Page 1
INSTALLATION
MANUAL
EZ-DC1 and EZ-DC2
Desktop Chassis
Model EZ-DC1
1/6 Rack width
Model EZ-DC2
1/3 Rack width
RDL EZ Series products provide the highest level of value to A/V professionals and A/V users who demand professional quality.
For long-term performance, quality and value, you have made the EZ choice. EZ products are made in the USA by RDL, the
inventor of application-specific modules bringing decades of experience as the world’s leading manufacturer of high-reliability
performance products to the A/V industry. Visit the RDL website for hundreds of professional A/V products made in the USA by RDL.
www.rdlnet.com
Decades of Performance, Quality and Value
RDL• 659 N. 6th Street • Prescott, AZ • USA 86301 • Sales: 800-281-2683 • 928-443-9391
Tech Support: 800-933-1780 • 928-778-3554 • RDL Europe Sales & Support: (31) 20-6238-983
Page 2
EZ-DC1 and EZ-DC2
Desktop Chassis
•
Mounts 1/6 Width (EZ-DC1) or 1/3 Width (EZ-DC2) EZ Product to Desktop
•
Installs Quickly With Two Screws
•
Covers Cable Port in Desktop
•
Provides Space for Excess Wire
FEATURES OF EZ-DC MODELS
CHASSIS TOP VIEW
Features are common to both models.
UPPER OPENING
The top of the chassis is open to provide convenient
access for fastening the chassis to the desktop and
for pulling wires through the desktop.
BOTTOM WIRE INLET
The bottom of the chassis is open to provide a
large area for locating a clearance hole for wires to
pass through the desktop.
REAR WIRE INLET
The rear of the chassis is open to provide wiring
access to the back of the EZ product.
MOUNTING HOLES
These holes are used to mount a 5” (12.7 cm)
deep EZ product to an EZ-DC.
MOUNTING HOLES
These holes are used to mount a 3” (7.6 cm) deep EZ product to an EZ-DC.
www.rdlnet.com • • • www.rdlez.com
Page 3
MOUNTING EZ-DC MODELS
STEP 1
Fasten chassis into position on the desktop after drilling a wire access hole in the desktop and
pulling the wires through. Route the wires out the rear of the chassis while mounting.
CHASSIS BOTTOM VIEW
DESKTOP OR TABLETOP MOUNTING SURFACE
STEP 2
Mount the EZ product to the chassis using two screws.
EZ-DC2 WITH AN EZ PRODUCT MOUNTED
Page 4
OTHER SELECTED EZ SERIES MOUNTING ACCESSORIES
EZ-RA6
Rack Adapter for 6 Increments of 1/6 Rack Width
EZ-CC6
Component Chassis for 6 Increments of 1/6 Rack Width
EZ-SMB1
Surface Mount Bezel for 1/6 Rack Width Products
EZ-SD1
Storage Drawer 1/6 Rack Width
Use EZ-SD1 and EZ-SD2 in Place of Filler Panel(s)
Drawers
Hold Adapters and Cables
Mount in EZ-CC6 and EZ-RA6
EZ-UCB2
Under-Counter Brackets 1/6 or 1/3 Rack Width
EZ-SMB2
Surface Mount Bezel for 1/3 Rack Width Products
EZ-SD2
Storage Drawer 1/3 Rack Width
EZ-FP1
Filler Panel 1/6 Rack Width
Mounts in EZ-CC6 and EZ-RA6
Complete accessory listing available at: rdlez.com
Copyright © 2009 Radio Design Labs, Inc. RDL, Radio Design Labs and the RDL logo are registered trademarks of Radio Design Labs, Inc. Data reflects product at publication time, subject to change without notice. “Made in USA” applies to all EZ products except power supplies.
891-1625
Loading...