RCA RS2044 User Manual

EXPORTER Thomson Inc. P. O. Box 1976 Indianapolis, IN 46206-1976 © 2005 Thomson Inc. Trademark(s) ® Registered Marca(s) ® Registrada(s) Marque(s) ® Deposée(s) 55997230 (EN/F/E) www.rca.com Printed In China / Impreso en China
IMPORTADOR Comercializadora Thomson de México, S.A. de C.V. Álvaro Obregón No. 151. Piso 13. Col. Roma. Delegación Cuauhtémoc C.P. 06700. México, D.F. Telefono: 52-55-11-020360 RFC: CTM-980723-KS5
RS2044 EN 1/20/05 4:29 PM Page 2
RS2044
user
manual
It is important to read this instruction book prior to using your new product for the first time. Es importante leer este manual antes de usar por vez primera su euipo.
RS2044 EN 1/20/05 4:29 PM Page 3
FCC Information
EN
FCC Information
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. In accordance with FCC requirements, changes or modifications not expressly approved by Thomson Inc. could void the user’s authority to operate this product. This device generates and uses radio frequency (RF) energy, and if not installed and used properly, this equipment may cause interference to radio and television reception. If this equipment does cause interference to radio or television reception (which you can determine by unplugging the unit), try to correct the interference by one or more of the following measures:
• Re-orient the receiving antenna (that is, the antenna for the radio or television that is " receiving" the interference).
• Move the unit away from the equipment that is receiving interference.
• Plug the unit into a different wall outlet so that the unit and the equipment receiving interference are on different branch circuits. If these measures do not eliminate the interference, please consult your dealer or an experienced radio/television technician for additional suggestions. Also, the Federal Communications Commission has prepared a helpful booklet, "How To Identify and Resolve Radio TV Interference Problems." This booklet is available from the U.S. Government Printing Office, Washington, DC 20402. Please specify stock number 004-000-00345-4 when ordering copies. This product complies with DHHS Rules 21 CFR Subchapter J. Applicable at the date of manufacture.
For Your Safety
The AC power plug is polarized (one blade is wider than the other) and only fits into AC power outlets one way. If the plug won’t go into the outlet completely, turn the plug over and try to insert it the other way. If it still won’t fit, contact a qualified electrician to change the outlet, or use a different one. Do not attempt to bypass this safety feature.
CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.
Have a Blast- Just Not in Your Eardrums Make sure you turn down the volume on the unit before you put on headphones. Increase the volume to the desired level only after headphones are in place.
RS2044 EN 1/20/05 4:29 PM Page 4
FCC Information
EN
The descriptions and characteristics given in this document are given as a general indication and not as a guarantee. In order to provide the highest quality product possible, we reserve the right to make any improvement or modification without prior notice. The English version serves as the final reference on all products and operational details should any discrepancies arise in other languages.
Technical specification
Product: 5CD Audio System Brand: RCA Model: RS2044
Electrical Consumption:
Power Supply: 120V~60Hz Power consumption: 80 Watts
IMPORTER Comercializadora Thomson de México, S.A. de C.V. Álvaro Obregón No. 151. Piso 13. Col. Roma. Delegación Cuauhtémoc C.P. 06700. México, D.F. Telefono: 52-55-11-020360 RFC: CTM-980723-KS5
For Your Records
In the event that service should be required, you may need both the model number and the serial number. In the space below, record the date and place of purchase, and the serial number: Model No. Remote Control No. Date of Purchase Place of Purchase Serial No.
Service Information
This product should be serviced only by those specially trained in appropriate servicing techniques. For instructions on how to obtain service, refer to the warranty included in this Guide.
WARNING: TO PREVENT FIRE
OR ELECTRICAL
SHOCK HAZARD,
DO NOT EXPOSE THIS PRODUCT
TO RAIN OR MOISTURE.
SEE MARKING ON BOTTOM / BACK OF PRODUCT
CAUTION
RISK OF ELECTRIC SHOCK DO NOT OPEN
THE EXCLAMATION POINT WITHIN THE TRIANGLE IS A WARNING SIGN ALERTING YOU OF IMPORTANT INSTRUCTIONS ACCOMPANYING THE PRODUCT.
THE LIGHTNING FLASH AND ARROW­HEAD WITHIN THE TRIANGLE IS A WARNING SIGN ALERTING YOU OF "DANGEROUS VOLTAGE" INSIDE THE PRODUCT.
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER­SERVICEABLE PARTS IN­SIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
Portions based upon Microsoft Windows Media Technologies. Copyright © 1999 Microsoft Corporation. All Rights Reserved. Microsoft, Windows Media, and the Windows Logo are trademarks or registered trademarks of Microsoft Corporation in the United States and/or other countries.
RS2044 EN 1/20/05 4:29 PM Page 5
Safety Precautions
• Never open the cabinet under any circumstances. Any repairs or internal adjustments should be made only by a trained technician.
• Never operate this product with the cabinet removed.
• Do not use your System immediately after transporting it from a cold place to a warm place, as condensation may cause the system to malfunction.
• Keep your unit away from humid areas and abnormally hot places.
• Do not touch the player with wet hands. If any liquid enters the player cabinet, take the player to a trained technician for inspection.
• This compact disc player uses a laser to read the music on the disc. The laser mechanism corresponds to the cartridge and stylus of a record player. Although this product incorporates a laser pick-up lens, it is completely safe when operated according to directions.
• Discs rotate at high speed inside the player. Do not use damaged, warped, or cracked discs.
• Do not touch the pick-up lens which is located inside the disc compartment. To keep dust from collecting on the pick-up lens, do not leave the compartment door open for an extended period of time. If the lens becomes dirty, clean it with a soft brush, or use an air blower brush designed for camera lenses.
• The apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids, such as vases, shall be placed on the apparatus.
•Minimum distances around the apparatus for sufficient ventilation .
• The ventilation should not be impeded by covering the ventilation opening with items, such as newspaper,table-cloths,curtains,etc.
• No naked flame sources,such as lighted candles,should be placed on the apparatus.
•Attention should be drawn to the environmental aspects of battery disposal .
Important Battery Information
• Remove the batteries to avoid leakage if you do not use your remote control for more than one month.
• Discard leaky batteries immediately as leaking batteries may cause skin burns or other personal injuries. Dispose of batteries in the proper manner, according to provincial and local regulations.
• Any battery may leak electrolyte under the following circumstances:
- if mixed with a different battery type,
- if inserted incorrectly,
- if all batteries are not replaced at the same
time,
- if disposed of in fire, or
- if an attempt is made to charge a battery not
intended to be recharged.
Headset Safety
• Do not play your headset at high volume. Hearing experts warn against extended high­volume play.
• If you experience ringing in your ears, reduce volume or discontinue use.
• You should use with extreme caution or temporarily discontinue use in potentially hazardous situations. Even if your headset is an open-air designed to let you to hear outside sounds, do not turn up the volume so high that you are unable to hear what is around you.
Don’t Infringe
This product should only be used for the purposes for which it is sold, that is, entertainment, violating no copyright law. Any attempts to use this product for which it is not intended is unlawful and therefore not condoned by Thomson.
Important Information
RS2044 EN 1/20/05 4:29 PM Page 6
1
EN
Table of Contents
FCC Information
Important Information
Table of Contents . . . . . . . . . . . . . . .1
Getting Started . . . . . . . . . . . . . . . .2
Unpacking the system . . . . . . . . . . . . . . . . . . . .2
Back View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Using the FM and Am Antennas . . . . . . . . .2
Connecting the Speakers . . . . . . . . . . . . . . .2
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
General Controls . . . . . . . . . . . . . . .3
Main Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Remote Control . . . . . . . . . . . . . . . . . . . . . . . . .4
Installing Batteries . . . . . . . . . . . . . . . . . . . . .5
Display . . . . . . . . . . . . . . . . . . . . . . .5
Settings . . . . . . . . . . . . . . . . . . . . . .6
Showing Demonstration . . . . . . . . . . . . . . . . . .6
Setting the Clock . . . . . . . . . . . . . . . . . . . . . . . . .6
Setting the Timer . . . . . . . . . . . . . . . . . . . . . . . .6
Activating the Timer . . . . . . . . . . . . . . . . . . .6
Sleep Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Sound Features . . . . . . . . . . . . . . . .7
Volume Control . . . . . . . . . . . . . . . . . . . . . . . . . .7
Bass Boost . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Muting Audio . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Using Preset Equalizer Curves . . . . . . . . . . . . . .7
Creating Custom Curves . . . . . . . . . . . . . . . .7
CD Player . . . . . . . . . . . . . . . . . . . . .8
Important CD and mp3/WMA Information . . .8
Notes on CD-R/RW Discs . . . . . . . . . . . . . . . .8
Notes on mp3/WMA Discs . . . . . . . . . . . . . . .8
Loading Discs . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
Play and Pause Discs . . . . . . . . . . . . . . . . . . . . . .9
Notes on Simple mp3/WMA Playback . . . . .9
Play and Load Simultaneously . . . . . . . . . . .9
Stop Playback . . . . . . . . . . . . . . . . . . . . . . . . . . .9
Selecting a Disc . . . . . . . . . . . . . . . . . . . . . . . . .10
Selecting Folders (mp3/WMA CDs Only) . . . .10
Searching Through a CD . . . . . . . . . . . . . . . . .10
CD Information . . . . . . . . . . . . . . . . . . . . . . . . .10
Sampling Tracks . . . . . . . . . . . . . . . . . . . . . . . .10
Repeat . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
Random Playback . . . . . . . . . . . . . . . . . . . . . . .10
Setting Up a CD Program . . . . . . . . . . . . . . . . .11
Playing a Program List . . . . . . . . . . . . . . . . .11
Displaying the Program List . . . . . . . . . . . .11
Edit Program List . . . . . . . . . . . . . . . . . . . . .11
Deleting Program List . . . . . . . . . . . . . . . . .11
Radio . . . . . . . . . . . . . . . . . . . . . . .12
Selecting Tuner Band . . . . . . . . . . . . . . . . . . . .12
Tuning to a Station . . . . . . . . . . . . . . . . . . . . . .12
Using Presets . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Auto Preset Programming (FM only) . . . . . . .12
Manually Setting Presets . . . . . . . . . . . . . . . . .12
Suppressing Stereo Signal . . . . . . . . . . . . . . . .12
Troubleshooting Tips . . . . . . . . . . .13
Maintenance . . . . . . . . . . . . . . . . .15
Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
CD Player . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
Handling CDs . . . . . . . . . . . . . . . . . . . . . . . . . . .15
Cleaning CDs . . . . . . . . . . . . . . . . . . . . . . . . . . .15
CD Lens Care . . . . . . . . . . . . . . . . . . . . . . . . . . .15
Technical Specification . . . . . . . . . . . . . . . . . . .15
Limited Warranty (U.S.) . . . . . . . . .16
Limited Warranty (Canada) . . . . . .18
RS2044 EN 1/20/05 4:29 PM Page 7
Unpacking the system
You should have the following:
• one main unit (with 2 main speakers);
• one remote control;
• one AM loop antenna;
• one user’s guide;
• one safety leaflet;
• Owner registration Card.
Back View
1. AM Loop antenna Jacks.
2. FM Pigtail Antenna.
3. AUX IN
4. Main Speaker Jacks.
Using the FM and AM Antennas
Before you use your audio system, you’ll want to make sure both the FM and AM antennas are positioned properly. Uncoil the FM antenna at the back of the unit, making sure it is fully extended (you may even want to tape it to the wall behind the unit if possible. The higher the better.) You’ll also need to connect the AM antenna loop to the back of the unit if you listen to AM stations. Rotate the AM loop antenna for better reception.
Connecting the Speakers
Each speaker has a black (negative) and a red (positive) jack. When connecting the speakers, match the red wires to the red jacks and the black wires to the black jacks.
Installation
To ensure sufficient ventilation, keep the spacings shown below free from other surfaces:
2
EN
Getting Started
4 inches
4 inches
Front View
4 inches
4 inches
2
inches
Side View
1
2
3
4
RS2044 EN 1/20/05 4:29 PM Page 8
AM LOOP
FM ANTENNA
MAIN SPEAKERS 6
AUX IN
L+
L
R
-
R+
-
Speaker
NOTE: Make sure the insulation
Wire Connection
Push Speaker terminal tab down to insert wire.
speaker wires at all connection
ends of the
Release tab to lock wire in the terminal.
is completely removed from the
points.
~
3
EN
General Controls
Main Unit
ON/STANDBY - Turns power on or off (STANDBY
mode).
CD INFO - In CD mode - selects among displaying disc details. In simple mp3/WMA mode - Displays the total number of folders and total number of tracks on the current disc when playback is completely stopped; shows the current track number, current folder number and the total time of the current track during playback.
BAND - In Tuner mode - Changes among tuner bands. Enters auto preset program in FM mode. SKIP BACKWARD - In CD mode - Goes to the previous CD track; selects the previous program location. In Tuner mode - Tunes down radio frequency; selects the previous preset station. In Clock or Timer mode - Decreases hour and minute digit. SKIP FORWARD - In CD mode - Goes to the next CD track; selects the next program location. In Tuner mode - Tunes up radio frequency; selects the next preset station. In Clock or Timer mode - Increases hour and minute digit. PLAY / PAUSE - In CD mode - Plays and pauses CD.
STOP - In CD mode - Stops CD playback. In simple mp3/WMA mode - Returns to the first
track on the current disc. In Tuner mode - Sets tune or preset mode. SOURCE - Selects among CD player, tuner and AUX. DEMO - Turns the feature demonstration on or off.
OPEN/CLOSE - Opens or closes the disc tray.
Top View
VOLUME - / + - Adjusts volume. PHONES - Jack for connecting headphones
Tips:
In STANDBY mode, press ON/STANDBY to turn the system on in the previously used mode. Press SOURCE to select the corresponding mode. Look at the display icons to identify the current mode.
RS2044 EN 1/20/05 4:29 PM Page 9
4
EN
General Controls
Remote Control
ON/STANDBY - Turns power on or off (STANDBY
mode). SOURCE - Selects among CD player, tuner and AUX. CLOCK - Enters clock setting mode; shows clock time. PROG/SET - Enters program mode for CD and Tuner. In Clock and Timer setting mode - Applies new settings for Clock and Timer modes. TIMER - Enters timer setting mode; Turns on/ off timer.
EQ - Selects equalizer presets. SLEEP - Press to select the time interval in
minutes before the unit turns off.
B.BOOST - Turns on or off Bass Boost. VOL or - Decreases or Increases volume
level.
STOP - In CD mode - Stops CD playback; In Simple mp3/WMA mode - Returns to the first
track on the current disc. In program mode ­Clears program. In Tuner mode - Sets tune or preset mode.
PLAY/PAUSE - In CD mode - Plays and pauses CD. SKIP BACKWARD - In CD mode - Goes to the previous CD track and setting options; searches backward through CD; In Tuner mode ­Tunes down radio frequency. SKIP FORWARD - In CD mode - Goes to the next CD track and setting options; searches forward through CD; In Tuner mode - Tunes up radio frequency. OPEN/CLOSE - Opens and closes disc compartment.
DISC SKIP - Skips to the next disc in CD mode. REPEAT - Repeats a track, CD or all CDs in CD
mode.
- Turns on/off random listening in CD mode. CD INFO / BAND - In CD mode - selects among displaying disc details. In simple mp3/WMA mode - Displays the total number of folders and total number of tracks on the current disc when playback is completely stopped; shows the current track number, current folder number and the total time of the current track during playback. In Tuner mode - Changes among tuner bands. Enters auto preset program in FM mode. INTRO - Turns intro mode on or off to play the first 10 seconds of each track in CD mode. FM ST • - Selects between stereo and mono sound in FM tuner mode.
MUTE - Mutes audio output.
FOLDER / PRESET / - In Simple mp3/WMA
mode - Goes to the next and previous folder in stop mode. In Tuner mode - Selects next/ previous preset station.
RS2044 EN 1/20/05 4:29 PM Page 10
5
EN
General Controls
X-BASS - X bass is activated.
CLASSIC / ROCK / POP / JAZZ / CUSTOM -
Indicates the preset equalizer selected.
SLEEP - Sleep is activated.
- Timer is activated.
- The corresponding disc icon lights to show which disc compartment is loaded. The current playing disc will flash.
MP3 - mp3 indicator.
WMA - WMA indicator.
STEREO - In FM tuner mode, indicates stereo
sound is selected.
PROGRAM - In program mode.
INTRO - In CD mode, intro is activated so the first
10 seconds of each track will be played.
REPEAT 1 / REPEAT 1 DISC / REPEAT ALL DISC / ALL DISC - In CD mode, indicates the repeat
option that is activated. REPEAT 1 - Repeat track. REPEAT 1 DISC - Repeat current disc. REPEAT ALL DISC - Repeat all disc. ALL DISC - Play all discs once.
- Random playback is activated in CD mode.
- In CD playback mode.
MHz / kHz - Radio frequency unit in tuner mode.
Display
Installing Batteries
The remote control must be inserted with 2 "AAA" or "UM-4" or "R03" batteries prior to use. Follow the steps below to ensure correct installation.
1. Remove the battery compartment door (located at the back of the remote control) by sliding the compartment door in the direction of the arrow and then lifting the door out and off the cabinet.
2. Before inserting the batteries, observe the polarities (that is, + and -) of the battery, then relate the polarities to the engraved diagram inside the battery compartment. Now insert the batteries.
3. After installation of the batteries, replace the battery compartment door in place by sliding it in the opposite direction of the arrow (the reverse of step 1).
RS2044 EN 1/20/05 4:29 PM Page 11
ROCK
STEREO
POP JAZZ
INTRO
PROGRAM
X-BASS
MP3 WMA FOLDER
1
2
3 4 5
CLASSIC
CUSTOM
KHz MHz
SLEEP REPLEAT 1
ALL DISC
1
2
3 4 5
6
EN
Settings
Showing Demonstration
Press DEMO to turn on/off demonstration mode. The demonstration scrolls through all display operations.
Setting the Clock
1. Press and hold CLOCK on the remote control until the hour flashes on the display.
2. Press SKIP BACKWARD or SKIP FORWARD to set the hour and then press CLOCK to shift to minute digits.
3. Press SKIP BACKWARD or SKIP FORWARD to set the minute.
4. Press PROG/SET to save settings and STOP to quit setting.
Setting the Timer
1. Press and hold TIMER on the remote control until the ON and clock hour flashes on the display ( ON - timer on time ).
2. For setting time, press SKIP BACKWARD or SKIP FORWARD to set the hour and then press TIMER to shift to minute digits.
3. Press SKIP BACKWARD or SKIP FORWARD to set the minute.
4. Press TIMER to change to OF (timer off time) with clock time flashing. Repeat steps 2 & 3 for timer off time setting.
5. Press TIMER to select source. Press SKIP BACKWARD or SKIP FORWARD to select between CD / TUNER .
6. Press TIMER to set volume. Adjust VOLUME to select desired volume level.
7. Press PROG/SET on the remote control to save settings. Press STOP to quit setting.
The timer is automatically activated once timer setting is saved.
Activating the Timer
Press and release TIMER to turn on/off the alarm. The timer icon is displayed when timer is activated.
Note:
When system is ON, you can press CLOCK to display the current time for about 2 seconds.
RS2044 EN 1/20/05 4:29 PM Page 12
7
EN
Settings
Sleep Mode
You can select the time interval in minutes before the unit turns off automatically. Press SLEEP to select among OFF, 120, 90, 60, 45, 30, 15 and 5 minutes. The SLEEP icon lights on the display when sleep mode is activated.
View Remaining Sleep Time
When sleep is activated, press SLEEP once to view remaining sleep time.
Adjust Sleep Time
Press SLEEP again when the remaining sleep time is displayed to change sleep time.
Note:
Sleep is automatically de-activated when the unit is turned off.
Sound Features
Volume Control
Adjust VOLUME on the main unit or press VOL
or on the remote control to adjust volume level. The volume level shows briefly on the display to show the change in volume level.
Bass Boost
Press B.BOOST to turn on/off boosting the bass frequency. The BASS icon lights on the display when it is activated.
Muting Audio
Press MUTE on the remote to cut the sound. (Remote Only)
Using Preset Equalizer Curves
Press EQ on the remote control to toggle among FLAT, ROCK, POP, JAZZ, CLASS and CUSTOM. The display shows your selection briefly.
Creating a Custom Curve
1. Press EQ on the remote control to select CUSTOM mode.
2. While CUSTOM is displayed, press SKIP BACKWARD or SKIP FORWARD to cycle among displayed bass- and treble ­range levels.
3. While BAS or TRE is displayed, adjust VOLUME to set the associated gain between -10 - +10.
RS2044 EN 1/20/05 4:29 PM Page 13
8
EN
CD Player
Important CD and mp3/WMA Information
This unit is compatible with CD-RW/ CD-R discs for playback.
Notes on CD-R/RW Disc:
• Do not affix any type of labels to either side (recordable or labeled side) of a CD-R/RW disc as this may result in the unit malfunctioning.
• To avoid damages to the CD-R/RW disc, do not open the disc compartment door while the disc is being read.
• Do not load an unrecorded CD-R/RW disc into the unit. This may take a longer time to read the disc.
• Playback capability for CD-RW discs may vary due to variations in the quality of the CD-RW disc and the recorder used to create the disc.
Notes on mp3/WMA Disc:
• Use .mp3 as the extension when converting audio files into mp3 for saving onto CD-R(W) or CD-ROM, e.g. Abc08.mp3. Do not use any other extension e.g. .doc, .pdf.
• Do not use the .mp3 extension for other text or non-audio data files as this may result in serious malfunction and harmful noise interference.
• For better quality in mp3/WMA disc playback, the CD quality should be recorded 128kbps or above.
• Disc data size > 650MB is not recommended.
• Total files and folders in the disc should not exceed 250, it also depends on the length of the file/folder names.
• For mixed mode discs, only one mode will be selected for playback depending on the recording format.
• To ensure good performance, wait until the disc changer completely reads the disc before proceeding.
• mp3 files in CD ROM EXTRA format disc cannot be recognized.
RS2044 EN 1/20/05 4:29 PM Page 14
CD-R / RW
9
EN
Loading Discs
1. Press SOURCE repeatedly to select CD mode.
2. Press OPEN/CLOSE to open the disc compartment.
3. Insert up to 5 discs with label face up.
4. Press OPEN/CLOSE again to close the disc compartment.
The occupied disc tray icons lights on the display and the current disc icon flashes on the display. The current disc number also shows on the left side of the display. If the disc is a mp3 / WMA CD, the respective mp3 and WMA icon lights on the display.
Play and Pause Discs
• Press PLAY/PAUSE in stop mode to begin playback.
•Press PLAY/PAUSE during playback to pause disc. Press again to resume.
Play and load simultaneously by:
1. Press OPEN/CLOSE to open the disc tray while a CD is playing.
2. Load/change discs for available trays.
3. Press OPEN/CLOSE again to close the tray.
Stop Playback
During playback, press STOP to stop playback.
CD Player
Attention:
Do not push to force closing of the tray during CD playback or tray opening.
Note:
Be sure to remove all discs from the disc compartment before moving or transporting the unit!
Tips:
In stop mode for mp3 and WMA CDs, press STOP to return to the first track of the current disc. The total number of tracks on the current disc is displayed (TT).
Notes on Simple mp3/WMA Playback:
• This unit is compatible with simple mp3/WMA discs. Text information can not be show (e.g. ID3 tags, song name, album, artists, etc.).
• It is strongly recommended that you use a single folder structure for simple mp3/WMA discs. If there are more than only layer of folders, the tracks may be rearranged. (Refer to pg. 17 for simple mp3/WMA playback sequence)
• The first 100 folders from the first 8 folder levels can be read on this unit.
• The unit reads the first 412 files from each discs and the first 255 files in each folder.
RS2044 EN 1/20/05 4:29 PM Page 15
10
EN
CD Player
Selecting a Disc
Press DISC 1 / DISC 2 / DISC 3 / DISC 4 or DISC 5 on the main unit to select disc.
Press DISC SKIP on the remote control to skip discs.
Selecting Folders (mp3 / WMA CDs
Only)
In stop mode,
•Press FOLDER/PRESET to go to the previous folder.
• Press FOLDER/PRESET to go to the next folder.
The folder number (FLD ) shows briefly then the total number of tracks (TT) is displayed.
Searching Through a CD
• Press SKIP BACKWARD / SKIP FORWARD to skip to the previous or
next track.
•Press and hold SKIP BACKWARD / SKIP FORWARD to search through a CD while it is playing.
CD Information
Press CD INFO repeatedly to view the following CD information:
• elapsed track time,
•the current track number (TRK ),
•the current folder number (FLD ) (simple mp3 CDs only),
• the total time of the current track (T).
In stop mode for simple mp3 discs, press CD INFO to view Total Folders (TF) and Total Track (TT) on the current disc.
Sampling Tracks
Press INTRO on the remote control to play the first 10 seconds of each track on the current disc, all discs in the tray, or turn intro mode off. INTRO is displayed when sampling is activated.
Repeat
Press REPEAT on the remote control to repeat the current track (REPEAT 1), current disc (REPEAT 1 DISC) , all discs (REPEAT ALL DISC), or turn repeat mode off (ALL DISC).
Random Playback
Press on the remote control to turn on/off random playback. The icon is displayed when it is activated. All the tracks on one disc will be shuffled and played once before shuffling and playing tracks from the next disc.
Note:
The first 99 tracks of each disc will be shuffled and played once before any of them is repeated.
Tips:
Random playback can be activated simultaneously with repeat 1 disc (randomly play tracks from one disc repeatedly) or repeat all discs (randomly play tracks from all discs repeatedly).
RS2044 EN 1/20/05 4:29 PM Page 16
11
EN
Setting Up a CD Program
1. While the CD player is stopped, press PROG/SET to enter program mode. The system displays the next available program number (-- -- P:01).
2. Press the corresponding disc number on the main unit or DISC SKIP on the remote control to select disc.
3. Press SKIP BACKWARD / SKIP FORWARD to select the track to enter into memory.
4. Press PROG/SET to save your settings.
5. Repeat steps 2 to 4 to store more tracks into program memory.
Playing a Program List
While in PROGRAM mode , press PLAY/PAUSE . If you are not currently in program mode, press PROG/SET to enter program mode before pressing PLAY/PAUSE .
Display Program List
1. While the CD player is stopped, press PROG/SET to enter PROGRAM mode.
2. Press PROG/SET repeatedly to view each track assignment in the program list.
Edit Program List
1. Follow “Display Program List” steps until the location to be edited is displayed.
2. Repeat steps 2 to 4 under “Setting Up a CD Program “ to edit the track to store into memory.
Deleting Program List
While in PROGRAM mode, press and hold STOP for 3 seconds. They system displays the message CLEAR .
CD Player
Tips:
You can create a program of up to 32 tracks.
Note:
Only the first 99 tracks from each disc can be programmed.
RS2044 EN 1/20/05 4:29 PM Page 17
12
EN
Radio
Selecting Tuner Band
1. Press SOURCE repeatedly to enter Tuner mode.
2. Press BAND to select between FM or AM Radio band.
Tuning to a Station
Press SKIP BACKWARD or SKIP FORWARD to select frequencies.
Using Presets
The tuner can be in either TUNE or PRESET mode. When in PRESET mode, the PROG light is on.
• Press STOP to toggle TUNE and PRESET mode.
• Press SKIP BACKWARD or SKIP FORWARD on the main system or FOLDER/PRESET or to access the previous or next preset station. The display first shows the preset program number and after a few seconds, the frequency will be displayed. (FMPR:01 is FM preset 1)
Auto Preset Programming (FM only)
Press and hold the BAND button for 2 seconds to scan stations in FM band. The stations will then be stored as preset channels. A maximum of 32 stations can be stored. Beware of your preset channels being erased accidentally because the scanning and storing process is automatic upon pressing the button. You can stop the automatic scan by pressing any button, but the erased stations cannot be recovered.
Manually Setting Presets
1. Press the STOP button to enter TUNE mode.
2. Press SKIP BACKWARD or SKIP FORWARD to access the desired frequency.
3. Press the PROG/SET button once.
4. The most recently accessed program location will be displayed.
5. If a different program location is preferred, press SKIP BACKWARD or SKIP
FORWARD on the main unit or FOLDER/PRESET or to move to the
desired preset number (1-32).
6. Press PROG/SET to store the selected frequency at that preset.
Suppressing Stereo Signal
Press FM ST to toggle between FM mono and stereo mode. (Remote Only) “STEREO” is displayed in stereo mode.
Tips:
Your audio system has 32 preset stations.
RS2044 EN 1/20/05 4:29 PM Page 18
13
EN
Solution
• Check power cord for a secure connection.
• Unplug the unit for a moment, and then plug into power source again.
• Check the outlet by plugging in another device.
• Increase the volume setting.
• Check connection to speakers.
• Check that you have selected the appropriate function: CD, Tuner.
• Make sure mute is off.
• Make sure headphones are not plugged in.
• Check antenna connection.
• Move antenna.
• Turn off nearby electrical appliances, such as hair dryer, vacuum cleaner, microwave, fluorescent lights.
• Check that CD is in the tray.
• Check that CD label is facing up.
• Check that PAUSE mode is not on.
• Check that CD function is selected.
• Use CD lens cleaner.
• Clean the disc.
• Try another CD.
Problem
System will not turn on
No sound
Poor radio reception
CD does not play
Problem
CD sound skips
CD button will not respond, or does not change discs when you press DISC SKIP
Remote control does not work
Solution
• Clean the disc.
• Check disc for warping, scratches, or other damage.
• Check if something is causing the system to vibrate. If so, move the system.
• Make sure the speakers are at least 3 feet away or on a different surface from the main unit.
• Switch to another function (Tuner) and then back to CD.
• Check that the batteries are properly installed.
• Replace weak batteries.
• Check the system is plugged into power source.
• Point the remote directly at the system’s front panel.
• Move closer to the system.
• Remove any obstacles between the remote and the system.
Troubleshooting Tips
RS2044 EN 1/20/05 4:29 PM Page 19
14
EN
Troubleshooting Tips
Solution
• Check that the mp3/WMA disc is created with a single folder structure. Refer to the diagram below for playback sequence details on multi-level folder structure.
• For example, folders and songs from level 2 are played before moving on to play folders and songs from level 3.
Problem
mp3/WMA playback sequence is out of order
Note:
• Folder playback sequence is indicated by the letters A to G.
• Song playback sequence is indicated by the numbers (1 to 15) in front of the song name.
RS2044 EN 1/20/05 4:29 PM Page 20
LEVEL 1 LEVEL 2 LEVEL 3 LEVEL 4
A
Folder 1
B
Folder 2
C
Folder 3
D
Folder 1.1
E
Folder 1.2
F
Folder 2.1
3 4 5
6
Song 3.1 Song 3.2
7
Song 2.2 Song 2.3 Song 2.4
8
Song 1.1.1
9
Song 1.1.2 Song 1.1.3
10
G
Folder 1.2.1
11
Song 2.1.1
12
Song 2.1.2
13
Song 1.2.1.1 Song 1.2.1.2
14
Song 1.2.1.3
15
1
Song 4 Song 5
2
15
EN
Disconnect the audio system from the power source before performing any maintenance.
Cleaning
Clean the exterior of the system using a soft dust cloth.
CD Player
CAUTION! This system operates with a laser. It must be opened by only a qualified technician.
Handling CDs
• Do not touch the signal surfaces. Hold CDs by the edges, or by one edge and the hole.
• Do not affix labels or adhesive tapes to the label surfaces.
• Do not scratch or damage the label. CDs rotate at high speeds inside the player.
• Do not use damaged (cracked or warped) CDs
Cleaning CDs
• Dirty CDs can cause poor sound quality. Always keep CDs clean by wiping them gently with a soft cloth from the inner edge toward the outer perimeter.
• If a CD becomes dirty, wet a soft cloth in water, wring it out well, wipe the dirt away gently, and then remove any water drops with a dry cloth.
• Do not use record cleaning sprays or antistatic agents on CDs. Also, never clean CDs with benzene, thinner, or other volatile solvents which may cause damage to disc surface
CD Lens Care
When your CD lens gets dirty it can also cause the system to output poor sound quality. To clean the lens you will need to purchase a CD lens cleaner which can maintain the output sound quality of your system. For instructions on cleaning the CD lens, refer to the ones accompanying the lens cleaner.
Technical Specification
Power supply: 120V~60Hz Dimensions ( H x W x D inches): Unit size - 10.5 x 9.9 x 12.9 Speaker - 13 x 9.5 x 8.4 CD player: Response curve (+/- 2dB): 60Hz to 5kHz Rating Plate: Look for it at the back of the set.
Maintenance
RS2044 EN 1/20/05 4:29 PM Page 21
16
EN
Limited Warranty (U.S.)
What your warranty covers:
• Defects in materials or workmanship.
For how long after your purchase:
• One year from date of purchase for labor and parts
• Warranty period for rental units begins with the first rental or 45 days from date of shipment to the rental firm, whichever comes first.
What we will do:
• Pay any Authorized RCA Audio Service Center the labor charges to repair your unit.
• Pay any Authorized RCA Audio Service Center for the new or, at our option, refurbished replacement parts required to repair your unit.
How you get service:
• Take your unit to any Authorized RCA Audio Service Center. To identify your nearest Authorized RCA Audio Service Center, ask your dealer, look in the Yellow Pages, or call 1-800-336-1900.
• Show the Authorized Service Center Representative your evidence of purchase date or first rental.
• Pick up your unit when repairs are completed.
• Proof of purchase in the form of a bill of sale or receipted invoice which is evidence that the product is within the warranty period must be presented to obtain warranty service. For rental firms, proof of first rental is also required.
What your warranty does not cover:
• Customer instruction. (Your Owner’s Manual describes how to install, adjust, and operate your unit. Any additional information should be obtained from your dealer.)
• Installation and related adjustments.
• Signal reception problems not caused by your unit.
• Damage from misuse or neglect.
• Cleaning of audio heads.
• Batteries.
• A unit that has been modified or incorporated into other products or is used for institutional or other commercial purposes.
• A unit purchased or serviced outside the U.S.A.
• Acts of nature, such as but not limited to lightning damage.
Product Registration:
• Please complete and mail the Product Registration Card packed with your product. It will make it easier to contact you should it ever be necessary. The return of the card is not required for warranty coverage.
RS2044 EN 1/20/05 4:29 PM Page 22
EN
17
Limited Warranty (U.S.)
Limitation of Warranty:
• THE WARRANTY STATED ABOVE IS THE ONLY WARRANTY APPLICABLE TO THIS PRODUCT. ALL
OTHER WARRANTIES, EXPRESS OR IMPLIED (INCLUDING ALL IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE) ARE HEREBY DISCLAIMED. NO VERBAL OR WRITTEN INFORMATION GIVEN BY THOMSON INC., ITS AGENTS OR EMPLOYEES SHALL CREATE A GUARANTY OR IN ANY WAY INCREASE THE SCOPE OF THIS WARRANTY.
• REPAIR OR REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS THE EXCLUSIVE REMEDY
OF THE CONSUMER. THOMSON INC. SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING FROM THE USE OF THIS PRODUCT OR ARISING OUT OF ANY BREACH OF ANY EXPRESS OR IMPLIED WARRANTY ON THIS PRODUCT. THIS DISCLAIMER OF WARRANTIES AND LIMITED WARRANTY ARE GOVERNED BY THE LAWS OF THE STATE OF INDIANA. EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ON THIS PRODUCT IS LIMITED TO THE APPLICABLE WARRANTY PERIOD SET FORTH ABOVE.
How State Law relates to warranty:
• Some states do not allow the exclusion nor limitation of incidental or consequential damages, or limitations on how long an implied warranty lasts, so the above limitations or exclusions may not apply to you.
• This warranty gives you specific legal rights, and you also may have other rights that vary from state to state.
If you purchased your unit outside the United States:
• This warranty does not apply. Contact your dealer for warranty information.
Service calls which do not involve defective materials or workmanship are not covered by this warranty. Costs of such service calls are the sole responsibility of the purchaser.
RS2044 EN 1/20/05 4:29 PM Page 23
EN
18
Limited Warranty (Canada)
What your warranty covers:
• Defects in materials or workmanship.
For how long after your purchase:
• One year from date of purchase for labor and parts
• The warranty period for rental units begins with the first rental or 45 days from date of shipment to the rental firm, whichever comes first.
What we will do:
• Pay any Authorized RCA Audio Service Center the labor charges to repair your unit.
• Pay any Authorized RCA Audio Service Center for the new or, at our option, refurbished replacement parts required to repair your unit.
How you get service:
• Take your unit to any Authorized RCA Audio Service Center. To identify your nearest Authorized RCA Audio Service Center, ask your dealer, look in the Yellow Pages, or call 1-800-336-1900.
• Show the Authorized Service Center Representative your evidence of purchase date or first rental.
• Pick up your unit when repairs are completed.
• Proof of purchase in the form of a bill of sale or receipted invoice which is evidence that the product is within the warranty period must be presented to obtain warranty service. For rental firms, proof of first rental is also required.
What your warranty does not cover:
• Customer instruction. (Your Owner’s Manual describes how to install, adjust, and operate your unit. Any additional information should be obtained from your dealer.)
• Installation and related adjustments.
• Signal reception problems not caused by your unit.
• Damage from misuse or neglect.
• Cleaning of audio heads.
• Batteries.
• A unit that has been modified or incorporated into other products or is used for institutional or other commercial purposes.
• A unit purchased or serviced outside Canada.
• Acts of nature, such as but not limited to lightning damage.
Product Registration:
• Please complete and mail the Product Registration Card packed with your product. It will make it easier to contact you should it ever be necessary. The return of the card is not required for warranty coverage.
RS2044 EN 1/20/05 4:29 PM Page 24
EN
19
Limited Warranty (Canada)
Limitation of Warranty:
• THE WARRANTY STATED ABOVE IS THE ONLY WARRANTY APPLICABLE TO THIS PRODUCT. NO VERBAL OR WRITTEN INFORMATION GIVEN BY THOMSON MULTIMEDIA LTD., ITS AGENTS OR EMPLOYEES SHALL CREATE A GUARANTY OR IN ANY WAY INCREASE THE SCOPE OF THIS WARRANTY.
• REPAIR OR REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS THE EXCLUSIVE REMEDY OF THE CONSUMER. THOMSON MULTIMEDIA LTD. SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING FROM THE USE OF THIS PRODUCT. EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE PROVINCIAL LAW, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ON THIS PRODUCT IS LIMITED TO THE APPLICABLE WARRANTY PERIOD SET FORTH ABOVE.
How Provincial Laws relates to warranty:
• This warranty gives you specific legal rights which are in addition to statutory warranties that may vary from Province to Province.
If you purchased your unit outside Canada:
• This warranty does not apply. Contact your dealer for warranty information.
Service calls which do not involve defective materials or workmanship are not covered by this warranty. Costs of such service calls are the sole responsibility of the purchaser.
RS2044 EN 1/20/05 4:29 PM Page 25
Loading...