
RACK-UP® SERIES
TWISTED PAIR FORMAT-A
Model RU-TPDA
Four Output Format-A Distributor
Input Jack Accepts Signals from All FORMAT-A Senders
Output Jacks Drive All FORMAT-A Receivers
Four Receivers may be Driven From Each Distributor
LOOP OUT Jack Can Feed Additional Distributor
Power Bus Provides Expansion to Adjacent Distributors
Powers All Connected Senders and Receivers
Dual-LED VU Meters Display the Level on Each Pair
Blue Power LED Shows the Module is Receiving dc Power
Rear-Panel LEDs Indicate Correct Output Voltage on RJ45s
RDL FORMAT-A features superior audio performance that rivals or exceeds shielded wiring. Design simplicity, ease of installation, unsurpassed
flexibility, automatic fused power, exceptional hum rejection, low noise, and low distortion provide designers and installers the optimum choice in
economical twisted pair products.
APPLICATION: The RU-TPDA is a four output signal and power distributor module compatible with RDL
Format-A twisted pair products. The INPUT RJ45 jack accepts a twisted pair cable originating from one or
multiple FORMAT-A senders. The LOOP OUT connector permits the input signal to daisy-chain to
additional distributor modules. The RU-TPDA input circuits bridge the cable pairs, allowing up to 10
distributors to be connected together to produce 40 distributed outputs. Further expansion is possible by
using one distributor output to drive up to an additional 10 distributors. Three RDL Dual-LED VU meters
are provided on the front panel of the RU-TPDA. One meter monitors the audio level on each of the three
FORMAT-A audio pairs.
The RU-TPDA is constructed in the durable MAX RACK-UP chassis which facilitates mounting three
distributors in a single rack unit. A wide variety of mounting accessories are available in the RDL
RACK-UP series. A power bus in each RU-TPDA allows power to enter one module at either side of the
rack. The included power jumper cable provides a simple method of interconnecting one distributor
module to the next, so multiple modules can be operated from a single power supply.
The RU-TPDA is powered directly from a 24 Vdc power supply using either one of the power jacks or the
detachable terminal block. Local power connected to the module is also fed to all modules connected to
the INPUT and OUTPUT RJ45 jacks. The power feeding each OUTPUT jack is separately protected by an
automatically resetting fuse. A power LED is associated with each OUTPUT jack, facilitating identification
of wiring faults. Module power is indicated by a front-panel LED.
RDL 659 6th St. Prescott, AZ., USA 86301 (928) 443-9391 FAX (928) 443-9392 www.rdlnet.com

RACK-UP® SERIES
Twisted Pair FORMAT-A
Model RU-TPDA
Four Output Format-A Distributor
Note: The RU-TPDA provides power to all connected senders and receivers.
Installation/Operation
Declaration of Conformity available from rdlnet.com.
Sole EMC specifications provided on product package.
Specifications are subject to change without notice.
Pair A: Audio +4 dBu
Pair B: Audio +4 dBu
Pair C: Audio +4 dBu
Pair D: Power +24 Vdc
TYPICAL PERFORMANCE:
Input: RDL TP Format-A
Input Connection: RJ45
Format-A Signal Pairs Used (3): A, B, C
Format-A Output: RJ45 LOOP OUT
Outputs (4): RDL TP Format-A
Output Connection: RJ45
Frequency Response: 10 Hz to 50 kHz (+/- 0.1 dB)
THD+N: < 0.005%
RJ45 conductor colors shown are for 568A standard. The 568B standard m ay be used if the connectors at both ends of the cable are wired identically.
Radio Design Labs Technical Support Centers
U.S.A. (800) 933-1780, (928) 778-3554; Fax: (928) 778-3506
891-3245D
Europe [NH Amsterdam] (++31) 20-6238 983; Fax: (++31) 20-6225-287
RJ45 Standard wiring
(1) + White / Green
(2) – Green
(3) + White / Orange
(4) – Blue
(5) + White / Blue
(6) – Orange
(7) + White / Brown
(8) – Brown
Tab on bottom of connector
Noise below +4 dBu: < 90 dB
Crosstalk: < 90 dB (1 kHz); < 75 dB (20 Hz to 20 kHz)
Headroom above +4 dBu: > 18 dB
CMRR: > 80 dB (50 Hz to 150 Hz)
Indicators (11): Power In (1); Power Out (4); 3 Dual-LED VU Meters (6)
Power Connections (3): Power Jack (2); Detachable Terminal Block
Power Requirement: 24 Vdc @ 120 mA plus connected loads
Maximum Load Current: 200 mA (each RJ45 output)
Dimensions: 5.8" (15 cm) W; 1.7" (4.3 cm) H; 3.25" (8.25 cm) D