Real Flame G8600 Mantel Assembly Instructions

Lot:___________
Mantel Assembly Instructions
Silverton Fireplace
Model # G8600
G8600-Rev1-101911-JW
Dust the mantel periodically as you would with any piece of furniture.
Do not use water to clean mantel. Water may cause swelling, warping or stains if allowed to penetrate the nish of the mantel. Use protective pads or cloths whenever possible.
Avoid placing mantel in rooms with lots of humidity or where humidity could be a problem. This may cause warping to the mantel.
Using your Fireplace
Fireplace is designed to be used indoors, there is no need for ventilation.
Use extreme caution while burning. Some surfaces become extremely hot during use.
Before using replace, be sure you have read and understand the step-by-step instructions and warnings included with your gel fuel or electric rebox.
Care and Cleaning
Helpful Tips for Assembly
IF ANY PARTS ARE DAMAGED OR MISSING PLEASE CALL US DIRECTLY AT:
1-800-654-1704
Prep, plan and clear your space. In order to minimize damage while assembling make sure unpacking and assembly takes place on a carpeted surface.
We recommend to use a power screwdriver for assembly it will greatly reduce your time for assembly. BE SURE NOT TO OVERTIGHTEN SCREWS. The wood can easily be stripped out if too much force is used.
Use two people for assembly of the mantel. Another set of hands will help tremendously with the assembly process and will reduce the amount of time spent on assembly. If you do not have a helper, that is ok too, just take your time and follow the instructions.
Make sure that your mantel has been properly assembled prior to use. Once you have completed assembly you should not have any extra mantel parts. The piece will be quite sturdy and all pieces will t together nic
ely. If you did not achieve ideal results by following the instructions, please contact our customer service
team at 1-800-654-1704 and they will help answer any questions or concerns about the assembly process.
Avoid direct sunlight if possible to reduce the possibility of fading the nish.
Before assembly carefully unpack and check for each replace piece and necessary hardware
2
3
PARTS LIST
Number Description Quantity 1 Base Panel 1 2 Left Side Panel 1 3 Right Side Panel 1 4 Left Front Panel 1 5 Right Front Panel 1 6 Center Panel 1 7 Top Panel 1 8 Left Firebox Trim 1 9 Right Firebox Trim 1 10 Lower Firebox Trim 1 11 Upper Firebox Trim 1 12 Firebox Support 1 13 Hardware Kit 1
HARDWARE KIT-G86000013
A x 24 Short Allen Screw
B x 12 L-Bracket
C x 22 Long Allen Screw
D x 22 Washer
E x 1 Allen Wrench
F x 2 MDF Board
1
2
3
4
5
6
7
8
9
10
12
11
Black 86000101JW 86000102JW 86000103JW 86000104JW 86000105JW 86000106JW 86000107JW 86000108JW 86000109JW 86000110JW 86000111JW 86000112JW 86000013JW
Dark Mahogany
86000501JW 86000502JW 86000503JW 86000504JW 86000505JW 86000506JW 86000507JW 86000508JW 86000509JW 86000510JW 86000511JW 86000512JW 86000013JW
4
Step One
-Join left side panel (2) with left front panel (4) by securing 6 short allen screws (A) through 3 L-brackets (B).
-Repeat with right side panel (3) and right front panel (5).
Step Two
-Set base panel (1) on a flat surface as shown.
-Join panel (2) & (4), (3) & (5) by securing 8 short allen screws (A) through 4 L-brackets (B).
2
4 5
3
A
A
B
2
4 5
3
1
A
A
B
5
Step Three
-Attach left firebox trim (8) to left front panel (4) by securing 2 long allen screws (C) through 2 washers (D). Fit on base panel (1) by securing 2 short allen screws (C) through 1 L-bracket (B).
-Repeat with right firebox trim (9).
Step Four
-Attach lower firebox trim (10) to side firebox trim (8) & (9) by securing 2 long allen screws (C) through 2 washers (D).
-Attach upper firebox trim (11) to front panel (4) & (5) by securing 2 long allen screws (C) through 2 washers (D). Fit on side firebox trim (8) & (9) by securing 4 long allen screws (C) through 4 washers (D) and 2 MDF boards (F).
8
C
8
9
4
5
C
D
C
D
9
1
D
A
A
B
4 5
11
C
D
F
10
Loading...
+ 11 hidden pages