ReadyNet WRT150N User Manual
Wireless Broadband Router
User Manual
REV：1.0
RECYCLABLE
LEDS Description
The Router's LEDs are located on the front panel.
Name Status Indication
PWR
WLAN
WAN
LAN
(1~4)
WPS
Off No Power
On Power on
On The wireless function is enabled
Flashing The wireless is sending and receiving data
Off There is no device linked to the corresponding port
On There are devices linked to the corresponding
ports but no data transmitted or received.
Flashing Sending or receiving data over corresponding port
Off There is no device linked to the corresponding port
On There are devices linked to the corresponding
ports but no data transmitted or received.
Flashing Sending or receiving data over corresponding port
Off The WPS function is disenable
On The WPS function is enable
Flashing Wireless router with WPS function is
auto-negotiate network client authentication.
1
Reset Button
There are two ways to reset the router's factory defaults:
1) Use the Factory Defaults function on Management -> Save/Reload
Settings page in the router's Web-based Utility.
2) Use the Factory Default Reset button: W ith the router powered on,
use a pin to press and hold the Reset button (about 6 seconds) until the
LED flash once. And then release the button and wait the router to reboot
to its factory default settings.
Configuring the Router
In the IE browser, type "192.168.2.1" into the login screen.
Enter you username and password, the default us ername is "admin",
and the default password is "admin".
After your successful login, you can see the interface as follows:
2
You can configure and manage the router. To apply any settings you
have altered on the page; please click the Apply Change button.
1 TCP/IP SETUP
1.1 LAN Setup
The LAN on this page to set the relevant parameters, click Apply;
3
IP Address: The Router’s LAN IP addresses (not your PC’s IP
address). 192.168.2.1 is the default value.
Subnet Mask: It’s shown the Router’s subnet mask for
measurement of the network size. 255.255.255.0 is the default value.
DNS Relay: The default value is Enable.
LAN SPEED: The default value is AUTO.
Notice:
Once you modify the IP address, you need to remember it for the
Web-based Utility login next time.
1.2 DHCP Setup
In the Page Setup DHCP, and set the range, click Apply;
4
DHCP Server: DHCP type is Enable and Disable. The default value
is Enable.
Starting IP address: Specify an IP address for the DHCP Server to
start with when assigning IP addresses. 192.168.2.100 is the default
start address
Ending IP address: Specify an IP address for the DHCP Server to end
with when assigning IP addresses. 192.168.2.200 is the default end
address;
Lease Time: The Address Lease Time is the amount of time a
network user will be allowed connection to the Router with their current
dynamic IP Address. Enter the amount of time in days and the user will
be "leased" this dynamic IP Address. After the time is up, the user will
be automatically assigned a new dynamic IP address. The default
value is 1 day.
Static DHCP: If you select Enable, you can set the client's IP address
5
and MAC address binding together.
1.3 WAN Setup
1.3.1 DHCP Mode
In the Page Setup WAN port connection type is DHCP, click Apply;
1.3.2 Static Mode
In the Page Setup WAN port connection type is static IP, IP address,
gateway address, DNS must be in accordance in front of the actual grid
environment settings, click Apply;
6
IP Address: Input ISP provide IP address
Subnet Mask: Input the corresponding subnet mask
ISP Gateway: Input ISP provide Gateway address
MAC Address: Input clone MAC address (optional)。
Primary DNS Address: Input ISP provide DNS address；
Secondary DNS Address: Input ISP secondary DNS address；
(optional)
1.3.3 PPPoE Mode
In the Page Setup WAN port connection type is PPPoE, please enter
your local ISP to provide the user ID and password, and click Apply.
7
Loading...