Caution: To reduce the risk of electric shock, do not remove cover (or back). No user serviceable parts
inside. Refer servicing to qualified service personnel.
This symbol indicates "dangerous
voltage" inside the product that
presents a risk of electric shock or
personal injury.
WARNING
To reduce the risk of fire or electric shock, do not
expose this product to rain or moisture. The apparatus
shall not be exposed to dripping or splashing. No objects filled with liquids, such as vases, shall be placed
on the apparatus.
This symbol indicates that this product contains mercury. Special disposal of this product for environmental
reasons may be required under the laws applicable to your jurisdiction. For disposal or recycling
information, please contact your local authorities or the Electronic Industries Alliance: www.eiae.org.
This symbol indicates that this product incorporates double
insulation between hazardous mains voltage and user accessible
parts. When servicing use only identical replacement parts.
This symbol indicates important
instructions accompanying the product.
WARNING
The TV is unstable if it is not properly attached to the
base or mounted to the wall. Please follow the base
or wall mounting instructions provided in the User’s
Guide to ensure your safety.
Refer to the identification/rating label located on the back panel of your product for its proper operating voltage.
FCC regulations state that changes or modifications to this unit not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
Cable TV Installer: This reminder is provided to call your attention to Article 820-40 of the National Electrical Code
(Section 54 of the Canadian Electrical Code, Part 1) which provides guidelines for proper grounding and, in particular,
specifies that the cable ground shall be connected to the grounding system of the building as close to the point of cable
entry as practical.
Important: This television is a table model and is designed to sit on a firm, flat, surface. Don't place the TV on soft
carpeting or similar surface because the ventilation slots on the bottom of the unit will be blocked resulting in reduced
lifetime from overheating. To assure adequate ventilation for this product, maintain a spacing of 4 inches from the top
and sides of the TV receiver and 2 inches from the rear of the TV receiver and other surfaces.
Also, make sure the stand or base you use is of adequate size and strength to prevent the TV from being accidentally
tipped over, pushed off, or pulled off. This could cause personal injury and/or damage the TV. Refer to the Important
Safety Instructions on the next page.
The power button (followed by the power symbol) on this TV and your remote control puts the TV into a very
low-power standby mode but will not completely shut the power off. In order to shut the power off, you will need to
disconnect the power cord from your outlet. Therefore, you should make sure the TV is installed in a way that allows
you to disconnect the power cord when desired.
Product Registration
Please fill out the product registration card (packed separately) and return it immediately. For US customers: Your RCA
Consumer Electronics product may also be registered at www.rca.com/television. Registering this product allows us to
contact you if needed.
Product Information
Keep your sales receipt to obtain warranty parts and service and for proof of purchase. Attach it here and record the
serial and model numbers in case you need them. These numbers are located on the product.
Model No. _____________________ Serial No.____________________ Purchase Date __________________
Dealer/Address/Phone _________________________________________________________________________
Page 3
Important Safety Instructions
S
Important Safety Instructions
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers)
that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one
wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third
prong is provided for your safety. If the provided plug does not fit your outlet, consult an electrician for replacement
of the obsolete outlet.
10.Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the
point where it exits from the apparatus.
11.Only use attachments/accessories specified by the manufacturer.
12.Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the
apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid
injury from tip-over.
13.Unplug this apparatus during lightning storms or when unused for long periods of time.
14.Refer all servicing to qualified service personnel. Service is required when the apparatus is damaged in any way, such
as power-supply cord or plug damage, liquid spilled on or objects falling onto apparatus, rain or moisture exposure,
abnormal operation, or if the apparatus has been dropped.
15.If an outside antenna or cable system is connected to the product, be sure the antenna or cable system is grounded so
as to provide some protection against voltage surges and built-up static charges. Section 810 of the National Electrical
Code, ANSI/NFPA No. 70-1984 (Section 54 of Canadian Electrical Code, Part 1) provides information with respect to
proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna-discharge unit, size
of grounding conductors, location of antenna-discharge unit, connection to grounding electrodes, and requirements for
the grounding electrode. See following example:
ELECTRIC SERVICE
EQUIPMENT
ANTENN A
LEAD IN
WIRE
GROUND CLAM P
ANTENN A
DISCHARGE UNIT
(NEC SECTION 810-20)
GROUNDING CONDUCTOR
(NEC SECTION 810-21)
GROUND CLAMP S
POWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ART 250, PART H)
Page 4
Table of Contents
Important Safety Instructions .................................................................................................................... i
Chapter 1 I Connections & Setup
Things to Consider Before You Connect ....................................................................................... 6
Protect Against Power Surges ...................................................................................................... 6
Instructions at the Beginning of the User's Guide .......................................................................... 6
Position Cables Properly to Avoid Audio Interference.................................................................... 6
Use Indirect Light .......................................................................................................................... 6
Check Supplied Parts ................................................................................................................... 6
Attaching Your TV to the Table Stand ............................................................................................ 7
Mounting Your TV to the Wall ......................................................................................................... 9
Get the Picture .............................................................................................................................. 10
Care and Cleaning ........................................................................................................................ 51
Table of Contents5
Page 6
1 Connections and Setup
Things to Consider Before You Connect
Protect Against Power Surges
• Connect all devices before you plug any power cords into the wall outlet or power strip.
NEVER plug your TV into an outlet that is controlled by a wall switch.
• Tu rn off the TV and/or device(s) before you connect or disconnect any cables.
• Make sure all antennas and cables are properly grounded. Refer to the Important Safety
Instructions.
Instructions at the beginning of the User's Guide
• Protect devices from overheating.
• Don’t block ventilation holes on any of the devices. Arrange the devices so that air can
circulate freely.
• Don’t stack devices.
• If you place devices in a stand, make sure you allow adequate ventilation.
• If you connect an audio receiver or amplifier, place it on the top shelf so the heated air
from it won’t flow around other devices.
Position Cables Properly to Avoid Audio Interference
• Insert each cable firmly into the designated jack.
• If you place devices above the TV, route all cables down one side of the back of the TV
instead of straight down the middle.
• If your antenna uses 300-ohm twin lead cables, do not coil the cables. Also, keep the twin
lead cables away from audio/video cables.
Note: If you need
to replace your remote,
call 1-800-338-0376.
A shipping and
handling fee, and the
appropriate sales
tax, will be charged
upon ordering.
Have your Visa,
MasterCard, or Discover
Card ready.
Use Indirect Light
Don’t place the TV where sunlight or room lighting will be directed toward the screen. Use soft
or indirect lighting.
Check Supplied Parts
Check that the following parts were packed with your product.
2 AA BATTERIES
for models
for models L42FHD38/
L46FHD38/L52FHD38/L40FHD380
REMOTE CONTROL
PART # RC2254701/01
L42FHD37/L46FHD37/L46FHD35
REMOTE CONTROL
PART # RC2254702/01
POWER CORD
Graphics contained within this publication are presentation only.
CABLE MANAGE-
MENT STRAP
Go to Page 7 to
see the parts list
for the table stand
6Chapter 1 Connections and Setup
Page 7
Attaching Your TV to the Table Stand
Note:For model L52FHD38, the Table Stand is preassembled, please go to the
next section.
Your TV comes without the table stand attached so that you can choose to
mount your TV either to its table stand or to a wall (wall mount sold separately). If
you want to mount your TV to the wall, don’t attach the table stand, and instead,
Parts List
for models L42FHD37/L46FHD37/L46FHD35/L42FHD38/L46FHD38/L40FHD380
1 Table Stand Base
4 Size M5 Screws
1 Size M8 Screw1 Hinge Cover
1 Hinge
Step 1
There are two options for the stand assembly:
Option 1: Your TV has been packed upside down in the carton (see Figure 1) to facilitate the attachment of the TV
Table Stand assembly. You just need to remove the bag covering the TV, assemble the Table Stand as noted on
page 8 and then attach the Table Stand to the TV before removing the TV from the carton.
Option 2: Remove the TV bag and place it on a large, flat surface such as a table or countertop. Remove the TV
from the carton and place it face down on the TV bag (see Figure 2). Be sure that the TV is face down to avoid
scratching the screen.
Figure 1
Figure 2
Connections and SetupChapter 1 7
Page 8
Step 2
1. Take the stand base and the hinge.
2. Position the hinge by aligning the slot on the hinge and the
notch on the stand base.
3. Attach the hinge to the stand base with four M5 screws,
from the bottom, with a philips head #2 screwdriver.
Notch
Step 3
Hinge Slot
x4
1. Take the stand base assembly and the hinge cover.
2. Locate the hinge cover by aligning the biggest tab
fastener to the biggest slot on the stand base.
3. Push and fasten the hinge cover to the stand base. Be
sure all 3 tab fasteners snap firmly in place.
Fastener
Slot
Stand Cap
Step 4
Remove the stand cap from the TV cabinet by pushing on the small
tab and pulling out the cap.
8Chapter 1 Connections and Setup
Page 9
Step 5
Attach the fully assembled table stand to the TV
cabinet by inserting the hinge into the cabinet and
aligning the hinge guide to the slot opening.
Step 6
Hinge guide
Slot opening
Secure the table stand to the TV cabinet by tightening
the M8 screw with a philips head #3 screwdriver.
Mounting Your TV to the Wall
To mount your TV to the wall you need to purchase a VESA wall mount
Model L42FHD37/L40FHD380/L42FHD38
Model L46FHD37/L46FHD35/L46FHD38/
L52FHD38
Purchase a VESA 600 x400, M6 screw
Purchase a VESA 600 x400, M6 screw
Caution: Your wall mount
must bear a minimum of
five times the tv’s net
weight without causing
damage.
The VESA number is the horizontal and vertical measurement of the mounting holes. For example,
600x400 means the mounting measurements are 600mm horizontally and 400mm vertically.
Follow the directions included with the wall mount to mount the TV to the wall.
Connections and SetupChapter 1 9
Page 10
Get the Picture
The first part of connecting your TV is to get the picture, also known as the signal. The back
panel of your TV allows you to receive analog and/or digital channels by using the ANTENNA/
CABLE INPUT.
Getting Channels
What You Need
Antenna ("rabbit ears") or outdoor antenna with coaxial cable
OR
Coaxial cable with cable service
A. Do you have an indoor or outdoor antenna? If not, go to step B. If so, plug the antenna or
coaxial cable from the wall outlet into the ANTENNA/CABLE INPUT to receive free off-air
local digital and analog channels.
B. Do you have cable? If so, plug the coaxial cable from the wall outlet into the ANTENNA/
CABLE INPUT to receive your cable channels.
C. Do you have a set-top box? If so, you may need to call your cable company or satellite
service provider. They may recommend special cables to allow you to view digital channels.
What You Need To Know
• Visit www.antennaweb.org for help deciding what type of antenna to use to receive the local
digital channels available to you. By entering where you live, this mapping program tells you
what local analog and digital stations are available using a certain antenna.
• When you are ready to watch channels, the channel banner displays the type of channel
you're viewing. Look for a D at the bottom of the screen for digital channels; look for an A
for analog channels. Go to page 30 for more information.
COAXIAL CABLEOUTDOOR OR INDOOR ANTENNA
10Chapter 1 Connections and Setup
OR
Page 11
Choose Your Connections
There are several ways to connect devices such as DVD players and set-up boxes to your
TV. Please use the following chart to determine which connection is best for you. Proceed to
the appropriate page to connect your TV.
Jacks Used Cable Needed Go to...
Audio R and LVideo
COMPONENT INPUT 1 (CMP1)
AUDIO
L
YPbPrR
Audio R and LY Pr PbComponent VideoAudio
HDMI/DVI
Audio R and L
HDMI
PC INPUT
AUDIOVIDEO
Audio/Video
TM
HDMI
TM
+ HDMI/DVI Adapter +ORAudio
VGA
page 12
pages 12-13
pages 13-14
pages 14-15
Note for US
customers: If you
prefer, we can provide
you with the name of
an Authorized Service
Representative who will
visit your home for a
fee to install your
electronic entertainment system and
instruct you in its
operation.
For details about
this service, call
1-888-206-3359.
For additional
assistance while using
your RCA product,
please visit
www.rca.com/
customersupport.
VGAAudio
Audio
HDMI, the HDMI logo, and High-Definition Multimedia Interface are trademarks or registered trade-
marks of HDMI Licensing LLC.
Input Signal Compatability
Ant/Cable 480i, 480p, 720p, 1080i (NTSC, ATSC, and QAM formats)
Composite Video 480i
S-Video 480i
Component Video 480i, 480p, 720p/60Hz, 1080i/60Hz
PC VGA, SVGA, XGA
HDMI 480i, 480p, 720p/60Hz, 1080i/60Hz, 1080p
Connections and SetupChapter 1
11
Page 12
Don’t forget:
If necessary, connect
antenna or cable to get
a picture. Go to page
10 for instructions.
Connecting a Device with Composite Video (Good)
This connection allows you to connect a device that has a Video Out jack, for example, a
DVD player.
Using the example of a DVD player:
1. If necessary, connect your cable and/or off-air antenna as described on page 10.
2. Connect your yellow video cable. Connect a video cable to the (VID1) VIDEO jack on the
back of the TV and to the VIDEO OUTPUT jack on the DVD player.
3. Connect your red and white AUDIO cables. Connect the AUDIO (red and white) cables to
the (VID1) right and left AUDIO jacks on the back of the TV and to the AUDIO OUTPUT
jacks on the DVD player.
Composite Video Connection
This is an example of a connection using the composite video jack.
1
Red
Yellow
White
COMPOSITE CABLES ARE COLOR
CODED-YELLOW=VIDEO
RED=RIGHT AUDIO; WHITE=LEFT AUDIO
Connecting a Device with Component Video (Better)
This connection allows you to connect a device that has Y Pb Pr jacks, for example, a DVD player.
Using the example of a DVD player:
1. If necessary, connect your cable and/or off-air antenna as described on page 10.
2. Connect your Y Pb Pr component VIDEO cables. Connect three VIDEO cables or special
Y Pb Pr cables to the COMPONENT INPUT 1 (CMP1) Y Pb Pr jacks on the back of the TV
and to the Y Pb Pr outputs on the DVD player.
3. Connect your red and white AUDIO cables. Connect the AUDIO (red and white) cables to
the Component Input 1 (CMP1) right and left AUDIO jacks on the back of the TV and to
the AUDIO OUTPUT jacks on the DVD player.
12Chapter 1 Connections and Setup
Page 13
Component Video Connection
This is an example of a connection using the component video jacks. Go to page 12for
specific instructions.
Don’t forget:
If necessary, connect
antenna or cable to get
a picture. Go to page
10 for instructions.
Green
Red
Blue
COMPONENT VIDEO CABLES
(Y Pb Pr) ARE COLOR CODEDGREEN, BLUE AND RED
AUDIO CABLES ARE COLOR
CODED - RED= RIGHT AUDIO,
WHITE=LEFT AUDIO
Red
White
Connecting a Device with HDMI (Best)
High-Definition Multimedia Interface (HDMI) technology is an uncompressed digital connec-
tion that carries both video and audio data by way of an integrated mini-plug cable. Since
HDMI technology is based on Digital Visual Interface (DVI), the jack on the back of your TV is
also compatible with devices that have a DVI output jack.
Using the example of a set-top box:
If your set-top box has an HDMI jack, connect an HDMI cable. Connect an HDMI cable to
the HDMI2/DVI INPUT jack on the back of the TV (or the HDMI1 jack on the back or HDMI3
on the side of the TV if it is more convenient) and to the HDMI Out jack on the back of the
device.
-OR-
If your set-top box has a DVI jack, connect an HDMI cable and an HDMI/DVI adapter.
1. Connect an HDMI cable to the HDMI2/DVI INPUT jack on the back of the TV.
2. Attach an HDMI/DVI adapter to the end of the HDMI cable, then connect the adapter to
the DVI Out jack on the set-top box.
3. Since you’re using an HDMI/DVI adapter, you need to connect separate AUDIO cables to
the DVI AUDIO right and left jacks on the back of the TV and to the R and L AUDIO jacks
on the back of the device.
Connections and SetupChapter 1 13
Page 14
Don’t forget:
If necessary, connect
antenna or cable to get
a picture. Go to page
10 for instructions.
HDMI/DVI Connection (Best)
This is an example of a connection using the HDMI2/DVI jack. Go to page 13 for specific
instructions.
Note: The maximum
resolution is 1024 x
768. Be sure to set
your PC to the
correct monitor
output setting.
Red
White
HDMI Cable
OR
HDMI Cable + HDMI/DVI Adapter +
Audio cables are color coded
Red=right audio; white=left audio
Connecting a PC Device
This connection allows you to connect to a personal computer and use your TV as a monitor.
1. If necessary, connect your cable and/or off-air antenna as described on page 10.
2. Connect your monitor cable. Connect one end of a 15-pin monitor cable to the PC VIDEO
jack on the TV and the other end to the PC's VIDEO OUTPUT jack. Note, if your PC's
VIDEO OUTPUT isn't 15-pin, you'll need an adapter that can connect to a 15-pin monitor
cable.
3. Connect your AUDIO cable. Connect a 3.5mm stereo mini pin cable (sometimes referred
to as 1/8" stereo mini pin) to the PC AUDIO jack on the back of the TV and the other end
to the AUDIO OUTPUT jack on the PC.
14Chapter 1 Connections and Setup
Page 15
PC Connection
This is an example of a connection using the PC VIDEO jack. Go page 14 for specific
instructions.
Don’t forget:
If necessary, connect
antenna or cable to get
a picture. Go to page
10 for instructions.
Viewing the Picture from the Connected Device
1. Plug in the TV (see page 16 for details) and the device, if they aren't already plugged in.
2. Turn on the TV and the device you want to view, for example a DVD player.
3. Repeatedly press the INPUT button on the remote control until you see VID1 (if connected
to the VIDEO INPUT 1 jacks), CMP1 (if connected to the CMP1 jacks) or HDMI1 (if
connected to the HDMI1 jack) displayed at the bottom of the TV's screen. To go back to
viewing TV channels, use the number buttons to enter the channel you want to view.
Note: If the picture from the DVD player appears black and white and your device is connected to
the VIDEO INPUT, you might be tuned to the wrong input. Make sure you press INPUT until you
see VID1, CMP1 or HDMI1 displayed at the bottom of the TV's screen.
Note:
• If you're done connecting devices to your TV, go to page 17 to complete the Initial Setup.
• To continue connecting devices, go to the next page.
Viewing the PC
1. Plug in the TV and the PC, if they aren't already plugged in.
2. Turn on the TV and the PC.
3. Repeatedly press the INPUT button on the remote control until you see PC displayed at
the bottom of the TV's screen. To go back to viewing TV channels, use the number
buttons to enter the channel or press CH+ or CH- buttons.
Note: If you're done connecting devices to your TV, go to page 17 to complete the Initial Setup.
Connections and SetupChapter 1 15
Page 16
Plug in the TV
Plug the end of the power cord into the back of the TV. Plug the other end into an outlet. Insert
the plug completely into the outlet. Do not plug into an outlet controlled by a light switch.
Put Batteries in the Remote
• Remove the battery compartment cover from the back of the remote by pushing the tab
and lifting off the cover.
• Insert two fresh batteries. Make sure the polarities (+ and -) are aligned correctly.
• Replace the cover.
Turn on the TV
Turn on your TV by pressing the Power button( ) on the side of the TV or ON•OFF on the
remote control.
How to Use the Remote Control to Complete
Note: Highlighted
means that the menu
item stands out from
other menu items on
the list (appears
darker, brighter, or a
different color).
the Initial Setup
The technical term is “Navigation” - how you move through the on-screen menus. The theory
is the same throughout the menu screens: highlight your choice and select it.
To highlight a menu item, press the arrow buttons on the remote to highlight one of the items
listed on the screen. Use the up or down arrow button to move up or down. Use the right or
left arrow button to view other selections for a menu choice or to display a sub-menu.
16Chapter 1 Connections and Setup
Page 17
Complete the Initial Setup
The menu system in your TV allows the TV’s features to work properly. The first time you turn
on your TV, the language screen appears.
Set the Menu Language
The first part of the setup allows you to select your preferred language for the menu system.If
English is your preferred language, press OK and go to set the TV Location Mode. To choose
another language, press the down arrow button until that language is highlighted, and press
the OK button.
Set the TV Location Mode
After choosing the Language, a menu screen will ask you to set the TV Location. Choosing“Home”
for the TV Location assigns the optimal picture settings for most home environments. This is also
the most energy efficient setting. Press OK, the picture mode will automatically be set to “Natural”
and the Channel Setup menu will display.
If choosing “Retail”, which is not Energy Star compliant, press OK to display “Proceed” and
“Go Back”. Choosing “Go Back”, press OK to return to the previous menu which allows the selection
of retail and home modes. If choosing “Proceed”, press OK, the picture mode will automatically be
set to “Vibrant” and the Channel Setup menu will display.
Complete Channel Setup
Make sure you've connected the TV to cable or an off-air signal before you start the next part
of the setup.
Set the Signal Type
From the Channel Setup menu, press the up or down arrow button to highlight Signal Type, if
you connect the Cable to your ANTENNA/CABLE INPUT jack, the option is chosen for you
and you can press the down arrow button to continue. To choose Antenna, press the right
arrow button and then press the down arrow button to continue.
English
Français
Español
TV Location
Home
Retail
Energy Star compliant
Channel Setup
Go Back
Signal Type Cable
Channel Search ...
Complete the Channel Search
With Channel Search highlighted, press OK to begin the channel search. There are several
things to be aware of when the TV searches for channels. If you chose Cable as your signal
type, the search takes a while because it's looking for analog and digital channels, and then
it's removing scrambled channels found. Here is what happens during the search:
1. The search first looks for analog channels and places the number of channels found next
to Analog Channels Found.
2. The search then looks for digital channels and places the number of channels found next
to Digital Channels Found. This number may seem high. This is because the number
includes both scrambled (for example, Pay Per View) and non-scrambled channels. These
channels are dependent upon what your cable company is sending.
3. The search might appear as if it is complete, but as long as the search says Running, it is
still in progress. What's happening now is the TV is removing scrambled channels from the
channel list. When Channel Search is in progress, you can press the CANCEL button to
cancel the search. Any channels already found will be stored.
4. When the search is complete, the Channel Setup menu will display the following help text:
“Channel Search complete. Press OK to review channels, Press CANCEL to exit, MENU
for Setup menu”. If it’s the TV’s first installation, the help text will display like this “Channel
Search complete. Press OK to review channels. Press CANCEL to exit.”
You might find there are still some channels in your list that are unavailable to view. To get rid
of these channels, press MENU and choose Setup. Highlight and select List and Labels.
Note that removing channels from your channel list may be time consuming, so you might
want to do it later. Go to page 38 for details on editing your channel list.
Note:
If you are using a satellite or cable set-top box, you do not need to complete Channel
Search.
Connections and SetupChapter 1 17
Channel Setup
Go Back
Signal Type Cable
Channel Search Runing
Porgress 4%
Analog Channels Found 5
Digital Channels Found 0
Auto Channel Search in progress. Press CANCEL to cancel. Any
channels already found will be stored.
Channel Setup
Go Back
Signal Type Cable
Channel Search ...
Channel Search complete. Press OK to review channels. Press
CANCEL to exit, MENU for Setup menu.
Page 18
What To Expect
Watching TV
• Remember: Look for an A at the bottom of the screen to see if you're watching an analog
channel.
Analog video is sent in a 4/3 format, or your TV can display these channels in a 16/9 format by
pressing the FORMAT button to view the different formats available. Go to page 35 for
more explanation of screen formats.
• Remember: Look for a D at the bottom of the screen to see if you're watching a digital
channel.
Most digital video is sent in a 16/9 format which does fill your screen, but it is sometimes
sent in 4/3 which does not fill your screen. It depends on how the station or source device
is formatting the video. If there are bars on-screen, press the FORMAT button to try adifferent format. This may eliminate the bars. Some bars can't be removed because of
the way the format is sent by the broadcaster. Go to page 35 for more explanation of
screen formats.
Changing Channels
• Digital channels can have both primary channels (like the analog channel number) and
sub-channels. To tune to a digital channel with a sub-channel, such as 10.1, enter the
primary channel number (10), then press the right arrow button. Enter the sub-channel
number (1) and press OK.
• Depending upon the type of signals you have connected to your HDTV, you might notice
that the channels change slower than you’re used to. This is perfectly normal. Digital cable
channels sometimes take longer to tune.
18Chapter 1 Connections and Setup
Page 19
Explanation of Jacks (in alphabetical order)
This section describes the jacks on the back panel of your TV. There are several ways to
connect devices.
ANTENNA/CABLE INPUT Lets you connect a coaxial cable to receive the signal from your
antenna, cable, or cable box.
AUDIO/VIDEO INPUT 1 (VID1) Lets you connect a device that has composite video jacks,
such as a VCR or DVD player.
•
L AUDIO Provides left audio connection when using the VIDEO INPUT 1 jack. The left audio
connectors are usually white. For mono audio sources be sure to use the Left AUDIO INPUT.
•
R AUDIO Provides right audio connection when using the VIDEO INPUT 1 jack. The right
audio connector is usually red.
COMPONENT INPUTS Lets you connect a device that has component VIDEO jacks, such as
a DVD player.
•
CMP1 Y Pb Pr (Component Video) Provides optimum picture quality because the video
is separated into three signals. Use three video-grade or component VIDEO cables for the
connection. When using CMP1 Y Pb Pr, make sure you connect left and right AUDIO cables
to the CMP1 L and R AUDIO jacks.
•
CMP1 L AUDIO Provides left audio connection when using the CMP1 VIDEO inputs. The
left audio connector is usually white. For mono audio sources be sure to use the Left AUDIO
INPUT.
•
CMP1 R AUDIO Provides right AUDIO connection when using the CMP1 VIDEO INPUTS.
The right audio connector is usually red.
•
CMP2 Y Pb Pr (Component Video) Same as described for CMP1 Y Pb Pr and CMP1
AUDIO above. Make sure you connect the left and right AUDIO cables to the CMP2 L and R
AUDIO jacks.
DIGITAL AUDIO OUTPUT (optical) Use a digital optical cable to connect your TV to a
compatible audio receiver.
FIXED AUDIO OUTPUT Use left and right AUDIO cables to connect your TV to a compatible
audio receiver.
HDMI1 INPUT Lets you connect a device, such as a digital cable box, with an HDMI output.
HDMI2/DVI INPUT Lets you connect a device, such as a digital cable box, with an HDMI or
a DVI output.
•
HDMI2/DVI INPUT (High-Definition Multimedia Interface/Digital Visual Interface) Provides
an uncompressed digital connection that carries both video and audio data by way of an
integrated mini-plug cable. Since HDMI technology is based on Digital Visual Interface (DVI),
the jack on the back of your TV is also compatible with DVI devices.
•
DVI AUDIO L (used for DVI only) Provides left audio connection when using the HDMI2
jack for DVI. The left audio connector is usually white. For mono audio sources be sure to use
the Left AUDIO INPUT.
•
DVI AUDIO R (used for DVI only) Provides right audio connection when using the HDMI2
jack for DVI. The right audio connector is usually red.
PC VIDEO INPUT Connect your computer, or other device with a VGA OUTPUT, to this jack
using a 15 pin D-sub cable.
PC AUDIO (Stereo mini jack) Use to obtain sound when a PC is connected to the PC INPUT
Use a 3.5mm stereo mini pin cable (sometimes referred to as 1/8” stereo mini pin) to connect a
PC to your TV.
L
R
DVI AUDIO INPUT
HDMI 2/
DVI
INPUT
HDMI 1
INPUT
AUDIO
PC INPUT
VIDEO
Y
Y
Pb
Pb
Pr
Pr
L
L
AUDIO
AUDIO
COMPONENT INPUT 1 (CMP1)
R
VIDEO
L
AUDIO
R
AUDIO/VIDEO INPUT 1 (VID1)
DIGITAL AUDIO
OUTPUT (Optical)
ANTENNA/CABL
R
L
AUDIO
R
E
COMPONENT INPUT 2 (CMP2)
FIXED AUDIO OUTPUT
Note: Remember to
connect the left and
right AUDIO cables
because the DVI
cable carries only the
picture signal, not the
sound.
Connections and SetupChapter 1 19
Page 20
Note: Do not connect
an S-Video and a
regular video cable to
the side jacks at the
same time.
Buttons and Other Jacks On Your TV
Side Input Jacks
Headphones Allows you to connect headphones to listen to the sound coming from the TV.
VIDEO INPUT 2 Receives video from another device such as a camcorder, video game
console, VCR, or DVD player. To access a device connected to the VIDEO jack, press the
INPUT button on your remote until VID2 appears at the bottom of the screen.
AUDIO L and R Receives audio from another device such as a camcorder, video game
console, VCR, or DVD player. Use when connecting to the VIDEO or S-VIDEO INPUT. For
mono audio sources be sure to use the Left AUDIO INPUT.
S-VIDEO INPUT Allows you to connect an S-Video cable from another device. Make sure
you also connect audio cables from the device to the TV. To access a device connected to the
S-VIDEO jack, press the INPUT button on your remote until VID2 appears at the bottom of the
screen.
HDMI 3 INPUT Lets you connect a device with an HDMI OUTPUT.
USB This connection allows you to plug in a USB flash drive or connect to a compatible mass
storage device with USB.
Side Panel Buttons
If you cannot locate your remote, you can use the side panel buttons of your TV to operate
many of the TV’s features.
POWER Turns the TV on and off.
MENU/(OK) Brings up the TV Main menu. When in the menu system, it displays sub-menus
and selects highlighted items.
VOL Increases the volume. In the TV menu system, it acts like the right arrow button on the
remote control and adjusts menu controls.
VOL Decreases the volume. In the TV menu system, it acts like the left arrow button on the
remote control and adjusts menu controls.
CH Scans up through the channel list. In the TV menu system, it acts like the up arrow
button on the remote control and adjusts menu controls.
CH Scans down through the channel list. In the TV menu system, it acts like the down
arrow button on the remote control and adjusts menu controls.
(FETCH=MENU + VOL ) Press the MENU and VOL at the same time and the remote
control will bark to be located. (This Fetch function is only available for models L42FHD38,
L46FHD38, L52FHD38 and L40FHD380.)
20Chapter 1 Connections and Setup
Page 21
2 Using the Remote Control
Remote Control Buttons
Alphanumeric Buttons Enter channel numbers, time settings, and
options with letters, using these buttons.
To enter a channel, press the number buttons and press OK (or just let the
entry timeout).
To enter a digital channel with a sub-channel, enter the main channel, then
press the right arrow button to enter the sub-channel and press OK.
Arrows( / / / ) Used to highlight different items in the TV menu and to
adjust the menu controls. When viewing a channel, arrow functions are as
follows:
•
Left arrow/FORMAT Press to change the screen format: Normal, Zoom,
Cinerama, Stretch. Go to page 35 for more information on screen formats.
•
Right arrow/GUIDE Press this button first to display the electronic program
guide-EPG (when available), press again to view the program in the schedule.
•
UP arrow/INFO Press this button once to display the channel banner,
press again to remove the menu.
•
Down arrow/PRESETS Press this button to enter the PRESET menu.
Display Picture and Sound preset; CC Setting; Current Audio Track.
CC Takes user directly into the Closed Caption submenu.
CH + or CH - Scans up or down through the current channel list. Press once
to change the channel up or down; press and hold to continue changing
channels.
CH List When you tune to a particular channel, press button to enter the List
and Labels menu directly to add/ remove the channel from channel list.
(FETCH)/CANCEL Cancels the barking when Fetch has been activated.
(This Fetch function is only available for models L42FHD38, L46FHD38,
L52FHD38 and L40FHD380.) Go to page 20 or 35 for more details. Cancel
function: Removes any menu or display from the screen and returns you to
normal viewing.
DVD Places the remote in DVD mode. If Autotuning is enabled, turns on the
TV and tunes it to the DVD Channel. This button lights when you press a valid
button in DVD mode (see Modes of Operation on page 24 for more details).
F1-F4 Favorite channel buttons. You can set one of the favorite channel
buttons (F1/F2/F3/F4) to the current channel by holding the button for a couple
of seconds. Each button can be set to a favorite channel at one time, but you
can change the setting many times.
GO BACK Returns you to the previous channel.
INPUT Accesses the available video input channels (VID1, VID2, CMP1,
CMP2, PC, HDMI1, HDMI2 and HDMI3). To resume TV viewing, press the
number buttons to enter the channel or press CH+ or CH- buttons.
Remote control part number RC2254701/01
This is a multi-device remote control and many of the
buttons have multiple functions.
Note: If you need to replace your
remote, call 1-800-338-0376. A
shipping and handling fee, and the
appropriate sales tax, will be charged
upon ordering. Have your Visa,
MasterCard, or Discover Card ready.
MENU Brings up the Main Menu.
Using the Remote ControlChapter 2 21
Page 22
MUTE Reduces the TV’s volume to its minimum level. Press again to restore the volume.
OK When in the menu system, selects highlighted items.
PIC Press to display the Picture submenus.
ON
•
OFF When in TV mode, turns the TV on or off. If in another mode (SAT
programmed, will turn the device on or off.
REW, REPLAY, PLAY, NEXT, FWD, REC, STOP, PAUSE (buttons at TOP of the remote)
If programmed, provides transport control for some remote-controllable devices, for example,
VCRs or DVD players.
ZZZ (SLEEP) Press to display the Time menu and set Sleep Timer.
SAT
/
AUX Places the remote in SAT/AUX mode. If Autotuning is enabled, turns on the TV and
tunes it to the satellite or cable box Video Input Channel. This button lights when you press a
valid button in SAT/AUX mode (see Modes of Operation on page 24 for more details).
TV Turns on the TV and puts the remote in TV mode. Also displays current status.
V-CHIP Press to display the Parental Control submenu directly.
VOL - or VOL + Decreases or increases the TV’s volume.
/
AUX or DVD) and
Using the INPUT Button
Use the INPUT button to scroll through the available video input channels and view devices
you have connected to the TV.
1. Make sure the device you want to view is turned ON.
2. Press INPUT to tune to an available video input source and view the device.
3. To return to the previous channel, press INPUT until you return to the channel.
Programming the Remote to Operate
Other Devices
The universal remote can be programmed to operate many brands of remote-controllable VCRs,
audio devices, DVD players, cable boxes, satellite receivers and other devices. In addition to
being programmed to operate your television, it’s already programmed to operate some
RCA devices.
Notes:
•
The TV button can’t be programmed on this remote to control any device; it controls only this TV.
•
The remote may not be compatible with all models of all brands of devices. It also may not
operate all functions of your device.
Find Out If You Need to Program the Remote
To determine whether the universal remote needs to be programmed to operate one of the
devices connected to your TV, such as a DVD player, do the following:
1. Turn on the device (in this example, a DVD player).
2. Point the remote at the device.
3. Press the corresponding device button (in this example, DVD player).
4. Press ON•OFF to see if the DVD responds. If the DVD doesn’t respond, you need to
program the remote to operate it.
22Chapter 2 Using the remote control
Page 23
Programming the Remote
The CANCEL button is used as visual feedback during the programming operation. During
programming, the CANCEL button will light up when buttons are pressed and turn off when
buttons are released. When programming is finished, the CANCEL button will long blink to
indicate success and short blink to indicate fail.
Note: All device buttons are off during programming mode.
There are 3 ways to program the remote control to operate other devices: Direct Entry,
Manual Code Search, and Automatic Code Search. If you have recently purchased the device
you want to control or if the device has many codes, you might want to try the manual code
search first.
Using Direct Entry
1. Turn on the device you want to control.
•
2. On your remote control, simultaneously press and hold the ON
(approximately 3 seconds) until the CANCEL button lights up. Then release the buttons.
3. Press and release the device button (SAT/AUX or DVD) you want to program.
4. Enter a 4-digit code from the code list. The first digit indicates the database device type (0
for DVD, 1 for Satellite TV, 2 for Cable, 3 for DVR, 4 for VCR, 5 for Audio, 6 for CD), the
other 3 digits indicate the brand. Look up the brand and code number(s) for the device in
the code list at the end of this section.
5. The CANCEL button will long blink to indicate success. Repeat these steps until you’ve
tested all codes for your device’s brand or try to run a manual code search.
OFF and MUTE buttons
Using a Manual Code Search
Note: Before using manual code search, you must use Direct Entry first. This lets the remote know
which type of device to begin searching codes. Then proceed with the following steps.
1. Turn on the device you want to control.
2. On your remote control, simultaneously press and hold the ON•OFF and MUTE buttons
(approximately 3 seconds) until the CANCEL button lights up. Then release the buttons.
3. Press and release the device button (SAT/AUX or DVD) you want to program.
4. Repeatedly press and release the left arrow or right arrow button, watching for the device
to respond. If it does turn off, press and release the OK button to save the code. The
CANCEL button will long blink to indicate success.
5. When all codes have been searched, the CANCEL button will short blink to indicate fail,
then the remote returns to normal operation.
Note:Use right arrow to search ahead, use left arrow to search back. Or you can press the ON/
OFF button to switch to Auto Code Search mode.
Using Automatic Code Search
1. Turn on the device you want to control.
2. On your remote control, simultaneously press and hold the ON•OFF and MUTE
(approximately 3 seconds) buttons until the CANCEL button lights up. Then release the
buttons.
3. Press and release the device button you want to program.
4. Press and release the ON•OFF button once. The remote starts the code search.
5. Once the device turns off, quickly press the OK button to save the code. The CANCEL
button will long blink to indicate success.
6. When all codes have been searched, the CANCEL button will short blink to indicate fail,
then the remote returns to normal operation.
Note:
If you accidentally passed the code before saving it, press the left arrow button to backtrack
through the codes; then use the right arrow button to go forward through the codes again. Once
the left arrow or right arrow button has been pressed, the search mode changes to Manual Code
Search.
Using the Remote ControlChapter 2 23
Page 24
Note: The remote
control may not be
compatible with all
brands and models
of devices.
How to Use the Remote After You’ve
Programmed It
Once the remote has been programmed successfully, you are ready to use it to operate your
devices.
To operate the device:
1. Press the appropriate device button (SAT
device, for example, press DVD to control your DVD player.
2. Press ON
3. Use the remote buttons that apply to that device.
•
OFF to turn the device ON or OFF.
Modes of Operation
The button corresponding to the mode the remote is in lights up when you press any button
that works in that mode. For example, if you’re in TV mode and you press the VOL+ button,
the TV button lights up. This tells you that the command to increase the volume is being sent
to the TV (and not the satellite receiver, for example).
/
AUX or DVD) to set the remote to control the
24Chapter 2 Using the remote control
Page 25
Manual Reset of the Remote Control
The Manual Reset is used to reset the remote settings to default.
Note: The reset can also be done by replacing the batteries, but replacing the batteries does not
always cause a reset, so you can perform a manual reset if the remote doesn’t reset after battery
replacement.
1. On your remote control, simultaneously press the V-Chip, ON•OFF and MUTE buttons.
2. The CANCEL button will long blink to indicate success, and the remote control returns to
normal operation.
Using the Remote ControlChapter 2 25
Page 26
Remote Code List
Note: The codes are programmable to any of the device buttons (SAT /AUX or DVD) on the remote. The remote code is a 4-digit
code. The first digit indicates the database device type (0 for DVD, 1 for Satellite TV, 2 for Cable, 3 for DVR, 4 for VCR, 5 for Audio
and 6 for CD), the following 3 digits indicate the brands as follows:
WHITE WESTINGHOUSE ................................492
DVD/VCR Combo Codes
Where the code is listed as [### ###] the first is for
the DVD and the second is for the VCR. Otherwise
just the one code operates both the DVD and the
VCR. Remember to add the code for the database
device type 0 for DVD, 4 for VCR, [0### 4###].
ZT Group ..........................................................020
Home Theatre in a Box
Where the code is listed as [### ###] the first is for
the DVD and the second is for the AUDIO. Otherwise just the one code operates both the DVD and
the AUDIO. Remember to add the code for the database device Type, 0 for DVD, 5 for Audio [0### 5###].
ZT Group ........................................................038
Using the Remote ControlChapter 2 29
Page 30
3 Using the TV’s Features
Channel Banner
There are several indicators that might appear when you press the INFO button on the remote.
This display is called the Channel Banner. The following list describes the items on the Channel
Banner screen (left to right and top to bottom).
English720 p 60Unrated
Parental Control
10 CBS 00:25
D
CC Stretch
Z
Z
z
02:16 AM
StereoIf the current channel is analog, Stereo appears when broadcasting in
stereo and Mono appears when the current channel is broadcasting in
mono. If the current channel is digital, this space will be blank.
SAPIf the current channel is analog, this will show it’s broadcasting SAP
(Second Audio Program) information. If the current channel is digital,
this will show language.
720 p 60 Broadcast signal resolution
UnratedRatings information
Parent ControlThe Parent control state of the current program
D 10 CBSThe D means it's a digital channel. If it's an analog channel, A
is displayed. The channel, sub-channel (if available for digital
channels) and program (only for digital channels) you're currently
viewing are displayed.
CCClosed Captioning is available on the current channel.
StretchCurrent screen format. If there are bars on the screen, you might be able
to get rid of them by pressing the FORMAT button on the remote. Go
to page 35 for more information on screen formats.
ZZZ 00:25Current time left on sleep timer, if the sleep timer is set.
02:16 AMCurrent time
Autotuning
Note : This feature
only works with
other RCA devices.
Autotuning
Go Back
Set DVD Channel N/A
Set SAT-AUX Channel N/A
Press < or > to select input for the DVD key.
30Chapter 3 Using the TV’s Features
The Autotuning feature automatically tunes the TV to the correct video input channel for
different devices you have connected to your TV. When you set up Autotuning in the menu
system you don’t have to remember to change your TV to the VID1 input, for example, when
you want to watch a tape on the VCR. To set up the Autotuning feature:
1. Press MENU (the Main Menu appears).
2. Highlight Setup and press OK on your remote control.
3. Highlight Autotuning and press OK.
4. Choose which device button you would like to set:
Set DVD Channel Lets you set up the channel the TV tunes to when you press the DVD button.
Set SAT
SAT
-
/
AUX button.
AUX Channel Lets you set up the channel the TV tunes to when you press the
Page 31
5. Press the left/right arrow button to select the choice that matches the way you have the
device connected to this TV.
You can select from the following inputs or channels:
N/A Choose this if you don’t have a device connected to the TV, or if you don’t want the
TV to automatically tune to the correct channel/input when you’re using this device.
Channel 3 or 4 Device is connected to the ANTENNA/CABLE jack on the back of the TV,
and you want the TV to tune to channel 3 when you press the corresponding button on the
remote. Reminder: make sure the device’s Channel 3/4 switch is set to channel 3.
VID1 or VID2 (Video Input) Device is connected to the VIDEO INPUT 1 jack on the back of
the TV or the VIDEO INPUT 2 jack on the side of the TV and you want the TV to tune to the
VIDEO INPUT channel when you press the corresponding device button.
CMP1 or CMP2 (Component Video Input) Compatible component VIDEO source, such
as an HDTV tuner, satellite receiver, or DVD player, is connected to the three Component
VIDEO INPUT jacks (Y Pb Pr) on the back of the TV and you want the TV to tune to the
component VIDEO INPUT channel (CMP1 or CMP2) when you press the corresponding
device button.
PC Device is connected to the PC INPUT jack on the back of the TV and you want the TV
to tune to the PC input when you press the corresponding device button
HDMI1, HDMI2 or HDMI3 Device is connected to the HDMI1 or HDMI2/DVI INPUT on the
back of the TV or HDMI 3 on the side of the TV, and you want the TV to tune to the HDMI
INPUT channel when you press the corresponding device button.
Parental Controls and V-Chip
The choices in the US V-Chip and Canada V-Chip menus involve software inside your TV
referred to as V-Chip which allows you to block TV programs and movies. TV programs can
be blocked by age-based ratings, such as TV-MA, which is explained on page 32. If
available, TV programs can also be blocked by content, such as adult language (L). This is
explained on page 33. Movies can only be blocked by age-based ratings. This is explained
on page 33. Once you block programs, you can unblock programs by entering a password.
By default, the software inside your TV is turned off or unlocked. For instructions to lock
V-Chip, see page 32.
How V-Chip Works for USA and Canada
V-Chip reads the program’s age-based rating (TV-MA, TV-14, etc.) and content themes [(Violence
(V), Adult Language (L), etc.)]. If you have blocked the rating and/or content themes that the
program contains, you will receive the message This channel is blocked. Change channel or
press OK to enter your password and temporarily deactivate the parental controls.
Broadcasters are not required to provide content themes, so programs received with no con-
tent themes will only be blocked if you block their age-based rating. You can also block out
programs that have been given an Exempt rating, and programs that are considered unrated.
Go to page 46 for the US and Canada ratings explanations.
Note: Parental control
settings are not
available for HDMI1,
HDMI2, HDMI3,CMP1,
CMP2, or PC INPUTS.
These settings must be
set in the connected
device's parental
controls.
Using the TV’s Features Chapter 3 31
Page 32
Parental Control
Go Back
Lock Parental Control - - - -
Select Channel 51 MTV
Block Channel
Block Buttons
US V-Chip
Canada V-Chip
Unrated/Exempt Ratings View
Rating Region Name_12
To lock parental controls, enter 4 digit password using the digit
keys.
Note:If you do not
lock parental
controls, none of the
settings for V-Chip,
Block Channel, or
Block Buttons will
take effect.
Note:If you forget your
password, turn off the
TV. Simultaneously
press and hold VOL
DOWN on the side
panel and CANCEL on
the remote for 10
seconds. Next time
you enter the Parental
Control menu, enter a
new password.
Lock Parental Controls
•
When the Parental Control menu is accessed from the Main menu and the parental controls
are permanently unlocked, the following message is displayed:
“Parental controls are UNLOCKED. Rating limits and Channel block will NOT require a password toview the picture. Use “Lock Parental Control” to lock. Press any key to continue.”
•
Pressing any key displays the Parental Control menu and highlights Lock Parental Control.
•
To lock parental controls, enter a 4 digit password using the digit keys, after password is
entered and parental controls are still unlocked, you must repeat entering the password.
Once password is confirmed, the message is displayed: “Parental Controls are LOCKED.
Blocked programs will require a password to view the picture.”
Unlock Parental Controls
If parental controls are locked or temporarily unlocked, then the Password menu will appear
when the user tries to enter the Parental Control menu. After correct password is entered,
the parental controls are now unlocked.
The V-Chip Rating Screen
The following is an example of where items are located within the TV Ratings option with the
US V-Chip menu.
Rating Status Field
Lets you select whether the status of the agebased rating to the left limit is view or block.
TV Ratings
Go Back
Rating Field
Lets you select
from a list of agebased ratings you
can block or view.
Status D L S V FV
TV-MA
View
View
TV-14
View
TV-PG
TV-G
View
View
TV-Y7
TV-Y
View
Content Themes
Lists the content
themes you can
block or view.
US V-Chip TV Ratings
TV Ratings
Go Back
Status D L S V FV
TV-MA View
TV-14 View
TV-PG View
TV-G View
TV-Y7 View
TV-Y View
Press OK to view/block programs with this rating.
Blocking Age-Based Ratings
You can automatically block all program ratings above a specified age-based rating level.
1. Choose Parental Control from the Main menu. If parental controls have previously been
locked, you must enter your password.
2. Highlight and select US V-Chip. Then select TV Ratings.
3. Press the up or down arrow button to scroll to the rating corresponding with the lowest
rating you do not want the child to watch.
4. Press the OK button to toggle between View and Block. The status for the rating and all
higher ratings automatically changes to Block.
32Chapter 3 Using the TV’s Features
Content Status Fields
Lets you select which content themes to view for
the selected rating, and whether the status of
the content theme is currently unlocked ( ) or
locked ( ).
Page 33
5. Use the MENU button repeatedly to get back to the Parental Control menu.
6. Select Lock Parental Control from the Parental Control menu for rating limits to take effect,
you must enter the correct password twice. To view age-based ratings after you've locked
them, follow the same steps as above to unlock.
Blocking Specific Content Themes
You can block programs based on their content. (Content is represented by the D, L, S, V and
FV on your screen.) When you block a content theme for a particular rating, you automatically
block that content theme for higher rated programs as well. To block program content:
1. Determine the content themes you want to block.
2. Press the down arrow button to scroll to the rating whose content theme you want to change.
3. Press the right arrow button to move the highlight to a particular content theme.
4. Press the OK button to change its status to block. (For example, you block the language (L)
corresponding with TV-14. The language for TV-MA is blocked as well.)
To view content theme after you've locked them, follow the same steps as above to unlock.
Note:
If you unlock the language corresponding with TV-14, the language for TV-MA doesn't
unlock. You have to unlock the content theme status for each rating separately.
Hierarchy of Age-Based Ratings
TV-MA
TV-14
TV-PG
TV-G
TV-Y7
TV-Y
Mature Audience Only
Parents Strongly Cautioned
Parents Guidance Suggested
General Audience
Directed to Children 7 Years and Older
All Children
Sexually Explicit Dialogue
D
Adult Language
L
Sexual Situations
S
Violence
V
Fantasy Violence
FV
TV Ratings
Go Back
Status D L S V FV
TV-MA View
TV-14 View
TV-PG View
TV-G View
TV-Y7 View
TV-Y View
Press OK to view/block programs with this rating that contain
adult language.
Note:Broadcasters
are not required to
provide content
themes or age-based
ratings.You must
remember to lock
Parental Controls for
rating limits to take
effect.
Note:If you forget your
password, turn off the
TV. Simultaneously
press and hold VOL
DOWN on the side
panel and CANCEL on
the remote for 10
seconds. Next time
you enter the Parental
Control menu, enter a
new password.
US V-Chip Movie Rating Limit
Set movie rating limits by blocking movies rated above a specified level.
To access the Movie Rating Limit menu:
1. Press MENU on the remote control (the TV's Main Menu appears).
2. Select Parental Control.
3. Select US V-Chip.
4. Select Movie Ratings.
5. Press the down arrow button to scroll to the rating you want to change.
6. Press OK to change its status to block (all ratings above the one you selected change to
block).
Using the TV’s FeaturesChapter 3 33
Movie Ratings
Go Back
NR(No Rating) View
X View
NC-17 View
R View
PG-13 View
PG View
G View
Press OK to view/block Movies with this rating.
Page 34
English Ratings
Go Back
18+ View
14+ View
PG View
G View
C8+ View
C View
Press OK to view/block programs with this rating.
Blocking Canada V-Chip Ratings
If you receive Canadian programs you can block Canadian English and French V-Chip by
ratings only. When you block a particular rating, you automatically block the higher rated pro-
grams as well. To block Canadian English and French program ratings:
1. Select Canada V-Chip from the Parental Control menu.
2. Highlight English Ratings or French Ratings and press OK.
3. Determine the rating you want to block.
4. Press the down arrow button to scroll to the rating you want to change.
5. Press OK to change its status to block (all ratings above the one you selected change to
block).
Parental Control
Go Back
Lock Parental Control - - - Select Channel 51 MTV
Block Channel
Block Buttons
US V-Chip
Canada V-Chip
Unrated/Exempt Ratings View
Rating Region Name_12
Press < / > to block/unblock the selected channel.
Parental Control
Go Back
Lock Parental Control - - - Select Channel 51 MTV
Block Channel
Block Buttons
US V-Chip
Canada V-Chip
Unrated/Exempt Ratings View
Rating Region Name_12
Note: You must
remember to lock
parental controls for
rating limits to take
effect.
Block Channel
Turn this option on to block the channel you choose in the Selelct Channel option. Use the
number buttons to enter the channel you want to block, then press the down arrow button.
Press OK to place a check mark in the Block Channel box to block the channel. When you
tune to that channel you'll need to enter a password to view the channel if parental control is
locked.
Block Buttons
Select this option to block (disable) or unblock (enable) the TV’s side panel buttons so that they
can't be used by someone, like a young child. The remote still tunes to any channel. If you're
using this to keep children from changing channels, remove access to any remote that is
capable of operating the television while you have the side panel blocked. Don’t forget to lock
parental controls after you change the status. If you don’t, the Block Buttons action will not
take effect.
Blocking Unrated/Exempt Programs
The Unrated/Exempt Ratings option lets you decide if programs that the V-Chip recognizes as
unrated or exempt can be viewed. Unrated TV programs may include news, sports, political,
religious, local and weather programs, emergency bulletins, public announcements, and pro-
grams without ratings. The Exempt option applies to both USA and Canadian unrated pro-
grams and Canadian programs rated E.
Press the down arrow button to highlight Unrated/Exempt Ratings. Then press the OK or right
arrow button to toggle between View and Block.
View All unrated programs are available
Block All unrated programs are not available.
Future Rating Region
Note:These ratings
are available only if
the broadcaster is
sending them.
You might notice an option in your Parental Control menu that wasn't there before. This is
because broadcasters have the capability to add a new rating system for TV programs.
These ratings let you define additional parameters for parental controls. This option and its
name are dependent on the content acquired from the broadcaster.
34Chapter 3 Using the TV’s Features
Page 35
Additional Features
There are additional features available unrelated to parental controls. These features can be
found in other menus.
Fetch Feature
This is a unique “Fetch” remote control finder function on the HDTV. Pressing the MENU and
VOLUME UP button on the side panel of the TV set at the same time will cause the remote
control to bark from its current location. (only available for models L42FHD38, L46FHD38,
L52FHD38, and L40FHD380)
Screen Formats
Screen format is the way the picture is displayed on your TV. Press the FORMAT button on
your remote to see if a different format is available for the video you are viewing. The format
changes as you press the FORMAT button and the format type is displayed at the bottom of
the screen.
Analog video is sent in a 4/3 format, which your TV displays in a 16/9 format. Most digital
video is sent in a 16/9 format which does fill your screen, but it sometimes is sent in 4/3 which
does not fill your screen. It depends on how the station or device connected to your TV is
formatting the video. If there are bars on the screen, press the FORMAT button to try a different
format that may eliminate the bars. Some bars can't be removed because of the way the
format is sent by the broadcaster.
The different formats available and what they look like follow. Each format is available for
analog video, but it might not be available for digital video.
Normal Zoom
Stretch Cinerama
Using the TV’s Features Chapter 3 35
Page 36
4 Using the TV’s Menu
Using the Menu System
Main Menu
Go Back
Sound
Picture
Channel List
Setup
Parental Control
Time
USB
Sound
Go Back
Equalizer
Sound Type Stereo
Sound Mode Off
Dynamic Bass Off
Balance
Auto Volume Level
Internal Speakers
Advance Settings
This section explores the menus of your TV. Each menu is outlined and detailed to help you
get the most from your TV. The Parental Control menu is discussed in Chapter 3. To access the
menu system:
1. Press the MENU button.
2. Use the up and down arrow buttons to highlight an option and press OK to display it.
The name of the menu is displayed at the top of the menu screen.
3. Press the up and down arrow buttons to move to a different option within the menu. If
necessary, press the OK button to display the choices of the option you’ve highlighted.
If available, use the text at the bottom of each screen for help.
4. To return to the Main Menu, press the MENU button until it's displayed.
Descriptions of each menu are discussed in the order they appear.
There are two ways to exit a menu:
•
Press the CANCEL button. The menus are cleared from the screen and you return to TV
viewing.
•
Press the MENU button repeatedly until the menus disappear.
Sound Menu
The Sound menu lets you adjust audio output. To access the Sound menu, press MENU on
the remote, and then select Sound from the Main Menu. The following audio items can be
adjusted:
Equalizer The five-band graphic equalizer lets you adjust the audio frequency settings. You
can select one of the five-band Equalizer Presets or create your own personal preset.
Sound Preset Allows you to choose a specific Sound Preset. Press the right arrow to cycle
through the options: Standard, Movie, Voice, Music and Personal.Frequency Range Displays the different graphic equalizer bands set for each Sound
Preset option. Choose a band and make adjustments. When you make adjustments, the
Sound Preset option automatically changes to Personal. Press the left or right arrow button
to select the frequency (100Hz, 300Hz, 1KHz, 3KHz, 10KHz) you want to adjust. Then use
the up or down arrow button to adjust the level. When you're done adjusting the levels, press
the MENU button to exit.
To view the frequency range of another Sound Preset option, press the right or left arrow
until no band is selected and Frequency Range is highlighted. Then press the up arrow to
highlight Sound Preset.
Sound Type Controls the way the sound comes through your speakers. The options available vary according to the input selected.
Mono (available for regular TV viewing only) Plays the sound in mono only. Use this setting
when receiving broadcasts with weak stereo signals.
Stereo Splits the incoming stereo audio signal into left and right channels. Most TV
programs and recorded materials have stereo audio. The word Stereo appears in the channel banner when you tune to a program that is broadcast in stereo.
36Chapter 4 Using the TV’s Menu
Page 37
Sound Mode Provides special processing through your speakers (depending on the setting
you chose as your Sound Type). The available sound modes are:
Off Does not give any special sound processing.
SRS WOW Gives a surround effect with more bass. (available for models L42FHD37,
L46FHD37, and L46FHD35)
SRS TurSurround XT (available for models L42FHD38, L46FHD38, L52FHD38, and
L40FHD380)
Dynamic Bass Improves bass output. Displays a choice list of available settings you can
adjust: Off and On.
Balance Press the right or left arrow buttons to adjust how much audio is sent to the left and
right speakers.
Auto Volume Level Reduces the annoying blasts in volume during commercial breaks, and
also amplifies softer sounds in program material. Eliminates the need to constantly adjust the
volume.
Internal Speakers Turn on or off the internal speakers. If you have a device connected to the
AUDIO OUTPUT jacks on the back of the TV and you want to control the sound by the device
instead, uncheck the box.
Advanced Settings
Second Audio Program (SAP) Plays the program’s audio in a second language, if one is
available. The letters SAP appear in the channel banner when you tune to a program that is
broadcast with SAP information. SAP audio is broadcast in mono. SAP is also used to
broadcast a program’s audio with descriptions of the video for the visually impaired.
Default Audio Language Choose the language you prefer for dialog on digital channels.
If your preferred language is being broadcast with a program, then the TV plays it. If not,
then the TV plays the default audio for the program (usually English in the U.S.). The default
digital channel audio language options are English, Spanish, French, German, and Italian.
Advanced Settings
Go Back
SAP
Default Audio language English
Current Audio Track
Current Audio Track (not available for analog channels)
Press the right arrow to
choose from the audio languages available for the program you're watching. The lan-
guage you choose becomes your preferred audio language for all digital channels until
you turn the TV off. If the language you choose here is not being broadcast with a
program, then the TV plays the default audio for the program (usually English in the U.S.).
Note: This menu will gray-out when current channel selected is analog.
Using the TV’s Menu Chapter 4 37
Page 38
Picture
Go Back
Picrure Preset Vibrant
Brightness
Contrast
Color
Sharpness
Tint
Color Warmth Normal
Video Noise Reduction Low
Note:Video
noise reduction is
available for the
CMP1 and CMP2
inputs only if the
signal is 480i.
Picture Menu
The Picture menu contains menus and controls to configure how the picture looks. The
Picture menu options apply to the video for the main TV and VIDEO INPUT selections. All
picture options can be applied to each input - VID1, VID2, CMP1 or CMP2, HDMI1, HDMI2or HDMI3, and PC.
Picture Preset (not available on PC) Displays a choice list that lets you select one of the
preset picture settings: Vibrant, Sports, Personal, Natural, or Cinematic. Choose the setting
that is best for your viewing environment.
Brightness Use the left or right arrow buttons to adjust the brightness of the picture.
Contrast Use the left or right arrow buttons to adjust the difference between the light and dark
areas of the picture.
Color Use the right or left arrow buttons to adjust the richness of the color.
Sharpness (not available on PC) Use the right or left arrow buttons to adjust the crispness
of the edges in the picture.
Tint (not available on PC) Adjusts the balance between the red and green levels.
Color Warmth Displays a choice list that lets you set one of three automatic color adjustments:
Cool for a more blue palette of picture colors; Normal; or Warm for a more red palette of
picture colors. The warm setting corresponds to the NTSC standard of 6500 K. When you
change any of these picture settings, the Picture Preset changes to Personal. Use the left or
right arrow button to make adjustments.
Video Noise Reduction (not available on PC) Reduces picture “static” or any type of
interference. This feature is especially useful for providing a clearer picture in weak analog
signal conditions. Press the right arrow to choose between: Off for no noise reduction; Low for
a softer, smoother picture that retains picture sharpness and detail; Medium for a slightly softer
picture than the Low setting; High for an even softer, smoother picture than the other settings
(the picture detail is somewhat decreased).
Channel List Menu
The Channel List menu allows you to view all the channels available in your channel list. Press
the up or down arrow button to highlight a channel then press OK to tune to the channel.
Setup
Go Back
Channel Setup
List and Lables
Autotuning
Closed Caption
Prefereces
Dynamic Backlight Off
Light Sensor Off
HDMI CEC Off
38Chapter 4 Using the TV’s Menu
Setup Menu
The Setup menu lets you configure the TV to fit its surroundings and your preferences. To
access the Setup menu, press MENU on the remote, and then select Setup from the Main
Menu.
Channel Setup
Signal Type Choose the type of signal you have connected to the ANTENNA/CABLE INPUT.
Channel Search Searches for channels the signal is receiving. Go to page 17 for more
information.
List and Labels
Edit the channels in the list or choose labels for each video input channel.
Channel Number Use the number buttons on your remote to enter the channel number,
or press left and right arrow buttons to select the VIDEO INPUT channel among VID1,VID2, CMP1, CMP2, PC, HDMI1, HDMI2 and HDMI3.
Page 39
In Channel List (only available for TV channels) If you've entered a channel you want to
add to the channel list, highlight In Channel List and press the right arrow to place a check
in the check box. If you've entered a channel you want to delete from the channel list, press
the right arrow button to uncheck the box. When an AV INPUT is displayed in the Channel
number field, the line “In channel list” is grayed-out.
Channel Label (not available for TV channels)
Allows you to select a label for the video
input channel selected in Channel Number. The label is displayed on the screen when you
tune to this input channel. When a channel number is displayed in the Channel Number
field, this is grayed-out.
Autotuning Go to Chapter 3 for details about the Autotuning feature.
Closed Caption
Many programs are encoded with closed-captioning information, which lets you display the
audio portion of a program as text on the TV screen.
Note: Closed caption settings are not available for HDMI1, HDMI2, HDMI3, CMP1, or CMP2
INPUTS. These settings must be set in the connected device's menu. Closed captioning is not
available on all channels at all times. Only specific programs are encoded with closed-captioning
information. When a program is closed captioned, CC is displayed in the channel banner. See
Chapter 3 for more information about the channel banner. The closed caption options are:
CC Setting Lets you choose the way closed captioning information appears on the
screen.
OffNo captioning information displayed.
On always
On when muted
Captioning information shown always, when available.
Displays captioning information, when available, whenever the TV’s
sound is muted by pressing the MUTE button. The captioning information is not
displayed when the sound is not muted.
Analog CC Type If available, lets you select the captioning mode used for displaying
captioning information. If you are unsure of the differences among the modes, you may
prefer to leave the closed captioned mode set to CC1, which displays complete text of the
program in the primary language in your area.
Digital CC Type If available, lets you select a closed caption service mode (1.6) for digital
channels.
Digital CC Preset If available, lets you select between Default and Custom options.
Custom changes according to what you set for the options below.
Digital CC Style If available, lets you customize the following display options:
Digital CC Size Lets you set the size of the digital closed-caption text. You can choose
Standard, Large, or Small.
Digital CC Font Lets you select a character design for the digital closed-caption text.
A font is a complete assortment of letters, numbers, punctuation marks, etc. in a given
design. You can choose from a variety of fonts (Semi Serif, Screen Serif, etc.).
Digital CC Opacity Lets you set the appearance of the digital closed-caption text:
Solid, Transparent, Translucent, or Flashing.
Digital CC Color Lets you choose the color of the digital closed-caption text: White,
Red, Green, Blue, Yellow, Magenta, Cyan or Black.
Digital CC Back. Opacity Lets you set the appearance of the space behind the digital
closed-caption text: Solid, Transparent, Translucent, or Flashing.Digital CC Back. Color Lets you choose the color of the area of the screen behind the
digital closed-caption text: White, Red, Green, Blue, Yellow, Magenta, Cyan or Black.
List and Labels
Go Back
Channel Number 10
In Channel List
Channel Label
Press < / > to add/remove this channel to/from the list.
Closed Caption
Go Back
CC Setting Off
Analog CC Type CC1
Digital CC Type Service1
Digital CC Preset Default
Digital CC Style
Digital CC Style
Go Back
Digital CC Size Small
Digital CC Font Semi Serif
Digital CC Opacity Solid
Digital CC Color White
Digital CC Back. Opacity Solid
Digital CC Back. Color Black
Using the TV’s Menu Chapter 4 39
Page 40
Preferences
Go Back
Channel Number Display
Language English
Power Save Mode
To always display the channel number on screen, put check in
the box using the OK key.
TV mode
Backlight
Power Level
Standby
Off
On
Full Power Level
On
Mid Power Level
On
Low Power Level Green
LED Color
Off
Blue
Cyan
Note: The
connected HDMI
device must be
HDMI CEC compliant
in order for this
feature to work.
However, some
HDMI devices may
utilize specific
protocols that are not
fully CEC compliant
and may prevent the
feature from working
properly.
Note: These captioning style options only have an effect on true digital closed captions.
Not all captioning on digital channels is digital captioning--it depends on what the broadcaster is
sending. If the closed captioning for a program is not digital, the Digital CC style settings will not
have an effect.
Preferences
Channel Number Display Tu rn this feature on if you want the channel number always visible.
Language Lets you select your preferred language for the menus: English, Espanol or Francais.
Power Save Mode If no signal is detected from the Input/RF INPUT for 5min, the TV set
goes to standby mode.
Dynamic Backlight Option: On/Off. If you choose On, the TV will continually monitor the
video content being displayed and will adjust the backlight to achieve optimum contrast levels.
Light Sensor If you choose On, this feature is activated.
• When activated, this feature monitors the ambient light conditions in the room and adjusts
the TV’s backlight for optimum viewing. It also serves as an energy saving feature by lowering
the backlight power level when appropriate (typically in darker room conditions).
• The TV has a multi-colored LED that adjusts based on the backlight power level with “green”
representing the highest level of energy savings. Please refer to the table at the left for the various
conditions of the backlight power level and LED colors when the light sensor is active.
Note: When TV is On and the light sensor is Off, the LED color will be blue.
HDMI CEC (Consumer Electronics Control)
If choose On, the HDMI CEC function is enabled. This feature provides expanded capabilities
when your TV is connected to an HDMI CEC compliant device using a certified HDMI 1.3 cable.
Here is an example using an HDMI CEC compliant DVD player connected to the TV.
• Upon activating the feature, the TV searches for HDMI CEC compliant devices that are
connected. In this example, a connected DVD player is found.
• When both the TV and DVD player are On and you insert a disc into the DVD player, the
TV will automatically switch to the associated input and initiate play.
• When the TV is on and the DVD player is turned on with the disc already loaded, the TV
will automatically switch to the associated input and initiate play.
• If you connect another HDMI CEC device and /or change the HDMI input used for an
existing HDMI CEC device, you should turn the HDMI CEC function Off and then turn it
back On again in order for the TV to complete a new search for the connected devices.
Time
Go Back
Sleep Timer 03:00 Z
Auto Time Channel 12 PBS
Time Zone Eastern
Daylight Saving Automatic
Enter time 8:25PM
Wake up Timer Daily
Wake up Time 8:00AM
Tur n off Timer Once
Turn off Time 10:00PM
Parental Control Menu
The Parental Control menu is explained in Chapter 3. Go to page 31 for more information.
Time Menu
Sleep Timer Use the left and right arrow keys to set the TV to turn off after a given amount of time.
Auto Time Channel Choose a station to have the TV set the time for you. Wait about one
minute for the time to be set.
Time Zone Select the current local time among Atlantic, Newfoundland, Central, Mountain,
Pacific, Alaska, Hawaii and Eastern.
Daylight Saving (DST) Choose between Off and Automatic modes.
ZZ
Enter Time If you didn't set the time reference channel, enter the current time manually. If
it is 8:00, for example, you must first enter the number zero, then number eight. Use the OK
button to choose between AM and PM.
Wake up Timer Use the left and right arrow keys to choose between Off, Once or Daily to set
the TV to turn itself on just one time or at the same time each day.
Note: The Wake up Timer is available only when the time has been set.
Wake up Time Set the time you want the TV to turn itself on. To enter 8:00, for example, you
must first enter the number zero, then number eight. Use the OK button to choose between AM
and PM.
Turn off Timer Use the left and right arrow keys to choose between Off, Once, or Daily to set
the TV to turn itself off just one time or at the same time daily.
Turn off Time Set the time you want the TV to turn itself off. To enter 8:00, for example, you
must first enter the number zero, then number eight. Use the OK button to choose between AM
and PM.
40Chapter 4 Using the TV’s Menu
Page 41
USB Menu
The USB feature allows to play audio files (format supported: MP3) or display pictures (format
supported: JEPG)
Select USB in the Main Menu, then select USB Device.
USB Device
Picture If you have pictures on your USB device connected to your TV, this menu allows
you to view the pictures individually by pressing the up/down arrow buttons to highlight the
picture (the picture is displayed on the right).
Note: To play a slideshow of all the pictures available on your device, highlight a folder and press
PLAY.
Music If you have mp3 audio files on your USB device connected to your TV, this menu
allows you to play files individually by pressing the up/down arrow buttons to highlight the
song.
Note: To play a slideshow of all the music files available on your device, highlight a folder and
press PLAY.
USB Connection
Main Menu
Go Back
Sound
Picture
Channel List
Setup
Parental Control
Time
USB
Connecting a device with USB or a USB flash drive
This connection allows you to insert a USB flash drive directly or connect to a compatible
mass storage device with USB, such as a digital camera, multi-format card reader, or mp3
player.
If you have a USB flash drive, plug in the drive directly.
If you have a device with USB:
• Connect one end of the USB cable to the USB device and the other end to the USB jack
on the side of TV.
• To access and adjust the options of the USB device, press MENU then choose USB from
the Main Menu.
Using the TV’s Menu Chapter 4 41
Note: When using a
USB connection, a
picture slideshow
can be set for a
folder not per picture
Page 42
5 Other Information
Frequently Asked Questions (FAQs)
What’s the quickest way to view High Definition (HD) video?
Connect an off-air antenna to the ANTENNA/CABLE Input to view free local digital channels.
You might need to purchase an antenna. Go to page 10 for more information.
Visit www.antennaweb.org for help deciding what type of antenna to use to receive the local
digital channels available to you. By entering where you live, this mapping program tells you
which local analog and digital stations are available using a certain antenna.
Are there other ways to view High Definition (HD) video?
Besides using an off-air antenna as mentioned above, you can also use a set-top box to receive
digital video. Contact your cable company or satellite provider to purchase digital programming
and have them connect the box for you to ensure you're viewing channels the best way.
How do I tell an analog channel from a digital channel?
Press the INFO button to display the channel banner. Look at the bottom left corner of the
screen. An A is displayed for an analog channel. A D is displayed for a digital channel.
Why are there bars on my screen and can I get rid of them?
Most digital video is sent in a 16/9 format which does fill your screen, but is sometimes sent in
4/3 which does not fill your screen. It depends on how the station or device connected to your
TV is formatting the video. If there are bars on the screen, press the FORMAT button to try a
different format that may eliminate the bars. Some bars can't be removed because of the way the
format is sent by the broadcaster. The format changes as you press the FORMAT button and the
format type is displayed at the bottom of the screen. For more information on screen formats, go
to page 35.
Why does channel search find a lot of channels, but when I try to tune to
them there’s nothing there?
Some channels enabled by the cable company don’t carry programming, such as video on-
demand. When channels are unavailable, your TV’s screen is blank or appears like snow. You
probably want to remove these channels from your channel list. Remove these in the Channel
List menu. Go to page 38 for more information.
Why does the first channel search take a long time?
If you have both analog and digital channels, the TV is looking for all available channels in the
channel list. If you do have digital channels, the TV is also searching for scrambled channels,
non-scrambled channels, and each sub-channel of that digital channel.
42Chapter 5 Other Information
Page 43
Troubleshooting
Most problems you encounter with your TV can be corrected by consulting the following troubleshooting list.
TV Problems
TV won’t turn on
•
Make sure the TV is plugged in.
•
Check the wall receptacle (or extension cord) to make sure it is “live” by plugging in something else.
•
The side panel controls may be locked (disabled). Use the remote control to unlock the side panel controls
by selecting the Block Buttons feature on the Parental Control menu and press OK to uncheck the box.
No picture and no sound but TV is on
•
You might be tuned to an input with no device connected to it to view. If you're trying to view a connected
device, press INPUT until the picture from that device appears.
•
The Signal Type option may be set incorrectly. Go to page 17 for detailed instructions.
•
The channel might be blank--change channels.
•
If you’re watching your VCR and it’s connected with coaxial cable to the ANTENNA/CABLE jack, tune the
TV to channel 3 or 4 (whichever channel is selected on the 3/4 switch on the back of your VCR). Also make
sure the TV/VCR button on the VCR is in the correct mode (press the TV/VCR button on your VCR).
Sound okay, picture poor
•
If you're getting a black and white picture from a device you've connected to your TV, you might have your
video cables connected to the wrong jacks. A yellow Video cable connects to the yellow VIDEO INPUT jack
on the side or back of your TV; three video cables or bundled component video cables (red, blue, and green)
connect to the corresponding COMPONENT INPUT jacks on the back of your TV.
•
If you're getting no picture from a device you've connected to your TV, you might have your video cable
connected to the VIDEO OUTPUT jack on the back of your TV. These jacks are used to connect recording
devices. A yellow Video cable connects to the yellow VIDEO INPUT jack on the side or back of your TV.
•
Check antenna connections. Make sure all of the cables are firmly connected to the jacks.
•
Try adjusting the sharpness function to improve weak signals. Go to page 38 for more instructions.
No sound, picture okay
•
The sound might be muted. Try pressing the volume up button to restore sound.
•
If using DVI, S-Video, or Y, PB, PR, remember to also connect the device’s left and right AUDIO OUTPUT
jacks to the TV’s L and R AUDIO INPUT jacks.
•
The sound settings may not be set correctly. Go to page 36 for more information.
•
The internal speakers might be turned off. Go to page 37 for more information.
•
If your audio source has only one jack or is a (mono) audio source, make sure you have plugged the
connection into the Left AUDIO INPUT jack on the TV.
Blank screen
•
Check your connections. If you used yellow, red, and white cables to connect, make sure they're connected
to the yellow, red, and white VIDEO INPUT jacks on the side or back of the TV, not to the VIDEO OUTPUT
jacks on the back of the TV.
•
If you're trying to watch something that's playing on a device connected to the TV (like a DVD), press
INPUT until you get to the correct video input channel.
•
Make sure the device connected to the TV is turned on.
•
Try another channel.
Other Information Chapter 5 43
Page 44
Buttons don’t work
•
The side panel controls may be locked (disabled). Use the remote control to unlock the side panel controls by
selecting the Block Buttons feature in the Parental Control menu and press OK to uncheck the box.
•
Unplug the TV for ten minutes and then plug it back in. Turn the TV on and try again.
TV turns off unexpectedly
•
Sleep timer may have been activated. Go to page 40 for instructions.
•
Electronic protection circuit may have been activated because of a power surge. Wait 30 seconds and then
turn on again. If this happens frequently, the voltage in your house may be abnormally high or low.
•
Unplug. Wait ten minutes. Plug in again.
TV turns on unexpectedly
Wake up timer might have been activated. Go to page 40 for instructions.
Can’t select certain channel
•
Channel may be blocked or not approved in the Parental Control menu.
•
If using a VCR, check to make sure the TV/VCR button on the VCR is in the correct mode (press the TV/VCR
button on your VCR).
•
Press the TV button and then try to change channels.
Noisy stereo reception
May be a weak station. Use the Sound menu and Sound Type to choose mono.
Black box appears on the screen
Closed-captioning might be on. Check Closed Caption in the Setup menu. Go to page 39 for more instructions.
Problems with HDMI Connection
•
Make sure the HDMI or DVI device is turned on and the cables are firmly connected. If problems still occur,
turn off your device. Re-connect your device. Reset the power by unplugging the power cord and plugging
it back in.
•
If you are tuned to the HDMI 1, HDMI 2 or HDMI 3 INPUT and you’re receiving Unusable Signal message
onscreen, press the INFO button on the remote. If Acquiring Channel appears in the channel banner, the
HDMI or DVI device isn’t responding. Contact the manufacturer of the HDMI or DVI device for further assistance.
•
If you tune to the HDMI 1, HDMI 2 or HDMI 3 INPUT and you see snow, the video goes in and out, or the video
takes a long time to appear, your HDMI or DVI device is having trouble sending video information to the TV.
Re-connect your device. Reset the power by unplugging the power cord and plugging it back in. If problems
persist, try connecting the Y Pb Pr jacks if they are available or contact the manufacturer of the HDMI or DVI
device for further assistance.
•
If you have black bars on each side of your picture, the device you connected might have a switch or a
menu option allowing you to change the picture quality output that will fix this. Choose either 720p or
1080i.
•
480i signals aren’t supported by the HDMI2/DVI, HDMI1 or HDMI3 INPUT.
The Remote Control Doesn’t Work
•
Something might be between the remote and the remote light sensor on the front of the TV. Make sure
there is a clear path.
•
The remote may not be aimed directly at the TV.
•
The batteries in the remote may be weak, dead, or installed incorrectly. Put new batteries in the remote. (Note,
if you remove the batteries, you may have to reprogram the remote to operate other devices.)
44Chapter 5 Other Information
Page 45
Problems with V-Chip/Parental Controls
The rating limits don’t work
You must lock the settings. Go to the Main Menu (press MENU on your remote), select Parental Control,
select Lock Parental Control.
I don’t remember my password and I want to unlock the TV
If you forget your password, turn the TV off. Simultaneously press and hold VOL DOWN on the side panel and
CANCEL on the remote for 10 seconds. Next time you enter the Parental Control menu, enter a new password.
The V-Chip won’t let me watch a program even though it’s not rated as violent.
Maybe the movie was given an NR (Not Rated) status. After you block movie ratings, you must set NR to
View Separately in order to view movies with an NR rating.
What Else Can I Do?
If you’ve been through the Troubleshooting section and nothing has fixed your problem, try rebooting your
TV. Note that after a reboot you may need to run your TV through the setup process again. To do a reboot,
unplug the power cord from the wall outlet, power strip, etc. Keep your TV unplugged for about 5 minutes.
Then plug in the TV, turn on the TV, and see if the problem is fixed. If the problem remains, then please click
on the Customer Support Menu at www.rca.com/television for updated FAQs or contact RCA Customer
Support at the support number provided in your Warranty under How To Get Service.
Other Information Chapter 5 45
Page 46
V-Chip Rating Explanations
US V-Chip Rating System
TV-MA (Mature Audience Only) Specifically designed to be viewed by adults and may be unsuitable for
children under 17. It contains one or more of the following content themes: crude indecent language (L),
explicit sexual activity (S), or graphic violence (V).
TV-14 (Parents Strongly Cautioned) Contains some material that many parents would find unsuitable for
children under 14. Parents are strongly urged to exercise greater care in monitoring this program and are
cautioned against letting children under the age of 14 watch unattended. This program contains one or more
of the following content themes: intensely suggestive dialogue (D), strong coarse language (L), intense sexual
situations (S), or intense violence (V).
TV-PG (Par ental Guidance Suggested) Contains material that parents may find unsuitable for younger children.
Many parents may want to watch it with their younger children. The program contains one or more of the
following content themes: some suggestive dialogue (D), infrequent coarse language (L), some sexual situa-
tions (S), or moderate violence (V).
TV-G (Parental Audience) Most parents would find this program suitable for all ages. It contains little or no
sexual dialogue (D) or situations (S), no strong language (L), and little or no violence (V).
TV-Y7 (Directed to Children 7 years and older) Designed for children ages 7 and above. It may be more
appropriate for children who have acquired the developmental skills needed to distinguish between make be-
lieve and reality. Themes and elements in this program may include mild fantasy violence (FV) or comedic violence,
or may frighten children under the age of 7.
TV-Y (All Childr en) Themes and elements in this program are designed for a young audience, including children
ages 2-6. It is not expected to frighten younger children.
Canadian English V-Chip Rating System
18+ (Adult) Programming intended for adults 18 and older. It may contain elements of violence, language, and
sexual content which could make it unsuitable for viewers under 18. Violence Guidelines: May contain violence
integral to the development of the plot, character or theme, intended for adult audiences. Other Content
Guidelines: May contain graphic language and explicit portrayals of nudity and/or sex.
14+ (Viewer 14 and over) Programming contains themes or content which may not be suitable for viewers
under the age of 14. Parents are strongly cautioned to exercise discretion in permitting viewing by pre-teens
and early teens. Violence Guidelines: May contain intense scenes of violence. Could deal with mature
themes and societal issues in a realistic fashion. Other Content Guidelines: May contain scenes of nudity
and/or sexual activity. There could be frequent use of profanity.
PG (Parental Guidance) Programming intended for a general audience but which may not be suitable for
younger children (under the age of 8). Parents may consider some content inappropriate for unsupervised
viewing by children aged 8-13. Violence Guidelines: Depictions of conflict and/or aggression will be limited and
moderate; may include physical, fantasy, or supernatural violence. Other Content Guidelines: May contain
infrequent mild profanity, or mildly suggestive language. Could also contain brief scenes of nudity.
46Chapter 5 Other Information
Page 47
G (General Audience) Programming considered acceptable for all ages groups. While not designed specifi-
cally for children, it is understood younger viewers may be part of the audience. Violence Guidelines: Will
contain very little violence, either physical or verbal or emotional. Will be sensitive to themes which could
frighten a younger child, will not depict realistic scenes of violence which minimize or gloss over the effects of
violent acts. Other Content Guidelines: There may be some inoffensive slang, no profanity and no nudity.
C8+ (Children 8 and older) Programming generally considered acceptable for children 8 years and over to
watch on their own. Violence Guidelines: Violence will not be portrayed as the preferred, acceptable, or only way
to resolve conflict or encourage children to imitate dangerous acts which they may see on television. Any realistic
depictions of violence will be infrequent, discreet, of low intensity and will show the consequences of the acts.
Other Content Guidelines: There will be no profanity, nudity or sexual content.
C (Children) Programming intended for children under age 8. Violence Guidelines: Careful attention is paid to
themes which could threaten children’s sense of security and well being. There will be no realistic scenes of
violence. Depictions of aggressive behavior will be infrequent and limited to portrayals that are clearly imaginary,
comedic or unrealistic in nature. Other Content Guidelines: There will be no offensive language, nudity or sexual
content.
Canadian French V-Chip Rating System
18+ (Adult) Programming is for adults only. This program contains sustained violence or extremely violent
scenes.
16+ (Viewer 16 and over) Programming is not suitable for those under age 16. This program contains frequent
scenes of violence or intensely violent scenes.
13+ (Viewer 13 and over) Programming may not be suitable for children under the age of 13. This program
either contains several violent scenes or one or more scenes that are violent enough to affect them. Viewing in
the company of an adult is therefore strongly recommended for children under the age of 13.
8+ (Viewer 8 and over) Not recommended for young children. This program is suitable for most audiences,
but it contains mild or occasional violence that could upset young children. Viewing in the company of an adult
is therefore recommended for young children (under the age of 8) who do not distinguish between reality and
imagination.
G (General Audience) This program is suitable for audiences of all ages. It contains no violence, or any
violence that it does contain is either minimal or is presented in a humorous manner, as a caricature, or in an
unrealistic way.
Other Information Chapter 5 47
Page 48
TTE Technology, Inc. (“TTE”) Limited Warranty
All LCD Models
EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW, THIS WARRANTY
DOES NOT COVER, AND AS DESCRIBED BELOW TTE EXPRESSLY DISCLAIMS, ALL
ACTUAL AND IMPLIED WARRANTIES WITH RESPECT TO ANY PRODUCT USED FOR
INSTITUTIONAL OR OTHER COMMERCIAL PURPOSES (INCLUDING BUT NOT
LIMITED TO RENTAL PURPOSES).
What your warranty covers:
Defects in materials or workmanship to the original owner
New LCD Televisions - screen sizes 32” and smaller:
•
For how long after your purchase:
•
Ninety (90) days from date of purchase for labor charges. After ninety (90) days, labor charges will be at
owner expense.
•
One (1) year from date of purchase for parts.
•
What we will do:
•
At TTE’s discretion, pay an Authorized RCA Service Center for both labor charges and parts to repair
your television, or replace your television with a new or refurbished/remanufactured unit.
get service”
See “How to
New LCD Televisions - screen sizes 33” and larger:
•
For how long after your purchase:
•
One (1) year from the date of purchase for labor charges.
•
One (1) year from the date of purchase for parts.
•
What we will do:
•
At TTE’s discretion, pay an Authorized RCA Service Center for labor charges and parts to repair your
television, or replace your television with a new or refurbished/remanufactured unit. See “How to
get service”
All Remanufactured/Refurbished LCD Televisions:
•
For how long after your purchase:
•
Ninety (90) days from date of purchase for labor charges.
•
Ninety (90) days from date of purchase for parts.
•
What we will do:
•
At TTE’s discretion, pay an Authorized RCA Service Center for both labor charges and parts to repair
your television, or replace your television with a refurbished/remanufactured unit. See “How to
get service”
How to get service:
•
Call 1-800-951-9582. Please have your unit’s date of purchase and model/serial number ready. The model/
serial number information can be found on the back of your unit.
•
A representative will troubleshoot your problem over the phone.
•
If it is determined that your unit requires service, the service location will be at the sole discretion of TTE
based upon the TTE Limited Warranty statement.
•
At the sole discretion of TTE, television screen sizes 32” and smaller is either consumer carry-in to an
Authorized RCA Service Center or directly exchanged for a new or refurbished/remanufactured unit.
•
At the sole discretion of TTE, television screen sizes 33” and larger is either consumer carry-in to an
Authorized RCA Service Center or directly exchanged for a new or refurbished/remanufacture unit.
•
Proof of purchase in the form of a bill of sale or receipted invoice from an Authorized Dealer which is
evidence that the product is within the warranty period must be presented to obtain warranty service.
What your warranty does not cover:
•
Customer instruction. (Your Owner’s Manual describes how to install, adjust, and operate your unit. Any
additional information should be obtained from your dealer.)
•
Installation and related adjustments.
48Chapter 5 Other Information
Page 49
•
Damage resulting from non-approved installation methods.
•
Signal reception problems not caused by your unit.
•
Damage from misuse or neglect.
•
Batteries.
•
A television that has been modified or incorporated into other products or is used for institutional or other
commercial purposes (including but not limited to rental purposes).
•
A unit purchased or serviced outside the U.S.A.
•
Acts of nature, such as but not limited to lightning damage.
•
Special, incidental or consequential damages.
Product Registration:
Please complete and mail the Product Registration Card packed with your unit or register on-line at
www.rca.com/television. It will make it easier to contact you should it ever be necessary. The return of the
card is not required for warranty coverage.
Limitation of Warranty:
•
THE WARRANTY STATED ABOVE IS THE ONLY WARRANTY APPLICABLE TO THIS
PRODUCT. NO VERBAL OR WRITTEN INFORMATION GIVEN BY TTE
TECHNOLOGY, INC., ITS AGENTS OR EMPLOYEES SHALL CREATE A GUARANTY
OR IN ANY WAY INCREASE OR MODIFY THE SCOPE OF THIS WARRANTY.
•
REPAIR OR REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS THE
EXCLUSIVE REMEDY OF THE CONSUMER. TTE TECHNOLOGY, INC. SHALL NOT
BE LIABLE FOR SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING
FROM THE USE OF THIS PRODUCT OR ARISING OUT OF ANY BREACH OF ANY
EXPRESS OR IMPLIED WARRANTY ON THIS PRODUCT. THIS DISCLAIMER OF
WARRANTIES AND LIMITED WARRANTY ARE GOVERNED BY THE LAWS OF THE
STATE OF INDIANA. EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW,
ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR
PURPOSE ON THIS PRODUCT IS LIMITED TO THE APPLICABLE WARRANTY AND
WARRANTY PERIOD SET FORTH ABOVE.
How State Law relates to this warranty:
•
Some states do not allow the exclusion nor limitation of incidental or consequential damages, or limitations
on how long an implied warranty lasts, so the above limitations or exclusions may not apply to you.
•
This warranty gives you specific legal rights, and you also may have other rights that vary from state to state.
If you purchased your unit outside the United States or seek warranty coverage
outside the United States:
This warranty does not apply. Contact your dealer for warranty information.
Service calls which do not involve defective materials or workmanship are not covered
by this warranty. Costs of such service calls are the sole responsibility of the purchaser.
EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW, THIS WARRANTY
DOES NOT COVER, AND AS DESCRIBED BELOW TTE EXPRESSLY DISCLAIMS,
ALL ACTUAL AND IMPLIED WARRANTIES AND CONDITIONS WITH RESPECT TO
ANY PRODUCT USED FOR INSTITUTIONAL OR OTHER COMMERCIAL PURPOSES
(INCLUDING BUT NOT LIMITED TO RENTAL PURPOSES).
What your warranty covers:
Defects in materials or workmanship to the original purchaser.
For how long after purchase:
•
All RCA televisions: One year parts and labor.
•
All RCA Scenium televisions: Two years parts and labor.
What TTE Technology Canada Ltd. will do:
•
At TTE’s discretion, pay an Authorized RCA Service Centre for both labor charges and parts to repair your
television, or replace your television with a new or refurbished/remanufactured unit.
service”
See “How to get
How to get service:
•
Call 1-866-465-7157 (French: 1-800-522-0445). Please have your unit’s date of purchase and model/
serial number ready. The model/serial number information can be found on the back of your unit.
•
A representative will troubleshoot your problem over the phone.
•
If it is determined that your unit requires service, the service location will be at the sole discretion of TTE
based upon the TTE Limited Warranty statement.
•
At the sole discretion of TTE, RCA CRT DV televisions are either consumer carry-in to an Authorized RCA
Service Centre or directly exchanged for a new or refurbished/remanufactured unit.
•
At the sole discretion of TTE, RCA LCD televisions are either consumer carry-in to an Authorized RCA
Service Centre, directly exchanged for a new or refurbished/remanufacture unit or provided in-home service.
•
At the sole discretion of TTE, RCA Scenium LCD televisions are either consumer carry-in to an Authorized
RCA Service Centre, directly exchanged for a new or refurbished/remanufacture unit or provided in-home
service.
•
Proof of purchase in the form of an original bill of sale or receipted invoice from an Authorized Dealer which
is evidence that the product is within the warranty period must be presented to obtain warranty service.
Your warranty does not cover damages which are caused by:
•
Fire, accident, lightening, flood and/or other acts of God;
•
Faulty installation, set-up adjustments, improper antenna, inadequate signal reception, adjustment of
You can clean the TV as required, using a soft lint-free cloth. Be sure to occasionally dust the ventilation slots
in the cabinet to help assure adequate ventilation.
IMPORTANT: Never use strong cleaning agents, such as ammonia-based cleaners, or
abrasive powder. These types of cleaners will damage the TV. The TV’s screen may be
cleaned with a soft, lint-free cloth as well. Take care not to scratch or mar the screen.
If necessary, you may use a cloth dampened with warm water. While cleaning do not
spray liquid directly on the screen, or allow liquid to run down the screen and inside the
TV. Also, never place drinks or vases with water on top of the TV.
the risk of fire, shock hazard or damage to the TV.
This could increase
Other Information Chapter 5 51
Page 52
ENERGY STAR is a set of power-saving guidelines issued by the U.S. Environmental Protection Agency (EPA).
Manufactured under license from Dolby Laboratories.
“Dolby” and the double-D symbol are registered trademarks of Dolby Laboratories.
WOW, SRS and symbol are trademarks of SRS Labs, Inc. WOW technology is incorporated under
license from SRS Labs, Inc.
TruSurround XT, SRS and symbol are trademarks of SRS Labs, Inc. TruSurround XT technology is
incorporated under license from SRS Labs, Inc.
FCC Information
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used
in accordance with the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged
to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
This Class B digital apparatus complies with Canadian ICES-003.
Visit the RCA website at www.rca.com/television
Please do not send any products to the Indianapolis address listed in this manual or on the carton. This will only
add delays in service for your product.