 8" or 6"

Threaded Adaptor & Plug

(8" or 6" Outer Riser Pipe

is determined by the Clean

Check model to be used)

• Standard 4” ABS or PVC

Inner Riser Pipe of required

length.

FLAPPER ASSEMBLY ►

BUSHING ►

Bushings are provided for PVC

schedule 40x SDR-35 installations

Building

not included

◄ FLAPPER

Heavy Duty

Rated at 75 PSI

6

Cement the Upper Collar to the other end of the Inner Riser
Pipe, while aligning the center of the Finger Hole with the center
of the Flapper on the opposite end.

7

When cement is dry, loosen the thumb screw in the Upper Collar

and slide the Inner Riser Assembly – Flapper Assembly rst –
into the Outer Riser Assembly with the at sealing side of the

Flapper facing the inlet side of the Valve Body. Lower the Inner
Riser Assembly into the seating area of the Valve Body, making
certain that the Thumb Screw is inside the inside wall of
the Outer Riser Pipe and NOT on
the resting on the top edge. Seat
the Flapper Assembly by rotating
as necessary until it locks in place.
Visually inspect that the Flapper
Assembly is installed correctly.

IMPORTANT: Prior to installation

8

of the Threaded Adaptor & Plug
(with the Inner Riser Assembly
properly installed) cut a reference
notch into the Outer Riser Pipe.
This saw cut notch should be
aligned with the molded Notch in
the Upper Collar. For future removal,
alignment of the notches will
quickly indicate that the apper is
seated correctly.

VALVE BODY ►

®

Contact: RectorSeal

P F W

9

IMPORTANT: Tighten the ¼” Stainless Steel Thumb Screw

until it seats snugly against the Inner Riser Pipe, xing the Inner

Riser Assembly in place.

Cement the Threaded Adapter to the Outer Riser Pipe

10

riser and screw the Threaded Plug into the
Threaded Adapter to complete installation.

Sewer

Hubsett™ Test Coupling

Application

• Allows the buildings drain waste and vent system to be connected to the

sewer line prior to the initial test • Easily removed with one
quick pull on the release cord

Recommended for

Includes

• Uniquely designed coupling and test device all in one

• ABS • PVC

• Dome • Coupling • Float

Float

Dome

Coupling

R

E

I

A

N

D

-

S

Y

T

T

O

O

C

K

S

H

I

P

FEATURES

• Holdspressureeverytime

• Safetouse

• Nopumporspecialtools
 needed

• Testwithairorwater

• 12ft.cord

Scan for more info

Tom-Kap™ Flush-t cleanout adaptor & plug

Application

flush-finished cleanout for DWV systems

Recommended for

Includes

• Threaded adapter cements inside the pipe, providing a

• Schedule 40 • SDR-35 • Foam core

• Top fitting • Cap

FEATURES

• Reducesinstallationcost

• Simplifiesrough-in

RectorSeal®

2601 Spenwick Drive - Houston, TX 77055

ph: 713.263.8001 - 800.231.3345

fax: [phone]

www.rectorseal.com - Like Us on Facebook

Scan for more info