2.4 GHz Cordless Telephone
and Wireless Headset
with Call-Waiting/Caller ID
User’s Guide
Please read this manual before
operating this product for the first time.
Model 25110
TM
2
Important Information
NOTICE: This product meets the applicable Industry Canada technical specifications.
Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) This device must accept any
interference, including interference that may cause undesired operation of the device.
The equipment must be installed using an acceptable method of connection. The customer should be aware that compliance with the above
conditions may not prevent degradation of service in some situations.
Repairs to certified equipment should be made by an authorized Canadian maintenance facility designated by the supplier. Any repairs or
alterations made by the user to this equipment, or equipment malfunctions, may give the telecommunications company cause to request the
user to disconnect the equipment.
Users should ensure for their own protection that the electrical ground connections of the power utility, telephone lines and internal metallic
water pipe systems, if present, are connected together. This precaution may be particularly important in rural areas.
CAUTION: Users should not attempt to make such connections themselves, but should contact the appropriate electric inspection authority, or
electrician, as appropriate.
NOTES: This equipment may not be used on coin service provided by the telephone company.
REN NUMBER IS LOCATED ON THE CABINET BOTTOM
Important Information
3
Interference Information
This equipment generates and uses radio frequency energy which may interfere with residential radio and television reception if not
properly installed and used in accordance with instructions contained in this manual. Reasonable protection against such interference is
ensured, although there is no guarantee this will not occur in a given installation. If interference is suspected and verified by switching
this equipment on and off, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient
the radio/television receiver’s antenna, relocate the equipment with respect to the receiver, plug the equipment and receiver into separate
circuit outlets. The user may also wish to consult a qualified radio/television technician for additional suggestions. This equipment has been
fully tested and complies with all limits for Class B computing devices pursuant to part 15 FCC Rules and Regulations.
Hearing Aid Compatibility
This telephone system meets FCC standards for Hearing Aid Compatibility.
Licensing
Licensed under US Patent 6,427,009.
Important Information
4
Table of Contents
Important InformatIon ................................................................. 2
Interference InformatIon .............................................................. 3
HearIng aId compatIbIlIty ............................................................ 3
lIcensIng ..................................................................................... 3
IntroductIon ................................................................................ 6
parts cHecklIst ............................................................................ 7
Important InstallatIon InformatIon...............................................8
Safety PrecautionS ..................................................................................8
inStallation GuidelineS ...........................................................................8
telepHone Jack requIrements ........................................................ 9
pHone InstallatIon ..................................................................... 10
connectinG the ac (electrical) Power .............................................. 10
Charger unit ............................................................................................. 10
Wall base unit ......................................................................................... 10
connectinG the telePhone line ............................................................ 10
inStallinG the BatterieS ........................................................................11
Installing the Handset Battery ............................................................11
Installing the Headset Battery ...........................................................12
Headset set up.......................................................................... 13
headBand attachment ......................................................................... 13
To switch from ear to ear .................................................................... 14
ear cliP attachment ............................................................................15
To switch from ear to ear .................................................................... 15
Handset layout ......................................................................... 16
Headset layout ..........................................................................17
Handset set up ......................................................................... 18
diSPlay lanGuaGe ................................................................................. 18
tone/PulSe dialinG .............................................................................. 18
area code.............................................................................................18
rinGer tone .......................................................................................... 19
rinGer Volume ..................................................................................... 19
default SettinG Selection .................................................................... 19
telepHone operatIon ..................................................................20
makinG a call ...................................................................................... 20
On the Handset .......................................................................................20
On the Headset .......................................................................................20
anSwerinG a call ................................................................................ 20
On the Handset ...........................................................................20
On the Headset ...........................................................................20
call tranSfer ....................................................................................... 21
mute ..................................................................................................... 21
redial .................................................................................................... 21
flaSh ..................................................................................................... 22
exit ........................................................................................................22
handSet Volume ...................................................................................22
headSet Volume ................................................................................... 22
To Adjust Volume from Headset: .......................................................22
To Adjust Volume from Handset: ...................................................... 22
5
Table of Contents
PaGinG the handSet and headSet ........................................................23
in uSe indicator liGht ......................................................................... 23
On the Handset .......................................................................................23
On the Headset .......................................................................................23
charGer indicator liGht ...................................................................... 23
call timer ............................................................................................ 24
temPorary tone dialinG ...................................................................... 24
caller Id .................................................................................. 25
caller id with call waitinG .............................................................. 25
receiVinG and StorinG callS ............................................................... 25
reViewinG recordS ............................................................................... 25
tranSferrinG cid recordS to memory .............................................. 26
deletinG recordS ................................................................................. 26
deletinG the current record .............................................................. 26
deletinG all recordS ........................................................................... 27
dialinG a caller id numBer ............................................................... 27
chanGinG the cid numBer format ....................................................27
memory .................................................................................... 28
StorinG a name and numBer in memory ........................................... 28
ViewinG a Stored numBer ................................................................... 29
chanGinG a Stored numBer ................................................................ 29
StorinG a redial numBer .................................................................... 29
dialinG a Stored numBer .................................................................... 30
inSertinG a PauSe in the dialinG Sequence of a Stored numBer ......30
reViewinG and deletinG Stored numBerS ........................................... 30
Headset and belt clIp operatIon ................................................ 31
connectinG an oPtional headSet to the handSet .............................. 31
attachinG the Belt cliP ....................................................................... 31
replacIng tHe batterIes .............................................................. 32
handSet Battery ................................................................................... 32
handSet memory retention ............................................................... 32
headSet Battery ................................................................................... 33
battery safety precautIons ........................................................ 33
dIsplay messages ...................................................................... 34
Handset sound sIgnals .............................................................. 35
caller id .............................................................................................. 36
No display ................................................................................................. 36
Caller ID error message ........................................................................36
telePhone .............................................................................................. 36
No dial tone .................................................................................36
troublesHootIng tIps ..................................................................37
general product care ............................................................... 38
causes of poor receptIon .......................................................... 38
telepHone network InformatIon ................................................. 39
ren number .............................................................................40
servIce ...................................................................................... 41
accessory InformatIon ............................................................... 43
6
SE E M ARK ING ON BO TTO M / BA CK OF P ROD UCT
RISK OF ELECTRIC SHOCK
DO NOT OPEN
WARNING: TO
PREVENT FIRE OR
ELECTRICAL SHOCK
HAZARD, DO NOT
EXPOSE THIS
PRODUCT TO RAIN
OR MOISTURE.
THE LIGHTNING
FLASH AND ARROW
HEAD WITHIN THE
TRIANGLE IS A
WARNING SIGN
ALERTING YOU OF
“DANGEROUS
VOLTAGE” INSIDE
THE PRODUCT.
CAUTION: TO REDUCE THE
RISK OF ELECTRIC SHOCK, DO
NOT REMOVE COVER (OR
BACK). NO USER
SERVICEABLE PARTS INSIDE.
REFER SERVICING TO
QUALIFIED SERVICE
PERSONNEL.
THE EXC LAMAT ION
POINT WITHIN THE
TRIANGLE IS A
WARNING SIGN
ALERTING YOU OF
IMPORTANT
INSTRUCTIONS
ACCOMPANY ING
THE PRODUCT.
CAUTION:
Important Information
Introduction
CAUTION: When using telephone equipment, there are basic safety instructions that
should always be followed. Refer to the IMPORTANT SAFETY INSTRUCTIONS provided
with this product and save them for future reference.
Your Caller ID phone stores and displays information provided by your local
telephone company, to subscribers of Caller ID or similar caller identification
services.
Your Caller ID phone enables you to:
• Identify callers before you answer the phone.
• View the time and date of each incoming call.
• Record up to 99 Caller ID messages sequentially.
• Know who called while you were away.
To get the most from your new phone, we suggest that you take a few minutes
right now to read through this user’s guide.
IMPORTANT: In order to use all of the features of this unit, you must subscribe to either the
standard Name/Number Caller ID Service or Call Waiting Caller ID Service. To know who is
calling while you are on the phone, you must subscribe to Call Waiting Caller ID Service.
IMPORTANT: Because cordless phones operate on electricity, you should have at least one
phone in your home that isn’t cordless, in case the power in your home goes out.
7
Parts Checklist
Make sure your package includes the following items:
Wall base
Handset
Battery
compartment cover
Telephone
line cord
AC power
adaptor
Connections & Setup
ChargerHandset battery Belt clip
Headband Headset battery Ear clip ring
Ear clip
Headset
Headset sponge
cover
8
Important Installation Information
Safety Precautions
• Never install telephone wiring during a lightning storm.
• Never install telephone jacks in wet locations unless the jack is specifically
designed for wet locations.
• Never touch non-insulated telephone wires or terminals, unless the telephone
line is disconnected from the network.
• Use caution when installing or modifying telephone lines.
• Temporarily disconnect any equipment connected to the phone such as faxes,
other phones, or modems.
Installation Guidelines
• Install the wall base unit into an electrical outlet that is near a telephone
(modular) jack.
• Avoid sources of noise, such as a window by a busy street, and electrical noise,
such as motors, microwave ovens, and fluorescent lighting.
• Avoid heat sources, such as heating air ducts, heating appliances, radiators, and
direct sunlight.
• Avoid areas of excessive moisture or extremely low temperature.
• Avoid dusty locations.
• Avoid other cordless telephones or personal computers.
Connections & Setup
9
Modular telephone
line jack
Wall plate
Connections & Setup
CAUTION: Always disconnect all phone cords from the base unit before battery
installation or replacement.
INSTALLATION NOTE: Some cordless telephones operate at frequencies that may cause
or receive interference with TVs, microwave ovens, and VCRs. To minimize or prevent such
interference, the base of the cordless telephone should not be placed near or on top of a TV,
microwave ovens, or VCR. If such interference continues, move the cordless telephone farther
away from these appliances. Certain other communications devices may also use the 2.4GHz
frequency for communication, and, if not properly set, these devices may interfere with each
other and/or your new telephone. If you are concerned with interference, please refer to
the owner’s manual for these devices on how to properly set channels to avoid interference.
Typical devices that may use the 2.4GHz frequency for communication include wireless
audio/video senders, wireless computer networks, multi-handset cordless telephone systems,
and some long-range cordless telephone systems.
Telephone Jack Requirements
To use this phone, you will need an RJ11C type modular phone jack, which might
look like the one pictured here, installed in your home. If you don’t have a modular
jack, call your local phone company to find out how to get one installed.
10
Phone Installation
Connecting the AC (Electrical) Power
Charger unit
Plug the AC power adaptor into an electrical outlet and the DC connector into the
bottom of the charger.
CAUTION: Only use the 5-2745 power adaptor that came with this unit. Using other
power adaptors may damage the charger unit.
Wall base unit
To install your wall base unit, locate an electrical outlet with a phone jack nearby.
1. Plug the wall base unit into an electrical outlet.
2. Make sure that the pins are inserted fully and firmly into the outlet. If not,
choose another electrical outlet.
Connecting the Telephone Line
There are two jacks on the bottom of the wall base unit.
Plug one end of the telephone line cord into the LINE jack on the bottom of the
wall base unit and the other end into a modular jack.
The PHONE jack may be used to connect a parallel phone by connecting a second
telephone line cord from the PHONE jack on the bottom of the wall base unit to the
parallel phone.
Connections & Setup
11
Installing the Batteries
Installing the Handset Battery
CAUTION: To reduce the risk of fire or personal injury, only use the Thomson Inc.
approved Ni-MH battery model 5-2683.
NOTE: You must connect the handset battery before use.
1. Locate battery and battery door which are packaged together inside a plastic
bag and are separated from the handset.
2. Locate the battery compartment on the back of the handset.
3. Plug the battery pack cord into the jack inside the compartment.
NOTE: It is important to maintain the polarity (black and red wires) to the jack inside the
compartment. To ensure proper battery installation, the connector is keyed and can be
inserted only one way.
4. Insert the battery pack.
5. Close the battery compartment by pushing the door up until it snaps into place.
6. Place the handset in the charging cradle.
Allow the handset to charge for 16 hours prior to first use. If you don’t properly charge the
handset, battery performance is compromised.
Connections & Setup
BLACK WIRE
RED WIRE
BA TTER Y
PRESS DOWN
FIRM LY
12
Installing the Headset Battery
CAUTION: To reduce the risk of fire or personal injury, only use Thomson Inc. approved
Li-polymer battery model 5-2707.
NOTE: You must connect the headset battery before use.
1. Locate battery which is packaged inside a plastic bag and separate from the
headset.
2. Open the battery compartment door on the headset.
3. Insert the battery pack.
4. Plug the battery pack cord into the jack inside the compartment.
NOTE: It is important to maintain the polarity (black and red wires) to the jack inside the
compartment. To ensure proper battery installation, the connector is keyed and can be
inserted only one way.
5. Close the battery compartment by pushing the door up until it snaps into place.
6. Attach the foam cover.
7. Place the headset in the charging cradle.
Allow the headset to charge for 16 hours prior to first use. If you don’t properly charge the
headset, battery performance is compromised.
Connections & Setup
13
Headset Set Up
Headband Attachment
1. Hold the headband and insert it into keyed slot marked with an arrow on the
headset.
NOTE: To ensure proper installation, the connector is keyed and can only be inserted one way
2. Rotate the L-shaped band 90 degrees clockwise.
3. Align the L-shaped band into the hole on the headset.
Connections & Setup
14
To switch from ear to ear
Rotate microphone boom to reposition nearer to mouth.
Connections & Setup
15
Ear Clip Attachment
1. Attach the ear clip ring to the headset and ensure all three contact points align
and are engaged.
Connections & Setup
2. Insert ear clip into either side of ear clip ring, matching with the L or R marked
on ear clip ring to fit either your left or right ear.
To switch from ear to ear
Unplug the ear clip from ear clip ring.
Insert the ear clip to ear clip ring with L mark for Left ear.
Insert the ear clip to R mark for Right ear.
Rotate microphone boom to reposition nearer to mouth.
16
CID/Vol 6
(Caller ID/Volume
button)
Redial/Format
(button)
Talk
(button)
Prog/Flash
(program/flash
button)
*Exit
(button)
Mem
(memory button)
#Pause
(button)
display
Off
(button)
Handset Layout
Mute/Del
(mute/delete
button)
CID/Vol 5
(Caller ID/Volume
button)
Headset
(button)
VM
(Voicemail
indicator)
Connections & Setup
17
Vol 3 or 4
(Volume button)
Charge
indicator
Talk/Off
(button)
Headset Layout
Connections & Setup
Charge
contact
18
Handset Set Up
There are six programmable menus available: Display Language, Tone/Pulse
Dialing, Local Area Code, Ringer Tone, Ringer Volume and Factory Default.
When you program these settings, make sure the phone is OFF (not in talk mode).
Pressing the *Exit button will remove you from the menu selection process without
changing the feature you are in.
Display Language
1. Press the Prog/Flash button until 1ENG 2FRA 3ESP shows in the display.
2. Use the CID/Vol ( 5 or 6 ) buttons or the handset number pad to select
1.ENGLISH, 2.FRANCAIS, or 3.ESPANOL. The default setting is 1ENG.
3. Press the Prog/Flash button to confirm. You will hear a confirmation tone.
Tone/Pulse Dialing
1. Press the Prog/Flash button until 1TONE 2PULSE shows in the display.
2. Use the CID/Vol ( 5 or 6 ) buttons or the handset number pad to select
(1) TONE or (2) PULSE. The default setting is TONE.
3. Press the Prog/Flash button to confirm. You will hear a confirmation tone.
Area Code
1. Press the Prog/Flash button until - - - SET AREA CODE shows in the display.
2. Use the handset touch-tone pad to enter your three digit area code. - - - is the
default setting.
3. Press the Prog/Flash button to confirm. You will hear a confirmation tone.
Connections & Setup
19
Ringer Tone
1. Press the Prog/Flash button until RINGER TONE 1 shows in the display.
2. Use the CID/Vol ( 5 or 6 ) buttons or the handset number pad to select
and listen to a ringer tone. There are seven ringer tones to choose from. The
default setting is 1.
3. Press the Prog/Flash button to confirm. You will hear a confirmation tone.
Ringer Volume
1. Press the Prog/Flash button until RINGER VOL 1HI shows in the display.
2. Use the CID/Vol ( 5 or 6 ) buttons or the handset number pad to select 1 (HI),
2 (LOW), or 3 (OFF). The default setting is 1HI.
3. Press the Prog/Flash button to confirm. You will hear a confirmation tone.
Default Setting Selection
1. Press the Prog/Flash button until DEFAULT 41NO shows in the display.
2. Use the CID/Vol ( 5 or 6 ) buttons or the handset number pad to select 1 (NO),
or 2 (YES). The default setting is 41NO. If you choose NO, the current settings
remain. If you choose YES, the unit resets to the factory defaults.
3. Press the Prog/Flash button to confirm.
Connections & Setup
20
Telephone Operation
Making a Call
On the Handset
1. Press the Talk button on the handset to get a dial tone.
2. When finished, press the Off button on the handset to hang up.
On the Headset
1. Press the Talk/Off button on the headset OR the Headset button on the handset
to get a dial tone.
2. When finished, press the Off button on the handset OR the Talk/Off button on
the headset to hang up.
Answering A Call
On the Handset
1. When the phone rings, pick up the handset and press the Talk button to answer
the call.
2. When finished, press Off button on the handset to hang up.
On the Headset
1. When the phone rings, pick up the headset and press the Talk/Off button OR
press the Headset button on the handset to answer the call.
2. When finished, press the Talk/Off button on the headset OR the Off button on
the handset to hang up.
Operation
21
Call Transfer
During a call this feature allows you to transfer the call back and forth from
handset to headset.
1. Press the Headset button on the handset or the Talk/Off button on the headset,
the call will then be transferred from handset to headset.
2. Press the Talk button on the handset, the call will then be transferred back from
headset to handset.
Mute
To have a private, off-line conversation use the mute feature. The party on the
telephone line will not hear you, but you can still hear them.
On the Handset or Headset
1. Press the Mute/Del button on the handset. MUTE ON will blink intermittently,
along with the call status, in the display on the handset.
2. Press the Mute/Del button again to cancel mute and return to your phone
conversation.
Redial
When the phone is on (in TALK mode), press the Redial/Format button to redial the
last number you dialed (up to 32 digits). If you get a busy signal, and want to keep
dialing the number, just press Redial/Format again (you do not have to turn the
phone off and back on).
Operation
22
Flash
Use the Prog/Flash button to activate custom calling services such as call waiting or
call transfer, which are available through your local phone company.
TIP: Do not use the Talk button to activate custom calling services such as call waiting, or you
will hang up the phone.
Exit
Press the *Exit button to cancel any command you initiated.
Handset Volume
While talking, press the CID/Vol ( 5 or 6 ) buttons to adjust the listening level of
the handset’s earpiece. There are four volume levels. Press the 5 button to increase
the volume level, and press the 6 button to decrease. VOL 1 is the lowest level and
VOL 4 is the loudest.
Headset Volume
To Adjust Volume from Headset:
While talking, the headset receiver volume can be adjusted by pressing the Vol
( 3 or 4 ) buttons. The volume can be increased or decreased, step by step up to
4 levels. When maximum level or minimum level is reached, an error tone is emitted.
The last setting is kept when re-cradled. The headset volume level shows on the
handset LCD.
To Adjust Volume from Handset:
The headset receiver volume shall be adjusted by pressing the CID/Vol ( 5 or 6 )
buttons on handset. The volume is increased or decreased step by step up to 4 levels.
The volume level shows on handset. The last setting is kept when re-cradled.
Operation
23
Operation
Paging the Handset and Headset
Press the Page button on the wall base. The handset and headset will beep and the
in use indicators on both will flash for two minutes (or until page is terminated.)
To terminate page signal:
Press the Page button on the wall base.
OR
Press any button on the handset or headset.
NOTE: If there is an incoming call, the handset will automatically terminate the page signal
and play ring tone.
In Use Indicator Light
On the Handset
The handset in use indicator light is lit when the handset is on. It flashes when a call
is received, if there is a Message Waiting (VM) or if the Page button on wall base is
pressed.
On the Headset
The headset in use indicator light is lit when the headset is on. It flashes when a call
is received, if the Page button on the wall base is pressed, if you have a low battery
or are attempting to charge the unit without a battery.
Charger Indicator Light
The charge indicator light is lit when the handset or headset is charging in its cradle
on the charger.
24
Operation
Call Timer
The built-in call timer shows in the display and counts the call time in minutes and
seconds.
Temporary Tone Dialing
This feature is useful only if you use pulse dialing service. Temporary tone dialing
enables pulse (rotary) service phone users to access touch-tone services offered by
banks, credit card companies, etc. For example, when you call your bank you may
need to enter your account number. Using the temporary tone feature allows you to
temporarily switch to touch-tone mode so you can enter and send your number.
1. Press the Talk button, dial the telephone number (i.e. bank or credit card
company), and wait for the line to connect.
2. When your call is answered, press the *Exit button on your handset number pad
to temporarily change from pulse dialing to tone dialing.
3. Follow the automated instructions to get the information you need.
4. Hang up the handset and the phone automatically returns to pulse (rotary)
dialing mode.
25
Caller ID
Caller ID
This unit receives and displays information transmitted by your local phone company.
This information can include the phone number, date, and time; or the name, phone
number, date, and time. The unit can store up to 99 calls for later review.
Caller ID with Call Waiting
Provided you subscribe to Caller ID with Call Waiting service from your phone
company, you are able to see who is calling when you hear the call waiting beep.
The caller identification information appears in the display after you hear the tone.
• Press the Prog/Flash button to put the current person on hold so that you can
answer the incoming call.
IMPORTANT: I
n order to use the Caller ID functions with this unit, you must subscribe to
either the standard Name/Number Caller ID Service or Call Waiting Caller ID Service. To know
who is calling while you are on the phone, you must subscribe to Call Waiting Caller ID Service.
Receiving and Storing Calls
When you receive a call, the information is transmitted by the phone company to
your Caller ID telephone between the first and second ring.
When the memory is full, a new call automatically replaces the oldest call in
memory. NEW appears in the display for calls received that have not been reviewed.
NOTE: Check with your local phone company regarding name service availability.
Reviewing Records
As calls are received and stored, the display is updated to let you know how many
calls have been received.
• Press the CID/Vol 5 button to scroll through the call records from the oldest to
the newest.
• Press the CID/Vol 6 button to scroll through the call records from the most
recent to the oldest.
NEW CALL #
Caller ID name
Caller ID phone number
Time
Date
New call
26
Caller ID
Transferring CID Records to Memory
You may transfer a Caller ID record to your phone’s memory.
NOTE: It is important that you format CID records correctly before storing in memory. It is not
possible to re-format CID records stored in memory.
1. Use the CID/Vol ( 5 or 6 ) buttons to scroll to the record.
2. Press the Mem button.
3. Press the memory location buttons. You will hear a confirmation tone. For example,
press the number 0 and 1 keys to store the record in memory location 01.
To replace a CID record stored in a memory location with a new CID record:
1. Repeat steps 1 through 3.
2. REPLACE MEMO? shows in the display.
3. Press the *Exit button to exit, or press Mem again and the new CID record
replaces the old CID record in that memory location. You will hear a
confirmation tone.
Deleting Records
Use the Mute/Del button to erase the record currently shown in the display or all
records.
Deleting the Current Record
1. Make sure the phone is OFF (not in TALK mode).
2. Use the CID/Vol ( 5 or 6 ) buttons to scroll to the Caller ID record you want to
delete.
3. Press Mute/Del button. The display shows DELETE?
4. Press Mute/Del again to erase the record. You will hear a confirmation tone. The
display shows DELETED. Then the next Caller ID record shows in the display.
27
Caller ID
Deleting All Records
1. Make sure the phone is OFF (not in TALK mode).
2. Use the CID/Vol ( 5 or 6 ) buttons to display any Caller ID record.
3. Press and hold the Mute/Del button until the unit beeps and DELETE ALL? shows
in the display.
4. Press Mute/Del again to erase all records. You will hear a confirmation tone, and
the display shows NO CALLS.
Dialing a Caller ID Number
1. Make sure the phone is OFF (not in TALK mode).
2. Use the CID/Vol ( 5 or 6 ) buttons to display the Caller ID record you want to
dial.
3. Press the Talk or Headset button on the handset. The number dials
automatically.
Changing the CID Number Format
The format button lets you change the format of the displayed CID number. The
available formats are as follows.
7-digit 7-digit telephone number.
10-digit 3-digit area code + 7-digit telephone number.
11-digit long distance code “1” + 3-digit area code + 7-digit telephone number.
1. Use the CID/Vol ( 5 or 6 ) buttons to scroll to the number you want to call
back.
2. If the number does not dial as shown, press the format button. Repeat if
necessary, until the correct number of digits show in the display.
3. Press the Talk or Headset button on the handset. The number
dials automatically.
28
Memory
Store up to 50 24-digit numbers in memory for quick dialing. This memory feature
is in addition to the 99 Caller ID records that can be stored in the Caller ID memory
log.
Storing a Name and Number in Memory
1. Make sure the phone is OFF (not in TALK mode).
2. Press the Mem button.
3. Press the memory location button (01 through 50 records).
4. Press the Mem button again. The display shows ENTER NAME (up to 15
characters).
NOTE: If you don’t want to enter the name, skip to step 5.
For example, to enter the name Bill Smith, press the two key twice for the letter
B, press the four key three times for the letter I, and press the five key three
times for the letter L. After one second, press the five key three times again for
the second letter L and press the one key to insert a space between the letter L
and S. Press the seven key four times for the letter S, press the six key once for
the letter M, press the four key three times for the letter I, press the eight key
once for the letter T, and press the four key twice for the letter H.
NOTE: If you make a mistake, press the del button to erase a wrong letter, and re-enter the
correct letter.
5. Press the Mem button to save the name. The display shows ENTER TEL NUMBR.
6. Use the handset touch-tone pad to enter the telephone number (up to 24 digits)
you want to store.
7. Press Mem again to store the number. You will hear a confirmation tone.
Memory
Loading...