RDL DB-RT2, D-RT2, DS-RT2 Datasheet

ACCESSORIES

Models D-RT2, DS-RT2, DB-RT2

Remote Control Selector

i i i

 Remote Selection of ON or OFF
 Single-Button Selection for Each Function
 Open -collector Switching
 Rear Panel Connections on Detachable Terminal Block

The D SERIES-RT2 is part of the group of versatile wall-mounted products from Radio Design Labs. The standard mounting case can be directly fastened in North
American electrical boxes or in RDL International wall boxes.

DB-RT2

DS-RT2

D-RT2

 3-wire or 4- wire Remote Wiring
 Professional Aesthetic Appearance
 Ultra-Compact All Metal Construction
 LED Indication

APPLICATION: The D SERIES-RT2 is part of the RDL accessories group and is designed as a functional and visual

complement to many other RDL remote controls such as the D-RLC2, D-RLC3 or D-RLC10K Remote Level Controls.

The -RT2 is a wall-box mounted remote module designed to directly control equipment which utilizes pull-to-ground
switching.

The front panel of the -RT2 features two pushbuttons with two associated LEDs. Upon initial power-up, the OFF mode is
selected. Touching the other button de-selects OFF and immediately selects ON. An LED adjacent to each button shows
which mode is selected.

In a typical installation, the -RT2 may be used to turn an audio or video source on or off. To turn on an audio source, the

-RT2 may be connected to an RDL ST-SSR1 or ST-RX2 Solid-State Audio Switch. For video switching, an RDL TX-MVX
may be used. In each of the above examples, only one output terminal is needed for triggering, therefore a single shielded
pair (3-conductor cable) is required for remote connection. For more complex switching networks, both outputs (ON and
OFF) may be used. In an audio or video control installation, the -RT2 may be mounted adjacent to an RDL remote volume
control, such as the D-RLC2, D-RLC3 or D-RLC10K.

In an installation where a wall-mounted remote control is needed to power up a system or subsystem, the -RT2 may be
connected to the control terminal of the RU-SQ6A Power-Up Sequencer. Other RDL modules using open-collector input
switching may be connected to the -RT2, such as the STM-2X. In this case, the -RT2 provides a remote off/on switching of
a mic.

The -RT2 is constructed on a durable polycarbonate-faced, powder-coated steel panel. Electronics are housed in a metal
enclosure featuring a rear panel detachable terminal block for easy wiring. The attractive front-panel graphics and quality
construction make the RT2 the ideal choice in any high quality and economical wall-mounted remote control installation.

In installations where ULTRASTYLE™ wall controls are preferred, use the RUC-4 Universal Remote. The -RT2 is part of
the RDL accessories group and is designed as a functional and visual complement to many other RDL remote controls
such as the D-RLC2, D-RLC3 or D-RLC10K Remote Level Controls.

RDL  659 N. 6th St.  Prescott, AZ., USA 86301  [phone]  FAX [phone]  www.rdlnet.com

ACCESSORIES

Models D-RT2, DS-RT2, DB-RT2

Remote Control Selector

Mounting
The D SERIES–RT2 should be mounted in an RDL WB-1U wall box or equivalent. The ambient operating environment must not exceed 40 degrees C.

Installation/Operation

EN55103-1 E1-E5; EN55103-2 E1-E4; EN60065

Typical Performance reflects product at publication tim e exclusive of EMC
data, if any, supplied with product. Specifications are subject to change
without notice. This product is Professional Apparatus.

TYPICAL PERFORMANCE

Selectors: 2 Momentary Pushbuttons, 1 for ON, 1 for OFF
Indicators: 2 LEDs, Indicates status ON or OFF
Connections: Power input; Separate Open-collector outputs
for ON and OFF (25 mA)
Power Requirement: 24 to 33 Vdc @ 30 mA, Ground-referenced
Mounting: Mounts in US standard electrical box,
decorative plate available separately

Dimensions: Height: 4.11 in. (10.4 cm)
Depth: 1.66 in. (4.21 cm)
Width: 1.72 in. (4.37 cm)

Radio Design Labs Technical Support Centers

U.S.A. [phone], [phone]; Fax: [phone]

891-5575

Europe [NH Amsterdam] (++31) 20-6238 983; Fax: (++31) 20-6225-287