RCA P61300 User Manual

USER’S GUIDE
highdefinitiontelevisionhighdefi nitiontelevisionhighdefinitiontel evisionhighdefinitiontelevisionhi ghdefinitiontelevisionhighdefinit iontelevisionhighdefinitiontelevi sionhighdefinitiontelevisionhigh definitiontelevisionhighdefinitio ntelevisionhighdefinitiontelevisi onhighdefinitiontelevisionhighd efinitiontelevisionhighdefinition televisionhighdefinitiontelevisio nhighdefinitiontelevisionhighdef initiontelevisionhighdefinitionte levisionhighdefinitiontelevisionh ighdefinitiontelevisionhighdefini tiontelevisionhighdefinitiontelev isionhighdefinitiontelevisionhigh definitiontelevisionhighdefinitio ntelevisionhighdefinitiontelevisi onhighdefinitiontelevisionhighd efinitiontelevisionhighdefinition televisionhighdefinitiontelevisio nhighdefiniti ontele visionhighd ef initiontelevis io nhighde fi nition te levisio n highd e finition t elevisi ionh
Important Information
WARNING
To reduce the risk of fire or shock hazard, do not expose this TV to rain or moisture.
WARNING
RISK OF ELECTRIC
SHOCK DO NOT OPEN
This symbol indicates "dangerous voltage" inside the product that presents a risk of electric shock or personal injury.
Refer to the identification/rating label located on the back panel of your product for its proper operating voltage.
This device complies with part 15 of the FCC rules. Operation is subject to the condition that this device does not cause harmful interference. FCC Regulations state that unauthorized changes or modifications to this equipment may void the user’s authority to operate it. Use of this device without the supplied power cord may cause this set to be non-compliant with FCC part 15 regulations.
If fixed (non-moving) images are left on the screen for long periods, they may be permanently imprinted on the screen. Such images include network logos, phone numbers, and video games. This damage is not covered by your warranty. Extended viewing of channels displaying these images should be avoided.
To reduce the risk of electric shock, do not remove cover (or back). No user serviceable parts inside. Refer servicing to qualified service personnel.
This symbol indicates important instructions accompanying the product.
Cable TV Installer: This reminder is provided to call your attention to Article 820­40 of the National Electrical Code (Section 54 of the Canadian Electrical Code, Part
1) which provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building as close to the point of cable entry as practical.
Product Registration
Please fill out the product registration card and return it immediately. Returning the card allows us to contact you if needed. Keep your sales receipt to obtain warranty parts and service and for proof of purchase. Attach it here and record the serial
and model numbers in case you need them. The numbers are located on the back of the television. Model No. _______________________________________________________ Serial No. ________________________________________________________ Purchase Date: ____________________________________________________ Dealer/Address/Phone: _____________________________________________
Table Of Contents
WELCOME TO HDTV.............................................................4
SETUP AND CONNECTIONS ................................................5
Step 1: Unpack the System ..............................................................6
Step 2: Connect Your TV to Other Components.............................6
Things to Know Before Connecting Components ...................6
Jacks and Cables.........................................................................7
Front of the TV...........................................................................8
Back of the TV..........................................................................10
The Basic Connection...............................................................12
The Advanced Connection ......................................................13
Connecting Speakers to the TV...............................................14
Step 3: Place Batteries in the Remote Control .............................16
Step 4: Plug in and Turn on the System ........................................16
Step 5: Complete the Interactive Setup ........................................16
Step 6: Order Programming .......................................................... 16
USING THE REMOTE........................................................... 17
Remote Control Buttons ................................................................18
Programming the Remote Control ...............................................20
Using the Remote to Control a Component.................................21
Remote Control Codes ...................................................................22
BASIC TV OPERATION........................................................23
About the Channel Banner............................................................24
Changing Between DIRECTV and TV Mode..................................26
Changing Channels ........................................................................27
PIP (Picture-in-Picture) Operation .................................................28
Using the INPUT Button.................................................................30
USING THE PROGRAM GUIDES ........................................ 31
Bringing Up the Program Guides ..................................................32
Anatomy of the TV Program Guide ..............................................33
Anatomy of the DIRECTV Program Guide ....................................34
Getting Around in the Guides.......................................................35
Tuning to a Program ...................................................................... 35
Using the GUIDE Button ................................................................36
1
Table Of Contents
The Other Guides Icon ...................................................................36
Exiting A Program Guide ...............................................................37
Sorting the DIRECTV® Programming Guide..................................38
The Other Icons ..............................................................................42
ADJUSTING TV CONTROLS ...............................................43
Picture Quality Controls................................................................. 44
Picture Settings ........................................................................ 44
Auto Color................................................................................45
Color Warmth ..........................................................................45
Noise Filter ............................................................................... 45
Auto Converge.........................................................................45
Theatre ..................................................................................... 45
Reset Controls .......................................................................... 45
Audio Controls ...............................................................................46
Mute .........................................................................................46
Equalizer...................................................................................46
Speakers ................................................................................... 46
Special Audio ........................................................................... 49
Loudness...................................................................................52
SAP............................................................................................52
Audio Language ...................................................................... 52
USING THE PROFILES ......................................................... 53
About Profiles.................................................................................54
The DIRECTV Setup ........................................................................54
Editing Channels in a DIRECTV List.........................................54
Selecting or Deleting All DIRECTV Channels..........................55
Setting the DIRECTV Spending Limit ......................................55
Setting the DIRECTV Rating Limit...........................................56
The TV Setup ..................................................................................57
Editing Channels in a TV List...................................................57
Selecting or Deleting All TV Channels....................................57
Setting the TV Rating.....................................................................58
The Rating Limit Screen...........................................................59
Blocking Age-Based Ratings....................................................60
Setting the Movie Rating ........................................................62
Blocking Unrated TV Shows ....................................................63
Choosing Your Profile ....................................................................64
2
Table Of Contents
Locking and Unlocking a User Profile...........................................63
Locking the System ........................................................................64
Unlocking the System ..............................................................64
SYSTEM OPTIONS AND PREFERENCES ............................67
Changing the Signal Source ..........................................................68
Changing the Signal Type ..............................................................68
Auto Tuning....................................................................................69
Channel Search...............................................................................70
Mailbox ...........................................................................................70
Purchases: Pay Per View Programs ................................................71
Reviewing and Canceling an
Upcoming Purchase..................................................................74
Setting the Time and Date.............................................................75
Using the Preferences Menu .........................................................75
Using Fetch .....................................................................................78
GETTING ASSISTANCE ........................................................79
Running the Interactive Setup ......................................................80
Getting Antenna Information .......................................................80
The Select Dish Menu Screen.........................................................81
Using the On-Screen Signal Meter.........................................81
Your New Access Card....................................................................82
Running the System Test................................................................82
Off-Air Guides.................................................................................82
REFERENCE...........................................................................83
Troubleshooting ............................................................................. 84
Care and Cleaning..........................................................................85
RCA High Definition Television (HDTV) Limited Warranty ..........86
FCC Registration Information........................................................86
Accessory Information ...................................................................88
Index ...............................................................................................91
3
Welcome to HDTV
High Definition refers to a new way of sending programming information over the airwaves and into your TV. There are two types of TV display formats available. One is ATSC format, which originated from the Advanced Television Systems Committee. The other is NTSC format, which is named for the National Television System Committee. What makes your High Definition Television (HDTV) special is that it has tuners capable of receiving ATSC and NTSC formats as well as digital satellite signals. You can receive: analog (in NTSC format), digital terrestrial (in ATSC format), cable (in NTSC and ATSC formats), and digital satellite. This TV makes receiving all types of signals seamless. Below is an example of how your HDTV can receive the different types of signals.
SATELLITE
TERRESTRIAL ANTENNA (DIGITAL AND ANALOG)
OR
TERRESTRIAL
TOWER SENDING DIGITAL SIGNALS
SATELLITE DISH ANTENNA*
ANTENNA
HDTV
CABLE TV
TOWER SENDING ANALOG SIGNALS
So why is it called High Definition? Definition—commonly called resolution—refers to the sharpness of the image and is determined by the number of dots, or pixels, your screen uses to create the image. The more pixels the sharper the image. An HDTV normally has either 1080 or 720 rows and over 1,000 columns of pixels. This results in a display of over one million pixels. Your HDTV also has a wide screen, or “wide aspect ratio” of 16:9 as opposed to the common 4:3 ratio. It is normally capable of displaying both interlaced images (like today’s analog TVs) and progressive images (like a computer monitor).
What this all means is that while digital broadcasting will bring many new possibilities, only people with HDTVs like yours will actually be capable of realizing many of them. A wide aspect ratio, one million pixel resolution, CD-quality audio with Dolby Digital surround sound, and improved interactivity are features of many digital broadcasts, and your HDTV will help bring it all into your home.
* The appearance of your satellite dish antenna may differ from that shown here.
4
Setup and Connections
Getting Started
This section tells you how to get your HDTV set up
and connected. It describes the cables you will need,
explains the front and back panels, and walks you
through the steps needed to start using your TV.
Setup and connections
1
Setup and connections
Setup and connections
1
1
Interactive Setup
Using the Remote
Interactive Setup
2
2
2
➣➣➣
Using the remote
Basic TV Operation
Using the remote
3
3
3
Using The Program Using the Menu System
4
4
5
Guides
Features and Controls
Adjusting TV Controls
Features and Controls
5
5
6
6
6
7
8
9
Reference
Using the Profiles
Reference
➣➣
System Options and Preferences
Getting Assistance
Reference
5
Setup and Connections
Step 1: Unpack the System
Make sure to locate the remote control and power cord.
Step 2: Connect Your TV to Other
ONOFF
DVD
VCR2
MUTE SKIP
CH
VOL
CH
GUIDE INFO
OK
MENU CLEAR
123
456
789
INPUT
0
REVERSE PLAY FORWARD
RECORD
STOP PAUSE
PIP SWAP CH CTRLWHO
TVVCR1
AUX
DIRECTV
+
VOL
GO BACKFETCH
ANTENNA
Components
During the satellite dish antenna installation, the TV may have been connected with just a coaxial cable for the system test. Depending on what components you have, another connection may provide better picture and audio quality. The following sections provide cable and connection information to help you decide what connection is best for you.
Things to Know Before Connecting Components
Protect Your Components from Power Surges
Connect all components before plugging any power cords into the wall outlet.
Always turn off the TV and other components before you connect or disconnect
any cables.
Position Cables Correctly to Avoid Audio Hum or Interference
Insert all cable plugs firmly into their jacks.
Place the audio/video cables to the sides of the TV’s back panel instead of
straight down the middle after you connect your components.
Remote Control
Power Cord
Try not to coil any twin-lead cables; keep them away from the audio/video cables
as much as possible.
Make sure all antennas and cables are properly grounded. Refer to the safety
sheet packed with your unit.
Protect Your Components from Overheating
Do not block ventilation holes in any of the components. Arrange the
components so that air can circulate freely.
Do not stack components.
Allow adequate ventilation when placing your components in a stand.
Place an amplifier on the top shelf of the stand so that heated air rising from it
will not flow around other components.
6
Setup and Connections
Jacks and Cables
Below is a description of the jacks and cables you can use to make connections. Note that not all cables come with your television unit.
S-Video Jack and Cable
The S-Video jack provides the best picture quality for your system.
This jack is available on this TV and is used in conjunction with audio cables. Remember also to connect the left and right audio cables because the S-Video jack carries only the picture signal, not the sound.
Audio/Video Jacks and Cables (RCA-type)
The audio/video jacks provide very good picture and stereo sound quality.
Theses jacks are used for most audio/video connections between components. The audio/video jacks are often color coded (yellow for video, red for right audio, and white for left audio). If your component has only one input for audio (mono), connect it to the left (white L/Mono) audio jack on the TV.
S-Video Jack
Audio/Video Jacks
RF Jacks and Coaxial Cables (F-type)
The RF jacks are necessary for reception of off-air broadcasts, cable, and DIRECTV signals.
These jacks are required for antenna or cable connections. The RF and coaxial jacks on the TV are labeled SATELLITE IN, ANTENNA A IN, and ANTENNA B IN. An RG-6 coaxial cable is required for all satellite signal distribution.
Optical Jack and Cables
The optical cable is used for connecting a Dolby Digital receiver. If you own a Dolby Digital receiver that uses an optical cable-type input, you can use an optical cable to connect the TV to that receiver for the best sound quality.
Telephone Jack and Cord
The telephone line cord is required to connect your TV to a phone line. If you choose to subscribe to DIRECTV line connection. The phone line connection is used to periodically call out to DIRECTV. You will need an RJ11 type modular jack, which is the most common type of phone jack and might look like the one pictured here. If you don’t have a modular jack, call your local telephone company to find out how to get one installed.
®
programming, some services require this phone
RF Jack
Digital Audio
Out Jack
Phone Jacks
7
Setup and Connections
Front of the TV
The diagrams below describe the front panel and front input jacks on the TV.
POWER MENU/OK TV/DIRECTV INFO
CH
VOL
VOL
CH
POWER Turns the TV on and off.
MENU/OK Brings up the main menu. When in the menu system, it selects highlighted
items.
VOL < Decreases the volume. When in the menu system, VOL < moves the highlight left and adjusts menu controls.
VOL > Increases the volume. When in the menu system, VOL > moves the highlight right and adjusts menu controls.
CH v Scrolls down through the current channel list. If you are in TV mode and press CHv, you scroll down through TV channels. If you subscribe to DIRECTV
®
programming and are in DIRECTV mode, you scroll down through DIRECTV channels. In the menu system, CHv moves the highlight down and adjusts menu controls.
CH ^ Scrolls up through the channel list. If you are in TV mode and press CH^, you scroll up through TV channels. If you subscribe to DIRECTV
®
programming and are in DIRECTV mode, you scroll up through DIRECTV channels. In the menu system, CH^ moves the highlight up and adjusts menu controls.
If you cannot find your remote control, you can use the front panel of the TV to operate many of the TV’s features.
TV/DIRECTV Toggles between TV mode and DIRECTV mode.
INFO Brings up the on-screen channel banner. Press when in the program guide to
get more information on the highlighted program or channel.
S-VIDEO VIDEO L/MONO R
INPUT 4
AUDIO
HEADPHONE
INPUT 4 Lets you connect a baseband NTSC (analog) component such as a VCR, Internet access device, game, or camcorder.
S-VIDEO Lets you connect an S-Video cable for better video quality picture to a component with S-Video capability, such as a VCR. When using S-Video, make sure to connect the two audio cables as well as the S-Video connector.
VIDEO Provides video connection. The video connector is usually yellow.
AUDIO L/MONO Provides left audio connection. The left audio
connector is usually white. R AUDIO Provides right audio connection. The right audio
connector is usually red.
HEADPHONE Provides a connection for headphones.
8
Setup and Connections
Making Connections to the Front Panel
You can connect one of many types of devices to the TV’s front panel, such as a video game or camcorder for playback.
To connect a device to the front panel:
1. Open the small front panel door protecting the INPUT 4 jacks.
2. Connect the device’s audio/video outputs to the INPUT 4 audio and video jacks on the TV.
3. If the device has S-Video capability, connect an S-Video cable (instead of the video cable) from the device to the S-VIDEO jack on the TV. If not, skip this step.
4. Press the INPUT button on the remote control until FRNT (or SFRNT if you have connected an S-Video cable) appears in the channel banner.
Below is an example of how you might connect a camcorder for playback.
S-VIDEO VIDEO L/MONO R
INPUT 4
P O
W E
R
M E
N U
/ O K
T V /
C
D
H
I R
E C
T V
I N F
O V O L
V O L
C
H
S
­V I D
E O
V I
D E O
L / M O
N O
R
H E A
D P H
O N
E I N P
U T
4
A U D
I O
AUDIO
V I D E O
A U D
I
O
HEADPHONE
9
Setup and Connections
Back of the TV
The diagram below describes each of the back panel jacks found on the TV. When connecting A/V cables, be sure to connect corresponding outputs and inputs (video to video, right audio to right audio, etc.).
SATELLITE
IN
ACCESS
CARD
DIGITAL
PHONE
JACK
ANTENNA B
IN
ANTENNA A
IN
AUDIO OUT
FRONT SPEAKER
+ +
R
_
+
R
_
REAR SPEAKER
INT.
FRONT SPEAKER
EXT.
TRANSMITTER OUT
LR
LR
FIX/VARIABLE OUT
L
_
+
L
_
LFE/SUB WOOFER
S-VIDEO S-VIDEO
VIDEO
VIDEO
VIDEO
OUT
AUDIO
AUDIO
INPUT 1 INPUT 2 INPUT 3
AUDIO
SATELLITE IN Use to connect the satellite dish antenna to the TV.
ACCESS CARD Insert the access card into the slot so your program provider can
identify you. Make sure the contacts on the access card are facing left and the top of the card is facing right while inserting. (Refer to “New Access Card” in this manual’s “Assistance” section for details.) The DIRECTV System requires a valid card.
PHONE JACK Use to connect a phone line to the TV. The DIRECTV System requires a continuous phone line connection to periodically call out to program providers.
DIGITAL AUDIO OUT Use a digital optical cable (or SPDIF cable) to connect your TV to a compatible Dolby Digital receiver or decoder. Dolby Digital offers theatre­quality sound (six audio channels). You will not be able to use this jack and the LFE/ SUBWOOFER OUT simultaneously.
ANTENNA B IN Use to connect an off-air or terrestrial antenna or cable TV signal to the TV.
ANTENNA A IN Use to connect a second off-air or terrestrial antenna or cable TV signal to the TV.
You can also use the ANT B IN (or ANT A IN) for video games and switch between the two inputs using the ANTENNA button on the remote control. When using TV games, computers, and similar products with your TV, keep the contrast at a low setting. If a fixed (non-moving) pattern is left on the screen for long periods of time at a high contrast setting, the image can be permanently imprinted onto the picture tubes. These types of imprints are not covered by your warranty because they are the result of misuse.
SATELLITE
IN
ACCESS
CARD
PHONE
JACK
ANTENNA B
IN
ANTENNA A
IN
DIGITAL
AUDIO OUT
10
Setup and Connections
FRONT and REAR SPEAKER Terminals Use to connect external speakers for front sound and rear surround sound.
FRONT SPEAKER INT. / EXT. (switch) Set to INT. if you want to use the internal TV speakers only or the interal TV speakers plus separate rear speakers. Set to EXT. if you want to use any combination of front external speakers. This switch does not turn off the TV center speaker.
TRANSMITTER OUT Use to connect an optional component such as a wireless audio transmitter. Audio volume from the main front and rear speakers is variable audio.
FIX/VARIABLE OUT Use to connect an audio receiver or amplifier (an auxiliary baseband component) for variably-controlled or fixed level stereo output. When set to fixed (via the Audio Output choice in the Speakers menu), a fixed-level audio signal is provided, making these jacks ideal for audio recording or for use with an audio amplifier that has its own remote control.
LFE/SUBWOOFER OUT Use to connect a LFE (Low Frequency Effects) powered subwoofer. This jack is tailored for carrying low frequency information. You will not be able to use this jack and the DIGITAL AUDIO OUT (an optical output) simultaneously.
EXT.
INT.
FRONT SPEAKER
L
_
+
L
_
REAR SPEAKER
FRONT SPEAKER
LR
LR
LFE/SUB WOOFER
OUT
+ +
R
_
+
R
_
TRANSMITTER OUT
FIX/VARIABLE OUT
To specify how you have set up your speakers, press MENU on the remote control and choose Audio. Then choose Speakers… from the menu. For details, see the section “Adjusting TV Controls” in this book.
INPUT 1 Lets you connect a baseband NTSC (analog) component such as a VCR, laserdisc player, Internet access device, or DVD player.
• R AUDIO provides right audio connection. The right audio connector is usually red.
• L AUDIO provides left audio connection. The left audio connector is usually white.
• VIDEO provides composite video connection. The video connector is
usually yellow.
• S-VIDEO lets you connect an S-Video cable for better video quality
picture to a component with S-Video capability, such as a VCR or DVD player. When using S-Video, make sure to connect the two audio cables, as well as the S-Video connector.
INPUT 2 Provides connection to a second NTSC (analog) video component such as a VCR or laserdisc player. Its jacks are the same as described for INPUT 1, above.
INPUT 3 Provides connection to a third NTSC (analog) video component, such as a VCR or laserdisc. Its jacks are the same as described for INPUTS 1 and 2, except with no S-Video jack.
S-VIDEO S-VIDEO
VIDEO
AUDIO
INPUT 1 INPUT 2 INPUT 3
VIDEO
LLL
RRR
AUDIO
VIDEO
AUDIO
11
Setup and Connections
The Basic Connection
TV and VCR
SATELLITE DISH ANTENNA
CABLE OR ANY ALTERNA TE RF SIGNAL, SUCH AS A DIGITAL OR ANALOG TERRESTRIAL ANTENNA
CABLE OR OFF-AIR ANTENNA
TV
SATELLITE
IN
ACCESS
PHONE
JACK
ANTENNA B
IN
ANTENNA A
IN
VCR
CARD
DIGITAL
AUDIO OUT
+ +
R
_
+
R
_
INT.
FRONT SPEAKER
EXT.
TRANSMITTER OUT
FIX/VARIABLE OUT
VIDEO
FRONT SPEAKER
L
_
+
L
_
REAR SPEAKER
LR
LFE/SUB WOOFER
LR
OUT
R
OUT
L
S-VIDEO S-VIDEO
VIDEO
AUDIO
INPUT 1 INPUT 2 INPUT 3
IN FROM ANT
OUT TO TV
VIDEO
AUDIO
How to view programming:
To watch cable TV or off-air TV programs from an antenna in this connection, press ANTENNA on the remote control until ANTENNA A is displayed in the channel banner.
To watch cable or any other alternate RF signal, such as digital or analog terrestrial, press ANTENNA on the remote control until ANTENNA B is displayed in the channel banner.
To watch satellite programming, press DIRECTV on the remote control and channel up or
VIDEO
AUDIO
CH CH
down to the desired program.
How to view your VCR:
Press INPUT on the remote control and select the video input (in this example, VID1) in the channel banner. Because the digital decoder is in the TV, not the VCR, digital channels cannot be recorded. If an off-air antenna is used, the VCR output should be viewed using one of the video inputs.
Some cable systems may require a “conversion box.” If so, consult your cable company’s box tuning instructions for details.
12
NOTE: Viewing a VCR while in AIR mode may result in poor picture performance. Instead, select System Options from the main menu, then select Signal Type and select Cable.
The ANT B and ANT A jacks can receive digital or analog RF signals. The illustrations here are recommended connections in a cable environment.
Setup and Connections
The Advanced Connection
TV, VCR, and DVD Player With Amplifier
DVD
SATELLITE DISH ANTENNA
AMPLIFIER WITH OPTICAL INPUT
CABLE OR ANY ALTERNA TE RF SIGNAL, SUCH AS A DIGITAL OR ANALOG TERRESTRIAL ANTENNA
CABLE OR OFF-AIR ANTENNA
DIGITAL
AUDIO IN
TV
SATELLITE
IN
ACCESS
CARD
PHONE
JACK
ANTENNA B
IN
ANTENNA A
IN
DIGITAL
AUDIO OUT
S-VIDEO
+ +
R
_
+
R
_
INT.
FRONT SPEAKER
EXT.
TRANSMITTER OUT
FIX/VARIABLE OUT
VIDEO
FRONT SPEAKER
L
_
+
L
_
REAR SPEAKER
LR
LFE/SUB WOOFER
LR
OUT
OUT
R
L
S-VIDEO S-VIDEO
VIDEO
VIDEO
AUDIO
AUDIO
INPUT 1 INPUT 2 INPUT 3
VIDEO
AUDIO
After you have made your connections, program the TV to tune to the correct video input channel to see and hear audio and video from the attached component (VCR, DVD player, etc.). Program your TV as described in the “System Options and Preferences” section of this book.
How to view your DVD and VCR:
To watch the VCR in this connection, press INPUT on the remote control until the correct video input appears (in this example, VID1). Note that because the digital decoder is in the TV, not the VCR, you cannot record digital channels.
To watch the DVD player in this connection, press INPUT on the remote control until the correct video input appears (in this example, S-VID2).
VCR 1
Some cable systems may require a “conversion box.” If so, consult your cable company’s box
VIDEO
OUT
IN FROM ANT
L
R
OUT TO TV
CH CH
tuning instructions for details.
Please Read Before Using the Digital Audio Out Jack
This TV’s optical digital output jack fully complies with the international standard governing this type of jack (IEC958), and is designed for connection to a Dolby Digital (AC-3 or PCM) receiver or Dolby Digital (AC-3 or PCM) decoder. Older equipment, some of which is not fully compliant with IEC958, may not be compatible with the Dolby Digital bitstream. Such a connection using anything other than Dolby Digital AC-3 or PCM receiver or decoder could create a high noise level, causing damage to headphones or speakers.
13
Setup and Connections
Connecting Speakers to the TV
You can connect up to four additional speakers to the TV: two to the FRONT SPEAKER terminal, and two to the REAR SPEAKER terminal.
1. If necessary, remove the vinyl covering from the ends of the speaker wire and twist the wire core.
2. Open the lever on the speaker terminal.
3. Insert the wire core into the hole. Be sure to connect the (+) to (+) and (-) to (-).
4. Close the lever. Pull gently on the wire to see that it’s connected securely.
To specify how you have set up your speakers, press MENU on the remote control and choose Audio. Then choose Speakers… from the menu. For details, see the section “Adjusting TV Controls” in this book.
Connecting Front (Main) Speakers
To connect external front speakers:
1. Connect speakers to the FRONT SPEAKER terminal.
2. Set the speaker switch (labeled FRONT SPEAKER) to EXT. to indicate you would like to use the connected external speakers.
Connecting Rear Speakers
To connect rear speakers for surround sound effects:
1. Connect speakers to the REAR SPEAKER terminal.
2. Position the speakers behind you in your TV room. To improve the surround sound effect, you may prefer to set or mount the speakers several feet off the ground.
INT. EXT.
FRONT SPEAKER
L
_
+
L
_
REAR SPEAKER
FRONT SPEAKER
LR
LR
LFE/SUB WOOFER
OUT
+ +
R
_
+
R
_
TRANSMITTER OUT
FIX/VARIABLE OUT
When connecting the speaker wire, make sure you connect the positive (+) terminal on the TV to the positive (+) terminal on the speaker. One side of the speaker wire is usually marked with a white stripe to help you match the terminals correctly. If the (+) and (-) terminals are not matched properly, the speakers will not be “in phase,” causing reduction in bass frequencies.
14
Do not allow the wire core to touch other wires or terminals. Damage to components could result if the cores of two wires touch.
Setup and Connections
Connecting a Subwoofer
To connect a subwoofer to the TV:
1. Connect the subwoofer’s audio input to the LFE/SUBWOOFER OUT jack. Note that if
you use the DIGITAL AUDIO OUT jack and set the Optical Output to anything other than Off, the LFE/SUBWOOFER OUT jack is disabled. If this is the case, you should connect the subwoofer to an A/V receiver instead of the HDTV.
Connecting a Wireless Transmitter
To connect a wireless transmitter (for wireless speakers, wireless headphones, etc.):
1. Connect the transmitter’s audio input to the TRANSMITTER OUT jack. Make sure to
connect the right audio cable to the right audio jack and the left audio cable to the left audio jack. The right audio connector is usually red and the left audio connector is usually white.
2. Specify that you have connected a wireless transmitter by pressing MENU on the
remote control, selecting Audio, then Special Audio, then Wireless Audio. Select the appropriate variable audio output. For more information, see the section in this book, “Adjusting TV Controls.”
Connecting a Stereo Amplifier
1. Connect the amplifier’s TV audio inputs to the left and right FIX/VARIABLE OUT jacks.
2. You may prefer to turn off the TV’s internal speakers by selecting a speaker
configuration with external speakers. Select Audio from the main menu and then select Speakers.
Important: Do not use the amplifier’s PHONO inputs. Consult the amplifier’s owner’s manual for the manufacturer’s recommended hookup.
TRANSMITTER OUT
LR
LFE/SUB WOOFER
OUT
LR
FIX/VARIABLE OUT
The FIX/VARIABLE OUT jacks on the back panel provide a fixed or variable audio signal. When set to “variable” via the Audio menu, they are ideal for use with an audio amplifier that does not have its own remote volume control. When set to “fixed,” the output volume stays the same no matter how the volume changes on the TV.
LEFT RIGHT
LEFT
SURROUND
Arrange the speakers in your TV room to achieve maximum sound quality.
TELEVISION
CENTER
SUBWOOFER
RIGHT
SURROUND
15
Setup and Connections
Step 3: Place Batteries in the Remote Control
Follow these steps whenever you need to install or change the batteries in your TV’s remote control.
1. Remove the cover from the battery compartment.
2. Insert batteries into the battery compartment, matching the + and – end of each battery.
3. Replace the cover.
Step 4: Plug in and Turn on the System
Plug one end of the power cord into the back of the television as shown on right. Plug the other end into a wall outlet. Be sure to insert the plugs completely.
To turn on the TV, press the TV or ON•OFF button on the remote control or the POWER button on the front panel. It may take several seconds for the TV to turn on.
Step 5: Complete the Interactive Setup
Interactive setup appears when you turn on your TV for the first time. Follow the steps to configure the basics of your system, such as setting up the time and day, searching for available channels, and setting up speakers. To run it again, select Assistance from the main menu, then select Interactive Setup. For more details, see the section “Getting Assistance” in this book.
Step 6: Order Programming
You should decide if you would like to receive DIRECTV® programming*. To receive DIRECTV programming, your satellite dish antenna must be installed and pointed correctly. You must also contact your service provider, DIRECTV.
Programming with DIRECTV: Call 1-800-347-3288
TV
When you order programming, you need to know your access card number. To get the number, select Assistance from the main menu and then select System Test.
Wait for the system to run all of its tests. The access card number is displayed at the end of the system test.
Write the access card number in the space below for easy reference:
* DIRECTV® programming is provided in accordance with the terms and conditions of the DIRECTV Customer Agreement, a copy of which is provided with your first DIRECTV billing statement. DIRECTV is a trademark of DIRECTV, Inc., a unit of Hughes Electronics Corp., and is used with permission.
16
______________________________
Using the Remote
How to Use Your Universal Remote
In this section you will find out how to use your universal remote control. This section:
defines the buttons on the remote control.
describes how you toggle between TV “mode” and DIRECTV “mode.”
shows you how to change between analog terrestrial, digital terrestrial, and DIRECTV channels.
walks you through using the PIP (picture-in­picture) feature.
describes how to program the remote to control other devices such as a VCR.
Important: Because this universal remote can control several different components (TV, VCR, etc.), it uses operational modes triggered by the component buttons. For example, if you want the remote to control the VCR, you would press the VCR button to put the remote into VCR mode so you could control the VCR.
Setup and connections
Setup and connections
1
1
Interactive Setup
Using the Remote
2
2
2
➣➣➣
Using the remote
Basic TV Operation
Using the remote
3
3
3
Using The Program Using the Menu System
4
4
5
Guides
Features and Controls
Adjusting TV Controls
Features and Controls
5
5
6
6
6
7
8
9
Reference
Using the Profiles
Reference
➣➣
System Options and Preferences
Getting Assistance
Reference
17
Using the Remote
Remote Control Buttons
ON•OFF When the remote control is in TV or DIRECTV mode, ON•OFF turns the TV on or off. If in another component mode, (VCR, DVD, etc.) and programmed, the remote will turn the component on and off. When pressed twice within two seconds, all components that are on will be turned off (this feature only works with most RCA, PROSCAN, and GE products).
VCR1 Places the remote control in VCR mode and if auto tuning is enabled, it will turn on the TV and tune to the correct channel for viewing VCR1.
TV Turns on the TV and tunes to the last-viewed TV channel. Also places the remote control in TV mode. Placing the remote in TV mode enables you to access the menu system as well as tune to analog, digital, or cable TV channels.
DVD Places the remote control in DVD mode and if auto tuning is enabled, it will turn on the TV and tune to the correct channel for viewing your RCA, GE, or PROSCAN DVD player.
VCR2 Places the remote control in VCR2 mode and if auto tuning is enabled, it will turn on the TV and tune to the correct channel for viewing VCR2.
LED Light that indicates you’re in programming mode when programming the remote control. Also displays when a valid remote control button is pressed.
AUX Places the remote in auxiliary mode in order to control the component (such as a laserdisc player) that you have programmed it to control. Acts as a “wildcard” button, as it can be programmed to control another VCR, cable box, or an RCA, GE, or PROSCAN audio component.
DIRECTV Places the remote control in DIRECTV mode, turns on the TV, and tunes to the last-viewed DIRECTV channel. If you subscribe to DIRECTV must be in DIRECTV mode to view DIRECTV channels. Placing the remote in DIRECTV mode enables you to access the menu system as well as tune to DIRECTV channels.
MUTE Reduces the TV’s volume to its minimum level. Press again to restore volume.
SKIP Press once before changing channels and the TV will wait 30 seconds and then
return to the original channel. Press repeatedly to add more time. If no other displays are present, pressing CLEAR will cancel the skip timer.
®
programming, you
LED
ONOFF
DVD
VCR2
MUTE SKIP
CH
VOL
GUIDE INFO
MENU CLEAR
123
456
789
INPUT
0
REVERSE PLAY FORWARD
RECORD
STOP PAUSE
PIP SWAP CH CTRL WHO
TVVCR1
DIRECTV
AUX
+
CH
GO BACKFETCH
OK
ANTENNA
VOL
CHAN +/- Scrolls up or down through the current channel list. Press once to change the channel up or down; press and hold to continue changing channels. If you are in TV mode and press CH+/-, you scroll through TV channels. If you subscribe to DIRECTV and are in DIRECTV mode, you scroll through DIRECTV channels.
VOL UP/DOWN Adjusts the TV’s audio volume.
FETCH Brings up the Fetch menu, which is a list of most commonly accessed menu
items.
18
Using the Remote
GO BACK Moves you back and forth between the last two channels selected in either DIRECTV mode or TV mode. For example, if you have been viewing both DIRECTV and TV channels (and thus using both the DIRECTV and TV “modes”), pressing GO BACK while watching a DIRECTV channel moves you back to the last DIRECTV channel you viewed. Pressing it while watching a TV channel moves you to the last TV channel you viewed. In the menu system, pressing GO BACK returns you to the previous menu screen.
GUIDE When in TV mode, brings up the TV program guide. In DIRECTV mode, brings up the DIRECTV through the different types of guides.
INFO Brings up channel and viewing information via the channel banner. Quickly press again to bring up an extended channel banner and press a third time to remove the banner. Press when in the program guides to get more information on the highlighted program or channel.
ARROWS Used to point to different items in the menu system and adjust the menu controls. Also move the PIP window when no menus are on the screen.
OK When in the menu system and other on-screen displays, selects highlighted items.
MENU Brings up the main menu and selects highlighted items. When in using an RCA,
GE, or PROSCAN VCR and in VCR mode, it functions as a PROGRAM button.
CLEAR Removes on screen displays and returns to normal viewing. If no displays are present and the skip timer is set, CLEAR will cancel the timer.
DIGIT BUTTONS (0 - 9) Enters channel numbers and time settings directly though the remote control. For more information on entering digits to change channels, see the section “Basic TV Operation.” When in the menus, the digit buttons can be used to directly select items without using the arrows. 0 can be used to return to the previous menu screen.
®
programming guide. Subsequent presses of the GUIDE button scroll
Don’t worry about getting stuck inside a menu. Pressing the CLEAR button on the remote control takes you out of the menu system.
INPUT Toggles through the available external input sources.
ANTENNA Switches the source of the off-air signal between the HDTV’s ANTENNA A
and B. When in VCR mode, the ANTENNA button also functions as a TV/VCR button.
REVERSE, PLAY, FORWARD, RECORD, STOP, PAUSE If programmed, provides transport control for some remote-controllable VCRs, DVD players, laserdisc players, tape decks, and CD players.
PIP When viewing an analog signal, brings up the small picture-in-picture window. Press again to hide PIP.
SWAP Exchanges the main analog picture with the analog PIP window.
CH CTRL (Channel Control) Selects the picture window (either the main or PIP window)
that will change when you press the CH +, CH -, INPUT, or digit buttons on the remote control.
WHO Toggles through user profiles.
19
Using the Remote
Programming the Remote Control
The universal remote can be programmed to control most brands of remote controllable components, such as VCRs. The remote is already programmed to control most RCA, GE and PROSCAN TVs, VCRs, DVD players, and laserdisc players.
Testing the Remote Control
To determine whether the universal remote control requires programming, turn on a component, such as a VCR, point the remote control at the VCR, and press the VCR1 button. Then press ON•OFF or CH + (channel up) or CH - (channel down) to see if the VCR responds to the remote control commands. If not, it requires programming.
LED
Programming the Remote Control
Using Automatic Code Search
The following instructions can be used to program the remote control. If you want to exit the automatic code search without programming any of your components, press and hold CLEAR until the LED light on the remote control turns off.
1. Turn on the component you want to control (VCR, etc.).
2. Press and hold the button you want to program (VCR1, VCR2, etc.). Note that the AUX button can only be programmed using direct entry (see the next section for details). While holding the component button, press and hold ON•OFF until the LED light on the remote control turns on, then release both buttons.
3. Point the remote control at the component you want it to control.
4. Press and release PLAY, then wait five seconds or until the LED light stops flashing.
At this point the remote control is searching for the correct code to program. If, after five seconds, the component you want to control does not turn off, press PLAY again to tell the remote control to search the next set of codes.
Continue pressing PLAY until the component turns off or you have searched through all of the codes. There are 20 total sets of codes. If the component does not turn off after pressing PLAY 20 times, then the remote cannot control that particular component.
If the component you want to control does turn off:
1. Press and release REVERSE, then wait two seconds. Repeat this step until the component turns back on.
ON OFF
VCR1
VCR2
DVD
L
O
V
You’ll use these buttons when you program the remote to control any component.
The remote may not operate all models of all brands.
C
C
PLAYREVERSE
STOP
TV
DIRECTV
AUX
+
H
V
O
L
H
-
2. To finish, press and hold STOP until the LED light on the remote control turns off.
20
Using the Remote
Using Direct Entry
1. Turn on the component to be programmed.
2. Look up the brand and code number(s) for the component on the code list in the section “Remote Control Codes” on the following page.
3. Press and hold the remote control button you want to program.
4. Enter the code from the code list.
5. Release the button, and then press ON•OFF to see if the component responds to the remote control commands. If it doesn’t, try pressing the component button and then ON•OFF again.
6. If you get no response, repeat these steps using the next code listed for your brand until the component responds to the remote control commands.
Using the Remote to Control a Component
Once the remote has been programmed successfully, you are ready to use it to control your components, such as a VCR, DVD player, or laserdisc player.
To operate the component:
This remote control may not operate all models of the brands that are shown. Use the codes shown in this manual, or on the sheet packed with your remote control.
1. Press the component button (VCR1, VCR2, DVD, or AUX) to set the remote to control the component.
2. Press ON•OFF to turn the component on or off.
3. Use the remote control buttons that apply to that component.
21
Using the Remote
Remote Control Codes
VCR
Admiral ............................................. 2131
Adventura ......................................... 2026
Aiko ................................................... 2027
Aiwa ........................................ 2002, 2026
Akai ................... 2003, 2004, 2005, 2007,
American High 2021
Asha ................................................... 2013
Audio Dynamics 2009, 2010
Audiovox .......................................... 2014
Bell & Howell 2011
Beaumark ......................................... 2013
Broksonic .............................. 2012, 2025
Calix .................................................. 2014
Candle .............. 2013, 2014, 2015, 2016,
Canon .......................... 2021, 2022, 2114
Capehart ................................ 2020, 2110
Carver ............................................... 2062
CCE ........................................ 2027, 2061
Citizen ............ 2013, 2014, 2015, 2016,
Colortyme ....................................... 2009
Colt .................................................... 2061
Craig ................. 2013, 2014, 2023, 2061
Curtis-Mathes 2000, 2002,
........................... 2016, 2018, 2021, 2022,
Cybernex .......................................... 2013
Daewoo ........... 2015, 2017, 2019,2025,
Daytron............................................. 2110
Dbx ......................................... 2009, 2010
Dimensia ........................................... 2000
Dynatech ............................... 2002, 2026
Electrohome ......................... 2014, 2029
Electrophonic 2014
Emerson ..................... 2002, 2012,2014,
..................................... 2015, 2021, 2024,
2025,2026,2029, 2030, 2032, 2033,
2034, 2035, 2036, 2037, 2038, 2039,
........................... 2042, 2044, 2045, 2047,
2065, 2105, 2113, 2116, 2117, 2130
Fisher ................ 2011, 2023, 2048, 2049,
Fuji .......................................... 2021, 2119
Funai ....................................... 2002, 2026
Garrard ............................................. 2026
GE ..................... 2000, 2001, 2013, 2021,
Goldstar ........... 2009, 2014, 2018, 2054,
Gradiente ......................................... 2026
Harley Davidson 2026 Harman Kardon 2009
Harwood .......................................... 2061
Headquarter .................................... 2011
Hitachi .............. 2002, 2055, 2056, 2057,
HI-Q .................................................. 2023
Instant Replay 2021
JCL ..................................................... 2021
JC Penney ........ 2009, 2010, 2011, 2013,
......................... 2022, 2055, 2056, 2058,
Jensen .......................... 2055, 2056, 2111
2008, 2111,2112, 2113
2017, 2018, 2019
2017, 2018,2019,2027
2009, 2013,
2024, 2115
2026, 2027, 2028, 2110
2040, 2041,
2050, 2051, 2052,2118
2022, 2053, 2115, 2120
2121
2107, 2111, 2120, 2122
2014, 2021,
2059, 2060, 2107, 2118
JVC ......................... 2009, 2010, 2011, 2018,
Kenwood .............. 2009, 2010, 2011, 2016,
KLH ........................................................ 2061
Kodak .......................................... 2014, 2021
Lloyd ............................................ 2002, 2026
Logik ....................................................... 2061
LXI .......................................................... 2014
Magnavox .............. 2021, 2022, 2062, 2063,
Magnin .................................................... 2013
Marantz ........................... 2009, 2010, 2011,
................................ 2016, 2018, 2021, 2058,
Marta ...................................................... 2014
Masushita ............................................... 2021
MEI .......................................................... 2021
Memorex ................................... 2002, 2011,
.............................. 2013, 2014, 2021, 2023,
MGA ................................. 2029, 2065, 2113
MGN Technology 2013
Midland .................................................. 2053
Minolta ............................. 2055, 2056, 2107
Mitsubishi ............. 2029, 2055, 2056, 2065,
.............................. 2070, 2071, 2072, 2073,
Montgomery Ward 2075, 2131
Motorola..................................... 2021,2131
MTC ................................. 2002, 2013, 2026
Multitech .............. 2002, 2013, 2016, 2026,
NEC ....................... 2009, 2010, 2011, 2016,
.............................. 2058, 2064, 2076, 2078,
Nikko...................................................... 2014
Noblex ................................................... 2013
Olympus ................................................ 2021
Optimus ...................................... 2014, 2131
Optonica ................................................ 2096
Orion ..................................................... 2035
Panasonic .............. 2021, 2022, 2109, 2125,
Pentax ................... 2016, 2055, 2056, 2107,
Pentex Research 2018
Philco ..................... 2021, 2022, 2062, 2063
Philips .................... 2021, 2062, 2096, 2124
Pilot ........................................................ 2014
Pioneer .................. 2010, 2055, 2080, 2081,
Portland ................ 2016, 2017, 2019, 2110
P
ROSCAN ...................................... 2000, 2001
Protec ..................................................... 2061
Pulsar ...................................................... 2104
Quarter ................................................. 2011
Quartz .................................................... 2011
Quasar ............................. 2021, 2022, 2125
RCA ....................... 2000, 2001, 2003, 2013,
................................ 2055, 2056, 2082, 2083,
................................ 2088, 2089, 2090, 2091,
Radioshack/Realistic 2002, 2011,
.............................. 2021, 2022, 2023, 2026,
Radix ....................................................... 2014
2029, 2049, 2050, 2096, 2131
2058, 2111, 2123
2018, 2058, 2111,2123
2104, 2108, 2124
2062,2064
2026, 2104, 2131
2066, 2067, 2069,
2074, 2106, 2113, 2123
2053, 2061
2018,
2079, 2111, 2123
2126, 2127
2120
2123
2021,
2084,2085, 2086,2087,
2107, 2115, 2120, 2125
2013, 2014
Randex ........................................................ 2014
Ricoh ........................................................... 2128
Runco .......................................................... 2104
Samsung .......... 2005, 2013, 2015, 2033, 2053,
Sanky ................................................ 2131, 2104
Sansui ......................... 2010, 2092, 2111, 2123
Sanyo ..................................... 2011, 2013, 2023
Scott ................ 2012, 2015, 2025, 2032, 2035,
Sears ................ 2011, 2014, 2021, 2023, 2048,
.......................... 2049, 2050, 2051, 2055, 2056,
Sharp ............... 2002, 2017, 2029, 2094, 2095,
Shintom ...................... 2004, 2056, 2061, 2098
Shogun ........................................................ 2013
Signature ......................................... 2002, 2131
Singer ..................................... 2021, 2061, 2128
Sony ................. 2002, 2004, 2098, 2099, 2119,
STS .................................................... 2021, 2107
Sylvania ............ 2002, 2021, 2022, 2026, 2062,
Symphonic ....................................... 2002, 2026
Tandy ................................................ 2002, 2011
Tashiko ........................................................ 2014
Tatung ............................................... 2058, 2111
TEAC ............... 2002, 2026, 2058, 2085, 2111
Technics ........................................... 2021, 2109
Teknika ............ 2002, 2014, 2021, 2026, 2100,
TMK ....................................... 2013, 2024, 2047
Toshiba ............ 2015, 2049, 2051, 2055, 2065,
ToteVision ....................................... 2013, 2014
Unitech ....................................................... 2013
Vector Research 2009, 2010, 2015,
Victor .......................................................... 2010
Video Concepts 2009, 2010, 2015,
Videosonic ................................................. 2013
Wards ............ , 2002, 2013, 2014, 2015, 2021,
.......................... 2029, 2055, 2056, 2061, 2096,
2101, 2102, 2103, 2107, 2116, 2131
XR-1000 ............................... 2021, 2026, 2061
Yamaha ............ 2009, 2010, 2011, 2018, 2058,
Zenith .............. 2004, 2098, 2104, 2119, 2128
2038, 2065, 2093, 2116
2063, 2065, 2124
2112
2107, 2118
2096, 2131
2128
2129
2093, 2116
2016
2016, 2113
2023, 2026,
2111
Cable Boxes
ABC ................. 5002, 5003, 5004, 5005, 5006,
Antronix .......................................... 5008, 5009
Archer ........................ 5008, 5009, 5010, 5011
Cabletenna ................................................. 5008
Cableview ................................................... 5008
Century ...................................................... 5011
Citizen ......................................................... 5011
Colour Voice ................................... 5012, 5013
Comtronics ..................................... 5014, 5015
Contec ........................................................ 5016
Jasco ............................................................ 5011
Jerrold .............. 5003, 5005, 5007,5018, 5023,
Magnavox.................................................... 5025
Memorex .................................................... 5026
Movie Time .......................... 5002, 5027, 5028
5007, 5053
5024, 5046, 5053
NSC .............................. 5002, 5027, 5028
Oak ................................ 5002,5016, 5029
Panasonic ................................ 5048, 5052
Paragon .............................................. 5026
Philips ................ 5011, 5012, 5013, 5019,
Pioneer .................................... 5033, 5034
Pulsar .................................................. 5026
RCA .............................. 5047, 5049, 5052
Realistic ................................... 5009, 5049
Regal ........................................ 5022, 5035
Regency ............................................. 5017
Rembrandt ........................................ 5003
Runco ................................................. 5026
Samsung .................................. 5014, 5034
Scientific Atlanta 5006, 5036,
Signal ........................................ 5014, 5018
Signature ............................................ 5003
SL Marx .............................................. 5014
Sprucer .............................................. 5052
Starcom ........................ 5007, 5018, 5053
Stargate ................................... 5014, 5018
Starquest ............................................ 5018
Tandy .................................................. 5040
Teleview ............................................. 5014
Tocom ........................... 5004, 5023, 5041
Toshiba ............................................... 5026
Tusa ..................................................... 5018
TV86 ................................................... 5027
Unika ............................ 5008, 5009, 5011
United Artists 5002
United Cable .................................... 5053
Universal ............ 5008, 5009, 5010, 5011
Videoway ........................................... 5044
Viewstar ............. 5015, 5025, 5027, 5040
Zenith ........................... 5026, 5050, 5051
5025, 5030, 5031, 5032
5037, 5038
Satellite Receivers
Chapparal ............................... 5056, 5057
Drake ...................................... 5058, 5059
GE ............................................ 5000, 5001
General Instruments 5060, 5061,
Panasonic ........................................... 5075
Primestar ........................................... 5076
PROSCAN ............................. 5000, 5001
RCA ......................................... 5000, 5001
Realistic .............................................. 5063
Sony .................................................... 5072
STS1 .................................................... 5064
STS2 .................................................... 5065
STS3 .................................................... 5066
STS4 .................................................... 5067
Toshiba ............................................... 5068
Toshiba ............................................... 5073
Uniden ................................................ 5069
5062
Audio
(For RCA and Dimensia brands only)
AM/FM ............................................... 4003
Aux ..................................................... 4004
Phono ................................................. 4005
CD ...................................................... 4007
Tape .................................................... 4006
22
Basic TV Operation
The ins and outs of Using Your HDTV
This section tells you about the interactive channel banner, which appears when you change channels or press INFO on the remote.
It also describes how to change channels and modes and how to use PIP (picture-in-picture).
This section gives you a broad, clear view of how to operate the basics of your TV.
Setup and connections
Setup and connections
1
1
Interactive Setup
Using the Remote
Interactive Setup
2
2
2
➣➣➣
Using the remote
Basic TV Operation
Using the remote
3
3
3
Using The Program Using the Menu System
4
4
Guides
Features and Controls
Adjusting TV Controls
Features and Controls
5
5
5
6
7
8
9
Reference
Using the Profiles
Reference
6
6
➣➣
System Options and Preferences
Getting Assistance
Reference
23
BASIC TV OPERATION
About the Channel Banner
The channel banner appears whenever you tune to a channel or press INFO on the remote control. When the banner is displayed, pressing INFO gives extended information. Use the arrow buttons and OK to choose an item in the channel banner.
Channel banner icons represent frequently-used features. Some icons change appearance to show the item’s status or availability.
Program title, start and end time, rating, current audio language, and audio mode availability
Indicates incoming signal aspect ratio and screen format applied to it
Cycles through the audio language choices
Main picture channel number
Channel logo, when available
Takes you to the Main menu
Toggles between TV mode and DIRECTV mode
Locks and unlocks the system or unlocks the video
Please note that when you’re in TV mode, the channel banner will not look the same as when you’re in DIRECTV mode (if you subscribe to DIRECTV programming).
Current antenna
Current date and time
“Family” is one of five selectable profiles
Searches all DIRECTV® programming guides for specific information
Sorts the current DIRECTV programming guide for specific information
Displays mail from program providers
®
24
BASIC TV OPERATION
Channel Banner Icons
Main menu icon When selected, takes you to the main menu.
TV/DIRECTV logo When selected, toggles between TV and DIRECTV viewing. The
highlighted icon indicates the current viewing state.
Green unlock icon Indicates that the system is unlocked. Spending, viewing and other limits can be accessed and changed. When selected, locks the system.
Yellow unlock icon Indicates that a password has been entered to override profile limits. No limits can be accessed or changed. When selected, locks the system.
Red lock icon Indicates that no limits can be accessed or changed. A password is required to override limits or access the system.
Audio language icon If the icon is highlighted while watching a digital (ATSC) or DIRECTV channel, two or more audio languages are available. Selecting the icon repeatedly scrolls through and plays the options.
If the icon is highlighted when watching an analog (NTSC) TV channel, a Second Audio Program (SAP) is available. Selecting the icon will play the SAP for the current channel until the channel is changed.
Highlighted mail icon Indicates that you have a message in your mailbox from your DIRECTV read your mail.
AlphaSort™ (A-Z) icon When selected, allows you to sort currently-listed program titles alphabetically.
Highlighted Scout™ (binoculars) icon When highlighted, indicates a Scout has found a program. If selected when highlighted, you view the Scout’s results. If you select the icon when it is not highlighted, you can set up a Scout to find a program for you.
®
programming provider. Select this icon to access the mailbox and
Press INFO on the remote control twice to view an expanded channel banner that shows a program description (when available).
25
BASIC TV OPERATION
Changing Between DIRECTV and TV Mode
When you change channels by entering numbers with the remote control, you tune to programming that can come from one of three different sources: the DIRECTV satellite (if you have DIRECTV service), a terrestrial off-air antenna, or cable TV. You tune to one of these sources by pressing either TV or DIRECTV on the remote control; then you can enter the channel numbers. The diagrams below show how your remote control communicates with the three sources.
ONOFF
In DIRECTV mode, you tune to channels that come from the DIRECTV satellite signal (if you subscribe to DIRECTV
®
programming). Enter channel numbers that are three or four digits long. If the channel number is three digits, you need to press OK to tune.
DVD
MUTE SKIP
VOL
GUIDE INFO
TVVCR1
DIRECTV
AUX
VCR2
CH
+
VOL
CH
GO BACKFETCH
OK
In TV mode, you tune to channels that carry the terrestrial off-air or cable TV signal.
To tune to an analog channel, enter channel numbers that are up to three digits long. Press OK to tune.
To tune to a digital channel, enter channel numbers that are one, two, or three digits long. If necessary, press the right arrow and enter a subchannel number. These numbers appear in the box to the right of the primary channel number. Press OK to tune.
MENU CLEAR
ONOFF
DVD
MUTE SKIP
VOL
GUIDE INFO
DIRECTV
AUX
VCR2
CH
+
CH
GO BACKFETCH
OK
TVVCR1
VOL
Primary Channel
Subchannel (if necessary)
Right arrow button
26
MENU CLEAR
Loading...
+ 70 hidden pages