RCS RCS-433MDR1 User Manual
RCS-433MDR1
Thank you for choosing a RCS transmitter. It is recommended
you read this manual carefully before using the transmitter.
that
CONTENTS
1 - TRANSMITTER INTRODUCTION
- General Information
1A
- Technical Specifications
1B
- Main Features
1C
- Model Types
1D
2 - CODING
3 - MEMORIZATION
4 - BATTERY AND DIP-SWITCH ACCESS
5 - TROUBLESHOOTING
USER
MANUAL
1 - TRANSMITTER INTRODUCTION
1A - General Information
• The radio control, RCS- 433MDR1 has been designed for the
control of automatic closing systems and anti-burglar systems.
The operating frequency is 433.92 MHz.
• The transmitter security code is obtained by means of a
10
way three-state dip-switch, which allows up to 19683 codes
combinations.
• Each transmitter (or its different keys) can be stored into
di
fferent receivers and hence can do more functions.
• The product fully complies with Part 15 of FCC Regulations.
- Technical specifications
1B
of keys: . . . . . . . . . . . . . . . . . . . . . . . . . .1
Number
duration: . . . . . . . . . . . . . . . . . .12 - 24 months
Battery
type: . . . . . . . . . . . . . . . . . . . . . . . .23A (L1028)
Battery
Current consumption: . . . . . . . . . . . . . . . . . . . . .25 mA
Operating frequency: . . . . . . . . . . . . . . . . .433.92 MHz
code combinations number: . . . . . . . . .19683
Security
Modulation: . . . . . . . . . . . . . . . . . . . . . . . . . . .AM/ASK
r.p.: . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50 - 100 uW
E.
in open space: . . . . . . . . . . .from 100 to 200 m
Range
Operating temperature: . . . . . . .from -10 °C to +55 °C
Dimensions: . . . . . . . . . . . . . . . . . . . . .1.75 x 1 x .3 in.
Weight: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ..7 oz.
1C - Main Features
Red LED
Button
- Model Types
1D
1 button dip-switch transmitter: Model #: RCS-433MDR1
2 - CODING
Using a coin, insert and twist to access to the battery and the
dip-switches. The
Warning:Each transmitter is set-in-factory with the same code on
dip-switches; it highly advisable to change this code by moving
the
the
dip-switches to any random position ( “+”, “0” , “-”).
3 - MEMORIZATION
Each dip-switch setting code has to be stored into the receiver
y. The memorization can be done by self-learning. The
memor
instructions
manual.
installation or will give you the necessary explanation
the
installation.
during
This device complies with Part 15 of the FCC Rules.
This device may not cause harmful interferences; and
1)
2) this device must accept any interference received, including interference that may cause undesired operation
Notice:Any changes or modification to RCS equipment not
expressly approved by RCS could void the user's authority to
operate the equipment.
dip-position will give the security code.
for this operation is given on the receiver installation
Your own installer will perform this operation during
RCS-433MDR1 FCC ID: TG6RCS433MDR
following two conditions:
Operation is subject to the
4 - BATTERY AND DIP-SWITCH ACCESS
To access the battery, Using a coin, insert
and twist. Place
battery
Respect
on
the bottom of the box.
NOTE:Please dispose of the battery
rectly, they are hazardous waste.
cor
5 - TROUBLESHOOTING
the 23A alkaline
between the 2 contacts.
the right polarity as indicated
Battery
Dip-Switch
The radio signal is not verifiable Replace the transmitter battery
transmitter led doesn't switch on Replace the transmitter battery
The
The
radio signal is not verifiable Check the power supply of
the receiver
The transmitter led switches on Replace the transmitter battery
GUARANTEE
guarantee period of all RCS transmitters is 12 months,
The
the
from the manufacturer date. During this period,
beginning
the product does not work correctly, due to a defective
if
component,
at
the discretion of RCS. The guarantee does not cover
plastic container integrity. After-sale service is supplied
the product will be repaired or substituted
the producer's factory.
at
CONTROL SOLUTIONS, LLC
REMOTE
1-866-770-0727
ww
w.rcsremotes.com
Loading...