RCA MST65BKR User Manual

fl at panel solutions

Tilt Wall Mount for LCD, Plasma, and
LED Displays

Instruction Manual

Specifi cations

Display Size: 37” to 65”
Maximum Load: 165 lb (75kg)
Mounting Pattern: 800 mm x 500 mm (31.5” x 19.7”) max
Tilt Range: 15° down
Profi le: 1.4” (3.5 cm)

Box contents

Upper Wall Plate (x1)
Lower Wall Plate (x1)
Left Plastic Side (x1)
Right Plastic Side (x1)

Warnings

Mount Arm (x2)
Instruction Manual (x1)
Hardware Kit (x1)
Template (x2)

MST65BKR

Fits TVs 37”- 65”

Maximum Load

Capacity – 165 lb (75kg)

1. Read these instructions before you begin. If

you are unsure of any part of the process, contact
a professional contractor or installer for assistance.
Improper installation can result in injury or damage.

2. The wall or mounting surface must be capable of

supporting the combined weight of the mount and
the display; if not, the structure must be reinforced.

3. Locate pipes, wires, or any other hazards in the wall

where you wish to install the mount before drilling.

4. Safety gear and proper tools must be used. Failure

to do so can result in injury or damage.

5. A minimum of two people are required for

installation. Do not attempt to install this mount
alone under any circumstances.

6. Follow all instructions and recommendations

regarding adequate ventilation and suitable
locations for mounting your display. Consult the
owner‘s manual for your particular display for more
information.

CAUTION:

This wall mount is intended for use only with the
maximum weight of 75 kg (165 lbs). Use with heavier
than the maximum weights indicated may result in
instability causing possible injury.

Pour des instructions
en français, se
reporter à la page 6.

Para obtener
instrucciones en
español, consulte la
página 11.

Continues on next page...

Tools required

Phillips-Head Screwdriver or Screw Gun
Electric or Portable Drill
3 mm (1/8”) Drill Bit and Stud Finder for Drywall Installation
8 mm (5/16”) Masonry Bit for Concrete Installation
Level

Hardware kit

(A) M6.3 x 63 Screw (x6)

(B) Washer (x6)

(C) Concrete Anchor (x6)

(D) M6 x 12 Screw (x4)

(E) M6 x 30 Screw (x4)

(F) M8 x 12 Screw (x4)

(G) M8 x 30 Screw (x4)

(H) M6 Washer (x4)

(I) Spacer (x8)

(J) Long Allen Key (x1)

(K) 3/16” Drill Bit

Assembly

Assemble the mount by carefully snapping the right and left
plastic sides onto the upper and lower wall plates, as shown in the
illustration (see Fig. 1). Do not force any of the connections as it may
result in breakage of the plastic parts.

Fig.1

Installation

Part 1A – Mounting to the Wall (Drywall)

IMPORTANT! For safety reasons, this mount must be secured to at least two wood studs no less than 16”

apart. For displays heavier than 50 kg (110 lbs), three studs are recommended. The studs must be capable of
supporting the combined weight of the mount and display.

1. Use a high quality stud fi nder to locate two adjacent studs where you wish to install your mount. Mark both

edges of each stud to help identify the exact center.
NOTE: You must use the center of each stud to avoid cracking or splitting the

wood during installation

2. Place the appropriate mounting template against the wall over the center line of

the marked studs. Make sure the template is level.

3. Drill four 3 mm (1/8”) pilot holes in the wall using the template as a guide. Drill

two holes per stud (see Fig. 2).

4. Remove the template from the wall and place the assembled wall plate against

the wall over the pilot holes.

Fig.2

2