Real Flame G8700 User Manual

gel replaces and accessories

Model # G8700

Frisco Fireplace

2

!

!!

WARNINGS

!

!!

Using your Fireplace

NOTICE: Buyer assumes all responsibility for safety and use

that is not in accordance with instructions and warnings.

- Fireplace is designed to be used indoors, there is no need for ventilation.

- Use extreme caution while burning. Some surfaces become extremely hot during use.

- Follow all instructions included with gel fuel before use.

- Before using fireplace, be sure you have read and understand the step-by-step instructions.

- During the initial burn you may experience a slight odor. Odor is temporary and will be absent on
following burns.

Welcome to the Real Flame family of gel fuel products. If

you have questions please call customer service at
1-800-654-1704 or log on to www.REALFLAME.com

1. Fireplace is designed to be used with Real Flame® gel fuel only. Do not use with any other gel fuel or
any other flammable liquid or gel.

2. Read entire label and instructions before using Real Flame gel fuel.

3. Make sure fireplace is set on a flat, level and stable surface. Keep fireplace stable at all times.

4. Make sure fireplace and gel fuel are burned on a flat and level surface.

5. Never leave a burning fire unattended, especially around children or pets.

6. Fireplace is not to be operated by children. Keep away from children and pets.

7. Exercise the same precautions as you would with any open fire.

8. When in use some surfaces will be hot, use caution.

9. Never touch logs, gel fuel cans or any other metal surfaces during or immediately after burning gel
fuel. They will be extremely HOT. Allow them to cool for 60 minutes before touching.

10. Do not burn more than three cans of fuel at once.

11. Do not place more than 15 lbs. of weight on the top of the fireplace at anytime.

12. Do not alter fireplace, metal firebox or log set in any manner.

13. Keep fireplace and gel fuel cans away from flammable materials at all times.

14. Do not store or use gasoline or any other flammable vapors, liquids, or materials in the vicinity of
fireplace and gel fuel.

15. Do not wear flammable or loose clothing when operating the fireplace.

16. Do not move fireplace while in use. Do not attempt to move or store the fireplace until 60 minutes
after gel fuel cans have been extinguished.

17. Do not burn trash, paper, or wood in the fireplace. Burn only Real Flame® gel fuel in the fireplace.

18. Do not burn gel fuel outside designated burn areas on the metal grate.

19. Do not put fireplace in an area with lots of traffic, such as a hallway or entryway.

20. In case of an emergency use a CO2 extinguisher to extinguish the fire.

21. Death, serious injury or damage to property may occur if the warnings above are not followed.

22. If for any reason you cannot follow these warnings please call us at 1-800-654-1704.

3

Before assembly, locate instructions and hardware. Take out all parts
and compare them to the photograph and the assembly illustrations. Be
sure you have all parts identified.

Check for screws that are wrapped in the packaging to be sure you don't
discard them. You may have extra screws.

A helping hand is always good. Assemble fireplace with an adult
assistant if possible.

The cement log is heavy. Put the fireplace in the desired location before
inserting cement log.

Use caution not to over tighten screw

s.

Parts List

Number Description Part Number Quantity
1 Base 1
2 Left Side Panel 1
3 Right Side Panel 1
4 Left Front Panel 1
5 Right Front Panel 1
6 Center Panel 1
7 Mantel Top 1
8 Left Firebox Trim 1
9 Right Firebox Trim 1
10 Lower Firebox Trim 1
11 Top Firebox Trim 1
12 Firebox Support 1

Not Shown:
Firebox Clips 1075 2

G8701
G8702
G8703
G8704
G8705
G8706
G8707
G8708
G8709
G8710
G8711
G8712

1” Phillips Screws 9713 Bag

4

Step One

- Set base (1) on a at surface.

- Using tongue and groove t the Right Side Panel (3) into the Right
Trim Panel (5). Make sure the bottom edges of the Right Side Panel
and Right Trim Panel are ush. Attach together with three 1” screws
through mounting blocks.

- Repeat with Left Side Panel (2) and Left Trim Panel (4).

- Place assembled Right Panels on base with mounting block on
the inside of Right Side Panel (3) against inside of base as shown in
gure 1. Attach with three 1” screws.

- Repeat process using Left Side Panels.

4

2

5

3

1