RCS EP3110, EP3115, EP3122, EP3125, EP3116 Installation & User Manual

The ETL Symbol is a UK registered certification mark of the

Department of Energy and Climate Change

Authorised User: 03195

Installation & User Guide

Eden Power Tray

Installation Guide | Issue 2.0 | The Eden Power Tray Page 1

Contents

The Eden Power Tray

Contents

1. INTRODUCTION 4

1.1 The Eden Power Tray Range 4

1.1.1 Variants / Part Codes for Ordering 5

1.1.2 Replacing Legacy Equipment 6

1.1.3 Eden Power Tray – Mating Connectors 6

2. CONNECTION DETAILS 7

2.1 EP3115 & 3116 10A Assisted Defrost / Major Tray Connectivity 7

2.2 EP3115 & 3116 10A Assisted Defrost / Major Tray Circuit Diagram 8

2.3 EP3113 & 3114 30A Assisted Defrost / KTUC09Tray Connectivity 9

2.4 EP3113 & 3114 30A Assisted Defrost / KTUC09Tray Circuit Diagram 10

2.5 EP3119 & 31110 Hot Gas Defrost / KTUC09 HG Tray Connectivity 11

2.6 EP3119 / 31110 Hot Gas Defrost / KTUC09 HG Tray Circuit Diagram 12

2.7 EP3117 & EP3118 External Defrost Contactor / KTUC09 Tray Connectivity 13

2.8 EP3117 & EP3118 External Defrost Contactor / KTUC09 Tray Circuit Diagram 14

2.9 EP3111 Minor Assisted Defrost Tray Connectivity 15

2.10 EP3111 Minor Assisted Defrost Tray Circuit Diagram 16

2.11 EP3110 & 3112 Off-Cycle Defrost Tray Connectivity 17

2.12 EP3110 & 3112 Off-Cycle Defrost Tray Circuit Diagram 18

2.13 All Variants – Sensor / Communication Network Connections 19

2.14 All Variants – Tray End View 20

3. SETTING THE CONTROLLER UP 21

3.1 Front panel display keys & icons 21

3.2 Using the front panel display & function keys 23

3.2.1 Set up menu 24

3.2.2 Controllers address & communications menu 26

3.2.3 Controllers refrigeration related parameter menu 28

3.2.4 Controllers defrost menu 30

3.2.5 Controllers fan related parameter menu 32

3.2.6 Controllers times related parameter menu 34

3.2.7 Controllers current status menu 36

3.2.8 Controllers current alarms menu 38

3.2.9 Controllers lights related parameter menu 40

3.2.10 Controllers sleep mode menu 41

3.2.11 Controllers self test menu 42

4. CLEANING INSTRUCTIONS 43

5. SPECIFICATION 44

5.1 Power requirements 44

5.2 Dimensions 44

5.3 Inputs 44

5.4 Communications 44

Installation Guide | Issue 2.0 | The Eden Power Tray Page 2

Contents

The Eden Power Tray

6. REVISION HISTORY 45

7. DISCLAIMER 46

8. CONTACT DETAILS 47

9. APPENDICES 48

9.1 Cycle Time function (Times menu (Ti13) ` 48

9.2 Defrost Cycle (Fans Off) 49

9.3 Defrost Cycle (Fans On) 50

9.4 Integral Compressor Action 51

9.5 Remote Display 52

9.5.1 Panel Cut-out 52

9.5.2 Remote Display 53

9.5.3 Retaining Clips 53

9.5.4 Remote Display Module 53

10. EUROPEAN DECLARATION OF CONFORMITY 54

Installation Guide | Issue 2.0 | The Eden Power Tray Page 3

Introduction

The Eden Power Tray

1. Introduction

The Eden Power Tray series of products are a range of complete refrigerated cabinet control solutions. The extensive range provides prewired control panels suitable for both new installations and replacement of legacy products. All of which utilise the intuitive RCS Eden Compact controller.

Each of the variants in the range delivers a powerful combination of connectivity, flexibility and ease of use in a gear tray capable of safely supplying all required cabinet loads.

The Eden Power Tray range offers quality, high performance case control which will encompass and satisfy the most stringent of refrigerated cabinet applications.

1.1 The Eden power Tray Range

All high current outputs are protected by re-settable MCB’s. Connector configurations where possible remain identical to previous RCS cabinet control panels to safeguard easy replacement of legacy units. The assisted defrost variants also provide an external connection for defrost heater klixons to provide further safety features.

The Eden Compact controller incorporated into each of the power tray variants was designed as the first all-inone compact refrigeration controller requiring no additional communication modules. The Eden Compact provides easy configuration and the ability to set custom parameter sets.

The Eden Compact series covers the full range of evaporator inlet valve type and network connectivity options. The user must choose at the point of ordering which of the following two basic options are required:-

Network compatibility

 IP  RS485

Inlet Valve Type

 LSV  EEV

Each model is easy to install and configure, thanks to features such as the standard two-part connectors for all external wiring of Inputs/Outputs. All Eden Compact controllers provide the option of up to seven temperature / analogue inputs for maximum flexibility, and multiple sensor types are also supported. (NB sensor types cannot be mixed on a single controller).

Installation Guide | Issue 2.0 | The Eden Power Tray Page 4

Part Codes

The Eden Power Tray

Variant

Inlet Valve Type

Communication Type

Part No

Off-Cycle defrost

LSV

RS485

EP3110

Off-Cycle defrost

EEV

RS485

EP3112

Off-Cycle defrost

LSV

IP

EP3120

Off-Cycle defrost

EEV

IP

EP3122

10A Assisted defrost

LSV

RS485

EP3115

10A Assisted defrost

EEV

RS485

EP3116

10A Assisted defrost

LSV

IP

EP3125

10A Assisted defrost

EEV

IP

EP3126

30A Assisted defrost

LSV

RS485

EP3113

30A Assisted defrost

EEV

RS485

EP3114

30A Assisted defrost

LSV

IP

EP3123

30A Assisted defrost

EEV

IP

EP3124

External Defrost contactor

LSV

RS485

EP3117

External Defrost contactor

EEV

RS485

EP3118

External Defrost contactor

LSV

IP

EP3127

External Defrost contactor

EEV

IP

EP3128

Hot Gas defrost

LSV

RS485

EP3119

Hot Gas defrost

EEV

RS485

EP31110

Hot Gas defrost

LSV

IP

EP3129

Hot Gas defrost

EEV

IP

EP31210

1.1.1 Variants / Part Codes for Ordering

This installation and set-up guide covers the complete Eden Power Tray range. The following part codes should be used at the ordering stage:-

Remote display variants of each of the above are also available.

Please refer to each of the connection details and circuit drawings within this document to establish maximum ratings for outputs for each variant.

Please note that warranty is void if any Eden power tray is used in any application that does not conform to the tray specification.

Installation Guide | Issue 2.0 | The Eden Power Tray Page 5

Legacy Part Codes

The Eden Power Tray

Part Number

Replacement For

EP3115 (LSV)

Major Assisted Defrost

EP3116 (EEV)

Major Assisted Defrost

EP3113 (LSV)

KTUC09 Assisted Defrost (Electric)

EP3114 (EEV)

KTUC09 Assisted Defrost (Electric)

EP3119 (LSV)

KTUC09 Hot Gas Defrost

EP31110 (EEV)

KTUC09 Hot Gas Defrost

EP3117 (LSV)

KTUC09 Tray (External Contactor)

EP3118 (EEV)

KTUC09 Tray (External Contactor)

EP3111 (LSV Only)

Minor Assisted Defrost

EP3110 (LSV)

Off-Cycle Defrost - ALL VARIANTS

EP3112 (EEV)

Off-Cycle Defrost – ALL VARIANTS

1.1.2 Replacing Legacy Equipment

The following part codes should be used at the ordering stage when replacing previous Powertray models:

1.1.3 Power Tray Mating Connectors

Eden Power Tray Mating Connectors:-

 Incoming Mains Supply Connector, mates with: Weidmuller STVS3 161699 RCS Part Code KS3STVS00

 Cable Clamp / Strain Relief for above connector: Weidmuller STVS3ZE 161387. RCS Part Code K00STV3ZE

 STV1 / 2, mates with: Weidmuller STVS3 174367. RCS Part Code KP10STVS00

 Cable Clamp / Strain Relief for above connector: weidmuller STVS10ZE 161394. RCS Part Code K010STV10ZE

 Sensor / 485 Connector, mates with: Weidmuller BL12 126026 RCS Part Code KS12BL00

 Klixon (Loop Back) RCS Part Code 300-00238

Installation Guide | Issue 2.0 | The Eden Power Tray Page 6

Connection Details – 10A Assisted Defrost

The Eden Power Tray

2. Connection Details

Pin Number

Function

Rating/Designation

1

Earth

2 Defrost Live

10A Internal MCB (CB 2)

3

Defrost Neutral

4

LSV/EEV Live

2A Internal MCB (CB 8)

5

LSV/EEV Neutral

6

Fans Live

4A Internal MCB (CB 9)

7

Fans Neutral

8

Lights Live

6A Internal MCB (CB 5)

9

Lights Neutral

10

Earth

Pin Number

Function

Rating/Designation

1

Earth

2 Suction Live

2A Internal MCB (CB7)

3

Suction Neutral

4 Not Used

5 Not Used

6 Not Used

7

Not Used

8

Trim Heater Live

10A Internal MCB (CB 6)

9

Trim Heater Neutral

10

Earth

Pin Number

Function

Rating Designation

1 Unit Supplied with loop fitted

2

2.1 EP3115, EP3125 (LSV) & EP3116, EP3126 (EEV)

(10A Assisted Defrost & Major Legacy replacement) - Connectivity Details

STV1

STV2

Defrost Safety Klixon

Eden controller power is supplied via an internal 2A MCB (CB 1)

Installation Guide | Issue 2.0 | The Eden Power Tray Page 7

10A Assisted Defrost Circuit Diagram

The Eden Power Tray

2.2 EP3115, EP3125 (LSV) & EP3116, EP3126 (EEV)

(10A Assisted Defrost & Major Legacy replacement) -Circuit Diagram

Installation Guide | Issue 2.0 | The Eden Power Tray Page 8

Connection Details - 30A Assisted Defrost

The Eden Power Tray

2.3 EP3113, EP3123 (LSV) & EP3114, EP3124 (EEV)

Pin Number

Function

Rating/Designation

1

Earth

2

Defrost Live

10A Internal MCB (CB 2)

3

Defrost Neutral

4

LSV/EEV Live

2A Internal MCB (CB 8)

5

LSV/EEV Neutral

6

Fans Live

4A Internal MCB (CB 9)

7

Fans Neutral

8

Lights Live

6A Internal MCB (CB 5)

9

Lights Neutral

10

Earth

Pin Number

Function

Rating/Designation

1

Earth

2 Suction Live

2A Internal MCB (CB 7)

3

Suction Neutral

4 Defrost Live

10A Internal MCB (CB 3)

5

Defrost Neutral

6 Defrost Live

10A Internal MCB (CB 4)

7

Defrost Neutral

8

Trim Heater Live

10A Internal MCB (CB 6)

9

Trim Heater Neutral

10

Earth

Pin Number

Function

Rating Designation

1 Unit Supplied with loop fitted

2

(30A Assisted Defrost & KTUC09 Electric Defrost Legacy replacement) Connectivity Details

STV1

STV2

Defrost Safety Klixon

Eden controller power is supplied via an internal 2A MCB (CB 1)

Installation Guide | Issue 2.0 | The Eden Power Tray Page 9

30A Assisted Defrost Circuit Diagram

The Eden Power Tray

2.4 EP3113, EP3123 (LSV) & EP3114, EP3124 (EEV)

(30A Assisted Defrost & KTUC09 Electric Defrost Legacy replacement) – Circuit Diagram

Installation Guide | Issue 2.0 | The Eden Power Tray Page 10

Connection Details - Hot Gas Defrost

The Eden Power Tray

2.5 EP3119, EP3129 (LSV) & EP31110, EP31210 (EEV)

Pin Number

Function

Rating/Designation

1

Earth

2

Not Used

3

Not Used

4

LSV/EEV Live

2A Internal MCB (CB 8)

5

LSV/EEV Neutral

6

Fans Live

4A Internal MCB (CB 9)

7

Fans Neutral

8

Lights Live

6A Internal MCB (CB 5)

9

Lights Neutral

10

Earth

Pin Number

Function

Rating/Designation

1

Earth

2 Suction Live

2A Internal MCB (CB 7)

3

Suction Neutral

4 Hot Gas S/V Live

2A Internal MCB (CB 3)

5

Hot Gas S/V Neutral

6

Not Used

7

Not Used

8

Trim Heater Live

10A Internal MCB (CB 6)

9

Trim Heater Neutral

10

Earth

Pin Number

Function

Rating Designation

1 Unit Supplied with loop fitted

2

(Hot Gas Defrost & KTUC09 Hot Gas Defrost Legacy replacement) Connectivity Details

STV1

STV2

Defrost Safety Klixon

Eden controller power is supplied via an internal 2A MCB (CB 1)

Installation Guide | Issue 2.0 | The Eden Power Tray Page 11

Hot Gas Defrost Circuit Diagram

The Eden Power Tray

2.6 EP3119, EP3129 (LSV) & EP31110, EP31210 (EEV)

(Hot Gas Defrost & KTUC09 Hot Gas Defrost Legacy replacement) - Circuit Diagram

Installation Guide | Issue 2.0 | The Eden Power Tray Page 12

Connection Details - External Defrost Contactor

The Eden Power Tray

2.7 EP3117, EP3127 (LSV) & EP3118, EP3128 (EEV)

Pin Number

Function

Rating/Designation

1

Earth

2

Not Used

3

Not Used

4

LSV/EEV Live

2A Internal MCB (CB 8)

5

LSV/EEV Neutral

6

Fans Live

4A Internal MCB (CB 9)

7

Fans Neutral

8

Lights Live

6A Internal MCB (CB 5)

9

Lights Neutral

10

Earth

Pin Number

Function

Rating/Designation

1

Earth

2 Suction Live

2A Internal MCB (CB 7)

3

Suction Neutral

4 External Defrost Contactor Live

2A Internal MCB (CB 3)

5

External Defrost Contactor Neutral

6

Not Used

7

Not Used

8

Trim Heater Live

10A Internal MCB (CB 6)

9

Trim Heater Neutral

10

Earth

Pin Number

Function

Rating Designation

1 Unit Supplied with loop fitted

2

(External Defrost Contactor & KTUC09 “Tray” Legacy replacement) Connectivity Details

STV1

STV2

Defrost Safety Klixon

Eden controller power is supplied via an internal 2A MCB (CB 1)

Installation Guide | Issue 2.0 | The Eden Power Tray Page 13

External Defrost Contactor Circuit Diagram

The Eden Power Tray

2.8 EP3117, EP3127 (LSV) & EP3118, EP3128 (EEV)

(External Defrost Contactor & KTUC09 “Tray” Legacy replacement) – Circuit Diagram

Installation Guide | Issue 2.0 | The Eden Power Tray Page 14

Connection Details - Minor Assisted Defrost

The Eden Power Tray

2.9 EP3111 (Minor Assisted Defrost Legacy replacement) –

Pin Number

Function

Rating/Designation

1

Earth

2

Defrost Live

16A Internal MCB (CB4)

3

Defrost Neutral

4 LSV/EEV Live

2A Internal MCB (CB 6)

5

LSV/EEV Neutral

6 Fans Live

2A Internal MCB (CB 5)

7

Fans Neutral

8 Lights Live

6A Internal MCB (CB 3)

9

Lights Neutral

10

Earth

Pin Number

Function

Rating/Designation

1

Trim heater Live

6A Internal MCB (CB 2)

2

Trim Heater Earth

3

Trim Heater Neutral

Connectivity Details

STV1

Trim Heater STV

Eden controller power is supplied via an internal 2A MCB (CB 1)

Installation Guide | Issue 2.0 | The Eden Power Tray Page 15

Minor Assisted Defrost Circuit Diagram

The Eden Power Tray

2.10 EP3111 (Minor Assisted Defrost Legacy replacement) – Circuit Diagram

Installation Guide | Issue 2.0 | The Eden Power Tray Page 16

Connection Details – Off-Cycle Defrost

The Eden Power Tray

Pin Number

Function

Rating/Designation

1

Earth

2 Curtain Fan Live

4A Internal MCB (CB 3)

3

Curtain Fan Neutral

4 LSV/EEV Live

2A Internal MCB (CB 5)

5

LSV/EEV Neutral

6 Fans Live

4A Internal MCB (CB 4)

7

Fans Neutral

8 Lights Live

6A Internal MCB (CB 2)

9

Lights Neutral

10

Earth

2.11 EP3110, EP3120 (LSV) & EP3112, EP3122 (EEV) (Off-Cycle Defrost)

– Connectivity Details

STV1

Eden controller power is supplied via an internal 2A MCB (CB 1)

Installation Guide | Issue 2.0 | The Eden Power Tray Page 17

Off-Cycle Defrost Circuit Diagram

The Eden Power Tray

2.12 EP311, EP3120 (LSV) & EP3112, EP3122 (EEV) (Off-Cycle Defrost)

– Circuit Diagram

Installation Guide | Issue 2.0 | The Eden Power Tray Page 18

Connection Details – Sensors & Comms.

The Eden Power Tray

Pin Number

Function

Rating/Designation

1

Air On – Signal

2

Air On – Ground

3

Air Off Sensor – Signal

4

Air Off Sensor – Ground

5

Evaporator In Sensor – Signal

Optional (Set-up option – see section

3.2.1) SU11

6

Evaporator in Sensor – Ground

7

Evaporator Out Sensor – Signal

Optional (Set-up option – see section

3.2.1) SU11

8

Evaporator Out Sensor – Ground

9

Defrost Termination Sensor – Signal

Optional (Set-up option – see section

3.2.4) DF8

10

Defrost Termination Sensor – Ground

11

RS485 Communication Network -

Omitted if IP Variant

12

RS485 Communication Network +

2.13 All Variants – Sensor / communication network connections

12 Way BLZ

Installation Guide | Issue 2.0 | The Eden Power Tray Page 19

Chassis – End View

The Eden Power Tray

2.14 All Variants – End View

Installation Guide | Issue 2.0 | The Eden Power Tray Page 20

Setting up the controller

The Eden Power Tray

3. Setting up the controller

The Eden Compact can be set up via a variety of different methods:

 Through the front panel display and function keys  Through the RCS system manager  Directly via the controllers communication port using a PC  Across an IP network

Subsequent pages will identify and explain each menu group and individual parameter in detail when utilising the function keys on the front of the Eden controller for set up purposes. Information has been presented in exactly the same format as it will appear to the user on the display, and descriptions of each function are given along with the maximum, minimum and default values for HT and LT variants.

If the user wishes to confirm / modify parameters using the RCS system manager then the Eden controllers will need to be logged onto the system to achieve this, please complete the Setup and Address sections as identified on pages 8-11 before proceeding to use the system manager.

Controllers can be pre-commissioned with identical non default parameter sets via the use of a PC connected directly into the Eden controller’s communication port. To achieve this a simple software application is available from RCS upon request.

3.1 Front Panel Display Keys & Icons:-

The Eden Compact consists of a very attractive front panel display and a keypad. The display has 4 digits, decimal point and icons. It shows temperatures, all parameter values, and the main unit status.

The silicon keypad ensures ease of use and reliability.

The front panel incorporates a blue LED 4 character display for indicating temperatures and status / alarm messages. The four function keys are identified below:-

Installation Guide | Issue 2.0 | The Eden Power Tray Page 21

Setting up the controller

The Eden Power Tray

Alarm

Critical alarm present, see Alarms Menu – Page 10

Service

See Parameter Ti9 – Page 18

HACCP

See Parameter Su9 – Page 9

Valve

Illuminated when Relay 1 is on – Pages 28-29

Fans

Illuminated when Relay 2 is on - Pages 28-29

Lights

Illuminated when Relay 3 is on - Pages 28 - 29

Defrost

Illuminated when Relay 5 is on – Pages 28-29

Network

Off = No Network attached / network failure On = Network Established

Installation Guide | Issue 2.0 | The Eden Power Tray Page 22

Setting up the controller

The Eden Power Tray

3.2 Using the front panel display and function keys

Display Text

Menu Group

Information

Set

Initial controller setup

Setup

Addr

485 / IP comms configuration

Address

rEF

Refrigeration Mode Parameters

Refrigeration

dEF

Defrost Mode Parameters

Defrost

FAnS

Fans parameters

Fans

ti

Time related Parameters

Times

StA

Unit Status Information

Status

ALAr

Unit Alarm Information

Alarms

LtS

Lights related Parameters

Lights

SLP

Sleep Mode

Sleep

SELF

Self Test Mode

Self

To enter setup press the FUNCTION and UP buttons simultaneously for greater than 3 seconds until the message SEt appears. Pressing the ENTER key again at this point will allow access to the first item in the setup menu (Su1). Pressing the FUNCTION button at any point will return the user to the previous menu. The UP / DOWN buttons can be used to scroll through the available menu groups, as listed below. Once the required menu group is displayed pressing the enter key again will allow access to that group as described above.

The following pages provide details of each menu group in order. It is recommended that the user follows this sequence to ensure correct setup is achieved.

If no buttons are pressed for a period greater than 3 minutes the display will revert to indicating the actual cabinet temperature. This applies to all menus.

Installation Guide | Issue 2.0 | The Eden Power Tray Page 23

Setting up the controller

The Eden Power Tray

3.2.1 Set Up Menu

I/D

Parameter

Range

Units

Deflt LSV

Deflt EEV

Information

Su1

Unit Type

0 = HT Integral 1 = LT Integral 2 = HT Remote Case 3 = LT Remote Case 4 = HT Coldstore 5 = LT Coldstore

4 4

Options 1 and 2 not valid if EEV variant.

Su2

Control Probe Type

0 =Use Air On Probe 1 = Use Log Probe

Air On

Selects between using the air on, or the log probe as the control temperature. If Su3 is set to 0 (off) N/A will appear

Su3

Log Probe Type

0 = Off 1 = Logging 2 = Logging with Alarm

0 - Off

0- Off

Selects the function of the log probe. (if fitted)

Su4

Trim In Defrost

No Yes

No

Selects the state (on or off) of the trim heater output during defrost.

Su5

Trim Output %

0 – 100

%

100

Selects the percentage output level of the trim heater output on a 100 second time base. Example – if Su5 = 10% then trim on for 10 seconds and off for 90 seconds.

Su6

Relay 4 Function

0 = Suction 1 = Trim 2 = Compressor 2

Suction

If unit type 1 or 2 is selected this parameter will default to 2 – compressor 2

Accessed by pressing and holding the FUNCTION and UP keys simultaneously for greater than 3 seconds. The display will indicate SEt, at this point press the ENTER button again and the display will indicate Su1. This is the first item in the set up menu. The UP and DOWN keys can be used to scroll through the entire list of set up items – from Su1 through to Su12. See table below:- Pressing ENTER whilst displaying any Su number will allow the user to view and modify that particular value by using the UP / DOWN keys to either increment or decrement the default value. Once the desired value is displayed press ENTER again to save, or use the FUNCTION key to return to previous menu without saving.

Installation Guide | Issue 2.0 | The Eden Power Tray Page 24

Setting up the controller

The Eden Power Tray

I/D

Parameter

Range

Units

Deflt LSV

Deflt EEV

Information

Su7

Digital Input 1 Function

0 = Case Clean 1 = Door Open 2 = C1 Fault 3 = Man Trapped

Case Clean

Case -

- Clean

Default for cabinet type 3 and 4 is case clean. If unit type 1 or 2 selected (su1) then default value becomes 2 – C1 Fault. If unit type 5 or 6 selected (su1) then default becomes 1 – Door alarm. All digital inputs are contact sense N/O. N/C for alarm.

Su8

Digital Input 2 Function

0 = Case Clean 1 = Door Open 2 = C2 Fault 3 = Man Trapped

Case -

- Clean

Case -

- Clean

Default for cabinet type 3 and 4 is case clean. If unit type 1 or 2 selected (su1) then default value becomes 2 – C2 Fault. If unit type 5 or 6 selected (su1) then default becomes 1 – Man Trapped alarm. All digital inputs are contact sense N/O. - N/C for alarm.

Su9

HACCP Function

0 = Off 1 = On 2 = Flashing

0 - Off

0- Off

Selects the state of the front panel HACCP icon.

Su10

Sensor Type

0 = PT1000 1 = 5K NTC 2 = 10K NTC 3 = 2K2 NTC

PT1000

Selects the temperature sensor type being used. Note – sensor types cannot be mixed on a single controller

Su11

Evaporator Probes Fitted

0 = Not Fitted 1 = Fitted

1 - Fitted

Allows the user to select if Evaporator In and Out sensors are fitted.

Su12

Number of Compressors

1 2 2 2

Selects the number of compressors in use when unit type 1 or 2 (integral) is configured

Installation Guide | Issue 2.0 | The Eden Power Tray Page 25

Setting up the controller

The Eden Power Tray

3.2.2 Controller address and communications menu.

I/D

Parameter

Range

Units

Deflt LSV

Deflt EEV

Information

485A

Controller RS485 communication address (unit number)

0.0 – 499.9

0.0

Allows the user to set the controllers network address for RS485 legacy systems

485C

Controller RS485 communication baud rate

0 = 9600 1 = 600

9600

Allows the user to set the controllers network baud rate for RS485 legacy systems

IP-1

IP Address Byte 1

0 – 255

0 0

Allows the user to set the first byte of the controllers IP address. Note- If DHCP is set to yes this value is not editable.

IP-2

IP Address Byte 2

0 – 255

0 0

Allows the user to set the second byte of the controllers IP address. Note- If DHCP is set to yes this value is not editable.

IP-3

IP Address Byte 3

0 – 255

0 0

Allows the user to set the third byte of the controllers IP address. Note- If DHCP is set to yes this value is not editable.

IP-4

IP Address Byte 4

0 – 255

0 0

Allows the user to set the fourth byte of the controllers IP address. Note- If DHCP is set to yes this value is not editable.

Sn -1

Sub-Net Address Byte 1

0 – 255

0 0

Allows the user to set the First byte of the controllers sub net mask. Note- If DHCP is set to yes this value is not editable.

Accessed by pressing and holding the FUNCTION and UP keys simultaneously for greater than 3 seconds. The display will indicate SEt, Press the DOWN key once - the display will indicate Addr at this point press the ENTER button and the display will indicate 485A. This is the first item in the address menu. The UP and DOWN keys can be used to scroll through the entire list of set up items – from 485A through to DGT. See table below:Pressing ENTER whilst displaying any item will allow the user to view and modify that particular value by using the UP / DOWN keys to either increment or decrement the default value. Once the desired value is displayed press ENTER again to save, or use the FUNCTION key to return to previous menu without saving.

Installation Guide | Issue 2.0 | The Eden Power Tray Page 26

Setting up the controller

The Eden Power Tray

I/D

Parameter

Range

Units

Deflt LSV

Deflt EEV

Information

Sn -2

Sub-Net Address Byte 2

0 – 255

0 0

Allows the user to set the second byte of the controllers sub net mask. Note- If DHCP is set to yes this value is not editable.

Sn -3

Sub-Net Address Byte 3

0 – 255

0 0

Allows the user to set the third byte of the controllers sub net mask. Note- If DHCP is set to yes this value is not editable.

Sn -4

Sub-Net Address Byte 4

0 – 255

0 0

Allows the user to set the fourth byte of the controllers sub net mask. Note- If DHCP is set to yes this value is not editable.

Gt1

Network Gateway Address Byte 1

0 – 255

0 0

Allows the user to set the first byte of the network gateway address.

Gt2

Network Gateway Address Byte 2

0 – 255

0 0

Allows the user to set the second byte of the network gateway address.

Gt3

Network Gateway Address Byte 2

0 – 255

0 0

Allows the user to set the third byte of the network gateway address.

Gt4

Network Gateway Address Byte 2

0 – 255

0 0

Allows the user to set the fourth byte of the network gateway address.

NtP1

NTP server Address Byte 1

0 – 255

0 0

Allows the user to set the first byte of the NTP server address

NtP2

NTP server Address Byte 2

0 – 255

0 0

Allows the user to set the second byte of the NTP server address

NtP3

NTP server Address Byte 3

0 – 255

0 0

Allows the user to set the third byte of the NTP server address

NtP4

NTP server Address Byte 4

0 – 255

0 0

Allows the user to set the fourth byte of the NTP server address

dHCP

DHCP Enabled

Yes No

Yes

Configures if DHCP is being used

dntP

NTP server address obtained via DHCP

Yes No

Yes

Configures if the NTP server address is automatically obtained via DHCP

dGt

Network gateway address obtained via DHCP

Yes No

Yes

Configures if the gateway address is automatically obtained via DHCP

If the user is unsure of any network related parameter please consult your network administrator

Installation Guide | Issue 2.0 | The Eden Power Tray Page 27

Setting up the controller

The Eden Power Tray

3.2.3 Controllers Refrigeration related parameter menu.

I/D

Parameter

Range

Units

Deflt LSV

Deflt EEV

Information

rF1 Force Refrigeration

No Yes

No

Allows the user to force the controller into a forced refrigeration state. During the force refrigeration state any scheduled defrosts will be ignored. The controller will remain in this state until either NO is selected or a period of 60 minutes has elapsed.

rF2

Temperature Setpoint

-40.0°C - +35.0°C

°C

1.0°C HT

-20°C LT

-1.0°C HT C/S

-20°C - LT C/S

1.0°C HT

-20°C LT

-1.0°C HT C/S

-20°C LT C/S

Temperature at which inlet valve or compressor/s will switch on rF3

Temperature Diff.

0.2 – 5.0°C

°C

1.0°C HT

2.0°C LT

1.0°C HT

2.0°C LT

Differential temperature below the temperature setpoint at which the inlet valve or compressor will switch off

rF4 Control Ratio

0 – 100%

%

66% Cabinet 100% Coldstore

Ratio of Air On temperature that is used to calculate the estimated cabinet temperature for control. The remaining percentage used is Air off temperature.

rF5 Display Ratio

0 – 100%

%

66

As above only applied to the front panel display temperature.

Accessed by pressing and holding the FUNCTION and UP keys simultaneously for greater than 3 seconds. The display will indicate SEt, Press the DOWN key 2 times - the display will indicate rEF, at this point press the ENTER button and the display will indicate rF1. This is the first item in the REFRIGERATION menu. The UP and DOWN keys can be used to scroll through the entire list of the rEF menu – from rF1 through to Rf16. See table below:Pressing ENTER whilst displaying any item will allow the user to view and modify that particular value by using the UP / DOWN keys to either increment or decrement the default value. Once the desired value is displayed press ENTER again to save, or use the FUNTION key to return to the previous menu without saving.

Installation Guide | Issue 2.0 | The Eden Power Tray Page 28

Setting up the controller

The Eden Power Tray

I/D

Parameter

Range

Units

Deflt LSV

Deflt EEV

Information

rF6 Superheat Setpoint

0.0 - 9.0

°C

6.0°C

The controller will attempt to maintain this superheat setpoint N/A will be displayed if LSV version.

rF7 EEV Injection percentage

0 – 100%

%

45%

Sets the value of the EEV when in a recovery state. N/A will be displayed if LSV version.

rF8 Air On Alarm Setpoint

-40.0°C - +35.0°C

°C

8.0 HT

-10.0 LT

8.0 HT

-10.0 LT

Sets the Air On alarm setpoint

rF9 Air Off Alarm Setpoint

-40.0°C - +35.0°C

°C

4.0 HT

-20.0 LT

3.0 HT C/S

-18.0 LT C/S

4.0 HT

-20.0 LT

3.0 HT C/S

-18.0 LT C/S

Sets the Air Off alarm setpoint

rF10

Logging Probe OT Alarm Setpoint

-40.0°C - +35.0°C

°C

10.0 HT

-12.0 LT

10.0 HT

-12.0 LT

Sets the log probe over temperature alarm setpoint. NOTE – N/A will be displayed if Su3 is not set to 2

rF11

Logging Probe UT Alarm Setpoint

-40.0°C - +35.0°C

°C

-5.0 HT

-35.0 LT

-5.0 HT

-35.0 LT

Sets the log probe under temperature alarm setpoint NOTE – N/A will be displayed if Su3 is not set to 2

rF12

EEV Minimum Opening

0 – 100%

%

15%

Sets the minimum valve opening during normal operation. The controller will prevent the valve from closing below this value. N/A will be displayed if LSV version.

rF13

Manual EEV Control

0 = No 1 = Yes

0 - No

0 – No

Allows the user to manually control the EEV valve opening % if set to Yes. Used in conjunction with rF14 N/A will be displayed if LSV version.

rF14

Manual EEV Opening

0 – 100 %

% 0 0

If rF13 is set to yes, the manual % opening value. The EEV will remain at this percentage until manual control is exited N/A will be displayed if LSV version.

rF15

Air On setpoint

-40.0°C - +20.0°C

°C

-3.0 HT

-20.0 LT

-3.0 HT

-20.0 LT

Temperature at which inlet valve or compressor/s will switch on. Note N/A will be displayed if not type 4 or 5 (coldstore)

rF16

Evaporator Offset to allow injection state

-10.0°C - +10.0°C

°C

0.0 HT

2.0 LT

0.0 HT

2.0 LT

Temperature offset from the ECT setpoint at which the injection (recovery) state can be entered Note N/A will be displayed if not type 4 or 5 (coldstore)

Installation Guide | Issue 2.0 | The Eden Power Tray Page 29

Setting up the controller

The Eden Power Tray

3.2.4 Controllers DEFROST menu.

I/D

Parameter

Range

Units

Deflt LSV

Deflt EEV

Information

dF1

First Defrost Time

00:01 – 23:59

hh:mm

01:00

Sets the first scheduled defrost time

dF2

Number of Defrosts per Day

0 – 8 6 6 Sets the number of defrost cycles per day. Automatically spaced equally from the first defrost time (dF1)

dF3

Maximum Defrost Duration

00:00 – 01:59

hh:mm

00:30

Maximum time that a scheduled defrost cycle can run. Note Timed from the end of defrost Minimum (dF4)

dF4

Minimum Defrost Duration

00:00 – 01:59

hh:mm

00:05

Minimum time that a scheduled defrost cycle must run before terminating. If termination temperature is achieved during this period the controller will turn off the defrost output but not return to refrigeration mode until period has elapsed.

dF5

Pump Down Duration

0 – 60

mm 0 0

Pump down time prior to minimum defrost duration (dF4) commencing

dF6

Drain Down Duration

0 – 60

mm

02

Drain down time after defrost has terminated to allow water to be cleared.

Accessed by pressing and holding the FUNCTION and UP keys simultaneously for greater than 3 seconds. The display will indicate SEt, Press the DOWN key 3 times - the display will indicate dEF, at this point press the ENTER button and the display will indicate dF1. This is the first item in the DEFROST menu. The UP and DOWN keys can be used to scroll through the entire list of the DEFROST menu – from dF1 through to dF13. See table below:Pressing ENTER whilst displaying any item will allow the user to view and modify that particular value by using the UP / DOWN keys to either increment or decrement the default value. Once the desired value is displayed press ENTER again to save, or use the FUNCTION key to return to the previous menu without saving.

Installation Guide | Issue 2.0 | The Eden Power Tray Page 30

Setting up the controller

The Eden Power Tray

I/D

Parameter

Range

Units

Deflt LSV

Deflt EEV

Information

dF7

Defrost termination Temperature

-40.0°C - +35.0°C

°C

8.0°C

Scheduled defrost will terminate when the defrost termination sensor reaches this temperature. Note – If the defrost termination sensor is not fitted (or faulty) then defrost termination will occur when the Evap. In sensor reaches this temperature if fans off, or the Air Off sensor reaches this temperature if fans on.

dF8

Defrost termination sensor in Use

0 = Defrost 1 = Air Off 2 Evap. In

0 = Defrost

Allows the user to select the sensor used for defrost termination.

dF9

Defrost Type

0 = Electric 1 = Hot Gas

0 Electric

0 – Electric

Allows the user to select if electric or hot gas defrost in being used.

dF10

Suction Valve after Hot Gas defrost

Open Closed

Closed

Allows the user to select if the suction valve is open or closed during the drain down period. Only applicable if Hot Gas defrost is selected at dF9

dF11

Force Defrost

Yes No

No

Sets the controller into defrost. The controller will remain in this mode until either No is selected or max defrost duration (Df3) time is exceeded.

dF12

Trigger Defrost

Yes No

No

Allows the user to trigger a defrost cycle additional to those scheduled. All normal termination criteria apply.

dF13

LSV during Hot Gas Defrost

0 = Closed 1 = Open

0 Closed

0 – Closed

Allows the user to select if the evaporator inlet valve is open or closed during a hot gas defrost. Only applicable if Hot Gas defrost is selected at dF9

dF14

Suppress Full Length Defrost

Yes No

No

Allows the user to prevent the controller from entering a full length defrost at the scheduled time/s when the defrost termination temperature is above the termination setpoint (df7) at the start of defrost.

Installation Guide | Issue 2.0 | The Eden Power Tray Page 31

Setting up the controller

The Eden Power Tray

3.2.5 Controllers Fan related parameter menu.

I/D

Parameter

Range

Units

Deflt LSV

Deflt EEV

Information

Fn1 Fans Only Mode

0 = No 1 = Yes 2 = Lights and Fans Only

0 – No

Allows the user to set the controller into Fans Only Mode. The controller will remain in this mode until No is selected.

Fn2

Maximum Fans off Time

0 – 60

mm 0 0

Maximum time for which the fans are switched off following draindown.

Fn3

Fans Off Temperature During Defrost

-40.0°C - +35.0°C

°C 8.0°C (HT)

-10.0°C (LT)

8.0°C (HT)

-10.0°C (LT)

Allows the user to determine the temperature at which fans will turn off during defrost. Once turned off by this setting fans will remain off for the remaining defrost duration. NOTE If -40.0°C is selected fans will be always off during defrost

Fn4 Fans Off Delay Time

0 – 60

ss 0 0

The delay time before fans are switched off when a door open state is entered. Note N/A will be displayed if not type 4 or 5 (coldstore)

Fn5

Fans Holdoff End setpoint

-40.0°C - +35.0°C

°C 0.0°C (HT)

-10.0°C (LT)

0.0°C (HT)

-10.0°C (LT)

Defrost termination sensor temperature which when achieved will allow fans to be switched on.

Fn6

Fans Pulse In defrost

No Yes

0 = No

Allows the user to select if evaporator fans pulse during defrost

Accessed by pressing and holding the FUNCTION and UP keys simultaneously for greater than 3 seconds. The display will indicate SEt, Press the DOWN key 4 times - the display will indicate FAns, at this point press the ENTER button and the display will indicate Fn1. This is the first item in the FANS menu. The UP and DOWN keys can be used to scroll through the entire list of the FANS menu – from Fn1 through to Fn9. See table below:Pressing ENTER whilst displaying any item will allow the user to view and modify that particular value by using the UP / DOWN keys to either increment or decrement the default value. Once the desired value is displayed press ENTER again to save, or use the FUNCTION key to return to the previous menu without saving.

Installation Guide | Issue 2.0 | The Eden Power Tray Page 32

Setting up the controller

The Eden Power Tray

I/D

Parameter

Range

Units

Deflt LSV

Deflt EEV

Information

Fn7

Fans On setpoint

-10.0°C - +30.0°C

°C 50.0°C (HT)

-1.0°C (LT)

5.0°C (HT)

-1.0°C (LT)

Cold store Only. Defrost termination sensor temperature or Air On temperature which when achieved will allow fans to be switched on. Note N/A will be displayed if not type 4 or 5 (coldstore)

Fn8

Fans Pulse Time

5 – 600

ss

60

Time in seconds for which the fans will alternate between on and off if Fn6 is set to yes

Fn9

Door Open State Closes Valve

0 = No 1 = Yes

0 – No

Allows the user to select if a door open state closes the evaporator inlet valve. Note N/A will be displayed if not type 4 or 5 (coldstore)

Installation Guide | Issue 2.0 | The Eden Power Tray Page 33

Setting up the controller

The Eden Power Tray

3.2.6 Controllers time related parameter menu.

I/D

Parameter

Range

Units

Deflt LSV

Deflt EEV

Information

ti1

Time of Day

00:00 – 23:59

hh:mm

00:00

Allows the user to set the correct time of day into the controller. Note on networked systems the time of day will automatically be down loaded from the host system

ti2

Current Date

01:01 – 31:12

dd:mm

00:00

Sets the controllers current date ti3

Current Year

2012 -2100

0000

Sets the controllers current year

ti4

Time of Next Defrost

hh:mm

Allows the user to view the time of the next scheduled defrost cycle.

ti5

Time Since last defrost

hh:mm

Allows the user to view the time since the last scheduled defrost cycle occurred.

ti6

Duration of last defrost

hh:mm

Allows the user to view the duration time of the last scheduled defrost cycle.

ti7

Duration of current defrost

hh:mm

Allows the user to view the elapsed time of a current defrost cycle.

ti8

Door Alarm Delay

0 – 120

mm

Delay after the door open input is asserted before the alarm occurs. Note N/A will be displayed if not type 4 or 5 (coldstore)

ti9

Service Interval Time

0 – 130

khrs

60

Running time in KHrs (1000x) before the front panel service (spanner) icon is illuminated. Reset can be achieved by changing the value to 0 then back to the desired interval.

ti10

Air On Alarm Delay

0 – 120

mm

20

Delay for the Air On OT alarm

Accessed by pressing and holding the FUNCTION and UP keys simultaneously for greater than 3 seconds. The display will indicate SEt, Press the DOWN key 5 times - the display will indicate Ti, at this point press the ENTER button and the display will indicate Ti1. This is the first item in the TIMES menu. The UP and DOWN keys can be used to scroll through the entire list of the TIME menu – from TI1 through to Ti19. See table below:Pressing ENTER whilst displaying any item will allow the user to view and modify that particular value by using the UP / DOWN keys to either increment or decrement the default value. Once the desired value is displayed press ENTER again to save, or use the FUNCTION key to return to previous menu without saving.

Installation Guide | Issue 2.0 | The Eden Power Tray Page 34

Setting up the controller

The Eden Power Tray

I/D

Parameter

Range

Units

Deflt LSV

Deflt EEV

Information

ti11

Air Off Alarm Delay

0 – 120

mm

20

Delay for the Air Off OT alarm

ti12

Log Probe Alarm Delay

00:00 – 02:00

hh:mm

00:20

Delay for the log probe alarm NOTE – N/A will be displayed if Su3 is not set to 2

ti13

Cycle Time

0 – 120

mm

60

Energy saving feature (LSV use) see appendix 1.

ti14

EEV Injection Time

0 – 30

mm 4 4

Maximum period the controller can be in an injection (stall prevention) state. N/A will be displayed if LSV version.

ti15

Pull Down Time

0 – 30

ss 8 8

Time after draindown, before an injection state (recovery) state can be entered

ti16

Door Open Time

0 – 60

mm

Displays the time a cold store door has been continuously open for. Note N/A will be displayed if not type 4 or 5 (coldstore)

ti17

Door Interlock Time

0 – 60

mm

0 (HT)

5 (LT)

0 (HT)

5 (LT)

Maximum time for which fans and /or inlet valve are off / closed when a cold store door is open. Note N/A will be displayed if not type 4 or 5 (coldstore)

ti18

Compressor/s start holdoff Time

0 – 15

mm 4 4

Time period following initial power up of the controller before compressors can be started – Integral use only

ti19

Compressor/s Restart Time

0 – 15

mm 4 4

Anti – short cycle time for compressor 1 and 2 – Integral use only

Ti20

Compressor/s stage Time

0 – 15

mm 4 4

Period which must elapse between compressor A changing state and subsequent change of state of compressor B – Integral use only

Ti21

Compressor/s Minimum On Time

0 – 15

mm 4 4

Minimum time compressor/s must run once started – Integral use only

Ti22

Compressor/s Minimum Off Time

0 – 15

mm 4 4

Minimum time compressor/s must be stopped once switched off – Integral use only

Installation Guide | Issue 2.0 | The Eden Power Tray Page 35

Setting up the controller

The Eden Power Tray

3.2.7 Controllers current status menu.

I/D

Parameter

Range

Units

Deflt LSV

Deflt EEV

Information

St1

Air On Temperature

°C Displays the current Air On sensor Temperature.

St2

Air Off Temperature

°C

Displays the current Air Off sensor Temperature

St3

Evaporator In Temperature

°C

Displays the current Evap. In sensor Temperature

St4

Evaporator Out Temperature

°C

Displays the current Evap. Out sensor Temperature

St5

Superheat

°C

Displays the current superheat Temperature

St6

Defrost sensor Temperature

°C

Displays the current Defrost termination sensor Temperature

St7

Estimated cabinet Temperature

°C

Displays the current estimated cabinet temperature. This is defined by the ratio of air on temperature set within the rEF menu at rF5 (Display Ratio)

St8

Log Probe Temperature

°C

Displays the current log sensor Temperature.

St9

Analogue channel 7

Displays the current value of analogue input channel 7. (Hardware configurable).

St10

Trim Output percentage

% Displays the current percentage of the controllers trim output.

St11

Digital Input 1

Open Closed

Displays the current state of controllers digital input 1. Function dependant upon selection made in SETUP menu – Su7

Accessed by pressing and holding the FUNCTION and UP keys simultaneously for greater than 3 seconds. The display will indicate SEt, Press the UP key 6 times - the display will indicate StA, at this point press the ENTER button and the display will indicate St1. This is the first item in the STATUS menu. The UP and DOWN keys can be used to scroll through the entire list of the STATUS menu – from St1 through to St20. See table below: Pressing ENTER whilst displaying any item will allow the user to view that particular value. None of the items within this menu are user editable. Use the FUNCTION key to return to previous menu.

Installation Guide | Issue 2.0 | The Eden Power Tray Page 36

Setting up the controller

The Eden Power Tray

I/D

Parameter

Range

Units

Deflt LSV

Deflt EEV

Information

St12

Digital Input 2

Open Closed

Displays the current state of controllers digital input 2. Function dependant upon selection made in SETUP menu – Su8

St13

Case Clean

On Off

Displays if the controller is currently in case clean mode. (all outputs off)

St14

EEV percentage open

% Displays the current percentage opening of the EEV. .N/A will be displayed if LSV version.

St15

Compressor 1 Fault

Yes No

Displays the current fault status of C1 (Integral only)

St16

Compressor 2 Fault

Yes No

Displays the current fault status of C2 (Integral only)

St17

Compressor 1 Running

Yes No

Displays the current status of controllers C1 output. (Integral only)

St18

Compressor 2 Running

Yes No

Displays the current status of controllers C2 output. (Integral only)

St19

Software Version

Displays controllers software version

St20

Display software version

Displays controllers display version

Installation Guide | Issue 2.0 | The Eden Power Tray Page 37

Setting up the controller

The Eden Power Tray

3.2.8 Controllers current alarms menu.

I/D

Parameter

Range

Units

Deflt LSV

Deflt EEV

Information

AL1

Any Alarms

Yes No

Allows the user to quickly establish if any alarm conditions are currently Active.

AL2

Air On OT

Yes No

Indicates if the controller currently has an Air On over temperature alarm.

AL3

Air Off OT

Yes No

Indicates if the controller currently has an Air Off over temperature alarm.

AL4

Air On Sensor Failure

Yes No

Indicates if the controller currently has a faulty Air On temperature sensor.

AL5

Air On Sensor Failure

Yes No

Indicates if the controller currently has a faulty Air Off temperature sensor.

AL6

Evaporator In Sensor Failure

Yes No

Indicates if the controller currently has a faulty Evap. In temperature sensor.

AL7

Evaporator Out Sensor Failure

Yes No

Indicates if the controller currently has a faulty Evap. Out temperature sensor.

AL8

Defrost Termination Sensor Failure

Yes No

Indicates if the controller currently has a faulty Defrost Termination temperature sensor.

Accessed by pressing and holding the FUNCTION and UP keys simultaneously for greater than 3 seconds. The display will indicate SEt, Press the UP key 4 times - the display will indicate ALAr, at this point press the ENTER button and the display will indicate AL1. This is the first item in the ALARMS menu. The UP and DOWN keys can be used to scroll through the entire list of the ALARMS menu – from AL1 through to AL14. See table below:Pressing ENTER whilst displaying any item will allow the user to view that particular value. None of the items within this menu are user editable. Use the FUNCTION key to return to previous menu.

Installation Guide | Issue 2.0 | The Eden Power Tray Page 38

Setting up the controller

The Eden Power Tray

I/D

Parameter

Range

Units

Deflt LSV

Deflt EEV

Information

AL9

Logging Sensor Failure

Yes No

Indicates if the controller currently has a faulty Log temperature sensor.

AL10

Door Open (Cold store Only)

Yes No

Indicates if the controller currently has a Door Open alarm Note N/A will be

displayed if not type 4 or 5 (coldstore)

AL11

Man Trapped (Cold store Only)

Yes No

Indicates if the controller currently has a Man Trapped alarm Note N/A will be displayed

if not type 4 or 5 (coldstore)

AL12

Insufficient Data

Yes No

Indicates if the controller currently has an Insufficient Data alarm. Note – Usually occurs when defrost time 1 has not been set.

AL13

Compressor 1 Alarm (Integral Only)

Yes No

Indicates if the controller currently has a Compressor 1 Fault.

AL14

Compressor 2 Alarm (Integral Only)

Yes No

Indicates if the controller currently has a Compressor 2 Fault.

AL15

Critical Probe Fault

Yes No

Set if the controller currently has more than one temperature sensor in a fault condition.

Note – All of the above alarms if present will cause the front panel Bell Icon to be illuminated.

Installation Guide | Issue 2.0 | The Eden Power Tray Page 39

Setting up the controller

The Eden Power Tray

3.2.9 Controllers lights related parameter menu.

I/D

Parameter

Range

Units

Deflt LSV

Deflt EEV

Information

Li1

Lights control Mode

0 – Remote 1 – Local 2 – Off 3 – On

2 2

Allows the user to set the control of case lights:0 = Case lights controlled via host System manager. 1 = Case lights controlled via controller schedule (see Li2 – Li15) 2 = Always Off 3 = Always On

Li2

Sunday Lights On Time

00:00 – 23:59

hh:mm