This symbol indicates "dangerous
voltage" inside the product that
presents a risk of electric shock or
personal injury.
WARNING
To reduce the risk of fi re or electric shock, do not
expose this product to rain or moisture. The apparatus
shall not be exposed to dripping or splashing. No objects fi lled with liquids, such as vases, shall be placed
on the apparatus.
This symbol indicates that this product contains mercury. Special disposal of this product for environmental
reasons may be required under the laws applicable to your jurisdiction. For disposal or recycling
information, please contact your local authorities or the Electronic Industries Alliance: www.eiae.org.
Refer to the identifi cation/rating label located on the back panel of your product for its proper operating voltage.
FCC Regulations state that unauthorized changes or modifi cations to this equipment may void the user’s authority to
operate it.
Caution: To reduce the risk of electric shock, do not remove cover (or
back). No user serviceable parts inside. Refer servicing to qualifi ed service
personnel.
This symbol indicates important
instructions accompanying the product.
WARNING
The TV is unstable if it is not properly attached to the
base or mounted to the wall. Please follow the base
or wall mounting instructions provided in the User’s
Guide to ensure your safety.
Cable TV Installer: This reminder is provided to call your attention to Article 820-40 of the National Electrical Code
(Section 54 of the Canadian Electrical Code, Part 1) which provides guidelines for proper grounding and, in par tic u lar,
specifi es that the cable ground shall be connected to the grounding system of the building as close to the point of
cable entry as practical.
Important: This television is a table model and is designed to sit on a fi rm, fl at, surface. Don't place the TV on soft
carpeting or similar surface because the ventilation slots on the bottom of the unit will be blocked resulting in reduced
lifetime from overheating. To assure adequate ventilation for this product, maintain a spacing of 4 inches from the top
and sides of the TV receiver and 2 inches from the rear of the TV receiver and other surfaces.
Also, make sure the stand or base you use is of adequate size and strength to prevent the TV from being accidentally
tipped over, pushed off, or pulled off. This could cause personal injury and/or damage the TV. Refer to the Important
Safety Instructions on the next page.
Product Registration
Please fi ll out the product registration card (packed separately) and return it immediately. For US customers: Your RCA
Consumer Electronics product may also be registered at www.rca.com/television. Registering this product allows us to
contact you if needed.
Product Information
Keep your sales receipt to obtain warranty parts and service and for proof of purchase. Attach it here and record the
serial and model numbers in case you need them. These num bers are located on the product.
Model No. _____________________ Serial No.____________________ Purchase Date __________________
Licensed by BBE Sound, Inc. under one or more of the following US patents: 5510752, 5736897. BBE and BBE symbol are
registered trademarks of BBE Sound, Inc.
Important In for ma tion
Important Safety Instructions
Important Safety Instructions
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including
amplifi ers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with
one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or
the third prong is provided for your safety. If the provided plug does not fi t into your outlet, consult an electrician
for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the
point where they exit from the apparatus.
11. Only use attachments/accessories specifi ed by the manufacturer.
12. Use only with the cart, stand, tripod, bracket, or table specifi ed by the manufacturer, or sold with the
apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid
injury from tip-over.
13. Unplug this apparatus during lightning storms or when unused for long periods of time.
14. Refer all servicing to qualifi ed service personnel.
Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is
damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain
or moisture, does not operate normally, or has been dropped.
15. If an outside antenna or cable system is connected to the product, be sure the antenna or cable system is grounded
so as to provide some protection against voltage surges and built-up static charges. Section 810 of the National
Electrical Code, ANSI/NFPA No. 70-1984 (Section 54 of Canadian Electrical Code, Part 1) provides information
with respect to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an
antenna-discharge unit, size of grounding conductors, location of antenna-discharge unit, connection to grounding
electrodes, and requirements for the grounding electrode. See following example.
ANTENNA
LEAD IN
WIRE
GROUND CLAMP
ANTENNA
DISCHARGE UNIT
(NEC SECTION 810-20)
GROUNDING CONDUCTORS
(NEC SECTION 810-21)
ELECTRIC SERVICE
EQUIPMENT
GROUND CLAMPS
POWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ART 250, PART H)
Important Information i
Table of Contents
Important Safety Instructions ....................................... i
Chapter 1: Connections and Setup
Things to Consider Before You Connect ..................... 5
Protect Against Power Surges ................................ 5
Protect Devices from Overheating ........................ 5
Care and Cleaning ....................................................... 47
4
Chapter 1: Connections and Setup
Things to Consider Before You Connect
Protect Against Power Surges
• Connect all devices before you plug any of their power cords into the wall outlet or power
strip. NEVER plug your TV into an outlet that is controlled by a wall switch.
• Turn off the TV and/or device(s) before you connect or disconnect any cables.
• Make sure all antennas and cables are properly grounded. Refer to the Important Safety
Instructions at the beginning of the User's Guide.
Protect Devices from Overheating
• Don’t block ventilation holes on any of the devices. Arrange the devices so that air can
circulate freely.
• Don’t stack devices.
• If you place devices in a stand, make sure you allow adequate ventilation.
• If you connect an audio receiver or amplifi er, place it on the top shelf so the heated air
from it won’t fl ow around other devices.
Position Cables Properly to Avoid Audio Interference
• Insert each cable fi rmly into the designated jack.
• If you place devices above the TV, route all cables down the side of the back of the TV
instead of straight down the middle.
• If your antenna uses 300-ohm twin lead cables, do not coil the cables. Also, keep the twin
lead cables away from audio/video cables.
Use Indirect Light
Don’t place the TV where sunlight or room lighting will be directed toward the screen. Use soft
or indirect lighting.
Check Supplied Parts
Check that the following parts were packed with your product.
ON•OFF
TV
VOL
MENU
ZOOM-
CLEAR
INPUT
Remote control
Part # R301F1
Note: If you need to replace your remote, call 1-800-338-0376. A shipping and handling
fee, and the appropriate sales tax, will be charged upon ordering. Have your Visa,
MasterCard, or Discover Card ready.
PIP
DVD
SAT•AUX
GO BACK
CH
MUTE
INFO
+
CH CTRL
ZOOM+
GUIDE
PRESETS
?!+-
DEF
ABC
GHI
MNO
JKL
WXYZ
PQRS
TUV
SUB CH
_,.:=$
2 AA batteries
Power cord
Chapter 1 5
Graphics contained within this publication are for representation only.
Connections and Setup
ANTENNA/CABLE
INPUT
Coaxial cable
or
Outdoor or Indoor
antenna
Get the Picture
The fi rst part of connecting your TV is to get the picture, also known
as the signal. The back panel of your TV allows you to receive analog
and/or digital channels by using the ANTENNA/CABLE INPUT. See the
graphic to the left for the location of the jack.
Getting Channels
What You Need
• Antenna ("rabbit ears") or outdoor antenna with coaxial cable
OR
• Coaxial cable with cable service
A. Do you have an indoor or outdoor antenna? If not, go to step B. If
so, plug the antenna or coaxial cable from the wall outlet into the
ANTENNA/CABLE INPUT to receive free off-air local digital and
analog channels.
B. Do you have cable? If so, plug the coaxial cable from the wall
outlet into the ANTENNA/CABLE INPUT to receive your cable
channels.
C. Do you have a set-top box? If so, you need to call your cable
company or satellite service provider. They may use special cables
to allow you to view digital channels.
What You Need To Know
• Visit www.antennaweb.org to get help deciding what type of
antenna to use to receive the local digital channels available to
you. By entering where you live, this mapping program tells you
what local analog and digital stations are available using a certain
antenna.
• When you are ready to watch channels, the channel banner
displays the type of channel you're viewing. Look for a D at the
bottom of the screen for digital channels; look for an A for analog
channels. Go to page 15 for more information.
6 Chapter 1
Connections and Setup
Choose Your Connection
For additional assistance while using your RCA product, please visit www.rca.com/customersupport.
There are several ways to connect your TV. Please use the following chart to determine which connection is best
for you. Proceed to the appropriate page and connect your TV.
Jacks Used Cables Needed Go to...
R
AUDIO
L
(VID1)
AUDIO/VIDEO INPUT 1
VIDEO
Video1
Audio1 R and L
Audio/Video
page 8-9
R
AUDIO
L
Pr
Pb
COMPONENT INPUT 1 (CMP1)
Y
DVI AUDIO
INPUT
Y Pb Pr
Audio R and L
HDMI 1/DVI
INPUT
R
L
HDMI 1/DVI
Component Video
Audio
HDMI™
OR
HDMI™
+
HDMI/DVI adapter
+
Audio
page 8-9
page 10-11
VIDEO
VGA Video
VGA INPUT
VGA
page 12
Audio
AUDIO
HDMI, the HDMI logo, and High-Defi nition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC.
Audio
Chapter 1 7
Connections and Setup
Video (Basic) Connection
This is an example of a connection using the Video jack. Go to the top of page 9 for specifi c
instructions.
1
R
AUDIO
Don't forget: If necessary,
connect antenna or cable to
get a picture. Go to page 6 for
instructions.
L
(VID1)
AUDIO/VIDEO INPUT 1
VIDEO
3
2
INPUT
VIDEO
AUDIO
L
OUTPUT
S-VIDEO
R
AUDIO
LR
VIDEO
L
COMPONENT VIDEO
YPbPr
S-VIDEO
AUDIO
R
Component Video (Advanced) Connection
This is an example of a connection using the Component Video jacks. Go to the middle of
page 9 for specifi c instructions.
1
Don't forget: If necessary,
connect antenna or cable to
get a picture. Go to page 6 for
instructions.
R
AUDIO
L
Pr
Pb
COMPONENT INPUT 1 (CMP1)
Y
3
2
COMPONENT VIDEO
OUTPUT
YPbPr
VIDEO
AUDIO
R
L
AUDIO
LR
S-VIDEO
INPUT
VIDEO
AUDIO
S-VIDEO
R
L
8 Chapter 1
Connections and Setup
Red
Yellow
White
Composite cables are color
coded- Yellow= video;
Red= right audio; white=
left audio
Green
Blue
Red
Component Video cables
(Y Pb Pr) are color codedGreen, Blue and Red
Red
White
Audio cables are color
coded- Red= right audio;
white= left audio
ON•OFF button
ON•OFF
TV
VOL
MENU
ZOOM-
CLEAR
?!+-
PQRS
INPUT
PIP
DVD
SAT•AUX
GO BACK
CH
MUTE
INFO
+
CH CTRL
ZOOM+
GUIDE
PRESETS
DEF
ABC
GHI
MNO
JKL
WXYZ
TUV
SUB CH
_,.:=$
INPUT
button
Use these buttons
to view the picture
of the device you’ve
connected to the TV.
Connecting the Device with Video (Basic)
This connection allows you to connect a device that has a Video Out jack, for example, a
DVD player.
Note: If the device you're connecting also has Component Video jacks and you have
component video cables, we recommend you use the Component Video (Advanced)
Connection instead. See instructions below.
Using the example of a DVD player:
1. If necessary, connect your cable and/or off-air antenna as described on
page 6.
2. Connect your yellow video cable.
Connect a video cable to the VIDEO INPUT 1 jack on the back of the TV and to the
Video Output jack on the DVD player.
3. Connect your red and white audio cables.
Connect the audio (red and white) cables to the AUDIO INPUT 1 R and L jacks on the
back of the TV and to the Audio Output jacks on the DVD player.
Connecting the Device with Component Video (Advanced)
This connection allows you to connect a device that has Y Pb Pr jacks, for example, a DVD
player.
Using the example of a DVD player:
1.If necessary, connect your cable and/or off-air antenna as described on
page 6.
2.Connect your Y Pb Pr component video cables.
Connect three video cables or special Y Pb Pr cables to the COMPONENT INPUT 1
(CMP1) Y Pb Pr jacks on the back of the TV and to the Y Pb Pr outputs on the DVD
player.
3.Connect your red and white audio cables.
Connect the audio (red and white) cables to the CMP1 AUDIO R and L jacks on the
back of the TV and to the Audio Output jacks on the DVD player.
Viewing the Picture from the Connected Device
1. Plug in the TV (see page 13 for details) and the device, if they aren't already
plugged in.
2. Turn on the TV and the device you want to view, for example a DVD player.
3. Repeatedly press the INPUT button on the remote control until you see VID1 (if
connected to the VIDEO INPUT 1 jack) or CMP1 (if connected to the CMP1 jacks)
displayed at the bottom of the TV's screen. To go back to viewing TV channels, use the
number buttons to enter the channel or press CH+/- to go to the channel list from the
input list.
Note: If the picture from the DVD player appears black and white and your device
is connected to the VIDEO Input, you might be tuned to the wrong input. Make sure
you press INPUT until you see VID1 displayed at the bottom of the TV's screen.
• If you're done
connecting devices to
your TV, go to page 13
to complete the Initial
Setup.
• To continue
connecting devices, go
to the next page.
Chapter 1 9
Connections and Setup
HDMI/DVI Connection
This is an example of a connection using the HDMI/DVI jack.
*
HDMI 1/DVI
INPUT
*Don't forget: If necessary, connect
antenna or cable to get a picture. Go
to page 6 for instructions.
Device with HDMI
Pb
Y
Video Out
Pr
R
Audio Out
R
DVI AUDIO
INPUT
L
C
A
B
Device with DVI
L
HDMI Out
OR
DVI Out
L
Audio Out
R
10 Chapter 1
Connections and Setup
Connecting the Device
High-Defi nition Multimedia Interface (HDMI) technology is an uncompressed digital connection
that carries both video and audio data by way of an integrated mini-plug cable. Since HDMI
technology is based on Digital Visual Interface (DVI), the jack on the back of your TV is also
compatible with devices that have a DVI output jack.
Using the example of a set-top box:
• If your set-top box has an HDMI jack, connect an HDMI cable.
HDMI cable
HDMI cable
HDMI/DVI adapter
Red
Connect an HDMI cable to the HDMI1/DVI Input jack (or the HDMI2 jack if it is more
convenient) on the back of the TV and to the HDMI Out jack on the back of the
device.
–OR–
• If your set-top box has a DVI jack, connect an HDMI cable and an
HDMI/DVI adapter.
A. Connect an HDMI cable to the HDMI1/DVI Input jack on the back of the TV.
B. Attach an HDMI/DVI adapter to the end of the HDMI cable, then connect the
adapter to the DVI Out jack on the set-top box.
C. Since you’re using an HDMI/DVI adapter, you need to connect Audio left and right
cables to the DVI AUDIO R and L jacks on the back of the TV and to the R and L
jacks on the back of the device.
Audio cables are color
coded- Red= right audio;
White= left audio
ON•OFF button
ON•OFF
TV
VOL
MENU
ZOOM-
CLEAR
?!+-
PQRS
INPUT
PIP
DVD
SAT•AUX
GO BACK
MUTE
INFO
+
GUIDE
PRESETS
DEF
ABC
GHI
MNO
JKL
WXYZ
TUV
SUB CH
_,.:=$
INPUT
button
Use these buttons
to view the picture
of the device you’ve
connected to the TV.
White
CH
CH CTRL
ZOOM+
Viewing the Picture from the Connected Device
The device in this connection is connected to the HDMI1/DVI jack. To view this device:
1. Plug in the TV (see page 13 for details) and the device, if they aren't already plugged
in.
2. Turn on the TV and the device you want to view, for example a set-top box.
3. Repeatedly press the INPUT button on the remote control until you see HDMI1
displayed at the bottom of the TV's screen. To go back to viewing TV channels, use
the number buttons to enter the channel or press CH+ or CH- buttons.
• If you're done connecting
devices to your TV, go to
page 13 to complete the
Initial Setup.
• If you experience HDMI
problems, go to the HDMI
Troubleshooting section on
page 42.
Chapter 1 11
Connections and Setup
VGA Connection
This is an example of a connection using the VGA jacks.
1
Don't forget: If necessary,
connect antenna or cable to
get a picture. Go to page 6 for
instructions.
2
3
VIDEO
AUDIO
VGA INPUT
Connecting the Device
This connection allows you to connect to a personal computer.
1. If necessary, connect your cable and/or off-air antenna as described on
page 6.
2. Connect your monitor cable.
Connect one end of a 15-pin monitor cable to the VGA VIDEO jack on the TV and the
other end to the PC's video output jack. Note, if your PC's video output isn't 15-pin, you'll
need an adapter that can connect to a 15-pin monitor cable.
3. Connect your audio cable.
Connect a 3.5 mm stereo mini pin cable (sometimes referred to as 1/8" stereo mini pin) to
the VGA AUDIO jack on the back of the TV and the other end to the Audio Output jack on
the PC.
Notes: The maximum resolution is 1024 x 768. Be sure to set your PC to the correct
monitor output setting.
To hear sound from the TV while using the PC, press the PRESETS button. Highlight PC
Sound source and press the right arrow to choose TV tuner.
Viewing the PC
1. Plug in the TV and the PC, if they aren't already plugged in.
2. Turn on the TV and the PC.
3. Repeatedly press the INPUT button on the remote control until you see VGA displayed at
the bottom of the TV's screen. To go back to viewing TV channels, use the number buttons
to enter the channel or press CH+ or CH- buttons.
12 Chapter 1
Connections and Setup
Plug in the TV
Plug the end of the power cord into the back of the TV. Plug the other end into a grounded
wall outlet. Insert the plug completely into the outlet. Do not plug into an outlet controlled by
a light switch.
Put Batteries in the Remote
• Remove the battery compartment cover from the back of the remote by pushing the tab
and lifting off the cover.
• Insert two fresh batteries. Make sure the polarities (+ and -) are aligned correctly.
• Replace the cover.
Turn on the TV
Turn on your TV by pressing the Power button on the front of the TV or ON•OFF on the
remote control.
VOL
MENU
ZOOM-
CLEAR
TV
INPUT
?!+-
PQRS
How to Use the Remote Control to
ON•OFF
PIP
DVD
SAT•AUX
GO BACK
CH
MUTE
INFO
+
CH CTRL
ZOOM+
GUIDE
PRESETS
DEF
ABC
GHI
MNO
JKL
WXYZ
TUV
SUB CH
_,.:=$
OK
button
Arrows
Complete the Initial Setup
The technical term is “Navigation” – how you move through the onscreen menus. The theory is the same throughout the menu screens:
highlight your choice and select it.
To highlight a menu item, press the arrow buttons on the remote to
highlight one of the items listed on the screen. Use the up or down
arrow button to move up or down. Use the right or left arrow button
to view other selections for a menu choice or to display a sub-menu.
More than one selection displays, for example, On...; a menu choice
with a sub-menu displays dots (...).
Note: Highlighted means that the menu item stands out from
other menu items on the list (appears darker, brighter, or a
different color).
Tip
To access the setup menus manually, press MENU and
choose Setup.
Chapter 1 13
Connections and Setup
Complete the Initial Setup
The menu system in your TV allows the TV’s features to work properly. The fi rst time you turn
on your TV, the language screen appears.
Set the Menu Language
The fi rst part of the setup allows you to select your preferred language
English
Français
Español
for the menu system.
If English is your preferred language, press OK. To choose another
language, press the down arrow button until that language is
highlighted, and press OK.
Complete Channel Setup
Make sure you've connected the TV to cable and/or an off-air signal
before you start the next part of the setup.
Channel setup
Go back
Signal type Cable...
Auto Channel search ...
Channel setup
Go back
Signal type Cable...
Auto Channel search Running...
Progress
Analog Channels found 10
Digital Channels found 05
Auto Channel search in progress. Press CLEAR to cancel
Any channels already found will be stored.
If you have analog and digital channels,
the TV's search might take longer since it is
looking for both.
Channel setup
Go back
Signal type Cable...
Auto Channel search ...
Auto Channel search complete. Press OK to review channels.
Press CLEAR to exit, MENU for Setup menu.
Once a channel search is complete, the
Channel setup menu looks like this.
Set the Signal Type
If you connected Cable to your ANTENNA/CABLE jack, the option is
chosen for you and you can press the down arrow button to continue.
To choose Antenna, press the right arrow button and then press the
down arrow button to continue.
Complete the Channel Search
With Auto Channel Search highlighted, press OK to begin the channel
search.
There are several things to be aware of when the TV's searches
for channels.
If you chose Cable as your signal type, the search takes a while
because it's looking for analog and digital channels, and then it's
removing scrambled channels found. Here is what happens during the
search:
1. The search fi rst looks for digital channels and places the number
of channels found next to Digital Channelsfound. This number
will probably seem like a lot. This is because the number includes
both scrambled (for example, Pay Per View) and non-scrambled
channels. These channels are dependent upon what your cable
company is sending.
2. The search then looks for analog channels and places the number
of channels found next to Analog Channelsfound.
3. The search might appear as if it is complete, but as long as the
search says Running, it is still in progress. What's happening at
this point is the TV is removing scrambled channels from the
channel list. When the search is fi nally complete, the Channel setup menu will look like the picture to the left. To exit the menu
system, press CLEAR.
14 Chapter 1
Connections and Setup
List and Labels
Go back
Channel Number 10
In Channel List
Channel Label ABC
Favorite Channel
10 CBS
A
Look for the A at the bottom of the screen to
see if you're watching an analog channel.
You might fi nd there are still some channels in your list that are
unavailable to view. To get rid of these channels, press MENU and
choose Setup. Highlight and select List and Labels. Note that removing
channels from your channel list may be time consuming, so you might
want to do it later. Go to page 36 for details on editing your channel
list.
What To Expect
Watching TV
• Remember: Look for an A at the bottom of the screen to see if
you're watching an analog channel.
Analog video is sent in a 4/3 format, which your TV displays these
channels in a 16/9 format. Press the ZOOM+/- button to view the
different formats available. Go to page 32 for more explanation of
screen formats.
• Remember: Look for a D at the bottom of the screen to see if
you're watching a digital channel.
Most digital video is sent in a 16/9 format which does fi ll your
screen, but sometimes is sent in 4/3 which does not fi ll your
screen. It depends on how the station or source device is
formatting the video. If there are bars on-screen, press the
ZOOM+/- button to try a different format that may eliminate
the bars. Some bars can't be removed because of the way
the format is sent by the broadcaster. Go to page 32 for more
explanation of screen formats.
10-1 CBS
D
Look for the D at the bottom of the screen to
see if you're watching a digital channel.
Changing Channels
• Digital channels can have both primary channels (like the analog
channel number) and sub-channels. To tune to a digital channel
with a sub-channel, such as 10-1 as shown in the graphic to the
left, enter the primary channel number (10), then press either the
right arrow or the SUB CH button. Enter the sub-channel number
(1) and press OK.
• Depending upon the type of signals you have connected to your
HDTV, you might notice that the channels change slower than
you’re used to. This is perfectly normal. Digital cable channels
sometimes take longer to tune.
Chapter 1 15
Connections and Setup
R
AUDIO
L
(VID1)
AUDIO/VIDEO INPUT 1
VIDEO
R
AUDIO
L
Pr
Pb
COMPONENT INPUT 1 (CMP1)
Y
R
AUDIO
L
Pr
Pb
COMPONENT INPUT 2 (CMP2)
Y
R
AUDIO
L
AUDIO OUTPUT
FIXED/VARIABLE
VIDEO OUTPUT
DIGITAL AUDIO
OUTPUT (Coaxial)
ANTENNA/CABLE
INPUT
HDMI 2
INPUT
HDMI 1/DVI
INPUT
R
DVI AUDIO
INPUT
L
VIDEO
AUDIO
VGA INPUT
Explanation of Jacks (in alphabetical
order)
This section describes the jacks on the back panel of your TV. There
are several ways to connect devices.
ANTENNA/CABLE INPUT Lets you connect a coaxial cable to
receive the signal from your antenna, cable, or cable box.
AUDIO/VIDEO INPUT 1 (VID1) Lets you connect a device that has
composite video jacks, such as a VCR or DVD player.
• L AUDIO Provides left audio connection when using the VIDEO
INPUT 1 jack. The left audio connector is usually white.
• R AUDIO Provides right audio connection when using the
VIDEO INPUT 1 jack. The right audio connector is usually red.
COMPONENT INPUTS Lets you connect a device that has
component video jacks, such as a DVD player.
• CMP1 Y Pb Pr (Component Video) Provides optimum picture
quality because the video is separated into three signals. Use three
video-grade or component video cables for the connection. When
using CMP1 Y Pb Pr, make sure you connect left and right audio
cables to the CMP1 L and R AUDIO jacks.
• CMP1 L AUDIO Provides left audio connection when using the
CMP1 video inputs. The left audio connector is usually white.
• CMP1 R AUDIO Provides right audio connection when using the
CMP1 video inputs. The right audio connector is usually red.
• CMP2 Y Pb Pr (Component Video) Same as described for
CMP1 Y Pb Pr and CMP1 Audio above. Make sure you connect the
left and right audio cables to the CMP2 L and R AUDIO jacks.
DIGITAL AUDIO OUTPUT (Coaxial) Use a digital coaxial cable to
connect your TV to a compatible audio receiver.
FIXED/VARIABLE AUDIO OUTPUT Use left and right audio cables
to connect your TV to a compatible audio receiver. Make sure you set
the Audio Output option correctly in the Advanced Sound menu. Go
to page 35 for more information.
HDMI1/DVI INPUT Lets you connect a device, such as a digital
cable box, with an HDMI or a DVI output.
Visual Interface) Provides an uncompressed digital connection
that carries both video and audio data by way of an integrated
mini-plug cable. Since HDMI technology is based on Digital Visual
Interface (DVI), the jack on the back of your TV is also compatible
with DVI devices.
• DVI AUDIO L (used for DVI only) Provides left audio
connection when using the HDMI1 jack for DVI. The left audio
connector is usually white.
• DVI AUDIO R (used for DVI only) Provides right audio
connection when using the HDMI1 jack for DVI. The right audio
connector is usually red.
Note: Remember to connect the left and right audio cables
because the DVI cable carries only the picture signal, not the
sound.
16 Chapter 1
Connections and Setup
HDMI2 Input Lets you connect a device, such as a digital cable box, with an HDMI output.
VGA INPUT Connect your computer, or other device with a VGA output, to this jack using a
15 pin D-sub cable.
VGA AUDIO (Stereo mini jack) Use to obtain sound when a PC is connected to the VGA
jack. Use a 3.5 mm stereo mini pin cable (sometimes referred to as 1/8” stereo mini pin) to
connect a PC to your TV.
VIDEO OUT PUT Connect a VCR or DVD-recorder to record digital and analog programs
from the ANTENNA/CABLE INPUT (excluding copy-protected programs and component video
formats) while the TV is turned on. You must leave the TV on the same channel you are
recording.
Buttons and Other Jacks On Your TV
Side Input Jacks
(Headphones) Allows you to connect headphones to listen to the sound coming from the
TV. To adjust volume control of the headphones, go to the Headphone Settings option in the
Sound menu.
S-VIDEO INPUT Allows you to connect an S-Video cable from another device. Make sure you
also connect audio cables from the device to the TV. To access a device connected to the
S-VIDEO jack, press the INPUT button on your remote until VID2 appears at the bottom of the
screen.
VIDEO INPUT 2 Receives video from another device such as a camcorder, video game
console, VCR, or DVD player. To access a device connected to the VIDEO jack, press the INPUT
button on your remote until VID2 appears at the bottom of the screen.
Note: Do not connect an S-Video and a regular video cable to the side jacks at the same
time.
AUDIO L and R Receives audio from another device such as a camcorder, video game
console, VCR, or DVD player. Use when connecting to the VIDEO or S-VIDEO Input.
Side Panel Buttons
If you cannot locate your remote, you can use the side panel buttons of your TV to operate
many of the TV’s features.
POWER Turns the TV on and off.
MENU/OK Brings up the TV Main menu. When in the menu system, displays sub-menus and
selects highlighted items.
>
VOL Increases the volume. In the TV menu system, acts like the right arrow button on the
remote control and adjusts menu controls.
>
VOL Decreases the volume. In the TV menu system, acts like the left arrow button on the
remote control and adjusts menu controls.
>
CH Scans up through the channel list.
>
CH Scans down through the channel list.
Chapter 1 17
Chapter 2: Using the Remote Control
The Buttons on the Remote Control
Alphanumeric Buttons Enter channel numbers; time settings; and
ON•OFF
TV
SAT•AUX
VOL
MENU
ZOOM-
CLEAR
?!+-
GHI
PQRS
INPUT
Remote control part number R301F1
GO BACK
MUTE
INFO
PRESETS
ABC
JKL
TUV
_,.:=$
DVD
PIP
+
DEF
MNO
WXYZ
SUB CH
CH
CH CTRL
ZOOM+
GUIDE
Note: If you need to replace your
remote, call 1-800-338-0376. A
shipping and handling fee, and the
appropriate sales tax, will be charged
upon ordering. Have your Visa,
MasterCard, or Discover Card ready.
options with letters, such as the Message option, using these buttons.
To enter a channel, press the number buttons and press OK (or just let
the entry timeout).
To enter a digital channel with a sub-channel, enter the main channel,
then press the SUB CH or right arrow button to enter the sub-channel
and press OK.
Arrows Used to highlight different items in the TV menu and to
adjust the menu controls. When viewing a channel, press the left
or right arrow to change the screen format: 4/3, 16/9 zoom,
Cinerama, and 16/9. Go to page 32 for more information on screen formats.
CH + or CH - Scans up or down through the current channel list.
Press once to change the channel up or down; press and hold to
continue changing channels.
CH CTRL This button doesn't have a function for your model of TV.
CLEAR Removes any menu or display from the screen and returns
you to normal viewing.
DVD Places the remote in DVD mode. If Auto Tuning is enabled,
turns on the TV and tunes it to the DVD Channel. This button lights
when you press a valid button in DVD mode (see Modes of Operation
on page 21 for more details).
GO BACK Returns you to the previous channel.
GUIDE Displays an electronic program guide (when available).
INFO If no menus are on-screen, displays the channel banner; press
again to clear the screen.
INPUT
Accesses the available video input channels (VID1, VID2,
CMP1, CMP2, VGA, HDMI1 and HDMI2). To resume TV viewing, press
number buttons to enter the channel or press CH+ or CH- buttons.
the
MENU Brings up the Main menu.
MUTE Reduces the TV’s volume to its minimum level. Press again
to restore the volume. To program this button to work with an audio
system, follow the instructions for Volume Punchthrough Feature on
page 21.
OK When in the menu system, selects highlighted items.
ON•OFF When in TV mode, turns the TV on or off. If in another
mode (SAT•AUX or DVD) and programmed, will turn the device on or
off.
PIP This button doesn't have a function for your model of TV.
PRESETS
Displays Picture and Sound preset; CC Settings; Current
Audio Track, PC Sound source; and CH+/CH- buttons (which
works with the Favorite Channels option. Go to page 37 for more
information).
REVERSE, PLAY, FORWARD, RECORD, STOP, PAUSE (buttons at
bottom of the remote) If programmed, provides transport control
for some remote-controllable devices, for example, VCRs or DVD
players.
18 Chapter 2
Graphics contained within this publication are for representation only.
Using the Remote Control
SAT•AUX Places the remote in SAT•AUX mode. If Auto Tuning is enabled, turns on the TV
and tunes it to the satellite or cable box Video Input Channel. This button lights when you
press a valid button in SAT•AUX mode (see Modes of Operation on page 21 for more details).
SUB CH When entering a digital channel that has a subchannel, press this button to access
the subchannel entry fi eld. Once the channel is entered, press the OK button to tune to the
channel.
TV Turns on the TV and puts the remote in TV mode. Also displays current status.
VOL – or VOL + Decreases or increases the TV’s volume. To program this button to work with
an audio system, follow the instructions for Volume Punchthrough Feature on page 21.
ZOOM– or ZOOM + When viewing a channel, press to change the screen format: 4/3, 16/9
zoom, Cinerama, and 16/9. Go to page 32 for more information on screen formats.
Using the INPUT Button
Use the INPUT button to scroll through the available video input channels and view devices
you have connected to the TV.
1. Make sure the device you want to view is turned ON.
2. Press INPUT to tune to an available video input source and view the device.
3. To return to the previous channel, press INPUT until you return to the channel.
ON•OFF
MUTE
INFO
_,.:=$
PIP
DVD
CH
+
CH CTRL
ZOOM+
GUIDE
DEF
ABC
MNO
JKL
WXYZ
TUV
SUB CH
VOL
MENU
ZOOM-
CLEAR
TV
INPUT
SAT•AUX
GO BACK
PRESETS
?!+-
GHI
PQRS
The darkened buttons are the device buttons
that can be programmed.
Programming the Remote to
Operate Other Devices
The universal remote can be programmed to operate many brands of
remote-controllable VCRs, audio devices, DVD players, cable boxes,
satellite receivers and other devices. In addition to being programmed
to operate your television, it’s already programmed to operate some
RCA devices.
Notes: The TV button can’t be programmed on this remote to
control any device; it controls only this TV.
The remote may not be compatible with all models of all brands
of devices. It also may not operate all functions of your device.
Find Out If You Need to Program the Remote
To determine whether the universal remote needs to be programmed
to operate one of the devices connected to your TV, such as a VCR, do
the following:
1. Turn on the device (in this example, a VCR).
2. Point the remote at the device.
3. Press the corresponding device button (in this example, VCR).
4. Press ON•OFF to see if the VCR responds. If the VCR doesn’t
respond, you need to program the remote to operate it.
Chapter 2 19
Using the Remote Control
Programming the Remote
ON•OFF
MUTE
INFO
ABC
JKL
TUV
_,.:=$
PIP
DVD
CH
+
CH CTRL
ZOOM+
GUIDE
DEF
MNO
WXYZ
SUB CH
VOL
MENU
ZOOM-
CLEAR
TV
INPUT
SAT•AUX
GO BACK
PRESETS
?!+-
GHI
PQRS
You’ll use these darkened buttons for Direct
Entry.
There are three ways to program the remote control to operate other
devices: Direct Entry, Manual Code Search, and Automatic Code Search. If you have recently purchased the device you want to control
or if the device has many codes, you might want to try the manual
code search fi rst.
Using Direct Entry
1. Turn on the device you want to control.
2. Look up the brand and code number(s) for the device in the code
list at the end of this section.
3. On your remote control, simultaneously press and hold the
ON•OFF and MUTE buttons (approximately 3 seconds) until a
device button remains lit. Then release the buttons.
4. Press and release the device button (SAT•AUX or DVD) you want
to program.
5. Enter a three digit code from the code list.
6. To test the code you’ve programmed for that device button, point
the remote at the device and then press ON•OFF to see if the
device responds to the remote control.
If the device turns off, you’ve entered the correct programming
code for your device. Circle the code you entered for future
reference.
If the device doesn’t turn off, repeat these steps until you’ve tested
all codes for your device’s brand or try to run a manual code
search.
Using Manual Code Search
Note: Before using manual code search, you must use Direct Entry fi rst. This lets the
remote know which type of device to begin searching codes. Then proceed with the
following steps.
1. Turn on the device you want to control.
2. On your remote control, simultaneously press and hold the ON•OFF and MUTE buttons
(approximately 3 seconds) until a device button remains lit. Then release the buttons.
3. Press and release the device button (SAT•AUX or DVD) you want to program.
4. Repeatedly press and release the ON•OFF button, watching for the device to respond.
If it does turn off, press and release the OK button within 3 seconds to save the code. If
you accidentally passed the code before saving it, press the left arrow button to backtrack
through the codes; then use the right arrow button to go forward through the codes again.
When all codes have been searched, the device button fl ashes 3 times, then the remote exits
manual code search and returns to normal operation.
Using Automatic Code Search
1. Turn on the device you want to control.
2. On your remote control, simultaneously press and hold ON•OFF and MUTE
(approximately 3 seconds) until a device button remains lit. Then release the buttons.
3. Press and release the device button you want to program.
continued on next page...
20 Chapter 2
Using the Remote Control
4. Press and release the ON•OFF button once. There is a delay of approximately 6 seconds
before the remote starts the code search.
The device buttons blinks each time the remote control sends a code to test with your
device. Keep pointing the remote at the device.
5. Once the device turns off, quickly press the OK button to save the code.
6. If you accidentally passed the code before saving it, press the left arrow button to backtrack through the codes; then use the right arrow button to go forward through the codes
again.
When all codes have been searched, the device button fl ashes 3 times, then the remote exits
automatic code search and returns to normal operation.
How to Use the Remote After You’ve
Programmed It
Once the remote has been programmed successfully, you are ready to use it to operate your
devices.
To operate the device:
1. Press the appropriate device button (SAT•AUX or DVD) to set the remote to control the
device, for example, press DVD to control your DVD player.
2. Press ON•OFF to turn the device ON or OFF.
3. Use the remote buttons that apply to that device.
Note: The remote control may not be compatible with all brands and models of devices.
Modes of Operation
The button corresponding to the mode the remote is in lights up when you press any button
that works in that mode. For example, if you’re in TV mode and you press the VOL+ button,
the TV button lights up. This tells you that the command to increase the volume is being sent to
the TV (and not the satellite receiver, for example).
Volume Punchthrough Feature
You may fi nd this feature helpful if you’ve connected your devices to an audio system, and you
want to use the TV’s remote control to operate the volume for a device that is connected to the
audio system. An example follows:
Let’s say you’ve connected your DVD player to your audio system. You’ve also programmed
your TV remote control to operate your DVD player. Since the DVD player sends its volume
through the audio system, you would have to bounce back and forth between two remote
controls: the audio system’s remote to adjust the volume and the TV’s remote control to operate
the DVD player.
The Volume Punchthrough feature eliminates the need for you to use two remote controls and
saves a button press when you’re using the TV remote to adjust the volume. In effect, you are
telling the TV remote to retrieve and send volume commands from the audio system whenever
the TV remote is in DVD mode.
Chapter 2 21
Using the Remote Control
Therefore, after you’ve successfully set up the Volume Punchthrough feature, whenever the TV
remote is in DVD mode (press the DVD button) and you want to adjust the volume, you only
have to press the VOL +/- or MUTE buttons. Follow the instructions below to set up Volume
Punchthrough.
1. On your remote control, simultaneously press and hold the ON•OFF and MUTE buttons
(approximately 3 seconds) until a device button remains lit. Then release the buttons.
2. Press and hold the MUTE button until the device button blinks off, then release the MUTE
button.
3. Press and release the device button that you programmed to operate the audio system
(receiver or amplifi er).
4. Press and release the MUTE button.
5. Now, test it by turning on your audio system.
6. Turn on the device that is connected to the audio system (satellite receiver, for example).
7. Put the TV’s remote in SAT•AUX mode by pressing the SAT•AUX button.
8. Press VOL+ or VOL-. The volume from the audio system should increase or decrease
accordingly.
Deleting ALL Volume Punchthrough Commands
To delete all programmed Volume Punchthrough settings and return the remote control back to
the factory defaults:
1. Simultaneously press and hold the ON•OFF and MUTE buttons (approximately 3 seconds)
until a device button remains lit. Then release the buttons.
2. Press and hold the MUTE button until the device button blinks off, then release the MUTE
button.
3. Press and release the MUTE button until the device button light turns off.
4. The remote returns to normal Volume/Mute control.
22 Chapter 2
Using the Remote Control
Remote Code List
Note: The codes are programmable to any of the device buttons (SAT•AUX or DVD) on the remote.
SONY .........................................................................585
Chapter 2 25
Chapter 3: Using the TV's Features
Channel Banner
There are several indicators that might appear when you press the INFO button on the remote.
This display is called the Channel Banner. The following list describes the items on the Channel
Banner screen (left to right and top to bottom).
Stereo SAP CC
10 CBS 4/3 Format Z
D
Z
z
00:25
6:05 PM
TV-14 The current program rating.
Stereo Stereo appears when the current channel is broadcasting in stereo.
Mono appears when the current channel is broadcasting inmono.
SAP The current channel is broad cast ing SAP (Second Audio Program)
information.
CC Closed Captioning is available on the current channel.
D 10 CBS The D means it's a digital channel. If it's an analog channel, A
is displayed. The channel, sub-channel (if available for digital
channels) and program (only for digital channels) you're currently
viewing are displayed.
4/3 or 16/9 format Current screen format. If there are bars on-screen you might be able
to get rid of them by pressing the ZOOM buttons on the remote. Go
to page 32 for more information on screen formats.
Zzz 00:25 Current time left on sleep timer, if the sleep timer is set.
6:05 pm Current time.
Autotuning
Note: This feature only works with other RCA devices.
The Autotuning feature automatically tunes the TV to the correct video input channel for
different devices you have connected to your TV. When you set up Autotuning in the menu
system you don’t have to remember to change your TV to the VID1 input, for example, when
you want to watch a tape on the VCR. To set up the Autotuning feature:
Setup
Go back
Channel setup ...
List and Labels ...
Autotuning ...
Closed caption ...
Preferences ...
Message ...
1. Press MENU (the MAIN MENU appears).
2. Highlight Setup and press OK on your remote control.
3. Highlight Autotuning and press OK.
4. Choose which device button you would like to set:
Set VCR Channel If the DVD or SAT•AUX button is programmed
to your VCR, lets you set up the channel the TV tunes to when
you press the corresponding button.
Set DVD Channel Lets you set up the channel the TV tunes to
when you press the DVD button.
Set SAT•AUX Channel Lets you set up the channel the TV tunes
to when you press the SAT•AUX button.
26 Chapter 3
Graphics contained within this publication are for representation only.
Using the TV’s Features
Autotuning
Go back
Set VCR Channel VID1...
Set DVD Channel CMP1...
Set SAT-AUX Channel HDMI1...
5. Press the right arrow button to select the choice that matches the
way you have the device connected to this TV.
You can select from the following inputs or channels:
Disabled Choose this if you don’t have a device connected to the
TV, or if you don’t want the TV to automatically tune to the correct
channel/input when you’re using this device.
Channel 3 or 4 Device is connected to the ANTENNA/CABLE jack
on the back of the TV, and you want the TV to tune to channel
3 when you press the corresponding button on the remote.
Reminder: make sure the device’s Channel 3/4 switch is set to
channel 3.
VID1 or VID2 (Video Input) Device is connected to the VIDEO
INPUT 1 jack on the back of the TV or the VIDEO INPUT 2 jack
on the side of the TV and you want the TV to tune to the VIDEO
input channel when you press the corresponding device button.
CMP1 or CMP2 (Component Video Input) Compatible
component video source, such as an HDTV tuner or satellite
receiver, is connected to the three COMPONENT VIDEO INPUT
jacks (Y Pb Pr) on the back of the TV and you want the TV to tune
to the component video input channel (CMP1 or CMP2) when you
press the corresponding device button.
VGA Device is connected to the VGA jack on the back of the TV
and you want the TV to tune to the VGA input channel when you
press the corresponding device button
HDMI1 or HDMI2 Device is connected to the HDMI1/DVI or
HDMI2 jack on the back of the TV and you want the TV to tune to
the HDMI input channel when you press the corresponding device
button.
Chapter 3 27
Using the TV’s Features
Parental Controls and V-Chip
The choices in the US V-Chip and Canada V-Chip menus involve software inside your TV
(referred to as V-Chip) which allows you to block TV programs and movies. TV programs can
be blocked by age-based ratings, such as TV-MA, which is explained on page 30. If available,
TV programs can also be blocked by content, such as adult language (L). This is explained on
page 30. Movies can only be blocked by age-based ratings. This is explained on page 31.
Once you block programs, you can unblock programs by entering a password.
By default, the software inside your TV is turned off or unlocked. For instructions to lock
V-Chip, see below.
Note: Parental control settings are not available for HDMI1, HDMI2, CMP1, or CMP2
inputs. These settings must be set in the connected device's parental controls.
How V- Chip Works for USA and Canada
V-Chip reads the program’s age-based rating (TV-MA, TV-14, etc.) and content themes [(Violence
(V), Adult Language (L), etc.)]. If you have blocked the rating and/or content themes that the
program contains, you will receive the message This channel is blocked. Change channel or
press OK to enter your password and temporarily deactivate the parental controls.
Broadcasters are not required to provide content themes, so programs received with no content
themes will only be blocked if you block their age-based rating. You can also block out
programs that have been given an Exempt rating, and programs that are considered unrated.
Go to page 44 for the US and Canada ratings explanations.
Parental control
Go back
Lock Parental Control - - - -
Select Channel 51 MTV
Block Channel
Front Panel Block
US V-Chip ...
Canada V-Chip ...
Unrated/Exempt Ratings View...
Lock/Unlock Parental Controls
Selecting this option lets you lock and unlock parental controls settings
using a password.
If you do not lock parental controls, none of the settings for
V-Chip, Channel Block, or Front Panel Block will take effect.
If you forget your password, turn off the TV. Simultaneously press
and hold VOL v on the side panel and CLEAR on the remote for 10
seconds. Next time you enter the Parental control menu enter a new
password.
28 Chapter 3
Using the TV’s Features
The V-Chip Rating Screen
The following is an example of where items are located within the Rating Limit screen.
Rating Status Field
Lets you select whether the status of the age-based
You can automatically block all program ratings above a specifi ed agebased rating level.
1. Choose Parental control from the Main Menu. If Parental controls
have previously been locked, you must enter your password.
2. Highlight and select US V-Chip. Then select TV ratings.
3. Press the up or down arrow button to scroll to the rating
corresponding with the lowest rating you do not want the child to
watch.
4. Press the OK button to toggle between View and Block. The status
for the rating and all higher ratings automatically changes to Block.
5. Use the up/down arrow buttons to highlight Go back and press
OK.
6. Select Lock Parental Controls from the Parental Control menu for
rating limits to take effect.
Note: If you forget your password, turn off the TV.
Simultaneously press and hold VOL v on the side panel and
CLEAR on the remote for 10 seconds. Next time you enter the
Parental control menu enter a new password.
To view age-based ratings after you've locked them, follow the same
steps as above to unlock.
You can block programs based on their content. (Content is
represented by the D, L, S, V and FV on your screen.) When you block
a content theme for a particular rating, you automatically block that
content theme for higher rated programs as well.
To block program content:
1. Determine the content themes you want to block.
2. Press the down arrow button to scroll to the rating whose content
theme you want to change.
3. Press the right arrow button to move the highlight to a particular
content theme.
4. Press the OK button to change its status to lock. (In the example
to the left, you block the language (L) corresponding with TV-14.
The language for TV-MA is blocked as well.)
Notes: Broadcasters are not required to provide content
themes or age-based ratings.
You must remember to lock Parental controls for rating limits
to take effect.
To view content theme after you've locked them, follow the same
steps as above to unlock. Note that if you unlock the language
corresponding with TV-14, the language for TV-MA doesn't unlock.
You have to unlock the content theme status for each rating separately.
English ratings
Go back
Status
18+ Block
14+ Block
PG Block
G View
C8+ View
C View
French ratings
Go back
Status
18 ans+ Block
16 ans+ Block
13 ans+ Block
8 ans+ View
G View
C View
Blocking Canadian V-Chip Ratings
If you receive Canadian programs you can block Canadian English and
French V-Chip by ratings only. When you block a particular rating, you
automatically block the higher rated programs as well.
To block Canadian English and French program ratings:
1. Select Canada V-Chip from the Parental control menu.
2. Highlight English ratings or French ratings and press OK.
3. Determine the rating you want to block.
4. Press the down arrow button to scroll to the rating you want to
change.
5. Press the OK button to change its status to block (all ratings above
the one you selected change to block).
30 Chapter 3
Using the TV’s Features
Movie ratings
Go back
Status
NR (No Rating) Block
X Block
NC-17 Block
R View
PG-13 View
PG View
G View
Parental control
Go back
Lock Parental Control - - - -
Select Channel 51 MTV
Block Channel
Front Panel Block
US V-Chip ...
Canada V-Chip ...
Unrated/Exempt Ratings View...
V-Chip Movie Rating Limit
Set movie rating limits by blocking movies rated above a specifi ed
level.
To access the Movie Rating Limit menu:
1. Press MENU on the remote control (the TV's Main Menu appears).
2. Select Parental Control.
3. Select US V-Chip.
4. Select Movie Ratings.
Blocking Movie Ratings
Once you are in the Movie Ratings menu, follow the same steps
described for blocking Canadian ratings.
Block Channels
Turn this option on to block the channel you choose in the Select
Channel option.
Use the number buttons to enter the channel you want to block, then
press the down arrow button. Press OK to place a check mark in
the Block Channel box to block the channel. When you tune to that
channel you'll need to enter a password to view the channel if the TV
is locked.
Parental control
Go back
Lock Parental Control - - - -
Select Channel 51 MTV
Block Channel
Front Panel Block
US V-Chip ...
Canada V-Chip ...
Unrated/Exempt Ratings View...
Parental control
Go back
Lock Parental Control - - - -
Select Channel 51 MTV
Block Channel
Front Panel Block
US V-Chip ...
Canada V-Chip ...
Unrated/Exempt Ratings View...
Front Panel Block
Select this option to block (disable) or unblock (enable) the TV’s side
panel buttons so that they can't be used by someone, like a young
child. The remote still tunes to any channel. If you're using this to
keep children from changing channels, remove access to any remote
that is capable of operating the television while you have the front
panel blocked.
Don’t forget to lock parental controls after you change the status. If
you don’t, the front panel block will not take effect.
Blocking Unrated/Exempt Programs
The Unrated/Exempt Ratings option lets you decide if programs that
the V-Chip recognizes as unrated or exempt can be viewed. Unrated
TV programs may include news, sports, political, religious, local and
weather programs, emergency bulletins, public announcements, and
programs without ratings. The Exempt option applies to both USA and
Canadian unrated programs and Canadian programs rated E.
View All unrated programs are available.
Block All unrated programs are not available.
Note: You must remember to lock Parental controls for rating
limits to take effect.
Press the down arrow button to highlight Unrated/Exempt Ratings.
Then press the right arrow button to toggle between View and Block.
Chapter 3 31
Using the TV’s Features
Future Rating Region
You might notice an option in your Parental control menu that wasn't there before. This is
because broadcasters have the capability to add a new rating system for TV programs. These
ratings let you defi ne additional parameters for parental controls. This option and its name are
dependent on the content acquired from the broadcaster.
Note: These ratings are available only if the broadcaster is sending them.
Additional Features
There are additional features available unrelated to Parental Controls. These features can be
found in other menus.
Picture Processing
With a focus on exceptional picture performance, all RCA models feature Enhanced Natural
Vision (EN-V). EN-V picture processing is designed to provide enhanced color and contrast so
you can enjoy a bright, crisp picture.
Go to page 35 to adjust picture settings.
Screen Formats
Screen format is the way the picture is displayed on your TV. Press the ZOOM +/- button on
your remote to see if a different format is available for the video you are viewing. The format
changes as you press the ZOOM buttons and the format type is displayed at the bottom of the
screen.
Analog video is sent in a 4/3 format, which your TV displays in a 16/9 format. Most digital
video is sent in a 16/9 format which does fi ll your screen, but sometimes is sent in 4/3 which
does not fi ll your screen. It depends on how the station or device connected to your TV is
formatting the video. If there are bars on-screen, press the ZOOM +/- button to try a different
format that may eliminate the bars. Some bars can't be removed because of the way the format
is sent by the broadcaster.
The different formats available and what they look like follow. Each format is available for
analog video, but might not be available for digital video.
4/316/9 zoom
16/9Cinerama
32 Chapter 3
Chapter 4: Using the TV's Menu System
Main Menu
TV
Exit
Channel List
Sound
Picture
Setup
Parental Control
Time
Using the Menu System
This section explores the menus of your TV. Each menu is outlined and
detailed to help you get the most from your TV. The Parental control
menu is discussed in the Features chapter.
To access the menu system:
1. Press the MENU button.
2. Use the up and down arrow buttons to highlight an option and
press OK to display it. The name of the menu is displayed at the
top of the menu screen.
3. Press the up and down arrow buttons to move to a different option
within the menu. If necessary, press the OK button to display the
choices of the option you’ve highlighted. If available, use the text
at the bottom of each screen for help.
4. To return to the Main Menu, press the MENU button until it's
displayed.
Note: Options in the menus that are grayed-out and can't be
highlighted are unavailable or in progress.
Descriptions of each menu are discussed in the order they appear.
There are two ways to exit a menu:
• Press the CLEAR button. The menus are cleared from the screen and
you return to TV viewing.
• Press the MENU button repeatedly until the menus disappear.
The Channel List menu allows you to view all the channels available
in your channel list. Press the up or down arrow button to highlight a
channel then press OK to tune to the channel and exit the menu.
Sound Menu
The Sound menu lets you adjust audio output. To access the Sound
menu, press MENU on the remote, and then select Sound from the
Main Menu. The following audio items can be adjusted:
Equalizer The fi ve-band graphic equalizer lets you adjust the audio
frequency settings. You can select one of the fi ve-band Equalizer
Presets or create your own personal preset.
Sound Preset Allows you to choose a specifi c sound preset.
Press the right arrow to cycle through the options: Standard,
Movie, Voice, Music and Personal.
Frequency Range Displays the different graphic equalizer
bands set for each Sound preset option. Choose a band and make
adjustments. When you make adjustments, the Sound preset option
automatically changes to Personal. Press the left or right arrow
button to select the frequency (100Hz, 300Hz, 1kHz, 3kHz, 10kHz)
you want to adjust. Then use the up or down arrow button to
adjust the level. When you're done adjusting the levels, press the
MENU button to exit.
Chapter 4 33
Graphics contained within this publication are for representation only.
Using the TV's Menu System
Equalizer
Go back
Sound Preset Personal...
Frequency Range ...
Sound
Go back
Equalizer ...
Sound Type Stereo...
Sound Mode Normal...
Dynamic Bass Medium
Balance
Auto Volume Level
Internal Speakers
Headphone Settings ...
Advanced Settings ...
To view the frequency range of another Sound Preset option, press
the right or left arrow until no band is selected and Frequency
Range is highlighted. Then press the up arrow to highlight Sound
Preset.
Sound Type Controls the way the sound comes through your
speakers. The options available vary according to the input selected.
Mono (available for regular TV viewing only) Plays the sound in
mono only. Use this setting when receiving broadcasts with weak
stereo signals.
Stereo Splits the incoming stereo audio signal into left and right
channels. Most TV programs and recorded materials have stereo
audio. The word Stereo appears in the channel banner when you
tune to a program that is broadcast in stereo.
Sound Mode Provides special processing through your speakers
(depending on the setting you chose as your Sound Type). The
available audio modes are:
Normal Does not give any special processing, simply provides
the mono or stereo sound provided by the signal you're watching.
Wide (available only for mono signals) “Widens” sound from
mono broadcasts and mono devices connected to your TV for a
fuller, more spacious sound.
Stereo Wide Available only for stereo signals. Gives a surround
effect with more bass.
Restores clarity and presence for better speech
intelligibility and musical realism.
Dynamic Bass Improves bass output. Displays a choice list of
available settings you can adjust: Off, Medium and High.
Balance Adjusts how much audio is sent to the left and right
speakers.
Auto Volume Level Reduces the annoying blasts in volume during
commercial breaks, and also amplifi es softer sounds in program
material. Eliminates the need to constantly adjust the volume.
Internal Speakers Turn on or off the internal speakers. If you have
a device connected to the Audio Output jacks on the back of the TV
and you want to control the sound by the device instead, uncheck the
box.
Headphone Settings Displays a choice list of available settings you
can adjust: Volume, Bass and Treble. The Headphone sound option
allows you to choose Stereo, Mono or Auto. These descriptions are
same as for Sound Type (see above).
Advanced Settings
Second Audio Program (SAP) Plays the program’s audio in a
Advanced settings
Go back
SAP
Audio Output Fixed...
Default Audio Language English...
Current Audio Track English...
Manufactured under license from BBE Sound, Inc.
second language, if one is available. The letters SAP appear in the
channel banner when you tune to a program that is broadcast with
SAP information. SAP audio is broadcast in mono. SAP is also used
to broadcast a program’s audio with descriptions of the video for
the visually impaired.
34 Chapter 4
Using the TV's Menu System
Advanced settings
Go back
SAP
Audio Output Fixed...
Default Audio Language English...
Current Audio Track English...
Audio Output Lets you choose a setting for the FIXED/
VARIABLE AUDIO OUTPUT jacks.
• Variable Provides variable output from the AUDIO
OUTPUT jacks. Use this setting if the TV is not connected to
an audio receiver or amplifi er and the volume is controlled
by the TV.
• Fixed Provides fi xed output from the AUDIO OUTPUT
jacks to a receiver or amplifi er. With the Fixed Output,
the TV’s volume control, graphic equalizer, and mute are
disabled. This output is ideal when connecting to an audio
receiver or amplifi er that has its own remote control for
controlling the volume.
Default Audio Language Choose the language you prefer for
dialog on digital channels. If your preferred language is being
broadcast with a program, then the TV plays it. If not, then the
TV plays the default audio for the program (usually English in
the U.S.). The default digital channel audio language options are
English, Spanish, French, German, Italian, Japanese, Chinese, and
Korean.
Current Audio Track Press the right arrow to choose from the
audio languages available for the program you're watching. The
language you choose becomes your preferred audio language for
all digital channels until you turn the TV off. If the language you
choose here is not being broadcast with a program, then the TV
plays the default audio for the program (usually English in the
U.S.).
Picture
Go back
Picture Preset Sports...
Brightness
Color
Sharpness
Tint
Contrast
Color Warmth Warm...
Advanced Settings ...
Picture Menu
The Picture menu contains menus and controls to confi gure how the
picture looks. The Picture menu options apply to the video for the
main TV and video input selections. All picture options can be applied
to each input- VID1, VID2, CMP1 or CMP2, HDMI1 or HDM2, and
VGA.
Picture Preset (not available on VGA) Displays a choice list that
lets you select one of the preset picture settings: Vibrant, Cinematic, Natural, Sports, or Personal. Choose the setting that is best for your
viewing environment.
Brightness Adjusts the brightness of the picture.
Color Adjusts the richness of the color.
Sharpness (not available on VGA) Adjusts the crispness of the
edges in the picture.
Tint (not available on VGA) Adjusts the balance between the red
and green levels.
Contrast Adjusts the difference between the light and dark areas of
the picture.
Color Warmth Displays a choice list that lets you set one of three
automatic color adjustments: Cool for a more blue palette of picture
colors; Normal; or Warm for a more red palette of picture colors. The
warm setting corresponds to the NTSC standard of 6500 K.
When you change any of these picture settings, the Picture Preset
changes to Personal. Use the left or right arrow button to make
adjustments. To return to the Picture menu, press the up or down
arrow button.
Chapter 4 35
Using the TV's Menu System
Advanced settings
Go back
Film Mode Advanced...
Noise Reduction Off...
Advanced Picture Settings (not available on VGA)
Film Mode (3:2 Pulldown) Automatically detects video sources
that were originally recorded on fi lm (like most movies) and
subsequently converted to a different format (for TV broadcast,
for example). Film mode processes the converted signal so that it
looks as close as possible to the original. Another name for this
process is reverse 3:2 pulldown.
Advanced (recommended) enables the feature only
when the TV detects that movie playback quality could be
improved. Advanced is the default setting.
The Off setting turns off fi lm mode upconversion. Try using
this setting if you think the reverse 3:2 pulldown is causing
distortions in your picture.
Noise Reduction Reduces picture “static” or any type of
interference. This feature is especially useful for providing a clearer
picture in weak analog signal conditions. Press the right arrow
to choose between: Off for no noise reduction; Low for a softer,
smoother picture that retains picture sharpness and detail; Medium
for a slightly softer picture than the Low setting; High for an even
softer, smoother picture than the other settings (the picture detail is
somewhat decreased).
Note: Video noise reduction is available for the CMP1 and
CMP2 inputs only if the signal is 480i.
Setup
Go back
Channel setup ...
List and Labels ...
Autotuning ...
Closed caption ...
Preferences ...
Message ...
List and Labels
Go back
Channel Number 10
In Channel List
Channel Label ABC
Favorite Channel
Setup Menu
The Setup menu lets you confi gure the TV to fi t its surroundings and
your preferences. To access the Setup menu, press MENU on the
remote, and then select Setup from the Main Menu.
Channel Setup
Signal Type Choose the type of signal you have connected to
the ANTENNA/CABLE INPUT.
Auto Channel Search Searches for channels the signal is
receiving. Go to page 14 for more information.
List and Labels Edit the channels in the list or choose labels for
each channel.
Channel Number Use the number buttons on your remote to
enter the channel number.
In Channel List If you've entered a channel you want to add to
the channel list, highlight In Channel List and press the right arrow
to place a check in the check box. If you've entered a channel you
want to delete from the channel list, press the right arrow button
to uncheck the box.
Channel Label Allows you to add a fi ve character label, which
is displayed on-screen when you tune to the channel entered in
the Channel Number option. Press the up or down arrow button
to enter a character. Continue to press the right arrow button to
highlight the next space to add another character.
36 Chapter 4
Using the TV's Menu System
Favorite Channel The channel you entered for Channel
Number can be saved as a favorite channel. You can have up to
6 favorite channels. To access your favorite channels after they've
been set, exit the menu system. Press the PRESETS (down arrow)
button and then highlight CH+/CH- Buttons. Press the right arrow
to choose Favorite Channels. Press the CLEAR button. When you
press the CH+/CH- buttons, only the favorite channels you set will
be available.
Autotuning Go to Chapter 3 for details about the Autotuning
feature.
Setup
Go back
Channel setup ...
List and Labels ...
Autotuning ...
Closed caption ...
Preferences ...
Message ...
Closed caption
Go back
CC Setting On always...
Analog CC Type CC1...
Digital CC Type Service 1...
Digital CC Preset Default...
Digital CC Style ...
Digital CC style
Go back
Digital CC Size Standard...
Digital CC Font Ashley...
Digital CC Opacity Solid...
Digital CC Color White...
Digital CC Back. Opacity Solid...
Digital CC Back. Color Black...
Closed Caption Many programs are encoded with closed-captioning
information, which lets you display the audio portion of a program as
text on the TV screen.
Note: Closed caption settings are not available for HDMI1,
HDMI2, CMP1, or CMP2 inputs. These settings must be set in
the connected device's menu.
Closed captioning is not available on all channels at all times. Only
specifi c programs encoded with closed-captioning information. When
a program is closed captioned, CC is displayed in the channel banner.
See Chapter 3 for more information about the channel banner. The
closed caption options are:
CC Setting Lets you choose the way closed captioning
information appears on the screen.
Off No captioning information displayed.
On Always Captioning information shown always, when
available.
On When Muted Displays captioning information, when
available, whenever the TV’s sound is muted by pressing the
MU TE button. The captioning information is not displayed
when the sound is not muted.
Analog CC Type If available, lets you select the captioning
mode used for displaying captioning information. If you are
unsure of the differences among the modes, you may prefer
to leave the closed captioned mode set to CC1, which displays
complete text of the program in the primary language in your
area.
Digital CC Type If available, lets you select a closed caption
service mode (1-6) for digital channels.
Digital CC Preset If available, lets you select between Default
and Custom options. Custom changes according to what you set
for the options below.
Digital CC Style If available, lets you customize the following
display options:
Digital CC Size Lets you set the size of the digital closed-
caption text. You can choose Standard, Large, or Small.
Chapter 4 37
Using the TV's Menu System
Digital CC style
Go back
Digital CC Size Standard...
Digital CC Font Ashley...
Digital CC Opacity Solid...
Digital CC Color White...
Digital CC Back. Opacity Solid...
Digital CC Back. Color Black...
Preferences
Go back
Ch. Number Display
Language English...
Maximum TV volume
Power Save Mode
Message
Go back
Display
Start Time 6:00PM...
Recurrence 30min...
Stop Time ...
Erase Message ...
Message ...
Digital CC Font Lets you select a character design for the
digital closed-caption text. A font is a complete assortment
of letters, numbers, punctuation marks, etc. in a given
design. You can choose from a variety of fonts (Ashley,
Floridian, etc.).
Digital CC Opacity Lets you set the appearance of the
digital closed-caption text: Solid, Transparent, Translucent, or
Flashing.
Digital CC Color Lets you choose the color of the digital
Digital CC Back. Opacity Lets you set the appearance
of the space behind the digital closed-caption text: Solid,
Transparent, Translucent, or Flashing.
Digital CC Back. Color Lets you choose the color of the
area of the screen behind the digital closed-caption text:
White, Black, Red, Green, Blue, Yellow, Magenta, or Cyan.
Note: These captioning style options only have an effect on
true digital closed captions.
Not all captioning on digital channels is digital captioning—
it depends on what the broadcaster is sending. If the closed
captioning for a program is not digital, the Digital CC style
settings will not have an effect.
Preferences
Ch. Number Display Turn this feature on if you want the
channel number always available when you press the CH+ or
CH- button.
Language Lets you select your preferred language for the
menus: English, Español or Français.
Maximum TV volume This feature is intended to prevent
volume from being turned up too loudly. Set the volume at the
loudest level you'd want to hear. Press and hold OK to hear the
maximum volume you set.
Power Save Mode If no signal is detected from the VGA input
jack for 5 minutes, puts the TV in power save mode.
Message Set a message that appears at the bottom of the TV screen.
Press the CLEAR button to clear the message. If
Display is turned on,
the message appears when the TV is turned back on after being turned
off.
DisplayTurns on or off to display a message on the TV.
Start TimeSet the time you want to display the message. Not
available if the time hasn't been set in the Time menu.
"Monotype" is a trademark of Monotype Imaging, Inc. registered in the U.S. Patent and Trademark Offi ce and may be registered in
certain other jurisdictions.
"iType" is a trademark of Monotype Imaging, Inc. and may be registered in certain other jurisdictions.
"Floridian", "Plate Gothic", and "Screen" are trademarks of The Monotype Corporation and may be registered in certain other
jurisdictions.
"Ashley" is a trademark of The Monotype Corporation Registered in the U.S. Patent and Trademark Offi ce and may be registered in
certain other jurisdictions.
38 Chapter 4
Using the TV's Menu System
Message
Go back
Display
Start Time 6:00PM...
Recurrence 30min...
Stop Time ...
Erase Message ...
Message ...
Time
Go back
Sleep Timer 03:00 Zzz
Auto Time Channel 12 PBS
Enter Time 8:25PM
Wake up Timer Daily...
Wake up Time 8:00AM
Wake up Channel 12
Turn off Timer Once...
Turn off Time 10:00PM
Recurrence Set how often to display the message- 10min- 60
min.
Stop TimeSet the time you want to the message to stop.
Erase MessageClears all lines of text you've entered.
Message Press OK to enter a message.Enter up to 4 lines of
text- 25 characters per line. Press the right arrow button to start
entering text on a line, then press the up and down arrow buttons
to change characters. Press OK when you're done entering text for
a line.
Parental Control Menu
The Parental control menu was explained in Chapter 3. Go to page 28
for more information.
Time Menu
Sleep Timer Lets you set the TV to turn off after a given amount of
time.
Auto Time Channel Choose your PBS station to have the TV set the
time for you. Wait about one minute for the time to be set.
Enter Time If you didn't set the time reference channel, enter the
current time manually. If it is eight o’clock, for example, you must
fi rst enter the number zero, then number eight. Use the OK button to
choose between AM and PM.
Wake up Timer Lets you set the TV to turn itself on.
Note: The Wake up timer is available only when the time has
been set.
Wake up Time Lets you set the time you want the TV to turn itself
on.
Wake up Channel Lets you select a specifi c channel the TV tunes
to when the wake up timer is set.
Turn off Timer Lets you set the TV to turn itself off.
Turn off Time Lets you set the time you want the TV to turn itself
off.
Chapter 4 39
Chapter 5: Other Information
Frequently Asked Questions (FAQs)
What’s the quickest way to view High Defi nition (HD) video?
Connect an off-air antenna to the ANTENNA/CABLE Input to view free local digital channels.
You might need to purchase an antenna. Go to page 6 for more information.
Visit www.antennaweb.org to get help deciding what type of antenna to use to receive the local
digital channels available to you. By entering where you live, this mapping program tells you
what local analog and digital stations are available using a certain antenna.
Are there other ways to view High Defi nition (HD) video?
Besides using an off-air antenna as mentioned above, you can also use a set-top box to receive
digital video. Contact your cable company or satellite provider to purchase digital programming
and have them connect the box for you to ensure you're viewing channels the best way.
How do I tell an analog channel from a digital channel?
Press the INFO button to display the channel banner. Look at the bottom left corner of the
screen. An A is displayed for an analog channel. A D is displayed for a digital channel.
Why are there bars on my screen and can I get rid of them?
Most digital video is sent in a 16/9 format which does fi ll your screen, but sometimes is sent
in 4/3 which does not fi ll your screen. It depends on how the station or device connected to
your TV is formatting the video. If there are bars on-screen, press the ZOOM +/- button to
try a different format that may eliminate the bars. Some bars can't be removed because of the
way the format is sent by the broadcaster. The format changes as you press the ZOOM buttons
and the format type is displayed at the bottom of the screen. For more information on screen
formats, go to page 32.
Why does channel search fi nd a lot of channels, but when I try to tune to them there’s
nothing there?
Some channels are enabled by the cable company that don’t carry programming, such as videoon-demand. When channels are unavailable, your TV’s screen is blank or appears like snow.
You probably want to get rid of these so they no longer appear in your channel list. Remove
these in the Channel List menu. Go to page 36 for more information.
Why does the fi rst channel search take a long time?
If you have both analog and digital channels, the TV is looking for all available channels in the
channel list. If you do have digital channels, the TV is also searching for scrambled channels,
non-scrambled channels, and each sub-channel of that digital channel.
40 Chapter 5
Graphics contained within this publication are for representation only.
Other Information
Troubleshooting
Most problems you encounter with your TV can be corrected by consulting the following troubleshooting list.
TV Problems
TV won’t turn on
• Make sure the TV is plugged in.
• Check the wall receptacle (or extension cord) to make sure it is “live” by plugging in something else.
• The front panel controls may be locked (disabled). Use the remote control to unlock the front panel controls by
selecting the Front Panel Block in the Parental control menu and press OK to uncheck the box.
No picture, no sound but TV is on
• You might be tuned to an input with no device connected to it to view. If you're trying to view a connected device,
press INPUT until the picture from that device appears.
• Maybe the Signal Type option is set incorrectly. Go to page 14 for detailed instructions.
• The channel might be blank — change channels.
• If you’re watching your VCR and it’s connected with coaxial cable to the ANTENNA/CABLE jack, tune the TV to
channel 3 or 4 (whichever channel is selected on the 3/4 switch on the back of your VCR). Also check to make sure
the TV/VCR button on the VCR is in the correct mode (press the TV/VCR button on your VCR).
Sound okay, picture poor
• If you're getting a black and white picture from a device you've connected to your TV, you might have your video
cables connected to the wrong jacks. A yellow Video cable connects to the yellow VIDEO input jack on the side
or back of your TV; three video cables or bundled component video cables (red, blue, and green) connect to the
corresponding COMPONENT INPUT jacks on the back of your TV.
• If you're getting no picture from a device you've connected to your TV, you might have your video cable connected
to the VIDEO OUTPUT jack on the back of your TV. These jacks are used to connect recording devices. A yellow
Video cable connects to the yellow VIDEO input jack on the side or back of your TV.
• Check antenna connections. Make sure all of the cables are fi rmly connected to the jacks.
• Try adjusting sharpness function to improve weak signals. Go to page 35 for more instructions.
No sound, picture okay
• Maybe the sound is muted. Try pressing the volume up button to restore sound.
• If using DVI, S-Video, or Y, PB, PR, remember to also connect the device’s left and right audio output jacks to the
TV’s L and R Audio Input jacks.
• The sound settings may not be set correctly. Go to page 33 for more information.
• The internal speakers might be turned off. Go to page 34 for more information.
Blank screen
• Check your connections. If you used yellow, red, and white cables to connect, make sure they're connected to the
yellow, red, and white VIDEO INPUT jacks on the side or back of the TV, not to the VIDEO OUTPUT jacks on the
back of the TV.
• If you're trying to watch something that's playing on a device connected to the TV (like a DVD), press INPUT until
you get to the correct video input channel.
• Make sure the device connected to the TV is turned on.
• Try another channel.
Chapter 5 41
Other Information
Buttons don’t work
• The front panel controls may be locked (disabled). Use the remote control to unlock the front panel controls by
selecting the Front Panel Block in the Parental control menu and press OK to uncheck the box.
• Unplug the TV for ten minutes and then plug it back in. Turn the TV on and try again.
TV turns off unexpectedly
• Sleep timer may have been activated. Go to page 39 for instructions.
• Electronic protection circuit may have been activated because of a power surge. Wait 30 seconds and then turn on
again. If this happens frequently, the voltage in your house may be abnormally high or low.
• Unplug. Wait ten minutes. Plug in again.
TV turns on unexpectedly
• Wake up timer might have been activated. Go to page 39 for instructions.
Can’t select certain channel
• Channel may be blocked or not approved in the Parental Controls menu.
• If using a VCR, check to make sure the TV/VCR button on the VCR is in the correct mode (press the TV/VCR button
on your VCR).
• Press the TV button and then try to change channels.
Noisy stereo reception
• May be a weak station. Use Sound menu to choose mono sound.
Black box appears on the screen
• Closed-captioning might be on. Check Closed Caption in the Setup menu. Go to page 37 for more instructions.
Problems with HDMI Connection
• Make sure the HDMI or DVI device is turned on and the cables are fi rmly connected. If problems still occur, turn off
your device. Re-connect your device. Reset the power by unplugging the power cord and plugging it back in.
• If you are tuned to the HDMI 1 or 2 input and you’re receiving Unusable Signal message on-screen, press the
INFO button on the remote. If Acquiring Channel appears in the channel banner, the HDMI or DVI device isn’t
responding. Contact the manufacturer of the HDMI or DVI device for further assistance.
• If you tune to the HDMI 1 or 2 input and you see snow, the video goes in and out, or the video takes a long time
to appear, your HDMI or DVI device is having trouble sending video information to the TV. Re-connect your device.
Reset the power by unplugging the power cord and plugging it back in. If problems persist, try connecting the
Y Pb Pr jacks instead if they are available or contact the manufacturer of the HDMI or DVI device for further
assistance.
• If you have black bars on each side of your picture, the device you connected might have a switch or a menu
option allowing you to change the picture quality output that will fi x this. Choose either 720p or 1080i.
• 480i signals aren’t supported by the HDMI1/DVI or HDMI2 input.
The Remote Control Doesn’t Work
• Something might be between the remote and the remote light sensor on the front of the TV. Make sure there is a
clear path.
• Maybe the remote isn’t aimed directly at the TV.
• Maybe batteries in remote are weak, dead, or installed incorrectly. Put new batteries in the remote. (Note, if you
remove the batteries, you may have to reprogram the remote to operate other devices.)
42 Chapter 5
Other Information
Problems with V-Chip/Parental Controls
The rating limits don’t work
• You must lock the settings. Go to the Main Menu (press MENU on your remote), select Parental control, select Lock
Parental Controls.
I don’t remember my password and I want to unlock the TV
• If you forget your password, turn the TV off. Simultaneously press and hold VOL v on the side panel and CLEAR on
the remote for 10 seconds. Next time you enter the Parental control menu enter a new password
The V-Chip won’t let me watch a program even though it’s not rated as violent.
• Maybe the movie was given an NR (Not Rated) status. After you block movie ratings, you must set NR to View
separately in order to view movies with an NR rating.
What Else Can I Do?
If you’ve been through the Troubleshooting section and nothing has fi xed your problem, try rebooting your TV. Note
that after a reboot you may need to run your TV through the setup process again. To do a reboot, unplug the power
cord from the wall outlet, power strip, etc. Keep your TV unplugged for about 5 minutes. Then plug the TV back in,
turn on the TV, and see if the problem is fi xed. If the problem remains, then please visit www.rca.com/television for
updated FAQs or contact RCA Customer Support at the support number provided in your Warranty under How To Get
Service.
Bottom of the base
Remove the screws from the four holes on
each side of the bottom of the TV’s base.
Mounting Your TV to the Wall
Caution: The wall mount must bear a minimum of fi ve times
the TV’s net weight without causing damage.
To mount your TV to the wall you need to purchase a VESA wall
mount. For models L37WD22 and L42WD22, purchase a VESA 400 x
400, M6 x 10mm; and model L46WD22 purchase a VESA 600 x 400, M6
x 10mm (400 x 400, for example, means the mounting measurements
are 400mm horizontally and 400mm vertically; M6 x 10mm is the type
screw that needs to be used).
1. You need to remove the base fi rst before attaching the wall mount.
A. Place the TV facedown on a surface that is soft, yet strong
enough to hold the TV.
B. Use a screwdriver to remove the screws from the four holes on
each side of the bottom of the TV’s base as the arrows indicate
to the left.
2. Make sure all cables are already connected to the TV.
3. Follow the directions included with the wall mount to mount the
TV to the wall.
Chapter 5 43
Other Information
V-Chip Rating Explanations
US V-Chip Rating System
TV-MA (Mature Audience Only) Specifi cally designed to be viewed by adults and may be unsuitable for children
under 17. It contains one or more of the following content themes: crude indecent language (L), explicit sexual activity
(S), or graphic violence (V).
TV-14 (Parents Strongly Cautioned) Contains some material that many parents would fi nd unsuitable for children
under 14. Parents are strongly urged to exercise greater care in monitoring this program and are cautioned against
letting children under the age of 14 watch unattended. This program contains one or more of the following content
themes: intensely suggestive dialogue (D), strong coarse language (L), intense sexual situations (S), or intense violence
(V).
TV-PG (Parental Guidance Suggested) Contains material that parents may fi nd unsuitable for younger children. Many
parents may want to watch it with their younger children. The program contains one or more of the following content
themes: some suggestive dialogue (D), infrequent coarse language (L), some sexual situations (S), or moderate violence
(V).
TV-G (General Audience) Most parents would fi nd this program suitable for all ages. It contains little or no sexual
dialogue (D) or situations (S), no strong language (L), and little or no violence (V).
TV-Y7 (Directed to Children 7 years and older) Designed for children ages 7 and above. It may be more appropriate
for children who have acquired the developmental skills needed to distinguish between make-believe and reality.
Themes and elements in this program may include mild fantasy violence (FV) or comedic violence, or may frighten
children under the age of 7.
TV-Y (All Children) Themes and elements in this program are designed for a young audience, including children from
ages 2-6. It is not expected to frighten younger children.
Canadian English V-Chip Rating System
18+ (Adults) Programming intended for adults 18 and older. It may contain elements of violence, language, and sexual
content which could make it unsuitable for viewers under 18. Violence Guidelines: May contain violence integral to
the development of the plot, character or theme, intended for adult audiences. Other Content Guidelines: May contain
graphic language and explicit portrayals of nudity and/or sex.
14+ (Viewers 14 and over) Programming contains themes or content which may not be suitable for viewers under
the age of 14. Parents are strongly cautioned to exercise discretion in permitting viewing by pre-teens and early teens.
Violence Guidelines: May contain intense scenes of violence. Could deal with mature themes and societal issues in a
realistic fashion. Other Content Guidelines: May contain scenes of nudity and/or sexual activity. There could be frequent
use of profanity.
PG (Parental Guidance) Programming intended for a general audience but which may not be suitable for younger
children (under the age of 8). Parents may consider some content inappropriate for unsupervised viewing by children
aged 8-13. Violence Guidelines: Depictions of confl ict and/or aggression will be limited and moderate; may include
physical, fantasy, or supernatural violence. Other Content Guidelines: May contain infrequent mild profanity, or mildly
suggestive language. Could also contain brief scenes of nudity.
G (General Audience) Programming considered acceptable for all ages groups. While not designed specifi cally for
children, it is understood younger viewers may be part of the audience. Violence Guidelines: Will contain very little
violence, either physical or verbal or emotional. Will be sensitive to themes which could frighten a younger child, will
not depict realistic scenes of violence which minimize or gloss over the effects of violent acts. Other Content Guidelines:
There may be some inoffensive slang, no profanity and no nudity.
44 Chapter 5
Other Information
C8+ (Children 8 and Older) Programming generally considered acceptable for children 8 years and over to watch
on their own. Violence Guidelines: Violence will not be portrayed as the preferred, acceptable, or only way to resolve
confl ict or encourage children to imitate dangerous acts which they may see on television. Any realistic depictions
of violence will be infrequent, discreet, of low intensity and will show the consequences of the acts. Other Content
Guidelines: There will be no profanity, nudity or sexual content.
C (Children) Programming intended for children under age 8. Violence Guidelines: Careful attention is paid to
themes which could threaten children’s sense of security and well being. There will be no realistic scenes of violence.
Depictions of aggressive behaviour will be infrequent and limited to portrayals that are clearly imaginary, comedic or
unrealistic in nature. Other Content Guidelines: There will be no offensive language, nudity or sexual content.
Canadian French V-Chip Rating System
18+ (Adults) Programming is for adults only. This program contains sustained violence or extremely violent scenes.
16+ (Viewers 16 and over) Programming is not suitable for those under age 16. This program contains frequent scenes
of violence or intensely violent scenes.
13+ (Viewers 13 and over) Programming may not be suitable for children under the age of 13. This program either
contains several violent scenes or one or more scenes that are violent enough to affect them. Viewing in the company
of an adult is therefore strongly recommended for children under the age of 13.
8+ (Viewers 8 and over) Not recommended for young children. This program is suitable for most audiences, but it
contains mild or occasional violence that could upset young children. Viewing in the company of an adult is therefore
recommended for young children (under the age of 8) who do not distinguish between reality and imagination.
G (General Audience) This program is suitable for audiences of all ages. It contains no violence, or any violence that it
does contain is either minimal or is presented in a humorous manner, as a caricature, or in an unrealistic way.
Chapter 5 45
Other Information
Limited Warranty
What your warranty covers:
• Defects in materials or workmanship to the fi rst consumer purchaser.
For how long after your purchase:
• 90 days from date of purchase for labor charges for screen sizes 32” and smaller. One year from date of purchase
for labor charges for screen sizes larger than 32”. At our option, we will either pay an Authorized RCA Service
Center the labor to repair your television or replace your television with a new or refurbished unit.
• One year from date of purchase for parts. At our option, we will either supply new or refurbished parts to
an Authorized RCA Service Center for them to repair your television or replace your television with a new or
refurbished unit. After 90 days, labor charges will be at your expense for screen sizes 32” and smaller.
How you get service:
• Call 1-800-951-9582 or visit www.rca.com. Please have your unit’s date of purchase and model/serial number ready.
The model/serial number information can be found on the back of your unit.
• Proof of purchase in the form of a bill of sale or receipted invoice which is evidence that the product is within the
warranty period must be presented to obtain warranty service. For rental fi rms, proof of fi rst rental is also required.
What your warranty does not cover:
• Customer instruction. (Your Owner’s Manual describes how to install, adjust, and operate your television. Any
additional information should be obtained from your dealer).
• Installation and related adjustments.
• Signal reception problems not caused by your television.
• Damage from misuse or neglect.
• Batteries.
• Customer replacement fuses.
• Damage from images burnt onto the screen.
• Special, incidental or consequential damages.
• A television that has been modifi ed or incorporated into other products or is used for institutional or other
commercial purposes.
• A television purchased or serviced outside the U.S.A.
• Acts of nature, such as but not limited to lightning damage.
Product registration:
• Please complete and mail the Product Registration Card packed with your TV or register on-line at
www.rca.com/television. It will make it easier to contact you should it ever be necessary. The return of the card is
not required for warranty coverage.
Limitation of Warranty:
• THE WARRANTY STATED ABOVE IS THE ONLY WARRANTY APPLICABLE TO THIS PRODUCT.
NO VERBAL OR WRITTEN INFORMATION GIVEN BY TTE TECHNOLOGY, INC., ITS AGENTS OR
EMPLOYEES SHALL CREATE A GUARANTY OR IN ANY WAY INCREASE THE SCOPE OF THIS
WARRANTY.
46 Chapter 5
Other Information
• REPAIR OR REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS THE EXCLUSIVE REMEDY
OF THE CONSUMER. TTE TECHNOLOGY, INC. SHALL NOT BE LIABLE FOR SPECIAL, INCIDENTAL
OR CONSEQUENTIAL DAMAGES RESULTING FROM THE USE OF THIS PRODUCT OR ARISING
OUT OF ANY BREACH OF ANY EXPRESS OR IMPLIED WARRANTY ON THIS PRODUCT. THIS
DISCLAIMER OF WARRANTIES AND LIMITED WARRANTY ARE GOVERNED BY THE LAWS OF
THE STATE OF INDIANA. EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW, ANY
IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ON THIS
PRODUCT IS LIMITED TO THE APPLICABLE WARRANTY PERIOD SET FORTH ABOVE.
How state law relates to warranty:
• Some states do not allow the exclusion nor limitation of incidental or consequential damages, or limitations on how
long an implied warranty lasts, so the above limitations or exclusions may not apply to you.
• This warranty gives you specifi c legal rights, and you also may have other rights that vary from state to state.
If you purchased your product outside the United States:
• This warranty does not apply. See your dealer for warranty information.
Service calls which do not involve defective materials or workmanship are not covered by this
warranty. Costs of such service calls are the sole responsibility of the purchaser.
Care and Cleaning
CAUTION: Turn OFF your TV before cleaning.
You can clean the TV as required, using a soft lint-free cloth. Be sure to occasionally dust the ventilation slots in the
cabinet to help assure adequate ventilation.
IMPORTANT: Never use strong cleaning agents, such as ammonia-based cleaners, or abrasive
powder. These types of cleaners will damage the TV.
The TV’s screen may be cleaned with a soft, lint-free cloth as well. Take care not to scratch or mar
the screen. If necessary, you may use a cloth dampened with warm water.
liquid directly on the screen, or allow liquid to run down the screen and inside the TV. Also, never place drinks or vases
with water on top of the TV. This could increase the risk of fi re or shock hazard or damage to the TV.
While cleaning do not spray
Chapter 5 47
ENERGY STAR and the ENERGY STAR mark are registered U.S. marks
Manufactured under license from Dolby Laboratories.
Dolby and the double-D symbol are trademarks of Dolby Laboratories.
FCC Information
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used
in accordance with the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged
to try to correct the interference by one or more of the following measures:
· Reorient or relocate the receiving antenna.
· Increase the separation between the equipment and receiver.
· Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
· Consult the dealer or an experienced radio/TV technician for help.
This Class B digital apparatus complies with Canadian ICES-003.
Visit the RCA website at www.rca.com/television
Please do not send any products to the Indianapolis address listed in this manual or on the carton. This will only
add delays in service for your product.