RCA HD61LPW52 User Manual

High-Definition

Television

User’s Guide

Changing Entertainment. Again.

Important Information

WARNING

To reduce the risk of fire or
electric shock, do not expose
this product to rain or moisture.
The apparatus shall not be
exposed to dripping or

splashing and no objects filled
with liquids, such as vases, shall
be placed on the apparatus.

Refer to the identification/rating label located on the back panel of your product for its proper operating voltage.
FCC Regulations state that unauthorized changes or modifications to this equipment may void the user’s authority

to operate it.
Cable TV Installer: This reminder is provided to call your attention to Article 820-40 of the National Electrical

Code (Section 54 of the Canadian Electrical Code, Part 1) which provides guidelines for proper grounding and, in
particular, specifies that the cable ground shall be connected to the grounding system of the building as close to
the point of cable entry as practical.

Important: This television is a table model and is designed to sit on a firm, flat, surface. Don't place the TV on soft
carpeting or similar surface because the ventilation slots on the bottom of the unit will be blocked resulting in
reduced lifetime from overheating. To assure adequate ventilation for this product, maintain a spacing of 4 inches
from the top and sides of the TV receiver and 2 inches from the rear of the TV receiver and other surfaces. Also,
make sure the stand or base you use is of adequate size and strength to prevent the TV from being accidentally
tipped over, pushed off, or pulled off. This could cause personal injury and/or damage the TV. Refer to the
Important Safety Instructions packed separately.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

This symbol indicates
"dangerous voltage" inside
the product that presents a
risk of electric shock or
personal injury.

This symbol indicates that the lamp in the HDTV contains mercury.
Disposal of these materials may be regulated due to environmental
considerations. For disposal or recycling information, please contact
your local authorities or the Electronic Industries Alliance:
www.eiae.org.

Caution: To reduce the risk of electric shock, do
not remove cover (or back). No user serviceable
parts inside. Refer servicing to qualified service
personnel.

This symbol indicates
important instructions
accompanying the product.

Product Registration

Please fill out the product registration card (packed separately) and return it immediately. For U.S. customers: Your
RCA Consumer Electronics product may also be registered at www.rca.com/productregistration. Returning the card
allows us to contact you if needed.

Product Information

Keep your sales receipt to obtain warranty parts and service and for proof of purchase. Attach it here and record
the serial and model numbers in case you need them. These numbers are located on the product.

Model No. ______________________________________________________________________________________________

Serial No ._______________________________________________________________________________________________

Purchase Date: __________________________________________________________________________________________

Dealer/Address/Phone: ___________________________________________________________________________________

Introduction

Thank you for choosing RCA

Congratulations on purchasing this RCA High Definition Television (HDTV) featuring Digital
Light Processing™ (DLP™) technology—a true viewing experience. Your purchase decision
represents an investment in a new generation of technology— DLP and HDTV. Even though
this is a technologically advanced HDTV, it is the most user-friendly of its kind— with
comprehensive on-screen instructions that guide you through all of the TV’s features.

This introduction has three parts that describe why an RCA HDTV featuring DLP technology is
an excellent choice:

Part 1: DLP—brilliance in color, design, and technology
Part 2: Why RCA DLP is better
Part 3: Other Key Features of owning an RCA HDTV

Part 1: DLP— brilliance, in color, design, and technology

RCA brings you brilliant pictures with Digital Light Processing (DLP) system — a brilliantly
choreographed, engineering marvel that combines microscopic mirrors, light, and color to bring
you the best and brightest pictures possible.

Service Model Number Numéro de Modéle-Service

HDLP50XXXXXX
000000000 X

SERIAL SERIE LAMP

EXAMPLE: Service Model Number sticker
with lamp type listed.

Model No.____________________________________

Lamp Type___________________________________

Date_________________________________________

How DLP Works

In general, DLP combines microscopic mirrors, a specially
designed semiconductor, and a color wheel to adjust light to
display the most brilliant, accurate images! Your DLP HDTV
doesn’t use Cathode Ray Tubes (CRTs), which means you don’t
have to worry about screen burn (fixed video images burning
onto the screen permanently) or convergence (realigning the
CRTs). The diagram on the left illustrates the complex system.

Thin and Light

The efficiency of DLP technology enabled our design team to
create a high-performance HDTV that is about 16 inches thin and
weighs less than 100 pounds.

Lamp Replacement

DLP technology uses a special lamp. Eventually, you’ll need to
replace this lamp, which you can do yourself by following the
replacement instructions on page 67. To order the correct lamp,
you’ll need to know your TV’s model number, serial number, and
lamp type—this information is listed on the Service Model
Number sticker (example of the sticker is shown on the left). The
sticker is located on the right side of the TV. The lamp type can
also be found in the TV’s Lamp Power menu. Go to page 62 for
more information. For future reference, write down the
information in the space provided at the left.

Digital Light Processing, DLP and DLP Cinema are trademarks of Texas Instruments. All other products and names may or may not be
trademarks or registered trademarks of their respective companies.

1

Introduction

Part 2: Why RCA DLP is better

DLP is just part of the story. You have chosen to embark on the next generation of TV viewing— HDTV. There are many
technological advancements that make HDTV better than analog TV, but there are basically three things about HDTV that
bring you a superior viewing experience: (1) resolution, (2) aspect ratio, and (3) digital signal and sound.

Resolution (it’s math...that works for you)

The crisp, lifelike picture that people rave about when experiencing true HDTV is due to the resolution this technology
provides. The resolution is measured by calculating the number of active lines of pixels. A pixel (which stands for picture
element) is a small dot. The picture you see on your TV is composed of these dots.

A regular, analog television only has a resolution of about 200,000 pixels (480 vertical pixels x 440 horizontal pixels =
211,200 pixels). The HDTV format is capable of more than 2 million pixels (1,920 x 1,080 = 2,073,600).

More pixels equal more detail. In summary, HDTV is capable of resolution that is up to 10 times the resolution of the
picture on a regular, analog TV!

Feature Analog (NTSC) HD Digital (ATSC)

Total Scan Lines 525 1125

Effective Scan Lines 480 1080

Aspect Ratio 4:3 16:9 (Widescreen)

Max Resolution 720 x 480 1920 x 1080

Sound 2-ch Stereo 5.1 ch Surround

16:9 Aspect Ratio

4:3 Aspect Ratio

Aspect Ratio

Aspect ratio is simply the width and height of the picture. Regular TVs use a
4:3 aspect ratio, which means the picture is a little wider than it is tall (a
screen that is 20 inches wide is about 15 inches tall).

When the standards were being developed for television broadcasting in
1941 by the NTSC (the National Television Standards Committee), it made
sense to adopt the 4:3 aspect ratio the film industry was using at that time.

As TVs dropped in price and people prospered in the 1950s, the movie
industry had to find a way to get people out of their living rooms and back
to the movie theatres. That’s when they created the 16:9 aspect ratio (also
called widescreen format). When the standards for HDTV were being
developed by the ATSC (Advanced Television Standards Committee), the 16:9
aspect ratio was chosen as the format for HDTV.

This widescreen format makes sense because it’s much closer to the way we
see. Our field of vision is actually much wider than tall because of our
peripheral vision. Not only is it closer to the way we see, but the pictures are
crisper and cleaner with more detail in the close-up and panoramic views.

2

Introduction

Digital Signal and Sound

The analog television broadcast system that has been used in the United States for the past 50 years transmits signals as
electronic waves. These waves can suffer degradation as the signal travels to your home. Additionally, the analog waves are
susceptible to interference from planes passing overhead, weather, and household appliances.

Digital signals, in contrast to analog signals, can be reproduced precisely because the images are transmitted and received
using the computer language of 1s and 0s. Such precision yields a signal that is capable of displaying studio-quality picture
and Dolby Digital 5.1 channel sound.

Part 3: Other Key Features of owning an RCA HDTV

There are other HDTV’s on the market- even some that use DLP technology. But your RCA HDTV has been designed with
features that will enhance your TV viewing experience, and features that provide flexibility to build on the digital revolution
that is taking place. A summary of your TV’s most unique features follows. Go to Chapter 3 for more details on these and
additional features.

Integrated HDTV Tuner with Digital Cable Ready QAM

RCA was the first to offer an integrated tuner with its HDTVs (which means there is no need for another box to receive
digital programming). Now, we’ve gone one better— your HDTV’s tuner is digital cable ready (no need for a cable box to
view unscrambled digital cable programming). The CableCARD™ slot on your HDTV allows you to use a digital cable card
to access digital cable. The tuner is able to decode all 35 formats of digital television broadcasts, and it can interpret
unscrambled digital cable signals because it includes QAM (Quadrature Amplitude Modulation).

Note: A digital cable card may be necessary to view scrambled (encrypted) channels. Contact your cable provider for
more information. Go to page 18 for more information.

TruScan Digital Reality

The intelligent signal processing of TruScan Digital Reality recognizes incoming video signals and progressively converts
them to achieve optimum digital picture performance. It also recognizes when original film sources have been modified and
can automatically convert the analog frame rate back to its original format to bring out the detail--a process commonly
referred to as reverse 3:2 pulldown.

User-friendly Features Help You Personalize Your TV

•You can customize your TV to fit your viewing taste and match the lighting
where you watch TV by using Personal Presets and/or the automatic picture
quality settings: Vibrant (Day), Natural, Cinematic (Night), Videogame,
Professional. You can adjust each input to a different setting and the TV will
automatically adjust the picture when you change inputs.

• Help Text: The elaborate, on-screen help text describes your TV’s features
and explains how to use them.

Go Back

0

Picture Settings

1

Picture PresetsPicture Presets

2

Auto Color

3

Color Warmth

4

Noise Reduction

5

Green Stretch

6

Edge Enhancement

7

Contrast Expand

8

Advanced Settings

9

Main Menu Picture Quality

Vibrant (Day)

Natural

Cinematic (Night)

Videogame

Professional

Personal

A change in this screen is applied to Input 3.

Press  or  to point to an option, then press OK to select it.
Press to return to the menu.

Contrast
Color
Tint
Black Level
Sharpness
Auto Color
Color Warmth
Noise Reduction
Green Stretch
Edge Enhancement
Contrast Expand

Frame Comb

Help text

65%
70%
55%
60%
55%

On

Cool

High

Low

High

CableCARD is a registered trademark of Cable Television Laboratories, Inc.

3

Introduction

Audio System

Enjoy the great sound system in your HDTV with 20 watts total power. A 7-band on-screen
graphic equalizer allows customization of the sound quality.

You can take advantage of the 6-Channel direct Audio Outputs (Matrix Surround, Subwoofer,
etc.) if you have an amplifier you want to connect to your HDTV. Then choose to control the
volume from the TV or the amplifier in the Fixed/Variable Output option in the Audio
Connections menu. If you own an amplifier with digital audio, connect to the DIGITAL AUDIO
OUTPUT jack instead.

Audio/Video Output Jacks

Because the VCRs in most households are analog and can’t receive or record digital TV signals,
recording digital TV broadcasts wasn’t possible without purchasing additional equipment. That’s
why RCA added AUDIO/VIDEO OUTPUT jacks to this HDTV. These jacks enable you to record
both analog and digital programs. RCA understands how you watch TV and what’s necessary to
make the transition to HDTV seamless.

4

Table of Contents

Introduction .............................................................................................. 1

Chapter 1: Connections & Setup

Things to Consider Before You Connect ........................................................................................ 8

Protect Against Power Surges.................................................................................................. 8

Protect Components from Overheating.................................................................................. 8

Position Cables Properly to Avoid Audio Interference........................................................... 8

Use Indirect Light...................................................................................................................... 8

Using a Stand ............................................................................................................................ 8

Cables You May Need to Connect Components to Your TV .................................................. 8

Choose Your Connection ................................................................................................................. 9

Explanation of Jacks and Cables .................................................................................................. 10

The Front of Your TV ..................................................................................................................... 14

Front Input Jacks..................................................................................................................... 14

Front Panel .............................................................................................................................. 14

How to Connect: TV + VCR + DVD Player ............................................................................. 15

How to Connect: TV + Satellite Receiver + VCR .................................................................... 16

How to Connect: TV + Component with DVI or HDMI......................................................... 17

How to Connect: TV + CableCARD ........................................................................................ 18

Setting Up Digital Cable Television Service........................................................................... 18

Audio Connections ................................................................................................................. 19

Plug in the TV................................................................................................................................. 21

Put Batteries in the Remote .......................................................................................................... 21

Turn on the TV ............................................................................................................................... 21

Use the Remote Control to Complete the Assisted Setup.......................................................... 21

Complete the Assisted Setup........................................................................................................ 21

Set the Menu Language ......................................................................................................... 22

Complete Channel Search ...................................................................................................... 22

Changing Channels................................................................................................................. 22

Next Steps ...................................................................................................................................... 22

Chapter 2: Using the Remote Control

The Buttons on the Remote Control ............................................................................................ 24

Programming the Remote to Operate Other Components ........................................................ 26

Find Out If You Need to Program the Remote ..................................................................... 26

Programming the Remote ..................................................................................................... 26

How to Use the Remote After You’ve Programmed It ............................................................... 27

The Learning Feature .................................................................................................................... 28

Adding a Learned Function ................................................................................................... 28

Clearing a Learned Function .................................................................................................. 29

Deleting ALL Learned Functions ............................................................................................ 29

Volume Punchthrough Feature .....................................................................................................30

Deleting ALL Volume Punchthrough Commands ................................................................. 30

Using the INPUT Button ................................................................................................................ 31

Remote Code List ........................................................................................................................... 31

Chapter 3: Using the TV’s Features

About the Channel Banner ........................................................................................................... 34

Digital or Analog TV Channels ..................................................................................................... 35

Direct Tuning to a Channel .................................................................................................... 35

Parental Controls ........................................................................................................................... 36

Lock/Unlock TV ....................................................................................................................... 36

Channel Lists (Video Input List, Cable Channel List, Antenna Ch. List) ............................... 36

5

Table of Contents

How V-Chip Works for the USA and Canada ............................................................................... 37

USA V-Chip TV Ratings ...........................................................................................................37

Canada V-Chip ........................................................................................................................ 41

Auto Tuning Feature...................................................................................................................... 43

PIP (Picture-in-Picture) Operation ................................................................................................. 44

Emergency Alert System (EAS) ..................................................................................................... 46

Chapter 4: Using the TV’s Menu System

Menus, On-screen Help, and Control Panels ............................................................................... 48

Navigating the Menu System................................................................................................. 48

On-Screen Help ....................................................................................................................... 48

Controls ................................................................................................................................... 48

Picture Quality Menu .................................................................................................................... 50

Picture Settings ....................................................................................................................... 50

Picture Presets ......................................................................................................................... 50

Auto Color............................................................................................................................... 51

Color Warmth ......................................................................................................................... 51

Noise Reduction ...................................................................................................................... 51

Green Stretch .......................................................................................................................... 51

Edge Enhancement................................................................................................................. 51

Contrast Expand ..................................................................................................................... 52

Advanced Settings .................................................................................................................. 52

Audio Menu ................................................................................................................................... 53

Equalizer Presets ..................................................................................................................... 53

Audio Processor ...................................................................................................................... 53

Sound Logic............................................................................................................................. 54

Audio Mode ............................................................................................................................ 54

SAP (Second Audio Program)................................................................................................. 54

Balance .................................................................................................................................... 54

Audio Connections ................................................................................................................. 55

Connections Menu......................................................................................................................... 56

Signal Strength ....................................................................................................................... 56

Channel Search ....................................................................................................................... 56

Software Upgrade .................................................................................................................. 57

Signal Source........................................................................................................................... 57

Video Input Setup................................................................................................................... 57

Auto Tuning ............................................................................................................................ 57

Special Features ...................................................................................................................... 58

Ethernet Setup ........................................................................................................................ 59

Preferences Menu .......................................................................................................................... 59

Closed Captioning .................................................................................................................. 59

Screen Format ......................................................................................................................... 61

Time Menu .............................................................................................................................. 62

Color Scheme .......................................................................................................................... 62

Translucency ............................................................................................................................ 62

Menu Language...................................................................................................................... 62

Lamp Power ............................................................................................................................ 62

Chapter 5: Reference

Troubleshooting ............................................................................................................................. 64

Lamp Replacement Instructions ...................................................................................................67

HDTV Specifications ...................................................................................................................... 70

Accessory Information .................................................................................................................. 72

Limited Warranty........................................................................................................................... 73

Care and Cleaning ......................................................................................................................... 74

FCC Information ............................................................................................................................. 74

6

Chapter 1

Connections & Setup

Chapter Overview:

• Things to Consider Before You Connect

• Choose Your Connection

• Explanation of Jacks and Cables

• The Front of Your TV

• How To Connect

• Plug in the TV

• Put Batteries in the Remote

•Turn on the TV

• Use the Remote Control to Complete
the Assisted Setup

• Complete the Assisted Setup

• Next Steps

Changing Entertainment. Again.

Graphics contained within this publication are for representation only. 7

Connections & Setup

Things to Consider Before You Connect

Protect Against Power Surges

• Connect all components before you plug any of their power cords into the wall outlet or
power strip. NEVER plug your TV into an outlet that is controlled by a wall switch.

•Turn off the TV and/or component(s) before you connect or disconnect any cables.

• Make sure all antennas and cables are properly grounded. Refer to the Important Safety
Instructions packed with your TV.

Protect Components from Overheating

• Don’t block ventilation holes on any of the components. Arrange the components so that air
can circulate freely.

• Don’t stack components.

• If you place components in a stand, make sure you allow adequate ventilation.

• If you connect an audio receiver or amplifier, place it on the top shelf so the heated air from it
won’t flow around other components.

Position Cables Properly to Avoid Audio Interference

• Insert each cable firmly into the designated jack.

Use Indirect Light

Don’t place the TV where sunlight or room lighting will be directed toward the screen. Use soft or
indirect lighting.

Using a Stand

If a stand, base, or cabinet is used, insure that it is of adequate size and strength to prevent the TV
from being accidentally tipped over, pushed off, or pulled off. This could cause personal injury
and/or damage the TV. Refer to the Important Safety Instructions packed with your TV.

Cables You May Need to Connect Components to Your TV

The pictures below show the cables (not supplied) you may need for the connections represented
in this book.

S-Video cable

CAT5 (Ethernet) cable

Audio cables

Composite
Audio/ Video cables

Component Video
(Y, Pb, Pr) cable

Coaxial cable

HDMI and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC.

Digital Optical cable

Speaker Wire

HDMI™ cable (or DVI
cable and HDMI/DVI
adapter)

8 Chapter 1

Connections & Setup

Choose Your Connection

There are several ways to connect your HDTV, depending on the components you want to connect and the quality of the
signal you want to achieve. Please use the following chart to determine which connection is best for you. Proceed to the
appropriate page and connect your TV. For more information about the relationship between the cables, jacks, and the
quality of the signal you see on your TV, go to the following page.

Note for U.S. Customers: If you prefer, we can provide you with the name of an Authorized Service Representative
who will visit your home for a fee to install your electronic entertainment system and to instruct you in its operation.
For details about this service, call 1-888-206-3359. For additional assistance while using your RCA product, please
visit

www.rca.com/customersupport.

Components Cables Needed Connection Title Go to...

Video Connections

TV

Coaxial

WER

O
P
+
OL

V
—
VOL

CH
H

C
NU
E
M

DVD

VCR

Audio
Component
Composite

TV + VCR + DVD
Player

page 15

R
E
W
PO

+
VOL

—
VOL
CH

H
C

MENU

TV

VCR

Satellite Receiver

Digital/Network Connections

ER
W
O
P

+
L
VO
—

L
O
V

CH

CH
ENU
M

TV

Component with

DVI or HDMI

POWER

+
VOL
—

L
VO

CH

CH
U
N
ME

CableCARD

TV

Audio Connections

ER

W
PO
+
L
O
V
—

OL
V

H
C

CH
U
MEN

TV

A/V

Receiver

Speakers

Coaxial
Audio

TV + Satellite
Receiver + VCR

Composite
S-Video

TV + Component

HDMI (or DVI with

with DVI or HDMI

HDMI/DVI adapter)

Coaxial TV + CableCARD

Coaxial

Optical cable or
Audio cables

TV + A/V Receiver +
Speakers
or
TV + Receiver w/

Speaker wire

Dolby Digital +
Speakers

page 16

page 17Coaxial

page 18

pages 19,
20

Chapter 1 9

Connections & Setup

Explanation of Jacks and Cables

The diagrams below illustrate jacks found on the back of the TV. When connecting cables, be sure
to connect corresponding outputs and inputs (video input into video out, right audio input into
right audio out, etc.).

This section describes the jacks and cables you might use to make connections (cables may be
ordered separately by calling the number on page 72). There are several ways to connect
components to your TV.

Different jacks and cables provide a different level of performance. It’s important to remember the
different degrees of picture quality for comparison. The HDMI/DVI and component jacks are
considered excellent; S-Video is very good; composite jacks are good, while connecting
components to the Antenna or Cable Input is fair.

TV

CENTER SPEAKER INPUT

EXTERNAL AMP

MAX POWER RATING!

(60 WATTS into 8 OHMS)

POWER
(AC 120V~60Hz)

DIGITAL

AUDIO

ETHERNET

OUTPUT

CENTER SPEAKER INPUT

EXTERNAL AMP

MAX POWER RATING!

(60 WATTS into 8 OHMS)

FIXED/VARIABLE AUDIO OUTPUTS

CENTER

R REAR

FIXED/VARIABLE AUDIO OUTPUTS

CENTER

SUBWOOFER

R REAR

R

L REAR

L REAR

MATRIX

SURROUND

OUTPUTS

L

MATRIX

SURROUND

OUTPUTS

WIRED

IR

CableCARD™

COMPOSITE INPUTS

INPUT 3

L

L

INPUT 1

V

V

CABLE

INPUT

S-VIDEO

S-VIDEO

R

AUDIO/VIDEO

OUTPUT

R

L

V

R

HDMI/DVI INPUT

Use menu for DVI audio.

COMPONENT/COMPOSITE INPUTS

R

R

FACTORY USE ONLY

Use menu for composite video.

INPUT 4

L

P

R

L

P

R

INPUT 2

ANTENNA INPUT

P

B

Y/VIDEO

P

B

Y/VIDEO

SPEAKERS

• CENTER SPEAKER INPUT To use the TV’s internal speakers as the center

speaker, connect the audio/video receiver’s center channel output to the
TV’s center channel input.

Note: Go to Center Speaker In in the Audio Connections menu to choose
the option The center channel output from an audio receiver.

AUDIO/VIDEO OUTPUTS

FIXED/VARIABLE AUDIO OUTPUTS

• CENTER Provides center surround sound to an A/V receiver or audio

amplifier.

SUBWOOFER

R

L

Note: To turn the TV’s internal speakers on and off, press MENU on the
remote control and choose Audio. Then choose Fixed/Variable Out from
the menu and choose an option.

• SUBWOOFER Provides lower bass frequencies out from the TV to a

powered subwoofer or audio receiver with a subwoofer jack.

Note: Go to Fixed/Variable Output in the Audio Connections menu to set
option to Yes if an external subwoofer is being used.

• R and L Provides right front and right rear mixed sound, and left front and

left rear mixed sound.

10 Chapter 1

• R and L REAR Provides right and left rear surround sound.

Connections & Setup

AUDIO/VIDEO

OUTPUT

R

Composite Audio Cable (RCA Type)

Composite Video Cable (RCA Type)

COMPOSITE INPUTS

R

R

INPUT 3

L

L

INPUT 1

L

V

AUDIO/VIDEO OUTPUT Connect a VCR or DVD-recorder to record digital
and analog programs from the Cable or Antenna Input (excluding copy-

V

protected programs and component video formats) while the TV is turned on.
You must leave the TV on the same channel you are recording.

• R Audio provides right audio connection and connector is usually red.

• L Audio provides left audio connection and connector is usually white.

• V (Video) provides composite video connection and connector is usually

yellow.

Notes: When recording from this output, remember to tune to the
channel you want to record.

If an unusual pattern appears when you connect a VCR to these jacks,
playing a tape or switching to the VCR’s tuner removes the pattern.

VIDEO/AUDIO INPUTS

S-VIDEO

S-VIDEO

V

INPUT 1 COMPOSITE INPUT Connect an NTSC (analog) component. These
jacks are used for most audio/video connections between components. The
audio/video jacks are often color coded (yellow for video, red for right audio,
and white for left audio).

• R Audio provides right audio connection and connector is usually red.

• L Audio provides left audio connection and connector is usually white.

Composite Audio Cable (RCA Type)

Composite Video Cable (RCA Type)

S-Video Cable

• V (Video) provides composite video connection and connector is usually

yellow.

• S-VIDEO lets you connect an S-Video cable for better picture quality to a

component with S-Video capability, such as a VCR or DVD player. When
using S-Video, make sure to connect the two audio cables as well as the
S-Video connector.

The S-Video jack provides better picture quality than the composite video
jacks because the color (chrominance, also called chroma) part of the
signal is separated from the black and white (luminance) part of the
picture.

INPUT 3 COMPOSITE INPUT Provides connection to a second NTSC
(analog) video component such as a VCR. The jacks are the same as described
above for INPUT 1.

Chapter 1 11

Connections & Setup

E

W

COMPONENT/COMPOSITE INPUTS

Use menu for composite video.

INPUT 4

R

R

Tip

Inputs 2/4 can be used as either a component
video (Y PB PR ) input or a composite video
(Y/Video) input. Go to the Connections menu,
choose Video Input Setup and select which
video input source you are using.

L

L

INPUT 2

Component Cables

THERNET

P

R

R

P

IRED

IR

P

P

B

B

Y/VIDEO

Y/VIDEO

Y (green)

(red)

P

R

P

(blue)

B

INPUT 2 COMPONENT/COMPOSITE INPUT Provides connection to a second
NTSC (analog) video component with either composite or component outputs
such as a VCR or DVD player.

• R Audio provides right audio connection and connector is usually red.

• L Audio provides left audio connection and connector is usually white.

• Y/Video PB PRUnlike a single video input, component (Y PB PR) video

maintains the video signal as three separate parts through these three jacks.
To ensure maximum picture quality, use three video-grade cables for the
Y PB PR connections. Accepts 480i, 480p, 720p, and 1080i signals. If you’re
connecting to a component with a Video jack instead, you can still use the
Y/Video jack. Go to the Connections menu, select Video Input Source and
choose Composite video as your source. Go to page 57 for more
information.

Notes: Also, remember to connect the left and right audio cables
because the Y, Pb, Pr cables carry only the picture signal, not the sound.

PIP can only be displayed from component inputs in 480i format.

INPUT 4 COMPONENT/COMPOSITE INPUT Provides connection to a
second optional component video source, such as a DVD player or satellite
receiver. The jacks are the same as described above for INPUT 2.

WIRED IR This jack is for connecting a wired remote control system, which
is primarily for professional installers. If you’re using the remote that was
included with your TV, don’t plug anything into this jack or the TV won’t
respond to the remote.

ETHERNET Connect a router, cable modem, or Digital Subscriber Line (DSL)
modem to the TV using an Ethernet cable (CAT 5) for a possible software
upgrade. Go to page 59 for more information on software upgrades. Do not
connect a telephone cable because of risk of fire or shock. A green light on the
jack means that an active network has been detected. An orange light on the
jack means the data is either being sent or received.

DIGITAL

AUDIO

OUTPUT

DIGITAL AUDIO OUTPUT Use a digital optical cable (or SPDIF cable) to
connect your TV to a compatible Dolby Digital or PCM receiver or decoder.
Dolby Digital offers theatre-quality sound (six audio channels). If you own a
receiver that uses an optical cable input, you can use an optical cable to
connect the TV to that receiver for the best sound quality. Go to the Digital
Audio Out screen in the Audio menu to select Auto Select or PCM as the output
for this jack.

Note: This TV’s optical digital output jack fully complies with the
international standard governing this type of jack (IEC958), and is
designed for connection to a Dolby Digital (AC-3® or PCM) receiver or
decoder. Older equipment, some of which is not fully compliant with
IEC958, may not be compatible with the Dolby Digital bitstream. Such a
connection using anything other than a Dolby Digital (AC-3 or PCM)
receiver or decoder could create a high noise level, causing damage to
headphones or speakers.

12 Chapter 1

Connections & Setup

o.

T

CableCARD™

HDMI/DVI INPUT

Use menu for DVI audi

CABLE

INPUT

ANTENNA INPU

CableCARD

Allows you to use a digital cable television card to receive digital
cable services, including premium and HDTV cable channels, without the need
for a set-top box. Go to page 18 for information on using the CableCARD slot.

HDMI/DVI INPUT (High-Definition Multimedia Interface/Digital Visual
Interface) Provides an uncompressed digital interface that carries both video
and audio data by way of an integrated mini-plug cable. Since HDMI is based
on Digital Visual Interface (DVI), the jack on the back of your TV is also
compatible with DVI components.

Note: If you connect a component with a DVI jack to the HDMI/DVI
input, you’ll need an HDMI to DVI adapter. Also, connect the left and
right audio cables to an input that is not in use. An example is shown
on page 17. Then go to the Audio Connections menu and select DVI
Audio Input to choose the input you’re using to receive audio.

CABLE INPUT Used to connect a coaxial cable to receive the signal from
cable or a cable box.

ANTENNA INPUT Used to connect a coaxial cable to receive the signal from
an off-air antenna.

Chapter 1 13

Connections & Setup

The Front of Your TV

Front Input Jacks

The TV has front input jacks for convenience in connecting a camcorder, digital camera, or video game system. Look for a
hinged door and press to open the cover. Please note the illustration below is just an example of how these jacks might
appear.

Notes: When you plug in headphones, the TV’s internal speakers are muted. Use the VOL up or down button to
control the volume.

When connecting a component that uses a monaural cable, such as some camcorders, use the L/MONO input jack to
get sound from both speakers.

Power Indicator Light Status

AUDIO IN VIDEO S-VIDEO

L/MONO R IN IN

On TV is on

HEADPHONE

Blinks Light blinks 5 times, pauses, and blinks again 5 times:

Lamp is trying to turn on. If the TV doesn’t turn on

after 5 minutes and then the light blinks steadily for

one minute, one of the following options is possible:

Off TV is off (standby mode)

R

E

W
O

P

+

L

O

V

—

L

O
V

H

C

H

C

U
N
E

M

Power button
and indicator

Lamp door is open. Locate the door on the side of

the TV and close it. Turn off the TV and turn back on.

The lamp should turn on.

Lamp is dead. You can replace the lamp yourself

MENU/OK

CH

CH

VOL

VOL

following the instructions on page 67. Go to page 72

for ordering information.

Lamp power supply within TV may need service. Go

to page 73 for warranty information.

Notes: The front panel illustration shows a typical front panel layout. The
exact look may be different from the one on the front of your TV.

If you use the Front Button Block feature, the front panel no longer provides
access to the menus. The Front Button Block feature disables all front panel
buttons but not the jacks. For more information, see Chapter 3.

Front Panel

If you cannot locate your remote, you can use the front panel of your TV to operate many of the TV’s features.

MENU/OK Brings up the Main menu. When the menu system is displayed, pressing MENU/OK selects highlighted items.



CH

 Scans down through the channel list. In the menu system, it moves the highlight down and adjusts menu controls.





CH

 Scans up through the current channel list. In the menu system, it moves the highlight up and adjusts menu controls.





VOL

 Decreases the volume. In the menu system, it moves the highlight left to items and adjusts menu controls.





VOL

 Increases the volume. In the menu system, it moves the highlight right to items and adjusts menu controls.



(Power button and indicator) Turns the TV on and off. The indicator lights when TV is on. Your HDTV’s lamp has a

cool-down period when the TV is turned off, and a warm up period when the TV is turned on. If you try to turn the TV on
during a cool-down, you will hear audio and then the picture will be displayed after a few moments. This could take up to
one minute. For different light status of the indicator, see above.

14 Chapter 1

Connections & Setup

L/

P

R

R

P

INPUT 2

ANTENNA INPUT

2B

P

B

P

B

DVD

L/

L/

Y/VIDEO

Y/VIDEO

OFF-AIR ANTENNA

1

CABLE

POWER

+
L

VO
—
VOL

CH
CH

U
MEN

TV

DVD

VCR

TV

CENTER SPEAKER INPUT

EXTERNAL AMP

MAX POWER RATING!

(60 WATTS into 8 OHMS)

POWER
(AC 120V~60Hz)

DIGITAL

AUDIO

ETHERNET

OUTPUT

VCR

ANTENNA OUT

CENTER

SUBWOOFER

ANTENNA IN

FIXED/VARIABLE AUDIO OUTPUTS

L REAR

R REAR

MATRIX

SURROUND

OUTPUTS

R

L

3B

IN

WIRED

IR

VIDEOAUDIO LR

CableCARD™

AUDIO

VIDEO

L

R

IN

AUDIO

L

R

OUT

VIDEO

PR PB Y S-VIDEO

L/

2A

COMPOSITE INPUTS

INPUT 3

V

R

L

S-VIDEO

AUDIO/VIDEO

OUTPUT

R

L

V

R

HDMI/DVI INPUT

Use menu for DVI audio.

L

INPUT 1

S-VIDEO

V

CABLE
INPUT

R

R

FACTORY USE ONLY

COMPONENT/COMPOSITE INPUTS

Use menu for composite video.

INPUT 4

L

L

3A

OUT

VIDEOAUDIO LR

1

How to Connect: TV + VCR + DVD Player

1. Connect your cable and/or off-air antenna.

If you have cable and an off-air antenna, connect the cable signal to CABLE INPUT. Connect the off-air antenna to
ANTENNA INPUT.

2. Connect your DVD Player to your TV.

A. Connect the audio (white and red) cables to the INPUT 4 R and L Audio jacks on the back of the TV and to the
Audio Output jacks on the DVD player.

B. Connect three video grade cables to the INPUT 4 Y/VIDEO PB PR jacks on the back of the TV and to the Y PB P
outputs on the DVD player. If your DVD player doesn’t have Y PB P

but has composite video and an S-Video output,

R,

use the INPUT 3 S-VIDEO jack instead of the V (Video) jack for better picture quality.

Notes: If you are using an S-Video cable or component video cables, you must also connect audio cables. The S-Video
cable and component video cables only transfer video information.

If your DVD player has a component video output, we recommend you use the component video input on the TV instead of
the composite video or S-Video connection.

3. Connect your VCR to your TV.

A. Connect the VCR’s audio/video outputs to INPUT 1 (R and L-Audio, and V-Video) on the TV using composite audio/video
cables.

B. Connect the VCR’s audio/video inputs to the AUDIO/VIDEO OUTPUT jacks on the TV. This enables recording of
digital and analog programs (except copy protected or component video formats).

Viewing the Components

1. Turn on the TV and the component(s) you want to view.

2. Press the TV button on the remote control.

3. Press the INPUT button on the remote control to scroll through the Video Input Channels.

•View the VCR on the INPUT 1 channel.

•View the DVD player on the INPUT 4 channel.

Note: You can set up the TV to automatically tune to the correct Video Input Channel. This is called Auto Tuning.
(See Chapter 3 for more information.)

Go to page 21

R

Chapter 1 15

Connections & Setup

ER

POW
+

VOL
—
L

VO
CH

CH
U
EN
M

TV

SATELLITE

S-VIDEO

AUDIO

VIDEO

R

L

RECEIVER

3

Satellite

Receiver

VCR

TV

CENTER SPEAKER INPUT

EXTERNAL AMP
MAX POWER RATING!
(60 WATTS into 8 OHMS)

POWER
(AC 120V~60Hz)

DIGITAL
AUDIO

ETHERNET

OUTPUT

VCR

ANTENNA IN

ANTENNA OUT

FIXED/VARIABLE AUDIO OUTPUTS

CENTER

R REAR

R

SUBWOOFER

2B

IN

L REAR

L

MATRIX

SURROUND

OUTPUTS

WIRED

IR

CableCARD™

VIDEOAUDIO LR

COMPOSITE INPUTS

INPUT 3

V

R

L

S-VIDEO

AUDIO/VIDEO

OUTPUT

R

L

V

R

HDMI/DVI INPUT

Use menu for DVI audio.

L

INPUT 1

S-VIDEO

V

CABLE
INPUT

2A

OUT

VIDEOAUDIO LR

O

R

R

FACTORY USE ONLY

COMPONENT/COMPOSITE INPUTS

Use menu for composite video.

INPUT 4

L

R

P

P

B

L

R

P

P

B

INPUT 2

ANTENNA INPUT

1

Y/VIDEO

Y/VIDEO

OFF-AIR ANTENNA

1

CABLE

How to Connect: TV + Satellite Receiver + VCR

1. Connect your cable and/or off-air antenna.

If you have cable and an off-air antenna, connect the cable signal to CABLE INPUT. Connect the off-air antenna to
ANTENNA INPUT.

2. Connect your VCR to your TV.

A. Connect the VCR’s audio/video outputs to INPUT 1 (R and L-Audio, and V-Video) on the TV using composite audio/
video cables.

B. Connect the VCR’s audio/video inputs to the AUDIO/VIDEO OUTPUT jacks on the TV. This enables recording of
digital and analog programs (except copy protected or component video formats).

3. Connect your Satellite Receiver to your TV.

Connect the satellite receiver’s audio output jacks to the INPUT 3 R and L Audio jacks and the S-Video output jack to the
S-VIDEO jack on the TV using audio cables and an S-Video cable. If your satellite receiver doesn’t have an S-Video
output, you can make the video connection by using the V (Video) jack instead. If your satellite receiver has component
outputs, then use INPUT 2 or 4.

Note: If you are using an S-Video cable or component video cables, you must also connect audio cables. The S-Video
cable and component video cables only transfer video information.

Viewing the Components

1. Turn on the TV and the component(s) you want to view.

2. Press the TV button on the remote control.

3. Press the INPUT button on the remote control to scroll through the Video Input Channels.

•View the VCR on the INPUT 1 channel.

•View the satellite receiver on the INPUT 3 channel.

Note: You can set up the TV to automatically tune to the correct Video Input Channel. This is called Auto Tuning. (See
Chapter 3 for more information.)

Go to page 21

16 Chapter 1

Connections & Setup

Component with DVI

1A

TV

CENTER SPEAKER INPUT

EXTERNAL AMP

MAX POWER RATING!

(60 WATTS into 8 OHMS)

POWER
(AC 120V~60Hz)

DIGITAL

ETHERNET

OUTPUT

AUDIO

FIXED/VARIABLE AUDIO OUTPUTS

CENTER

R REAR

R

SUBWOOFER

1B

R

Audio Out

S-VIDEO

S-VIDEO

R

R

FACTORY USE ONLY

COMPONENT/COMPOSITE INPUTS

Use menu for composite video.

INPUT 4

L

P

R

P

L

P

R

P

INPUT 2

ANTENNA INPUT

Y/VIDEO

B

Y/VIDEO

B

COMPOSITE INPUTS

V

R

L

R

HDMI/DVI INPUT

Use menu for DVI audio.

INPUT 3

L

INPUT 1

V

V

CABLE
INPUT

L REAR

MATRIX

SURROUND

OUTPUTS

AUDIO/VIDEO

OUTPUT

WIRED

L

R

L

IR

CableCARD™

2

Component with HDMI

L

DVI Out

OR

HDMI Out

R

Audio Out

L

How to Connect: TV + Component with DVI or HDMI

High-Definition Multimedia Interface (HDMI) is an uncompressed digital interface that carries both video and audio data by
way of an integrated mini-plug cable. Since HDMI is based on Digital Visual Interface (DVI), the jack on the back of your
TV is also compatible with DVI components.

1. To connect your TV to a component with a DVI jack, use an HDMI cable and an HDMI/DVI adapter.

A. Connect the HDMI cable to the HDMI/DVI INPUT jack on the back of the TV. Attach the HDMI/DVI adapter to the
end of the HDMI cable, then connect the adapter to the DVI Out jack on the back of the component.

B. Since you’re using an HDMI/DVI adapter, you need to connect Audio left and right cables to the R and L jacks on
the back of the component and to R and L Audio jacks that aren’t in use on the back of the TV.

C. Go to the DVI Audio Input option in the Audio Connections menu to select which Audio Input you’re using.

2. To connect your TV to a component with an HDMI jack, use an HDMI cable.

Connect the HDMI cable to the HDMI/DVI INPUT jack on the back of the TV and to the HDMI Out jack on the back
of the component.

Viewing the Component

1. Turn on the TV and the component you want to view.

2. Press the TV button on the remote control.

3. Repeatedly press the INPUT button on the remote control until the HDMI/DVI Video Input Channel is selected.

Note: You can set up the TV to automatically tune to the correct Video Input Channel. This is called Auto Tuning.
(See Chapter 3 for more information.)

Go to page 21

Chapter 1 17

Connections & Setup

TV

CENTER SPEAKER INPUT

EXTERNAL AMP

MAX POWER RATING!

(60 WATTS into 8 OHMS)

POWER
(AC 120V~60Hz)

DIGITAL

AUDIO

ETHERNET

OUTPUT

FIXED/VARIABLE AUDIO OUTPUTS

CENTER

R REAR

R

SUBWOOFER

L REAR

L

MATRIX

SURROUND

OUTPUTS

WIRED

IR

CableCARD™

R

R

AUDIO/VIDEO

OUTPUT

L

V

R

HDMI/DVI INPUT

Use menu for DVI audio.

Card

Digital Cable

COMPOSITE INPUTS

INPUT 3

L

L

INPUT 1

V

S-VIDEO

S-VIDEO

V

CABLE
INPUT

R

R

FACTORY USE ONLY

COMPONENT/COMPOSITE INPUTS

Use menu for composite video.

INPUT 4

L

R

P

P

B

L

R

P

P

B

INPUT 2

ANTENNA INPUT

Y/VIDEO

Y/VIDEO

CABLE

FCC Statement: This digital television is capable of receiving analog basic, digital basic
and digital premium cable television programming by direct connection to a cable system
providing such programming. A security card provided by your cable operator is required
to view encrypted digital programming. Certain advanced and interactive digital cable
services such as video-on-demand, a cable operator’s enhanced program guide and data­enhanced television services may require the use of a set-top box. For more information,
call your local cable operator.

How to Connect: TV + CableCARD

The CableCARD slot allows you to use a digital cable television card to receive digital cable services, including premium and
HDTV cable channels, without the need for a set-top box. Please contact your local cable company for availability of services
and to obtain a digital cable television card.

When you receive the digital cable card, make sure you connect your coaxial cable to the CABLE INPUT jack. Then, turn on
your TV. Insert the digital cable card into the slot on the back of the TV labeled CableCARD. Push firmly on the card until
almost the entire card is inserted. Wait to receive information on-screen regarding your digital cable television services. See
below for information on setting up digital cable television services for your TV.

You should know:

• Once the digital cable card is authorized for a particular TV, the card can’t be used with any other TV, unless it is re­authorized to it.

•You won’t receive digital cable channels if you connect your cable to the ANTENNA INPUT. Make sure you connect
your cable to the CABLE INPUT.

• Once inserted, it is not recommended you remove the digital cable card. In the case it needs to be removed, grasp
firmly, and pull the card straight out.

Setting Up Digital Cable Television Service

Once you have connected a digital cable card to the CableCARD slot on the back of the TV (explained above), you are
ready to receive digital cable channels. Wait approximately 30 seconds for the status screen to appear. Write down the
information you see and call your cable company to provide them with the information on-screen.

Notes: If your information screen disappears before you have a chance to write down the information, press MENU
on the remote to access the menu system. Then press 9, 9, 9, and the information screen appears. Go to page 58 for
more information on the CableCARD Tools menu.

You can’t order video-on-demand through your digital cable card. Call your local cable company to place an order.

Go to page 21

18 Chapter 1

Connections & Setup

Audio Connections

With the audio versatility of your HDTV, you can choose various connection options depending on the type and quality of
sound that you want. From good to best sound, choose one of the options or refer to the user’s manual of each component
that you are connecting to get the best results.

• Use your TV’s internal speakers (good sound).

• Connect audio/video receiver (speakers connected to receiver) to your TV (better sound).

• Connect audio/video receiver (speakers connected to receiver) to your TV using the digital audio output jack (best sound).

How to Connect: TV + A/V Receiver + Speakers

1. Connect the FIXED/VARIABLE AUDIO OUTPUTS from the TV to an A/V receiver using audio cables for 6-channel
matrix surround sound.

2. Be sure to go to the Fixed/Variable Out screen in the Audio Connections menu and select whether you want the FIXED/
VARIABLE AUDIO OUTPUT jacks to send fixed or variable volume audio.

• Fixed Output provides fixed-level audio output from the TV. This audio output is ideal for connecting to an A/V
receiver that has its own volume control.

• Variable Output provides variable-level audio output. Volume levels are controlled by the volume controls on
the TV and TV remote control.

3. If you connect the SUBWOOFER jack, be sure to go to the Fixed/Variable Out screen in the Audio Connections menu
and select Yes for connecting to an external subwoofer.

4. Use speaker wire to connect the audio/video receiver to your external front and rear speakers. Refer to your audio
receiver manual to complete speaker hookup to the receiver.

OR

How to Connect: TV + Receiver with Dolby Digital + Speakers

If you own a receiver with Dolby Digital* or PCM (Pulse-Code Modulation) that uses an optical cable-type input, connect an
optical cable for excellent audio quality (shown on opposite page).

1. Connect one end of the optical cable to the DIGITAL AUDIO OUTPUT jack on your TV and to the Digital Optical Input
jack on your receiver/amplifier receiver.

• If your receiver can decode Dolby Digital and PCM, go to Audio menu, select Audio Connections, then Digital
Audio Output. Select AutoSelect (recommended) or PCM option.

• If your receiver can decode only PCM, select PCM option.

2. Use speaker wire to connect the audio/video receiver to your external front and rear speakers. Refer to your audio
receiver manual to complete speaker hookup to the receiver.

Note: If you want to use your TV’s internal speakers as the Center Channel speaker, use speaker wire to connect the
audio receiver’s Center Speaker Output to the TV’s CENTER SPEAKER INPUT. Set the Center Speaker Input option in
the Audio Connections menu to The center channel output from an audio receiver option.

Go to following page for connection diagram

*Manufactured under license from Dolby Laboratories. “Dolby” and the double-D symbol are trademarks of Dolby Laboratories.

Chapter 1 19

Connections & Setup

er

B

+

–

ack of Right Front Speaker

–

+

–

Back of Right Rear Speaker

TV

CENTER SPEAKER INPUT

EXTERNAL AMP

MAX POWER RATING!

(60 WATTS into 8 OHMS)

POWER
(AC 120V~60Hz)

DIGITAL

AUDIO

ETHERNET

OUTPUT

L

R

FIXED/VARIABLE AUDIO OUTPUTS

CENTER

R REAR

SUBWOOFER

OR

DIGITAL
AUDIO
INPUT

CD

IN

IN

COMPOSITE INPUTS

L REAR

MATRIX

SURROUND

OUTPUTS

WIRED

R

L

IR

CableCARD™

AUDIO/VIDEO

OUTPUT

R

L

V

INPUT 3

R

L

R

L

HDMI/DVI INPUT

Use menu for DVI audio.

INPUT 1

V

S-VIDEO

S-VIDEO

V

CABLE

INPUT

R

R

FACTORY USE ONLY

COMPONENT/COMPOSITE INPUTS

Use menu for composite video.

INPUT 4

L

R

P

P

B

L

P

R

P

B

INPUT 2

ANTENNA INPUT

Y/VIDEO

Y/VIDEO

+

–

Back of Left Front Speak

A/V AMPLIFIER

CENTER

SURROUND SPEAKERS

REAR

RIGHT

LEFT

+
–

Back of Left Rear Speaker

TAPE

VCR

OUT

IN

OUT

Surround

TV

CENTER

IN

FRONT SPEAKERS

RIGHT

SL

LEFT

+
–

SUBWOOFER

SR

+

–

20 Chapter 1

Connections & Setup

Plug in the TV

Plug the flat end of the cable into the power jack on the back of the TV. Then plug the other end
of the power cord into an appropriate wall outlet. Be sure to insert the plug completely. Do not
plug the TV into an outlet controlled by a light switch.

Note: When you first plug your TV into an outlet, the Power indicator on the front panel
will light and blink for approximately 30 seconds and then go off during the initialization
of the TV. The TV can only be turned on after the Power indicator goes off. This happens
every time the TV is unplugged and plugged back in.

Put Batteries in the Remote

• Remove the battery compartment cover from the back of the remote
by pushing down on the tab and lifting cover.

• Insert 2 fresh “AA” batteries. Make sure the polarities (+ and -) are
aligned correctly with the polarities inside the remote.

• Replace the cover.

Tip

When remote batteries are low, the component
button corresponding to the mode you’re in
flashes when you press a button. Also, a message
might appear on the TV screen and disappear
within a few seconds. Press CLEAR and replace the
batteries to remove the message.

ON-OFF

learning

TV
button

MENU button

DVD VCR

SAT

/

CAB

PIP

PRESETS

CC

CCCC

FORMAT INFO

CLEAR

CC

SWAP

TV

AUX

CH. CTRL

FAV

AUDIO

FREEZE

LIGHT

i

MENU

MM

OK button
Arrow

SOUND

SKIP

buttons

Turn on the TV

Press TV on the remote, or press the Power button on the TV’s front
panel.

Note: Pressing the TV button turns on the TV and puts the remote
into TV mode. “TV mode” means that the buttons on the remote
control operate the TV’s functions.

Use the Remote Control to Complete
the Assisted Setup

The technical term is “Navigation” – how you move through the on-screen
menus. The method is the same throughout the menu screens: highlight
your choice and select it.

To highlight a menu item, put the remote into TV mode by pressing the
TV button then MENU. Press the arrow buttons on the remote to highlight
one of the items listed in the menu. Use the up or down arrow button to
move up or down. Use the right or left arrow button to move right or left.

To select the item that you’ve highlighted, press OK.

Note: Highlighted means that the menu item stands out from
other menu items on the list (appears darker, brighter, or a
different color).

Tip

To access the setup menus, press MENU and
choose Assisted Setup.

Chapter 1 21

Your TV’s menu system allows you to adjust your TV’s features to be
configured to work properly. On-screen information helps you choose
settings to match your setup. The first time you turn on your TV, the
Assisted Setup screens appear automatically. Select Begin Setup to start or
select Cancel Setup to exit.

Complete the Assisted Setup

Connections & Setup

Go Back

0

Closed CaptioningContinue Setup

1

Cancel Setup

2

Go Back

0

Continue Setup

1

Cancel Setup

2

Main Menu Preferences

English

Highlight with the and  arrows. Select with the OK button.

Español

Resalte con las flechas  y . Seleccione con el botón OK.

Français

Mise en surbrillance avec  et . Sélection avec OK.

Press  or  to point to an option, then press OK to
select it. Press to return to the menu.

Main Menu Assisted Setup

Input to search:

Cable Input



Antenna Input



Channels to search:

Digital channels





Analog channels

Other search options:

Detect antenna or cable setting





Include previously found channels in search

Start

Pressto make changes to this screen's settings.
Press OK to skip to the next step in the setup routine.

Channel Search

Channel Search finds channels
for you. Check fewer boxes to
make the search faster (but
less complete) and vice versa.

The first time that you do a
Channel Search, put a check in
all the boxes to do a thorough
search for channels.

To add a channel that Channel
Search didn't find, clear all
menus and directly tune to the
channel with the number keys.

Tip

The first Channel Search takes several minutes if
the TV is searching for analog and digital
channels and cable and antenna inputs are
being searched. You may want to leave and
come back later.

Set the Menu Language

1. Use arrow buttons to highlight your preferred language for the
menu system.

2. Press OK to select that language.

3. Select Continue Setup.

Complete Channel Search

Even though this initial channel search can take several minutes, it is important
to complete in order for your TV to display channels and programming. Make
sure you have connected cable and/or off-air antenna to the corresponding
inputs before you start channel search.

1. To do a complete channel search, check each box that pertains to your TV.
For example, if you’re only receiving cable from the CABLE INPUT,
highlight Cable Input and press OK to place a checkmark in the box.

2. Select Start to begin the setup.

3. When the channel search is complete, a message screen appears. Select
Continue. Another message screen appears telling you that you’ve
completed the Assisted Setup. Select Continue on the left.

Notes: If you skip Channel Search now, you can access it later through
the Connections menu. See Chapter 4 for more details.

If a cable box is connected to your TV’s CABLE INPUT or a CableCARD
is in use, Channel Search won’t work for Cable Input.

Changing Channels

Depending upon the type of signals you have connected to your HDTV, you
might notice that the channels change slower than you’re used to. This is
perfectly normal. Your HDTV is able to interpret and display both analog
(NTSC) and digital off-air and cable signals (QAM and ATSC).

Next Steps

Now that you’ve finished the Assisted Setup, you’re ready to watch TV. This
might be a good time to program your remote control. The remote control that
came with this TV can be programmed to operate other components. Go to the
next chapter to find out how to program your remote.

• Chapter 2: Using the Remote Control

• Chapter 3: Using the TV’s Features

• Chapter 4: Using the TV’s Menu System

• Chapter 5: Reference

22 Chapter 1