
™
FLAT-PAK
SERIES
Model FP-UBC2
Unbalanced to Balanced
Converter
ANYWHERE YOU NEED...
• Stereo Unbalanced to Balanced
Audio Conversion
• Connectorized Audio Converter
• Low Noise and Distortion
• Cabinet, Shelf or Rack Mounting
• Convenience of RDL FLAT-PAKs
You Need The FP-UBC2!
The FP-UBC2 is part of the group of versatile FLAT-PAK products from Radio Design Labs. The unique
FLAT-PAK case can be directly screwed or bolted to cabinets or shelves. Optionally available rackmounting accessories permit single or multiple FLAT-PAK module mounting. All FLAT-PAK modules are
supplied with a power interconnect cable for daisy-chaining multiple modules from a single power supply.
APPLICATION: The FP-UBC2 is the ideal choice for connectorized conversion from unbalanced to
balanced audio. This module features two identical channels. Gold-plated phono jacks are utilized for
each unbalanced input channel. Each output is balanced, connected through an XLR jack. A gain trim
potentiometer is provided for each channel.
The normal gain setting is indicated for the trimming potentiometer. This setting produces a +4 dBu
balanced output for a –10 dBV unbalanced input. The gain is adjustable –5 dB to +10 dB from the normal
gain. Therefore, a +4 dBu output signal is possible from input signals ranging from –20 dBV to –5 dBV.
The FP-UBC2 circuitry features low noise, low distortion, excellent headroom and crosstalk performance
and the superior audio clarity for which RDL products are known.
Power may be connected to the FP-UBC2 through either a terminal block or a dc power input jack. The
input voltage to the module is carried through to an output dc jack permitting additional modules to be
powered from the same power supply.
Wherever convenient, economical, high performance, connectorized two-channel audio format conversion
is required, the FP-UBC2 is the ideal choice. Use the FP-UBC2 individually, or combine it with other RDL
RACK-UP
®
, STICK-ON®, TX™, or FLAT-PAK series products as part of a complete audio/video system.
RDL • 659 N. 6th St. • Prescott, AZ., USA 86301 • (928) 443-9391 • FAX (928) 443-9392 • www.rdlnet.com

™
FLAT-PAK
SERIES
Model FP-UBC2
Unbalanced to Balanced Converter
Installation/Operation
EN55103-1 E1-E5; EN55103-2 E1-E4
Typical Performance reflects product at publication time
exclusive of EMC data, if any, supplied with product.
Specifications are subject to change without notice.
OR
24 VDC
POWER
SOURCE
Unbalanced Audio
Source Feeding
FP-UBC2 Input
2A MAX
INPUT
INPUT 1
POWER
24 VDC
1A MAX
INPUT
GAIN
OUTPUT 1
INPUT 2
GAIN
OUTPUT 2
50 mA
FP-UBC2
CURRENT
OUTPUT
PWR BUS
Balanced Audio Outputs
Feeding Other Balanced
Audio Equipment
Gain ShownSet
for +4 dBu Output
From A -10 dBV
Input
Power to Additional
Flat-Pak Modules, Total
Current Not to Exceed 2 A
or Available Supply Current
TYPICAL PERFORMANCE
Amps per FP-UBC2: 2 identical circuits (stereo or dual mono operation)
Gain: -5 dB to +10 dB adjustable (relative to +4 dBu output for –10 dBV input);
(separate controls for each channel)
Input level: -20 dBV to -5 dBV (for +4 dBu output)
Input impedance: 10 kΩ
Input configuration: Unbalanced
Output impedance: 150 Ω balanced, drives 600 Ω or 10 kΩ lines
Output configuration: Balanced or unbalanced
Frequency Response: 20 Hz to 40 kHz (+/- 0.25 dB)
THD+N: < 0.05%; typ. 0.01% (1 kHz)
IMD: < 0.02%
Output Level: +4 dBu
Headroom: > 18 dB (at rated output level of +4 dBu)
Noise: < -85 dB referred to +4 dBu (20 Hz to 20 kHz)
Crosstalk: Better than -70 dB (20 Hz to 20 kHz); typ <-80 dB (1 kHz)
Power Requirement: 24 Vdc @ 50 mA, Ground-referenced
Overall Dimensions: Height: 1.29 in. 3.28 cm
Width: 3.25 in. 8.26 cm
Length: 4.07 in. 10.34 cm
Radio Design Labs Technical Support Centers
U.S.A. (800) 933-1780, (928) 778-3554; Fax: (928) 778-3506
891-2025F
Europe [NH Amsterdam] (++31) 20-6238 983; Fax: (++31) 20-6225-287