Rear view safety RVS-25W Instruction Manual

Instruction Manual

Wireless Backup Camera System

5" Dual Screen Display

RVS-25W

Please read this manual before using the product.

The product may be dierent from how it is described in the manual

depending on what software version you are using.

Reverse With Condence ™

1

Introduction.............................. 03

Safety Information.............................. 04-06

Before Beginning Installation ....................... 07

Precautions.......................... . . . . 08

TABLE OF CONTENTS

Features...............................09

Technical Parameters ..............................10

Applications.................................11

Monitor Menu Operation...........................12 -13

Monitor OSD Menu Operation. . . . . . . . . . . . . . . . . . . . . . 14-15

Troubleshooting.......................... . . . . 16

Warranty.......................... . . . . . . 17

Disclaimer.......................... . . . . . 18

2

Rear View Safety

NOTE!

Please read all of the installation instructions
carefully before installing the product. Improper
installation will void manufacturer’s warranty.

Congratulations on purchasing a Rear View Backup

Camera System!

With this manual you will be able to properly install and

operate the unit.

The Backup Camera System is intended to be installed as a
supplement aid to your standard rear view mirror that already exists
in your vehicle. The Backup Camera System should not be used as a
substitute for the standard rear view mirror or for any other mirror

that exists in your vehicle.

In some jurisdictions, it is unlawful for a person to drive a
motor vehicle equipped with a TV viewer or screen located forward of
the back of the driver’s seat or in any location that is visible, directly

or indirectly, to the driver while operating the vehicle.

INTRODUCTION

Reverse With Condence ™

3

Please read the entire manual and follow the instructions and

warnings carefully. Failure to do so can cause serious damage and/or

injury, including loss of life. Be sure to obey all applicable local

trac and motor vehicle regulations as it pertains to this product.

Improper installation will void manufacturer’s warranty.

USAGE:

• The Rear View Camera System is

designed to help the driver safe­ly detect people and/or objects
helping to avoid damage or injury.
However, you the driver, must use it
properly. Use of this system is not a
substitute for safe, proper or legal
driving.

• Never back up while looking at the

monitor alone. You should always

damage or injury. Always back up
slowly.

• The Rear View Camera System is

not intended for use during exten­sive back-up maneuvers or backing
into cross trac or pedestrian walk­ways.

•Please, always remember, the area

displayed by the Rear View Camera

check behind and around the vehi-

SAFETY INFORMATION

cle when backing up, in the same
way as you would if the vehicle did
not have the Rear View Camera
System. If you back up while looking
only at the monitor, you may cause

4

System is limited. It does not display
the entire panorama that is behind
you.

Rear View Safety

INSTALLATION:

• Electric shock or product

malfunction may occur if this
product is installed
incorrectly.

• Use this product within

the voltage range specied. Failure
to do so can cause
electronic shock or product
malfunction.

or disconnected wire may cause a
re.

• While installing the Rear View

System be careful with the wire
positioning in order to avoid wire
damage.

• The Rear View System should only

be used when the vehicle is in
reverse.

SAFETY INFORMATION

• Take special care when

cleaning the monitor.

• Make sure to rmly ax the prod-

uct before use.

• If smoke or a burning smell

is detected, disconnect the
system immediately.

• Where the power cable may touch

• Do not watch movies or

operate the monitor while driving;
as it may cause an
accident.

• Do not install the monitor

where it may obstruct drivers
view or obstruct an air bag
device.

a metal case, cover the cable with
friction tape. A short circuit

• Dropping the unit may cause

possible mechanical failure.

Reverse With Condence ™

5

If you have questions about this product, contact:

Rear View Safety

1797 Atlantic Avenue

Brooklyn, NY 11233

Tel: [phone]

IN NO EVENT SHALL SELLER OR MANUFACTURER BE

SAFETY INFORMATION

LIABLE FOR ANY DIRECT OR CONSEQUENTIAL DAMAGES OF

ANY NATURE, OR LOSSES OR EXPENSES RESULTING FROM

ANY DEFECTIVE PRODUCT OR THE USE OF ANY PRODUCT.

6

Rear View Safety

Before drilling please check that no cable or wiring is on the other side
of the wall. Please clamp all wires securely to reduce the possibility
of them being damaged while vehicle is in use. Keep all cables away

from hot/moving parts and electrical noisy components.

We recommend doing a benchmark test before installation

to insure that all components are working properly.

Step 1: Choose the monitor and camera locations.

Step 2: Install all cables in vehicle, when necessary a 0.8 (20mm)
hole should be drilled for passing camera cable through vehicles
walls. Install split grommets where applicable.

Step 3: Once all cables and wiring have been properly routed, perform
a system function test by temporarily connecting the system.

BEFORE YOU BEGIN

Reverse With Condence ™

7

Operating Precautions

1. The device may be powered by a 12 or 24 volt battery or the vehicle's
electrical system.

2. Make sure all cables are connected properly. Improper cable con­nections may damage the monitor. Remove the power cable connections
when not using the device.

3. The back-up battery can be recharged when the power is on.

4. When battery is fully charged, recharging will automatically stop.

5. If batteries are not used for a while, it may take longer to charge.

Warning!

1. This monitor is high voltage. Only professionals should open the
monitor's case.

2. Do not watch the video while driving unless you are monitoring the
rear view camera display.

Special Note

Occasionally, a few highlights or dark spots may appear on the LCD screen. This

PRECAUTIONS

doesn’t necessarily indicate any monitor defects. Never try to repair this device
yourself. If any problems occur, immediately turn the display o and notify our
company or an authorized dealer. Any disassembly or modication may lead to
damage and will also void the warranty.

8

Rear View Safety

Features

ABS monitor housing that can endure high temperatures.

- 5" High resolution color TFT- LCD.

- Power input:8V-32V DC.

- Monitor circuit has protector for battery reverse (+/-).

- LED backlight display with constant voltage and constant current
circuit protection. It can solve LED working temperature problems
(the limit of LED backlight’s current) and prolong life.

- OSD menu can set each channel camera image in 4 modes NOR/
MIR/UP/DOWN; change the priority for each mode; each trigger cable
can be set to trigger to any display mode; time delay setting.

- Two channel digital wireless signal transmission. It supports sub­screen and two screens.

- Camera waterproof rating: IP69K.

FEATURES

Reverse With Condence ™

9

Technical Parameters

Resolution

800×(RGB)×480

Display Device Color TFT-LCD

Size 5" Digital Screen

Operation Frequency 2400 ~ 2483.5MHz

Receiving Sensitivity ≤- 86dBm(1MHZ QPSK MD300RE)

View Angle (LR/UD) L/R: 70/70 U/D: 50/70

Contrast Ratio 300:1

Luminance(cd/m ) 300

Response Time (ms) 25

Load Dump

Operating Temperature -20℃ ～+60℃

Storage Temperature -30℃ ～+80℃

operating voltage range

Dimension( L x W x T) 139X100X55( mm)

Transmission Power

Camera Color CMOS Camera

Image Pick- up Device 1/3" Color CMOS

Picture Elements NTSC:720(H)X480(V);PAL:720(H)X480(V)

Horizontal Resolution 500 TV Lines

Minimum illumination 0 Lux At Night ( IR LED ON)

2

DC 12+87V/400ms

DC8V～32V （ 5W Max）

18dBm with Power control

View Angle 120°

Waterproof rating IP69K

TECHNICAL PARAMETERS

Shockproof R ating 10G

operating voltage range DC11~32V

Dimension 106(W) x 75(H) x 70.4(D) mm

WARNING: This system should only be repaired by professionals. Please do not open and repair
the system yourself. This manual is for reference only.

10

Rear View Safety

Applications

APPLICATIONS

Reverse With Condence ™

11

Monitor Menu Operation

PAIRING SART
50

PAIRING START

1. Pair
First establish a connection between the monitor
and camera. Enter the menu, chose PAIR and press OK. The monitor will

MONITOR MENU OPERATION

display PAIRING START 50. After 50 seconds, re-energize the camera
and the monitor will show the camera image in 5~10s.

12

Rear View Safety

­5

+

­5

­5

2. Picture setting
Enter the menu, chose the picture and press OK,

1. Brightness: 0-10 (Press left/right to adjust)

+

+

MONITOR MENU OPERATION

2. Contrast: 0-10 (Press left/right to adjust)

3. Color: 0-10 (Press left/right to adjust)

Reverse With Condence ™

13

F

F

F

3. Mirror/Normal image setting:
Set the CAM1 and CAM2 image in 4 modes.

F

MONITOR OSD MENU OPERATION

4. Auto Scan setting:

1. Set CAM1 auto scan mode on/off;

2. Set CAM2 auto scan mode on/off;

3. Set the auto scan time.

14

-

Rear View Safety

5

+

ON OFF

ON OFF

5. Other functions:

1. NTSC or PAL system switch.

2. LED screen ambient light sensor on/off.

3. Electronic Label setting: Turn on/off the electronic label on CAM1.

MONITOR OSD MENU OPERATION

Note:
When the monitor is in SCAN mode, the CAM1 and CAM2 image will
switch automatically according to the setting time. Press / to choose
an image.

Reverse With Condence ™

15

No Image On Screen

• Do a hard reset, unplug all cables

and power cables, leave out for 1
minute and then re-connect them

• Check to ensure that the

connection to the camera is tight

• Verify camera cable is plugged into

port labeled Backup Camera

• Verify that the green positive

• Verify camera is on correct camera

input

• Verify cable is connected to

monitor

• Verify camera is connected to

cable

• Connect known working camera

and cable to monitor
trigger on power harness is put to
power 12v+

TROUBLESHOOTING

• Verify Green trigger is receiving

power

16

Rear View Safety

ONE YEAR WARRANTY

RVS SYSTEMS, INC. WARRANTS THIS PRODUCT AGAINST MATERIAL DEFECTS FOR A PERIOD
OF ONE YEAR FROM DATE OF PURCHASE. WE RESERVE THE RIGHT TO REPAIR OR REPLACE
ANY SUCH DEFECTIVE UNIT AT OUR SOLE DISCRETION. RVS SYSTEMS, INC. IS NOT RESPON
SIBLE FOR A DEFECT IN THE SYSTEM AS A RESULT OF MISUSE, IMPROPER INSTALLATION,
DAMAGE OR MISHANDLING OF THE ELECTRONIC COMPONENTS. RVS SYSTEMS, INC. IS NOT

RESPONSIBLE FOR CONSEQUENTIAL DAMAGES OF ANY KIND.

THIS WARRANTY IS VOID IF: DEFECTS IN MATERIALS OR WORKMANSHIP OR DAMAGES

RESULT FROM REPAIRS OR ALTERATIONS WHICH HAVE BEEN MADE OR ATTEMPTED BY
OTHERS OR THE UNAUTHORIZED USE OF NONCONFORMING PARTS; THE DAMAGE IS DUE
TO NORMAL WEAR AND TEAR, THIS DAMAGE IS DUE TO ABUSE, IMPROPER MAINTENANCE,
NEGLECT OR ACCIDENT; OR THE DAMAGE IS DUE TO USE OF THE RVS SYSTEMS, INC. SYSTEM

AFTER PARTIAL FAILURE OR USE WITH IMPROPER ACCESSORIES.

WARRANTY PERFORMANCE

DURING THE ABOVE WARRANTY PERIOD, SHOULD YOUR RVS SYSTEMS PRODUCT
EXHIBIT A DEFECT IN MATERIAL OR WORKMANSHIP, SUCH DEFECT WILL BE REPAIRED WHEN
THE COMPLETE RVS SYSTEMS, INC. PRODUCT IS RETURNED, POSTAGE PREPAID AND IN

SURED, TO RVS SYSTEMS, INC. OTHER THAN THE POSTAGE AND INSURANCE

REQUIREMENT, NO CHARGE WILL BE MADE FOR REPAIRS COVERED BY THIS WARRANTY.

WARRANTY DISCLAIMERS

NO WARRANTY, ORAL OR WRITTEN, EXPRESSED OR IMPLIED, OTHER THE ABOVE WARRANTY
IS MADE WITH REGARD TO THIS RVS SYSTEMS, INC. RVS SYSTEMS, INC. DISCLAIMS ANY IM
PLIED WARRANTY OR MERCHANTABILITY OR FITNESS FOR A PARTICULAR USE OR PURPOSE

AND ALL OTHER WARRANTIES IN NO EVENT SHALL RVS SYSTEMS. INC.

LIABLE FOR ANY INCIDENTAL, SPECIAL, CONSEQUENTIAL, OR PUNITIVE DAMAGES OR FOR

ANY COSTS, ATTORNEY FEES, EXPENSES, LOSSES OR DELAYS ALLEGED TO BE AS A

WARRANTY

CONSEQUENCE OF ANY DAMAGE TO, FAILURE OF, OR DEFECT IN ANY PRODUCT INCLUDING,

BUT NOT LIMITED TO, ANY CLAIMS FOR LOSS OF PROFITS.

Reverse With Condence ™

17

DISCLAIMER

RVS SYSTEMS AND/OR ITS AFFILIATES DOES NOT GUARANTEE OR PROMISE THAT THE USER
OF OUR SYSTEMS WILL NOT BE IN/PART OF AN ACCIDENT OR OTHERWISE NOT COLLIDE WITH
AN OBJECT AND/OR PERSON. OUR SYSTEMS ARE NOT A SUBSTITUTE FOR CAREFUL AND CAU
TIOUS DRIVING OR FOR THE CONSISTENT ADHERENCE TO ALL APPLICABLE TRAFFIC LAWS
AND MOTOR VEHICLE SAFETY REGULATIONS. THE RVS SYSTEMS PRODUCTS ARE NOT A SUB

STITUTE FOR REARVIEW MIRRORS OR FOR ANY OTHER MOTOR VEHICLE
EQUIPMENT MANDATED BY LAW. OUR CAMERA SYSTEMS HAVE A LIMITED FIELD OF VISION
AND DO NOT PROVIDE A COMPREHENSIVE VIEW OF THE REAR OR SIDE AREA OF THE VEHICLE.
ALWAYS MAKE SURE TO LOOK AROUND YOUR VEHICLE AND USE YOUR MIRRORS TO CONFIRM

REARWARD CLEARANCE AND THAT YOUR VEHICLE CAN MANEUVER SAFELY. REAR VIEW

SAFETY AND/OR ITS AFFILIATES SHALL HAVE NO RESPONSIBILITY OR LIABILITY
FOR DAMAGE AND/OR INJURY RESULTING FROM ACCIDENTS OCCURRING WITH VEHICLES
HAVING SOME OF RVS SYSTEMS PRODUCTS INSTALLED AND RVS SYSTEMS AND/OR ITS AF
FILIATES, THE MANUFACTURER, DISTRIBUTOR AND SELLER SHALL NOT BE LIABLE FOR ANY
INJURY, LOSS OR DAMAGE, INCIDENTAL OR CONSEQUENTIAL, ARISING OUT OF THE USE OR
INTENDED USE OF THE PRODUCT. IN NO EVENT SHALL RVS SYSTEMS AND/OR ITS AFFILIATES
HAVE ANY LIABILITY FOR ANY LOSSES WHETHER DIRECT OR INDIRECT, IN CONTRACT, TORT

INCLUDING BUT NOT LIMITED TO DAMAGED PROPERTY, PERSONAL INJURY AND/OR LOSS OF

RESPONSIBILITY FOR ANY DECISION, ACTION OR INACTION TAKEN BY ANY PERSON IN

RELIANCE ON RVS SYSTEMS SYSTEMS, OR FOR ANY DELAYS, INACCURACIES AND/OR ER

DISCLAIMER

OR OTHERWISE INCURRED IN CONNECTION WITH THE SYSTEMS,

LIFE. NEITHER SHALL RVS SYSTEMS AND/OR ITS AFFILIATES HAVE ANY

RORS IN CONNECTION WITH OUR SYSTEMS FUNCTIONS.

18

Rear View Safety

NOTES

Reverse With Condence ™

NOTES

19

If you have any questions

about this product, contact:

Rear View Safety, Inc.

1797 Atlantic Avenue

Brooklyn, NY 11233

800.764.1028

Better Cameras. Better Service.

IT’S OUR GUARANTEE.

20

Rear View Safety