RDL FP-VDA4 User Manual

FLAT-PAK
SERIES
Model FP-VDA4 Video Distribution Amplifier
ANYWHERE YOU NEED...
Video Distribution with Four Outputs
Adjustable Gain
Input Loop-Through Jack
Wide Bandwidth – Flat to 10 MHz
NTSC or PAL Operation
Ultra-Compact All Metal Construction
Convenience of RDL FLAT-PAKs
You Need The FP-VDA4!
The FP-VDA4 is part of the group of versatile FLAT-PAK products from Radio Design Labs. The durable adhesives provided with the FP-VDA4 permit permanent or removable mounting. The unique FLAT-PAK case can also be directly screwed or bolted to cabinets or shelves. Optionally available rack-mounting accessories permit single or multiple FLAT-PAK module mounting. All FLAT-PAK modules are supplied with a power interconnect cable for daisy-chaining multiple modules from a single power supply.
APPLICATION: The FP-VDA4 is the ideal choice in many applications where video signals need to be distributed. Video input and output connections are made on the top panel BNC jacks. Power connections are made using either the full-size barrier block terminals or a dc power jack located in one end panel. A second dc power jack is provided on the other end panel for connecting additional FLAT­PAK modules.
The FP-VDA4 has two jacks in the bridging input stage. One jack is for the input signal; the other is a loop-through output of the source signal. If 75 Ω termination of the input signal is required, the terminator (provided) is plugged onto the Loop Out jack. Gain is user adjustable from the top panel. The gain potentiometer allows adjustment from unity to +6 dB. Four source-terminated outputs are provided through the BNC output jacks. Unused outputs need not be terminated.
The FP-VDA4’s low profile and compact size permit mounting in confined spaces and in various locations in equipment racks. The location of the input/output jacks permits high density mounting against flat surfaces while maintaining accessibility to the connectors. Installations requiring multiple distribution amplifiers are ideally designed using FP-VDA4s affixed to rack sides, or by mounting them to either the front or rear rack rails using the RDL FP-RRA.
Wherever a video distribution amplifier is needed to provide wide-band video feeds, gain adjustment, reliability, compactness and unsurpassed versatility, the FP-VDA4 is the ideal choice. Use the FP-VDA4 individually, or combine it with other RDL products as part of a complete audio/video system.
DTS2020 Typical Performance reflects product at publication time exclusive of EMC data, if any, supplied with product. Specifications subject to change without notice.
Video Source Feeding
FP-VDA4 Input
FP-VDA4
Typical Connections
2A MAX
INPUT
INPUT OUTPUT 2
OUTPUT 1
Video Output Feeding
Other Video Equipment
60 mA
FP-VDA4
CURRENT
OUTPUT
PWR BUS
Power to Additional
Flat-Pak Modules, Total
Current Not to Exceed 2 A
or Available Supply Current
OR
24 VDC
POWER
SOURCE
POWER
24 VDC
LOOP
OUT OUTPUT 4OUTPUT 3
1A MAX
INPUT
Video Loop Out Feeding
Other Video Equipment, or
use 75 Ohm Terminator
GAIN
UNITY GAIN
Unity Gain is Set with
Control Fully
Counter-Clockwise,
Turning Control Clockwise
Increases Gain
TYPICAL PERFORMANCE
Input Impedance: 1 k (Bridging 75 Line) Gain Range: Unity to +6 dB (adjustable) Load Impedance: 75 Outputs (5): 1 Loop Out from Input Signal; 4 Amplified Outputs Output Level: 1 V p-p (into 75 ) Frequency Response: 10 Hz - 10 MHz (+/- 0.2 dB) Noise: < -75 dB (below 1 V p-p) Output Isolation: > 45 dB Differential Gain: 0.1% Differential Phase: 0.1 degree (measured at 10% and 90% APL) Connector Type: BNC Power Requirement: 24 Vdc @ 60 mA, Ground-referenced Dimensions: Height: 0.88 in. 2.24 cm (not including connectors) Height: 1.35 in. 3.43 cm (including connectors) Width: 3.25 in. 8.26 cm Length: 4.20 in. 10.67 cm
EMC:
RDL •• P.O. Box 1286 •• Carpinteria, CA., USA 93014 •• (805) 684-5415 •• FAX (805) 684-9316 •• Fax-on-Demand (800) 391-0017 •• http://www.rdlnet.com
Loading...