RCA G27669YX2AX1, G27669YX1AX User Manual

WARNING

To reduce the risk of fire or
shock hazard, do not expose

this TV to rain or moisture.

]

To reduce the risk of electric shock, do not remove
cover (or back). No user serviceable parts inside.

Refer servicing to qualified service personnel.

This symbol indicates

"dangerous voltage" inside

the product that presents a
risk of electric shock or

_, This symbol indicates

important instructions
accompanying the product.

personal injury

Caution: To reduce the risk of electric shock, match
wide blade of plug to wide slot, fully insert.

Attention: Pour _viter les chocs 6lectriques, introduire

la lame la plus large de la fiche dans la borne

correspondante de la prise et pousserjusqu au fond.

Refer to the identification/rating label located on the back panel of your
product for its proper operating voltage.

FCCRegulations state that unauthorized changes or modifications to this

equipment may void the user's authority to operate it.

If fixed (non-moving) images are left on the screen for long

periods, they may be permanently imprinted on the screen. Such

images include network Iogos, phone numbers, and video games.

This damage is not covered by your warranty. Extended viewing
of channels displaying these images should be avoided.

Cable TV installer: This reminder is provided to call your attention to

Article 820-40 of the National Electrical Code (Section 54 of the Canadian

Electrical Code, Part 1) which provides guidelines for proper grounding
and, in particular, specifies that the cable ground shall be connected to the
grounding system of the building as close to the point of cable entry as

practical.

Product Registration

Please fill out the product registration card and return it immediately. Returning the card allows us to contact you
needed.

Keep your sales receipt to obtain warranty parts and service and for proof of purchase. Attach it here and record the

serial and model numbers in case you need them. The numbers are located on the back of the television.

Model No.

Serial No.

Purchase Date:
Dealer/Address/Phone:

VCR Plus+, C3,PlusCode, GUIDE Plus+, and GUIDE Plus+ Gold are trademarks of Gemstar Development
Corporation.

The GUIDE Plus+ Gold system is manufactured under license from Index Systems Inc.

SETUP AND CONNECTIONS .......................................................... 3

Step 1: Unpack the TV ...................................................................... 4

Step 2: Connect Your TV .................................................................. 4

TV Only (PIP Not Available) ....................................................... 4

The Basic Connection (PIPNot Available) ................................ 5

Advanced Connections .............................................................. 6

Back of the TV ............................................................................ 6

Sample Connections .................................................................. 7

Step 3: Connect the IR Controller .................................................... 9

Step 4: Plug in the TV ..................................................................... 10

Step 5: Place Batteries in the Remote ........................................... 10

Step 6: Turn On the TV ................................................................... 10

On-Screen Program Guide ....................................................... 10

Step 7: Program the TV .................................................................. 10

INTERACTIVE SETUP .................................................................... 11

Using Point and Select ................................................................... 12

Entering Setup ................................................................................ 12

Selecting a Language ..................................................................... 13

Auto Channel Search ..................................................................... 13

The GUIDE Plus+ Gold System ....................................................... 14

Setting Up the GUIDE Plus+ Gold System ............................... 14

Setting the Time ............................................................................. 16

Setting the VCR1 Channel (auto tuning) ..................................... 17

Setting the VCR2 Channel (auto tuning) ...................................... 17

Setting the DVD Channel (auto tuning) ....................................... 18

Setting the SAT/CABLE Channel (auto tuning) ............................. 19

Labeling the Channels ................................................................... 20

USING THE REMOTE ..................................................................... 21

Remote Buttons .............................................................................. 22

Using the WHO,INPUT Button ................................................ 23

Programming the Remote ............................................................. 24

Testing the Remote .................................................................. 24

Using the Remote to Control a Device ................................... 25

Modes of Operation ................................................................ 25

Front Panel ..................................................................................... 25

1

USING THE MENU SYSTEM ......................................................... 27

Menus and Control Panels ............................................................. 28

Audio Menu ....................................................................................30

Using the Remote to Select an Audio Processor .......................... 31

Picture Quality Menu ..................................................................... 32

Screen Menu ................................................................................... 33

Using Closed Captioning ......................................................... 34

Channel Menu ................................................................................ 35

Time Menu ...................................................................................... 36

Other Menus ................................................................................... 36

FEATURES AND CONTROLS ......................................................... 37

GUIDE Plus+ Gold Menu ................................................................ 38

About the GUIDE Plus+ Gold System ............................................ 38

Getting In & Out of the GUIDE Plus+ Gold System ................ 39

Downloading Data .................................................................. 39

The Different GUIDE Plus+ Gold System Menus .................... 39

Grid Guide ........................................................................... 40

Sort ...................................................................................... 41

Schedule .............................................................................. 42

Messages ............................................................................. 43

Editor ................................................................................... 43

PIP (Picture-in-Picture) Operation ................................................. 45

Channel Marker .............................................................................. 46

Parental Controls and V-Chip ........................................................ 47

V-Chip TV Rating Limit ............................................................ 48

V-Chip Movie Rating Limit ...................................................... 52

V-Chip Unrated Program Block ............................................... 53

Channel Block .......................................................................... 53

Front Panel Block ..................................................................... 53

Lock/Unlock Parental Controls ................................................ 53

REFERENCE ..................................................................................... 54

Troubleshooting ............................................................................. 54

Care and Cleaning .......................................................................... 55

RCA Limited Warranty ................................................................... 56

Accessory Information ................................................................... 58

INDEX ............................................................................................. 61

2

GETTI NG STARTED

This manual is designed to get you started quickly.
The first five sections of the manual show you how to

get your TV set up and connected, run the Interactive
Setup, program the remote, and use all of the menus,

features, and controls of your TV.
The reference section in the back of the book

contains troubleshooting tips, care and cleaning

instructions, accessory ordering information and your

warranty.
Well... if your TV's out of the box, let's get started.

SETUP AND CONNECTIONS

V

V

V

V

V

I •

Check out the notes that have been added

throughout the manual in theseTip
Boxes.There are some important tips that
will help you get the mostfrom your TV.

#

3

STEP 1: UNPACK THE TV

Make sure to locate the remote control.

STEP 2: CONNECT YOUR TV

There are three types of connections outlined in this section:
TV Only: If you're only going to connect the TV to

your home antenna or cable system.

The Basic Connection: If you're going to connect the TV to a

VCR or satellite receiver.

Advanced Connections:

If you're going to make multiple

connections, hooking up the TV to a
VCR and a satellite receiver.

Cable information and illustrations are given for each type of connection.
Once you have completed your desired connection you may skip forward

to Step 3.

TV ONLY (PIP NOT AVAILABLE)

This is a basic connection from an antenna or cable system to your TV.
Connect the cable into the Cable/Antenna jack as shown.

Cables

You will use the following cable to make your connection:

Coaxial Cable: These cables carry audio and
video signals to the TV from an antenna, cable,

or cable box.

r

Important Stand Information

CAUTION: Choose the location for your TV
carefully. Take precautions that the stand

or other furniture on which the TV is
placed is properly located (see Important

Safeguards sheet) and of adequate size
and strength to prevent the TV from
accidentally being tipped over, pushed off,
or pulled off. This could cause damage to
the TV and/or personal injury.

r

Before You Connect

Protect against power surges:

• Connect all components before

plugging any power cords into the wall
outlet.

• Turn offthe TV and/or component

before connecting or disconnecting any
cables.

• Make sure all antennas and cables are
properly grounded. Refer to the

Important Safeguards sheet packed
with your TV.

CABLE, CABLE BOX, OR ANTENNA

TV

CABLE/CONTROL (_ ANTENNA

Once you have completed this connection you may go to Step 3.

rThis Connection Will Not Allow

You to Use Your PIP

Your TV is equipped with a single tuner,
which means you must connect with a
second video source using Audio/Video
Cables to view PIR This TV Only
connection will not enable you to use
your PIP,but will get your TV up and
running quickly.

Refer to Advanced Connections for
connecting Audio/Video cables to your

VCR or other video component.

4

THE BASIC CONNECTION (PIP NOT AVAILABLE)

The basic connection below (TV and VCR) is the most common
connection and is therefore used to illustrate a single component

connection with your TV. For better sound and picture quality and

multiple component connection information refer to the next section,

Advanced Connections.

Cables

You will use the following type of cable to make your connection:

Coaxial Cables: In this connection, two Coaxial
Cables are used: one connects from an antenna,
cable, or cable box to the VCR, and one connects

from the VCR to the TV. These cables carry both

audio and video signals.

CABLE, CABLE BOX, OR ANTENNA

This Connection Will Not Allow
You to Use PIP

Your TV is equipped with a single tuner,
which means you must connect with a
second video source using Audio/Video

Cables to view PIR This Basic Connection
will not enable you to use your PIP,but

will get your TV up and running quickly.
Refer to Advanced Connections for

connecting Audio/Video cables to your
VCR or other video component.

VCR 1

I OUT

Q 0

VIDEO AUDIO

TV

IN FROMANTCH3ouT__TO TV CH4[_ I

CABLE]

ANTENNA

How to View the VCR

To watch the VCR in this connection tune TV to
Channel 3 or 4.

Later, in the Interactive Setup section you will
program the TV to automatically tune to

Channel 3 or 4 when you turn on the VCR.

Once you have completed this connection you may skip to Step 3.

5

ADVANCED CONNECTIONS

Advanced connections give you better sound and video by separating
the audio and video signals and enabling you to connect multiple

components.
This section describes the types of inputs available on the back of your

TV and suggests ways you can use them for optimum performance.

BACK OFTHETV

Once you have made your connections,

you will need to program the TV to tune
to the correct Video Input channel in

order to see and hear audio and video
from a component such as a VCR or DVD

player. You will program this later in the

Interactive Setup.

k

The diagram below describes each of the back panel jacks. When
connecting A/V cables, be sure to connect corresponding OUTPUTS and

INPUTS (Video to Video, Right Audio to Right Audio, etc.).

VIDEO and Audio Inputs |

J

Connect any one of thefollowing components:

VCR Internet Access Device

• Laserdisc Player • DVD Player

• Satellite Receiver

To view the component connected to VIDEO,

use the WHO,INPUT button on the remote,

\

_ VID[O

[o

VCR

CONTROL

Audio Outputs

Connect to an audio receiver or
amplifier for variable controlled

or fixed level stereo output.

/

our

CABLE/

S._DEO O ANTENNA

VCR Control

Connect the GUIDE Plus+
Gold system IR controller

for one-button recording
and channel tuning from

the GUIDE Plus+ Gold
system.

T /

S-Video

This optional
connection can

be used for
better video

quality picture.

I CablelAntenna

Takes the signal input from a cable,
cable box, or an off-air antenna. Can als(

be used for basic component connections.

6

SAMPLE CON NECTIONS

The following are sample connection scenarios you may encounter
when connecting components to your TV. Note: components that offer

an S-Video connection, such as DVDs, VCRs or satellite receivers, must

match their S-Video connection with their audio INPUT connection.

Cables

You will use the following types of cables to make your connection:

Coaxial Cables: Carries the signal from the
antenna or cable directly to the television or

through a cable box, as needed by your cable
system.

Audio/Video Cables: Carries audio and video
from a component to the TV.

S-Video Cable: Carries video from an S-Video
capable component which provides best picture
quality.

TV and Stereo VCR

Compared to the Basic Connection, using Audio/Video and
S-Video (if available) cables will enhance the sound and picture

quality from a component.

CABLE, CABLE BOX, OR ANTENNA

VCR 1

DEO R L

Io o o]'"

R

CONTROL _

_ S VEDEO

Cautions:

Position cables to avoid audio hum
or interference

• Insert all cables firmly into jacks.

• Place the audio/video cables to the

sides of the TV's back panel instead of
straight down the middle.

• Try not to coil any twin-lead cables and

keep them away from the audio/video
cables.

Protect your components from
overheating

• Do not block ventilation holes in any of

the components. Arrange the
components so that air can circulate

freely.

• Do not stack components.

• Allow adequate ventilation when

placing your components in a stand.

• Place an amplifier on the top shelf of

the stand so heated air rising from it
will not flow around other

components.

How to View Your VCR

To watch the VCR in this connection, press
TV to put the remote control into TV

mode, then press WHO.iNPUT to toggle to

the video (VID) inputs.

In the Interactive Setup section you can
program the TV to automatically tune to

the VID input channel when you turn on
the VCR.

Most Audio/Video cables are combined
into one cable with three heads on each

end.

We show individual
cables in these sample V,deo(yellow)
connections. Either

may be used, but _ ReghtAud,o(red)

yOU must be sure to

connect Video to _Left Audio (wh te)

Video, Right to Right
and Left to Left.

7

TV, VCR and Satellite Receiver

CABLE, CABLE BOX, OR ANTENNA

SATELLITE RECEIVER

VCR 1

SATELLITE SIGNAL

How to View Your Components

To watch the satellite receiver in this
connection, press TV to put the remote control

into TV mode, then press WHO*INPUT to scroll

through the video input channels until you
tune to VID (or SVID) input.

To watch the VCR in this connection, enter 03
to tune to the VCR channel.

In the Interactive Setup you can program the

TV to automatically tune to the correct input
channel when you turn on your component.

TV

8

STEP 3: CONNECT THE IR CONTROLLER

The IR (Infrared) Controller enables the GUIDE Plus+ Gold system to
control your VCR and cable box (if necessary) so you can tune to
television channels and even start recording a program from the GUIDE

Plus+ Gold system,

After you have affixed the ends of the controller to the necessary
component (VCR, or Cable box), use the on-screen interactive setup

routine for the GUIDE Plus+ Gold system to test the connected

components.

The 1,9Controller is used to send commands to your
VCR and/or cable box.

ATTACHING THE IR CONTROLLER

Some components have a labeled infrared remote sensor, and others do
not. If your component is labeled, affix the IR controller directly over the

sensor. If the IR location is not labeled on your component, you need to

use to use the component's remote control to locate the season

1. Hold the component's remote control (not the remote that came
with your TV) so that it is touching the front of the component.

2,

Slowly move the remote over the front of the component while
pressing the remote power button on and off. (Be sure to press and

release the power button each time you move the remote. Holding

the button may not work.)

3.

4.

When the component turns off or on, you've located the sensor.
Affix the controller's node directly to the remote sensor.

II ......I

i []1

Attach to the VCR °÷'°7" /

o

"÷ Attach to the cable box. If you do not

have a cable box, just leave it unattached.

Connect to the TV

Tip

You may want to use a piece of clear

plastic tape to temporarily affix the
controller's node until you have completed
the interactive setup. That way you can
easily move it if you have not placed it
exactly over the sensor.

9

STEP 4: PLUG IN THE TV

Plug the end into the wall outlet, matching the wide blade of the plug

with the wide slot in the outlet. Be sure to insert the plug completely.

STEP 5: PLACE BATTERIES IN THE

REMOTE

Remove the battery compartment cover from the back of the

remote.

Insert fresh batteries. Make sure that the polarities (+ and -) are

aligned correctly.

Replace the cover.

STEP 6: TURN ON THE TV

PressTV on the remote, or press POWER on the TV itself.
Pressing the TV button not only turns on the TV, but puts the remote

into TV mode, so that the buttons on the remote will control TV

functions.

ON-SCREEN PROGRAM GUIDE

The TV is designed to bring up the GUIDE Plus+ Gold on-screen program
guide when you use the TV button on the remote to turn on the TV

(after you have set up the GUIDE Plus+ Gold system). For more
information on setting up the GUIDE Plus+ Gold system, see the next

section, Interactive Setup.

To get out of the GUIDE Plus+ Gold System:

PressOK to exit the GUIDE Plus+ Gold system and tune to the
highlighted channel.

PressGUIDE to exit the GUIDE Plus+ Gold system and tune to the

channel displayed in the View window.

PressCLEAR to exit the GUIDE Plus+ Gold system and go to the last

channel you were watching.

STEP 7: PROGRAM THE TV

Proceed to the next section, Interactive Setup. The interactive setup

routine walks you through the steps needed to fully configure the TV.

10

THERES AN ON-SCREEN SETUP ROUTINE

The interactive setup routine helps you through the steps

needed to configure the TV and set up the GUIDE Plus+

Gold menu system:

Select a menu language
Search for available channels

Set up the GUIDE Plus+ Gold system
Set the time

Set the VCR1 channel
Set the VCR2 channel
Set the DVD channel
Set the SAT/CABLE channel

Make the channel list and labels

2

V

I NTERACTIVE SETUP

V

V

I

V

V

11

USING POINT AND SELECT

You only need to know one rule when using the remote to access on-
screen menus and control panels: point and select. The point and select

method has two steps.

1. Point to a menu item using the MOVE arrows on the remote.
To point up or down, press the up or down arrows. To point left or

right, press the left or right arrows.

2. Select a menu item by pressing MENU or OK.
Selecting an item tells the TV's menu system to go ahead and make

the change or go to a place you have indicated.

ENTERING SETUP

The first screen of the Interactive Setup appears automatically when
you turn on your TV for the first time or after a power outage.

1. PressMENU to begin setup or CLEAR to exit.

CLEAR

Point and Select

buttons

You can also access the Interactive Setup through the Main menu:

1. PressMENU to bring up the Main menu.

2,

Point to Setup and press MENU or OK. The first Setup screen comes
up, asking you to confirm that you want to begin.

You can also select a menu item by
entering the item number with the

number buttons on the remote.
Press CLEARat any time to remove all

displays from the screen and return to TV

viewing.

Many VCR user manuals refer to a
PROGRAM button. The MENU button on

this remote works as a PROGRAM button

in VCR mode. Other manuals may refer to
a SELECTbutton. The OK button on this

remote works as a SELECTbutton.

12

3. Point to Begin setup now and press MENU or OK.

SELECTING A LANGUAGE

The first part of the setup routine asks you to select your preferred

language for the menu system.

1. Point to your preferred language for the menu system.

2. Press MENU or OK to select that language.

AUTO CHANNEL SEARCH

The next part of the setup routine asks you if you want the TV to search
for all channels viewable through your antenna or cable TV system. This

is sometimes called "auto programming."

1.

Press MENU or OK to tell the TV to begin searching for channels.

The display gives you a progress report and tells you when it has
finished.

I If you skip Auto Channel Search now, you I

-I

can access it later through the Channel

J

menu. See Using the Menu System for
more details.

13

THE GUIDE Plus+ GOLD SYSTEM

The next step lets you set up the GUIDE Plus+ Gold system to display your local

program listings, and control your cable box and VCR.

You can either press MENU or OK to bring up the GUIDE Plus+ Gold initial menu or

point to Skip this Stepto move to the next step in the Interactive Setup.

I You can set up the GUIDE

Plus+ Gold system during |

Interactive Setup or by I

selecting the GUIDE Plus+ |
Menu from the Main Menu,/

2

GUIDE Plus+

SETTING UP THE GUIDE Plus+ GOLD SYSTEM

To complete GUIDE Plus+ Gold setup, the GUIDE Plus+ Gold IR controllers must be connected to your cable box
and VCR if you have them. Refer to the Setup and Connections section for additional information.

Select your Country and enter your ZIP
or Postal code.

The next series of screens asks you
about your cable TV setup. If you have

a cable box, you need to set the
GUIDE Plus+ Gold system to control it.

Otherwise, it may not be able to

locate and download program
information.

Tune your cable box to Channel 2 and
then select the brand of your cable

box from the choices available. The

system then searches for the correct
code to control your cable box. When
your cable box switches to channel 9 it

has located the correct code.

14

Select YESif the cable box changed to channel 9, or NO if it did not. If you select NO, the system will try
another code.

If the GUIDE Plus+ Gold system cannot recognize either your cable box or VCR after several tries, a screen
stating "Cable Box (VCR) test failed...Please consult your manual and try again" appears. You have a
choice to either Try Again or Skip Cable Box Setup. If you get this message, you should also:

Double check the brand of your cable box or VCR, and try entering it again.
Check to make sure the IR controllers are positioned correctly.

If you choose to skip the cable box (or VCR) setup some features of the guide may not be available until

you successfully complete this procedure.

Once the correct model of cable box (or
VCR) has been identified, you need to set

the cable box's output channel. Enter the
channel you use to view channels through

your cable box--usually 3 or 4. Consult
your cable box's instruction book or your

cable company if you are not sure. Choose

Oto use VIDEO INPUT.

Select YESif you have a VCR, or NO if not.

(Answering NOautomatically skips forward
to the end of GUIDE Plus+ Gold setup.)
Tune your VCR to channel 2 and rum it off.

Enter the brand of your VCR.

When the GUIDE Plus+ Gold system correctly
identifies the correct code for your VCR,
the VCR's tuner changes to channel 9.
Select YESif the VCR automatically changed

to channel 9, or NO if it did not.
If you select NO, the system will try another

code.

The last screen comes up when you've
successfully finished the GUIDE Plus+ Gold
setup.

Remember:

Leave your cable box turned ON to download program information.
Leave your VCR turned OFF to record programs.

PressOK to leave the GUIDE Plus+ Gold system setup and either return to the TV's Interactive Setup or the Main Menu. For
more information about the GUIDE Plus+ Gold system, see the section Features and Controls.

15

SETTING THE TIME

The next step in the Interactive Setup lets you set the time of day. If your
GUIDE Plus+ Gold system has not completed its first download, you need
to set the time, Once the system has completed its first download, it sets
the time for you automatically.

Set time

1. Press MENU or OK to bring up the Set Time control panel.

2,

Use the left and right arrows to point to the hour and minutes

spaces, Use the digits to enter the numbers and the up and down
arrows to change from AM to PM,

3. Press MENU or OK to continue.

16

SETTING THE VCR1 CHANNEL (AUTO
TUN I NG)

The next step lets you set the VCR1 channel. When you set the VCR1
channel, you're telling the TV what channel to tune to when you press
the VCR1 button on the remote. This is called auto tuning.

Indicate which input you used to connect the VCR. If you don't have a

VCR1 component connected to the TV, skip this step or select Not

Connected from the VCR1 Channel choice list. (For more, see Auto

Tuning in the Using the Menu System section.)

1. Press MENU or OK to bring up the VCR1 choice list.

2. Point to the choice that matches the way you have your VCR

connected to the TV.

3. Press MENU or OK to continue.

SETTING THE VCR2 CHANNEL (AUTO
TUN I NG)

The next step lets you set the VCR2 channel. When you set the VCR2
channel, you're telling the TV what channel to tune to when you press
the VCR2 button on the remote.

Indicate which input you used to connect a second VCR. If you don't
have a second VCR component connected to the TV, skip this step or

select Not Connected from the VCR2 Channel choice list. (For more, see
Auto Tuning in the Using the Menu System section.)

17

Use TV with VCR 2

1. Press MENU or OK to bring up the VCR2 choice list.

2. Point to the choice that matches the way you have your second VCR
connected to the TV.

3. Press MENU or OK to continue.

SETTING THE DVD CHANNEL (AUTO
TUNING)

The next step lets you set the DVD channel. When you set the DVD
channel, you're telling the TV what channel to tune to when you press

the DVD button on the remote.

Indicate which input you used to connect a DVD player. If you don't have
a DVD player connected to the TV, skip this step or select Not Connected
from the DVD Channel choice list. (For more, see Auto Tuning in the

Using the Menu System section.)

Use TV with DVD

1. Press MENU or OK to bring up the DVD choice list.

18

2. Point to the choice that matches the way you have your DVD player
connected to the TV.

3. Press MENU or OK to continue.

SETTI NG THE SAT/CABLE CHANNEL (AUTO

TUN I NG)

The next step lets you set the SAT/CABLE channel. When you set the SAT/CABLE
channel, you're telling the TV what channel to tune to when you press the
SAT.CABLE button on the remote.

Indicate which input you used to connect a satellite receiver or a cable box. If

you don't have a satellite receiver or cable box connected to the TV, skip this
step or select Not Connected from the SAT/CABLE Channel choice list. (For

more, see Auto Tuning in the Using the Menu System section.)

1. Press MENU or OK to bring up the SAT/CABLE choice list.

2. Choose how the TV and satellite receiver or cable box are connected.

3. Press MENU or OK to continue.

19

LABELING THE CHANNELS

This last step in the Interactive Setup lets you edit your channel list and

label your channels. (For more, see List and Labels in the Using the
Menus section.)

Name channels

r

Use the CH ^ (channel up) or CH v

(channel down) buttons to change
channels in the Chan # field. This works

even if you're not in the Chart # field. Or,
enter the channel number directly using

the number buttons on the universal
remote. To enter a number greater than

99, press and hold "1" to enter the
hundreds digit, then press the two
remaining numbers.

The list and labels feature can also be
accessed from the Channel menu. Because

this procedure can be time consuming,
feel free to skip this step and come back

to it later.

m

1. Press MENU or OK to bring up the List and Labels control panel.

2.

3.

4.

Use the left and right arrows to point to the three different areas of

the control panel (called "fields").

Use the up and down arrows to scroll through the numbers and
letters and select Yesor No in the Normal List field. You may wish to

refer to the call letters listed in your newspaper's TV section for ideas
on labeling the channels.

Repeat this process for each of your channels. Then press MENU or

OK to continue. The TV can store up to 27 labels in memory

WHAT NOW?

Now that you've finished the interactive setup, you can sit back, relax,

and enjoy the TV. Or...

PROGRAM THE REMOTE

Since you've gone this far, you can take a few minutes to program the
remote to control your VCR, DVD player, satellite receiver, or other

components. To find out how to program the remote, go to the next
section.

20

HOW TO USE YOUR UN IVERSAL REMOTE

This section defines the buttons of the remote and

how to program it to control other components.

The universal remote can be programmed to control

most brands of remote controllable VCRs, satellite

receivers, and cable boxes. If you have an RCA, GE,
or PROSCAN component, you probably don't need
to program it at all.

V

V

USING THE REMOTE

V

I

V

V

Modes of Operation /

1

Because this universal remote can control
several different components (DVD

player, VCR, cable box, etc.), it uses
operational modes triggered by the

component buttons. For example if you
want the remote to control the TV,you

would press the TV button to put the

remote into TV mode before you could

control the TV.

21

REMOTE BUTTONS

ON-OFF When in TV mode, turns TV on and off. If in another device

mode (VCR, DVD, Satellite, etc.) and programmed, will turn the device
on and off. When pressed twice within two seconds, all devices that are

on will be turned off (this feature only works with most RCA,
PROSCAN and GE products).

VCR1 Puts the remote in VCR mode and if auto tuning is enabled, it will
turn on the TV and tune to the correct channel.

TV Turns on the TV and puts the remote in TV mode. Also displays
channel information.

DVD Puts the remote in DVD mode and if Auto Tuning is enabled, it will
turn on the TV and tune to the correct channel.

VCR2 Puts the remote in VCR2 mode and if Auto Tuning is enabled, it
will turn on the TV and tune to the correct channel.

AUX When pressed, will turn on the component you have programmed

it to control. Also turns on the TV if Auto Tuning is enabled and remote

is programmed to control a TV.
SAT-CABLE Puts the remote in SAT.CABLE mode and if Auto Tuning is

enabled, it will turn on the TV and tune to the correct channel.
MUTE Reduces the TV's volume to its minimum level. Press again to

restore the volume.

SKIP Press once before changing channels and the TV will wait 30
seconds before returning you to the original channel. Press repeatedly

to add more time.
CH ^ or CH v Scans up or down through the current channel list. Press

once to change the channel up or down; press and hold to continue
changing channels.

VOL< or VOL> Decreases or increases the TV's volume.

SOUND Press once to display the audio processor choice list. Point and

select to choose a different processor or press CLEAR to exit.
LIGHT ICON Pressto illuminate the remote's buttons. The light

automatically shuts off within a few seconds of the last button press.

GO BACK Returns you to the previous channel.
GUIDE Brings up and exits the GUIDE Plus+ Gold system. In SAT.CABLE

mode, brings up available on-screen guides.

INFO Brings up channel information.
MOVE (Arrows) Used to point to different items in the menu system.

Also used to adjust the menu controls. Also move the PIPwindow when

no menus are on the screen.
OK When in the menu system, selects highlighted items or returns you

to the previous menu.

LED

VCRI TV

<1

DVD VCR2 AUX SAT.CABL[

&&°& &

MUTE SKIP

SOUND G0 BACK
GUIDE INFO

MENU CLEAR

,@0@,@

ANTENNA

REVERSE PLAY FORWARD

REC'VCR÷ STOP PAUSE

PiP SWAP CHCTRL RESET

©O©O

22

MENU Brings up the Main menu and selects highlighted items. When in

VCR mode, it functions as a PROGRAM button.

CLEAR Removes any menu or display from the screen and returns you

to TV viewing. Also exits the GUIDE Plus+ Gold menu system.

(019) Number Buttons Enters channel numbers, digits for

programming the remote, and time settings directly though the remote

control. To enter a two-digit channel, press the two digits. To enter a

three-digit channel, press and hold the first digit, release, then add the

second two. Example: to tune to channel 123, press and hold 1, release,

press 2, then press 3.

WHO-INPUT In TV mode, press to toggle through the available input

sources (VlD/SVlD and the current channel). In SAT mode, press to select

available channel lists.

ANTENNA Functions as TV/VCR button in VCR mode and TV/receiver

button in SAT,CABLE mode.

REVERSE, PLAY, FORWARD, REC-VCR+, STOP, PAUSE If programmed,

provides transport control for some remote-controllable VCRs, DVD
players, laserdisc players, tape decks, and CD players. Pressing REC.VCR+

when using the GUIDE Plus+ Gold system sets the VCR to record a

program.

PIP Brings up the small picture-in-picture window. Press again to

remove the PIP window. When PIP Caption Display - Alternate with PIP -

has been selected, will display captioning in the PIP window.

SWAP Swaps the main picture with the PIP window.

CH CTRL Selects the picture window (that is, the main or PIP window)

to be changed by the CH ^ (channel up), CH v (channel down), or

WHO.INPUT buttons.

RESET Resets picture quality controls to the Bright Lighting Picture

Control Preset. Point and select to choose a different Picture Control

Preset. Also used to reset the settings in a menu.

USING THE WHO.INPUT BUTTON

Use the WHO*INPUT button to toggle through the available input
sources (VlD and the current channel) and view the component you

have connected to the TV.

1.

2.

3.

PressTV to place the remote in TV mode. Make sure that the

component you want to view is turned ON.

PressWHO,INPUT to tune to the available input source and view

the component.

PressWHO.INPUT again to tune back to the channel you were
previously watching.

Modes of Operation

Because this universal remote can control

several different components (DVD
player, VCR, cable box, etc.), it uses
operational modes triggered by the

component buttons. For example if you
want the remote to control the TV, you

would press the TV button to put the
remote into TV mode before you could

control the TV.

23

PROGRAMMING THE REMOTE

The universal remote can be programmed to control most brands of
remote controllable VCRs,satellite receivers and cable boxes. The

remote is already programmed to control most RCA, GE and PROSCAN
TVs, VCRs, DVD players, laserdisc players and satellite receivers.

TESTING THE REMOTE

To determine whether the universal remote needs to be programmed,
turn a device ON, such as a VCR, point the remote at the VCR, and press

the VCR1 button. Then press ON.OFF or CH ^ (channel up) or CH v
(channel down) to see if the VCR responds to the remote commands. If

not, the remote needs to be programmed.

PROGRAMMING THE REMOTE

Using Automatic Code Search

The following instructions can be used to program the remote to
control each of the devices connected to your TV. If you want to exit the

automatic code search without programming any of your devices, press
and hold CLEAR until the LED turns off.

1,

2.

3,

Turn on the device you want to control (VCR, SAT, etc.).
Press and hold the button you want to program (VCR1, VCR2, etc.).

While holding the device button, press and hold ON.OFF until the
red light on the remote turns on, then release both buttons.

Press and release PLAY, then wait 5 seconds or until the LED stops
flashing.

At this point the remote is searching for the correct code to
program. If, after 5 seconds, the device you want to control does
not turn off, press PLAY again to tell the remote to search the next

set of codes.
Continue pressing PLAY until the device turns off or you have

searched through all of the codes. There are 20 total sets of codes.
If the device does not turn off after pressing PLAY 20 times, then
the remote cannot control that particular device.

If the device you want to control does turn off:

1. Press and release REVERSE,then wait 2 seconds. Repeat this step
until the device turns back ON.

2. To finish, press and hold STOP until the red light on the remote
turns off.

_REWRSE

You'll use these buttons when you

program the remote to control any

device.
The remote may not operate all models

of all brands.

24

Using Direct Entry

1. Turn on the component to be programmed.

2. Look up the brand and code number(s) for the component on the
code list on the last page of this section, Using the Remote.

3. Pressand hold the button on the remote you want to program.

4. Enter the code from the code list.

5,

6,

Release button, and then press ON.OFF to see if the component
responds to the remote commands. If it doesn't, try pressing the
component button and then ON.OFF again.

If you get no response, repeat these steps using the next code listed
for your brand, until the component responds to the remote

commands.

USING THE REMOTE TO CONTROL A DEVICE

Once the remote has been programmed successfully, you are ready to

use it to control your devices. To operate the device:

1. Pressthe device button (TV, VCR1, VCR2, DVD, AUX, or SAT.CABLE)
to set the remote to control the device.

2. PressON.OFF to turn the device ON or OFF.

3. Use the remote buttons that apply to that device.

MODES OF OPERATION

Because this universal remote can control several different components
(DVD player, VCR, Cable Box, etc.) it uses operational modes triggered

by the component buttons. For example, if you want the remote to

control the TV, you would press the TV button to put the remote into TV

mode before you could control the TV.

FRONT PANEL

If you cannot locate your remote you can use the front panel of your TV

to operate many of the TV's features.
MENU Brings up the Main menu. When in the menu system, it selects

highlighted items. Also returns you to the previous menu.

CH v Scans down through the current channel list. In the menu system,

it points down to items and adjusts menu controls.

CH ^ Scans up through the channel list. In the menu system, it points

up to items and adjusts menu controls.

VOL - Decreases the volume. When in the menu system, VOL - is used
to point left to items and adjust menu controls.

VOL + Increases the volume. When in the menu system, VOL + is used
to point right to items and adjust menu controls.

POWER Turns the TV on and off.

MENU OH_ OHl_ VOL-- VOL + POWER I

The front panel above shows a typical
button layout. The exact look of the

buttons may be different from those on
the front of your TV.

The Front Panel Block feature disables all
front panel buttons if Parental Controls

are locked. For more information, see
Parental Control, in the Features and

Menus section.

]

25

'11

Admiral .........................................................................2131

Adventura .....................................................................2020

Aiko ...............................................................................2027

Aiwa ....................................................................2002, 2020

Akai ... 2003, 2004, 2005,2007, 2008, 2111,2112, 2113

American Nigh ............................................................2021

Asha ...............................................................................2013

Audio Dynamics ..............................................2009, 2010

Audiovox ......................................................................2014

Bell & Howell ...............................................................2011

Beaumark .....................................................................2013

Broksonie ..........................................................2012, 2025

Calix ..............................................................................2014

Candle. ,.... 2013, 2014, 2015, 2016, 2017, 2018, 2019

Canon ......................................................2021, 2022, 2114

Capehart ............................................................2020, 2110

Carver ...........................................................................2062

CCE ....................................................................2027, 2061

Citizen 2013, 2014, 2015, 2016, 2017, 2018,2019,2027

Colortyme ...................................................................2009

Colt ................................................................................2061

Craig .............................................2013,2014, 2023, 2061

Curtis-Mathes ...........................2000, 2002, 2009, 2013,

.................................2016, 2018, 2021, 2022, 2024, 2115

Cybernex ......................................................................2013

Daewoo .... 2015,2017, 2019,2025, 2026, 2027, 20288

Daytron .........................................................................2110

Dhx .....................................................................2009, 2010

Dimensia .......................................................................2000

Dynatech ...........................................................2002, 2026

Electrohome .....................................................2014, 2029

Eleetrophonic ..............................................................2014

Emerson .................................................2002, 2012,2014,

............2015, 2021, 2024,2025,2026,2029, 2030, 2032,

2033, 2034, 2035, 2036, 2037,2038, 2039, 2040, 2041,

2042, 2044, 2045,2047, 2065, 2105,2113, 2116, 2117,

2130

MTC ..........................................................2002, 2013, 2026

Multitech .................2002, 2013, 2016, 2026, 2053, 2061

N EC....................................2009, 201O,2011,2010, 2018,

.......................2058, 2064, 2076, 2078, 2079, 2111, 2123

Nikko ...............................................................................2014

Noblex ............................................................................2013

Olympus .........................................................................2021

Optimus ...............................................................2014, 2131

Optonica .........................................................................2096

Orion ..............................................................................2035

Paaasoaic.................2021, 2022, 2109, 2125, 2120, 2127

Pentax .................................2016, 2055, 2056, 2107, 2120

Pentex Resea)ch ...........................................................2018

Philco ..............................................2021, 2022, 2062, 2063

Philips .............................................2021, 2062, 2096, 2124

Pilot .................................................................................2014

Pioneer ................................2010, 2055,2080, 2081, 2123

Portiand .........................................2016, 20t 7,2019, 2110

P_oSc_t_ .................................................... 2000, 2001

Protec ..............................................................................2061

Pulsar...............................................................................2104

Quarter ..........................................................................2011

Quartz .............................................................................2011

Quasar ......................................................2021, 2022, 2125

RCA ....................................2000, 2001, 2003, 2013, 2021,

..............2055, 2056,2082, 2083, 2084,2085, 2086,2087,

..............2088, 2089, 2090, 2091, 2107, 2115, 2120, 2125

Radioshack/Realistic ....................2002, 2011, 2013, 2014

2021, 2022, 2023, 2026, 2029, 2049, 2050, 2096, 2131

Radix ................................................................................2014

Randex ............................................................................2014

Ricoh ...............................................................................2128

Runco ..............................................................................2104

Samsun9 ...................2005, 2013, 2015, 2033, 2053, 2112

Saaky ....................................................................2131,2104

Saasui .............................................2010, 2092, 2111, 2123

Saayo.........................................................2011,2013, 2023

Scott. 2012, 2015, 2025,2032, 2035, 2038, 2065,2093,

2116

Sears ....................................2011,2014, 2021, 2023, 2048,

Fisher• 2011, 2023, 2048,2049, 2050, 2051, 2052,2118 .........................2049, 2050, 2051, 2055, 2056, 2107, 2118

F_i ......................................................................2021,2119

Funai ...................................................................2002, 2020

Garrard .........................................................................2020

GE ... 2000,2001,2013,2021,2022,2053,2115, 2120

Goldstar ............................2009,2014,2018,2054,2121

Gradiente .....................................................................2020

Harley Davidson .........................................................2020

Harman Kardon ..........................................................2009

Harwood ......................................................................2061

Headquarter ................................................................2011

Hitachi2002,2055,2056,2057,2107,2111,2120,2122

H]-Q ..............................................................................2023

Instant Replay ..............................................................2021

JCL .................................................................................2021

JC Penney .............2009,2010,2011,2013,2014,2021,

.......... 2022,2055,2056,2058,2059,2000,2107,2118

Jensen......................................................2055,2086,2111

JVC ...............2009,2010,2011,2018,2058,2111,2123

Kenwood ..............2009 2010,2011,2016,2018,2038

2 11,212_

KLH ...............................................................................2061

Kodak .................................................................2014,2021

Lloyd ...................................................................2002,2026

Logik ..............................................................................2061

LXl .................................................................................2014

Magnavox.., 2021,2022,2062,2063,2104,2108,2124

Magnin ...........................................................................2013

Marantz ..................................................2009,2010,2011,

..................................2016,2018,2021,2058,2062,2064

Marta .............................................................................2014

Masushita ......................................................................2021

MEI .................................................................................2021

Memorex ..........................................................2002,2011,

.....................2013,2014,2021,2023,2026,2104,2131

MGA ........................................................2029,2065,2113

MGNTechnology ........................................................2013

Midland .........................................................................2053

Minolta ....................................................2055,2056,2107

Mitsubish[..2099,2055,2056,2065,2066,2067,2069,

.......... 2070,2071,2072,2073,2074,2106,2113,2123

Montgomery Ward ..........................................2075,2131

Motorola ...........................................................2021,2131

Sharp ..............2002, 2017, 2029, 2094, 2095, 2096, 2131

Shintom ..........................................2004, 2056, 2061, 2098

Shogun ............................................................................2013

Signature .............................................................2002, 2131

Singer.........................................................2021, 2061, 2128

Sony ..........................2002, 2004, 2098, 2099, 2119, 2128

STS........................................................................2021, 2107

Sylvania 2002, 2021, 2022, 2026, 2062, 2063, 2065,2124

Symphonic ...........................................................2002, 2026

Tandy ....................................................................2002, 2011

Tashiko ............................................................................2014

Tatung ...................................................................2058, 2111

TEAC ...................................2002, 2026, 2058,2085, 2111

Technics ...............................................................2021, 2109

Teknika .....................2002, 2014, 2021, 2026, 2100, 2129

TMK ...........................................................2013, 2024, 2047

Toshiba ...........2015, 2049, 2051, 2055, 2065,2093, 2116

ToteVision ...........................................................2013, 2014

Unitech ...........................................................................2013

Vector Resealch ..........................2009, 2010, 2015, 2016

Victor ..............................................................................2010

Video Concepts ................2009, 2010, 2015, 2016, 2113

Videosonic .....................................................................2013

Wards ........... 2002, 2013,2014, 2015, 2021, 2023,2026,

• 2029, 2055, 2056, 2061, 2096, 2101, 2102,2103, 2107,
2116,2131

XR-lO00 ...................................................2021, 2026, 2061

Yamaha.....................2009, 20t O,20t 1,2018, 2058, 2111

Zenith ..................................2004,2098, 2104, 2119, 2128

ABC ................5002, 5003, 5004, 5005, 5006, 5007, 5053

Antronix ..............................................................5008, 5009

Archer ............................................5008, 5009, 5010, 5011

Cahletenna .....................................................................5008

Cableview .......................................................................5008

Century ..........................................................................5011

Citizen .............................................................................5011

Colour Voice .......................................................5012, 5013

Comtronics .........................................................5014, 5015

Contec ............................................................................5016

26

Eastern ...................................................................................5017

Garrard ..................................................................................5011

GC Electronics .....................................................................5009

Gemini .............................................................5018,5019,5049

Generallnstrument ............................................................5003

Hamlin ........................................5020,5021,5022,5035,5045

Hitachi ....................................................................................5003

Hytex ......................................................................................5002

Jasco .......................................................................................5011

Jerrold .... 5003,5005,5007,5018,5023,5024,5046,5053

Magnavox ...............................................................................5025

Memorex ...............................................................................5026

MovieTime .....................................................5002,5027,5028

NSC ..................................................................5002,5027,5028

Oak ....................................................................5002,5016,5029

Panasonie....................................................................5048,5052

Paragon ..................................................................................5026

Philips ...,.. 5011,5012,5013,5019,5025,5030,5031,5032

Pioneer ........................................................................5033,5034

Pulsar......................................................................................5026

RCA ..................................................................5047,5049,5052

Realistic .......................................................................5009,5049

Regal............................................................................5022,5035

Regency .................................................................................5017

Rembrandt ............................................................................5003

Runco .....................................................................................5026

Samsung ......................................................................5014,5034

Scientific Atlanta ..................................5006,5036,5037,5038

Signal............................................................................5014,5018

Signature ................................................................................5003

SL Marx ..................................................................................5014

Sprucer ..................................................................................5052

Starcom ............................................................5007,5018,5053

Stargate .......................................................................5014,5018

Starquest ................................................................................5018

Tandy ......................................................................................5040

Teleview .................................................................................5014

Toeom ..............................................................5004,5023,5041

Toshiba...................................................................................5026

Tusa.........................................................................................5018

TV88 .......................................................................................5027

Unika ................................................................5008,5009,5011

United Artists .......................................................................5002

United Cable ........................................................................5053

Universal ...............................................5008, 5009, 5010, 5011

Videoway ...............................................................................5044

Viewstar ................................................5015,5025,5027,9040

Zenith ...............................................................5026,5050,5051

Chapparal ................................................................... 5056,5057

Drake .......................................................................... 5058,5059

GE ................................................................................ 5000,5001

Generallnstruments ..................................... 5060,5061,5062

Panasonic ............................................................................... 5075

Primestar ............................................................................... 5076

P_oScAN ................................................................... 5000,5001

RCA ............................................................................. 5000,5001

Realistic .................................................................................. 5003

Sony ........................................................................................ 5072

STS1 ........................................................................................ 5004

STS2 ........................................................................................ 5005

STS3 ........................................................................................ 5006

STS4 ........................................................................................ 5007

Toshiba ................................................................................... 5008

Toshiba ................................................................................... 5073

Uniden .................................................................................... 5009

n_l'll

(ForRCAand Dimensia brands only)

AM/FM ...................................................................................4003

Aux .........................................................................................4004

Phono .....................................................................................4005

CD ..........................................................................................4007

Tape ........................................................................................4006

GE ..........................................................................................2001

PROSCAN ................................................................ 2001

RCA ........................................................................................200t

THE MENU SYSTEM

This section explores the menus of your TV--beginning with
some information on using menus and control panels.

Each menu is then outlined and special features are detailed to
help you get the most from your TV.

2

V

I NTERACTIVE SETUP

V

V

V

V

27

MENUS AND CONTROL PANELS

Using the buttons on both the remote and front panel enable you to

access and make changes to the menus, control panels, and choice lists.

Menus and choice lists use the point and select rule to navigate, but

control panels use a variety of methods to adjust features on your TV.
The following pages detail how to use these controls to customize the

functions of your TV.

MENUS

The first menu is called the Main menu. Press MENU on the remote or on
the front panel to bring up the Main menu:

Menus take you to another menu or a control panel. There are two ways

to select a choice in a menu:

Point with the arrows and then select with MENU or OK.

Pressa number button on the remote. For example, in the Main
menu press 3 to go straight to the Screen menu.

Exiting a menu

There are three ways to exit a menu:

Point to Exit and press MENU or OK.
Press0 on the remote.

PressCLEAR. The on-screen displays are cleared from the screen and

you return to TV viewing.

CONTROL PANELS

Control panels allow you to adjust the default settings on many features
of your TV. You can choose a setting, enter a number, or adjust a level
such as tint or brightness. There are three types of control panels: sliders,
choice lists, and numeric entry.

Feel free to explore the menu system. If |
you're ever unsure where you are in the

J

menu system, or you're just plain tired of
exploring, press CLEAR to remove the
menus from the screen and start over

again.

28

Sliders

Sliders are used to make adjustments to a particular control.
To use a Slider in a menu:

1. Pressthe up or down arrow to select the slider control for the
feature you want to adjust.

2. Pressthe right or left arrow to adjust the indicator line on the slider.

Numeric Entry

A numeric entry control panel is used to enter numbers or letters.
A pointer appears underneath the column you are changing.

0w VcR_ Au× _AT. CASLE

MUTE SKIP

SOU_B GO_ACK

Arrows-- _(_

_[NU CLEAR

R_V_RS_ PLAY fOrWARD

REC'VER_ sr0P P_U_[

P_ SWAp CHC_L _ES_

OOOO

1. Use the digits to enter a number in the column above the pointer.

2. Pressthe right arrow to move to the next column, then use the
digits to enter a number.

3. When you have finished entering information, press MENU or OK.

If the control panel is not set to the

current time, use the arrows to go back
over the columns and the digits to make
changes.

You can also enter numbers by using the
up and down arrows on the remote.

]

29

CHOICE LISTS

Choice lists are used to choose a particular setting from a list. When the
choice list appears, the highlighted item is the one that is currently

selected, or "in use."

Point to a choice on a menu and press MENU or OK to select that choice.

You will then return to the previous screen.

Now that you know how to access the menus and adjust the control
panels the following pages provide a brief explanation of all the menu

features. The features are organized in order of their location on the

Main Menu.

AUDIO MENU

Mute PressOK to reduce the TV's volume to its minimum level. Press

OK again to restore the volume.
Tone Controls Displays the slider controls for adjusting the TV's treble,

bass and balance.

Audio Processor Displays a choice list of available audio modes, which
control the way the sound comes through your speakers.

Mono Plays the sound in mono only. Use this setting when
receiving broadcasts with weak stereo signals.

Stereo Splits the incoming stereo audio signal into left and right
channels. Most TV programs and recorded materials have stereo
audio. The TV displays the word STEREOwhen you tune to a

program that is broadcast in stereo.

Expanded Stereo Electronically "widens" sound from stereo

broadcasts, stereo VCRs, digital satellite systems, DVD players, and
LaserDisc players for a fuller, more spacious sound.

Sound Logic Stereo Reduces the annoying blasts in volume
during commercial breaks, and also amplifies softer sounds in

program material. Eliminates the need to constantly adjust volume

control.

Second Audio Program (SAP) Plays the program's audio in a

I Audio

30

second language, if one is available. The TV displays the word SAP
when you tune to a program that is broadcast with SAP

information. SAP audio is broadcast in mono. SAP is also used to
broadcast a program's audio with descriptions of the video for the

visually impaired.

Audio Output & Speakers Displays a choice list that lets you turn the
TV's internal speakers on or off and set the audio outputs to fixed-level

or variable control level.

Variable Output, Speakers On This setting turns the TV's speakers
on and allows variable output from the TV's audio output jacks.

Variable Output, Speakers Off This setting turns the TV's
speakers off and allows variable output from the TV's audio output

jacks.

Fixed Output, Speakers Off This setting turns the TV's speakers
off and allows fixed output from the TV's audio output jacks to an
external device such as a surround sound amplifien With Fixed
Output On, the TV's volume control, tone controls and mute are

disabled.

USING THE REMOTE TO SELECT AN

AUDIO PROCESSOR

You can change the audio processor from the Audio menu, as illustrated
above, or by pressing the SOUND button on the remote. To make a
selection using the remote:

1. PressSOUND to display the audio processor choice list.

2. Point to and select a different audio processor or press CLEAR to
exit.

button

,@3@

31

PICTURE QUALITY MENU

Basic Picture Controls Displays the five slider controls for adjusting

the way the picture looks.

Contrast AdJusts the difference between the light and dark areas
of the picture.

Color Adjusts the richness of the colon

Tint Adjusts the balance between the red and green levels.

Black Level Adjusts the brightness of the picture.
Sharpness Adjusts the crispness of edges in the picture.

When exiting this menu, the Save Personal Picture Preset choice list will
appear. You can choose either Yes or No. If you save the settings as a

Personal Picture Preset, the TV will store the settings so you can re-
select them easily if someone changes the settings.

Picture Presets Displays a choice list that lets you select one of three
preset picture settings: Bright Lighting, Normal Lighting, Soft Lighting
or Personal Picture Preset. Choose the setting that is best for your

viewing environment.

Auto Color Displays a choice list that lets you turn on the feature that
automatically corrects the color of the picture. (This is especially useful
for tracking realistic flesh tone colors as you switch from channel to
channel.) Choose On or Off, depending on your preference.

Color Warmth Displays a choice list that lets you set one of three
automatic color adjustments: Coolfor a more blue palette of picture
colors; Normal; and Warm for a more red palette of picture colors. The
warm setting corresponds to the NTSC standard of 6500°K.

I Press the RESETbutton on the remote to |

bring up the Picture Control Presets choice

J

list. Point to the desired setting, press
MENU or OK to select it,

32

SCREEN MENU

Closed-Caption Display Displays a choice list that lets you choose the
way closed captioning information is shown on the screen.

Off No captioning information is displayed.
On Captioning information is shown always, when available.
On When Sound is Muted Captioning information is shown,

when available, whenever the TV's sound is muted. (To mute the
sound, press the MUTE button.) The captioning information is not

displayed when the sound is not muted.

Closed-Caption Mode Displays a choice list that lets you choose which
captioning mode is used for displaying captioning information.

PIP Closed-Caption Display Displays a choice list that lets you choose

the way closed captioning information is shown in the PIPwindow.

Off No captioning information is displayed.
On Captioning information is shown always, when available.
Alternate with PIP button Captioning information is shown,

when available, when the PIP button is pressed and the PIPwindow

is displayed.

PIP Closed-Caption Mode Displays a choice list that lets you choose

which captioning mode is used for displaying captioning information
within the PIP window.

Menu Language Displays a choice list that lets you select your
preferred language for the menus: English, Spanish or French.

33

USING CLOSED CAPTIONING

Many programs are encoded with closed captioning information, which
lets you display the audio portion of a program as text on the TV screen.

Closed captioning is not available on all channels at all times. Only
specific programs encoded with closed captioning information are
applicable. When a program is closed captioned, the letters CC are
displayed in the channel marker. See the section Features and Controls

for more information about the channel marker.

Closed Captioning Modes

The TV offers eight closed-captioned modes, including four text modes.
To set the Closed-Captioning Mode:

1. Select Screen from the Main menu.

2. Point to Closed-Caption Mode and press OK. A choice list displays:

3. Point to your choice and press OK to select it and return to the
Screen menu.

Turning off Closed Captioning

1. Select Screen from the Main menu.

2. Press OK to select Closed-Caption Display.

3. Point to OffAIways and press OK. The closed captioning is turned

off and you are returned to the Screen menu.

I If you are unsure of the differences m

among the modes, you may prefer to

{

leave the closed captioned mode set to

CC1, which displays complete text of the
program in the primary language in your

area.

34

CHANNEL MENU

Signal Type Displays a choice list that lets you select the current
antenna type. This option does not appear when the GUIDE Plus+

system is set up.

UHFIVHF Antenna Choose this if you are currently using an off-air
antenna for TV signals.

Cable TV Choose this if you are currently using cable or a cable

box for TV signals.

Auto Channel Search Tells the TV to search automatically for all the
channels available through the antenna input. When the TV finds an

active channel, it places it in the Normal channel list; inactive channels

(weak stations or channels with no signal at all) will be removed from

the channel list. If you are using a cable box and have set up the GUIDE

Plus+ system then this option does not appear

List and Labels Displays a control panel that lets you edit your

Normal channel list and choose a six-character label for each channel.
Follow the on-screen directions to enter your channels and other

information.

Chan# Use the up and down arrows to scroll up and down
through the channels available via your antenna. You can enter the

channel number directly using the number buttons.
Normal List Only the channels included in the Normal list are

available when you scan up and down using the OH^Iv buttons. Use
the up and down arrows to indicate whether the channel number

indicated is included (Yes) or is not included (No} in the Normal

channel list.

Chan Label Use the up and down arrows to enter a six-character

label for each channel. Hold the button down to scroll quickly

through the characters. Press RESETto clear a label. The TV can

store up to 27 labels in memory.

Auto Tuning Displays a choice list that lets you set up the TV to

automatically tune to the correct input channel when you press a
component button (VCR1, DVD, VCR2, or SAT*CABLE) on the remote.

Set VCR 1 Channel Displays a choice list that lets you select the
channel that the TV tunes to when you press the VCR1 button.

Set VCR 2 Channel Displays a choice list that lets you select the
channel that the TV tunes to when you press the VCR2 button.

Set DVD Channel Displays a choice list that lets you select the
channel that the TV tunes to when you press the DVD button.

Set SATICABLE Channel Displays a choice list that lets you select
the channel that the TV tunes to when you press the SAT.CABLE

button.

35

The choices for each screen are:

Not connected Choose this if you do not have a component

connected to an antenna or video input on the back of the TV, or if
you don't want the TV to tune to a channel when the particular
component button ispressed.

Channel 2 (SATICable only) Choose this if your component is
connected to the antenna jack on the back of the TV, and you want

the TV to tune to channel 2 when you press the specified
component button. Reminder: Make sure the component's

Ch 2/3/4 switch is set to channel 2.
Channel 3 Choose this if your component is connected to the

antennajack on the back of the TV, and you want the TV to tune to
channel 3 when you press the specified component button.

Reminder: Make sure the component's Ch 3/4 switch is set to

channel 3.
Channel 4 Choose this if your component is connected to the

antennajack on the back of the TV, and you want the TV to tune to
channel 4 when you press the specified component button.

Reminder: Make sure the component's Ch 3/4 switch is set to

channel 4.
Video Input Choose this if your component is connected to the

VIDEO jack on the back of the TV and you want the TV to tune to
VlD (SVlD if you used an S-Video cable) input channel when you

press the specified component button.

TIME MENU

Sleep Timer Displays a control panel that lets you select the amount

of time you want to give the TV before it shuts itself off.
Schedule Displays a control panel that lets you set up a schedule for

turning the TV on and off automatically. Make sure to turn the
schedule On. The on-screen directions guide you through the steps

needed to set the schedule.

Set Time Displays a control panel that lets you enter the current time.
The on-screen directions guide you through the steps needed to set the

time. If your GUIDE Plus+ system is set up, it will automatically update
your time and this option will not appear.

View Warranty Clock Displays the number of hours the TV has been in
operation (up to 5 years) and the date the TV was first turned on.

OTHER MENUS

The rest of the menus--Parental Controls, GUIDE Plus+ menu, and

Setup--are also detailed in this manual. Look for the GUIDE Plus+ Gold

setup routine and the Setup menu in the section Interactive Setup.

Descriptions of how to use Parental Controls and the GUIDE Plus+ menu

are in the section Features and Controls.

36

HOW TO USE THE FEATURES AND

CONTROLS

This section introduces you to the features and controls with
which your TV is equipped. In this section, you will learn how

to use:

• The GUIDE Plus+ Gold Menu system

• PIP (Picture-In-Picture) control

• Parental controls, including V-Chip rating limits

V

V

V

V

FEATURES AND CONTROLS

V

37

GUIDE Plus+ GOLD MENU

You can access the GUIDE Plus+ Gold menu directly by pressing GUIDE on

the remote, or by pressing MENU on the remote and then selecting

GUIDE Plus+ Menu. If you press MENU on the remote, you can access

several other features the GUIDE Plus+ Gold system offers:

GUIDE Plus+ Setup Displays the GUIDE Plus+ Gold setup screen.

Setup Setting up the GUIDE Plus+ Gold system is detailed in the

Interactive Setup section of the book.
View Demo Runs the GUIDE Plus+ Gold system demonstration.

GUIDE Plus+ Label Displays the GUIDE Plus+ Gold label menu.

On Displays the station name when you change channels.
Off Disables the Label feature.

GUIDE Plus+ Auto Display Displays the GUIDE Plus+ Gold display

options.
On Automatically displays the GUIDE Plus+ Gold system when you

use the TV button on the remote to turn on the TV.
Off Disables the GUIDE Plus+ Gold system from being displayed

when you use the TV button on the remote to turn on the TV.

Continuous Demo Runs the GUIDE Plus+ Gold demonstration until it is

turned off. To end the Continuous Demo, press MENU.

The following sections tell you more about the GUIDE Plus+ Gold system,
how to use it, and how it works.

ABOUT THE GUIDE Plus+ GOLD SYSTEM

The GUIDE Plus+ Gold system is an interactive on-screen program guide

that lists TV schedules for your area and allows your TV direct control of

a cable box and VCR. You must first set up the GUIDE Plus+ Gold Menu
system in order to view it (see the Interactive Setup section for more
details).

To bring up the GUIDE Plus+ Gold screen, press GUIDE.
There are five sections to a GUIDE Plus+ Gold screen:

A row of Action buttons at the top of the screen numbered 1, 2
and 3

Program information
A row of Menu options
Channel listings
Advertising and special show information

I GUIDE PLus+ Setu

Action Program Menu

Buttons Information Options

Ad/Show Channel Listings
Information

38

GETTING IN & OUT OF THE GUIDE Plus+ GOLD
SYSTEM

To enter the GUIDE Plus+ Gold system:

PressGUIDE on the remote.

There are three ways to exit the GUIDE Plus+ Gold system:

PressOK to exit the GUIDE Plus+ Gold system and tune to the

channel highlighted in the Channel listing,

PressGUIDE to exit the GUIDE Plus+ Gold system and tune to the

channel displayed in the View window,

PressCLEAR to exit the GUIDE Plus+ Gold system and return to the

original channel.

DOWN LOAD I NG DATA

The GUIDE Plus+ Gold system is not available until it completes its first
download of program information. When the power is turned off, the

TV locates a "host channel" that carries GUIDE Plus+ Gold data
containing program schedule and channel mapping information, A

channel map is the list of stations and their respective channels.
To ensure that your first download of data is complete, you should leave

your TV off overnight. Downloads occur several times a day, The TVmust

be turned off for GUIDE Plus+ Gold data to download.

If the TV loses power or is unplugged, GUIDE Plus+ Gold program
information may be lost. When power is restored, make sure the setup

information is still correct. The GUIDE Plus+ Gold program will complete

a download at the next available time.

GUIDE

OK--

CLEAR

Bvo vcR_ Au× SAT,CABL_

GG°GG

7@8@

REVERS[ PLAY FORWARD

P_ SWAP CHCTRL R_s_r

Channel Mapping

If more than one cable company services your area, you may be
prompted with a Channel Mapping screen after the first GUIDE Plus+

Gold download. You will need to identify your cable company by
selecting the correct channel numbers for the stations in question.

Use the left and right arrows to change the channel group and
press OK when the correct channel group is highlighted.

THE DIFFERENT GUIDE Plus+ GOLD SYSTEM

MENUS

The GUIDE Plus+ Gold system offers six different options on the Menu

bar: GRID, SORT, SCHEDULE, MESSAGES, EDITOR and SETUP,To access the
Menu bar:

1. PressGUIDE to bring up the GUIDE Plus+ Gold screen,

2. Press MENU or use the up and down arrows to highlight the Menu
bar. The Grid Guide comes up by default,

3. Use the left and right arrows to access other menus.

4. PressOK, MENU, or use the down arrow to see the menu options,

I Since the program information provided 1

by the GUIDE Plus+ Gold system is based

on your locale, you will need to run
Setup again if you move.

39

GRID GUIDE

The Grid Guide appears each time you enter the GUIDE Plus+ Gold menu
system. It displays the current programming for each channel, The live

program is displayed in the video window,

Use the up and down arrows to browse channel listings and
CH ^Iv to page through. Use the right and left arrows to browse
future program listings.

To tune to a channel, highlight the program you want to view in the
channel listing and press OK. Press CLEAR to exit the GUIDE Plus+
Gold system and return to the original channel. Press GUIDE to exit
the GUIDE Plus+ Gold system and tune to the channel in the view

window.

GUIDE Plus+ Gold screens illustrated in
this book are representations of what

you are likely to see. Not all channels,

programs, and GUIDE Plus+ Gold
information depicted will be available in

your area.

New features and options can be

downloaded to the GUIDE Plus+ Gold
system, so these too are subject to

_,change.

Grid Guide

Action Buttons

I

Grid Guide Action Buttons

Action buttons will change according to where you are in the GUIDE

Plus+ Gold system. Be sure to look at the action bar before pressing the

command numbers.
When highlighting the Channel listings, the following Action buttons

are available on the bar:

Grid Guide
Menu

Selection

Watch Press 1 on the remote to place a timer in the Schedule for
the TV to turn on and tune to the program highlighted in the
Channel listing. When the TV turns on, the GUIDE Plus+ Gold system
will automatically appear with the scheduled program highlighted

and tuned in the View window.
Go To Press 2 on the remote to bring up the direct dial box and

enter the number of the channel you want. This will highlight the
channel and current program in the channel listing of the Grid
Guide. Press OK to tune to the highlighted channel. If the view
window is unlocked, you can press GUIDE to tune to the channel.

Record Press 3 on the remote to place a timer in the Schedule for
the VCR to record the program highlighted in the Channel listing. If
you have a cable box, changing channels on the TV will not cause
the cable box channel to change while recording.

The Program information window will display a confirmation when you

have successfully created a timer to watch or record. If you have selected
two programs to watch or record which begin at the same time or
overlap, you will receive a timer conflict message. The GUIDE Plus+ Gold
system will not schedule a conflicting timer, therefore you must choose

Action Button
command

numbers

&&°& &

0 ©

O©OO

40

between the two programs.
When highlighting the Channel names (the left column on the Channel

listing), the following Action button is available on the bar:

The PIP button on the remote also toggles

etween the locked and unlocked state. /

)

Lock/Unlock Press 1 to lock or unlock the video window to
either stay at one channel as you browse the GUIDE Plus+ Gold

system (lock) or change as you browse through different channels
(unlock).

Go To Press 2 on the remote to bring up the direct dial box and
enter the number of the channel you want. This will highlight the
channel and current program in the channel listing of the Grid
Guide. Press OK to tune to the highlighted channel. If the view
window is unlocked, you can press GUIDE to tune to the channel.

Sort Menu

Video Window Action Buttons

SORT

The Sort Menu lets you browse programs by category. The channel to
which you are currently tuned is displayed in the video window. To sort:

1. Press MENU on the remote to highlight the Menu bar.

2,

Use the arrows to highlight Sort. When Sort is highlighted for the
first time, the Movies category is displayed. Thereafter, the last

category used becomes the default. A listing of subcategories is
displayed below the category name.

3. Use the up and down arrows to highlight a subcategory. For

example, highlight Aft and press OK.

4,

When the listing comes up, All Movies are displayed. Use the ^ and
v arrows to browse the list one at a time. Use CH^ and CHv to

browse through the list one page at a time. You can also view the
next seven days' programming by pressing the right arrow.

5. Select MENU to return to the menu bar, or press GUIDE or CLEAR to

exit the GUIDE Plus+ Gold system.

Soft Menu

- Categories

Sort Menu Action Buttons

When viewing the results of a Sort, the following Action buttons will
appear on the bar:

Watch Press 1 on the remote to place a timer in the Schedule, and
then follow the on-line help for further options. Placing a timer in
the Schedule will cause the TV to turn on and tune to the program
highlighted in the Channel listing at the predetermined time.

Record Press 3 on the remote to set the VCR to record the
program highlighted in the Channel listing. If you have a cable box,

I Be sure that during the GUIDE Plus+ Gold |

setup you specified that you have a VCR.

J

If you do not, the RECORD option will not
be available.

41

changing TV channels will not cause the cable box channel to
change while recording.

The program information window will display a confirmation when you

have successfully created a timer to watch or record. If you have selected

two programs to watch or record which begin at the same time or
overlap, you will receive a timer conflict message. The GUIDE Plus+ Gold

system will not schedule a conflicting timer; you must choose between
the two programs.

SCHEDULE

The Schedule menu lets you create timers for either viewing or recording

programs. The GUIDE Plus+ Gold system allows one-button recording if

you have connected the IR controller to your VCR. See the .getup and

Connections section of this manual for more details on connecting the IR

controller.
To schedule a program to watch or record:

1. PressGUIDE to bring up the GUIDE Plus+ Gold system.

2. Highlight a program within the Channel listing.

3. Select Watch or Record from the Action buttons bar. The timer is

then automatically logged into the Schedule menu.

4. If you select Record, make sure to place a blank tape in the VCR.
The program information window will display a confirmation when you

have successfully created a timer to watch or record.

To remove or change the frequency (daily, once, or weekly) of a
scheduled event, access the Schedule Menu from the Menu bar.

1. PressGUIDE to bring up the GUIDE Plus+ Gold system.

2. Press MENU to highlight the Menu bar.

3. Use the arrows to highlight the Schedule menu selection.

4. Use the up and down arrows to highlight the program you want to
edit. Then use the Schedule Menu Action Buttons as described in the

next section.

Schedule Menu
Action Buttons

I

Schedule
Menu

Selection

• If you have selected two programs to

watch or record which begin at the same
time or overlap, you will receive a timer
conflict message. The GUIDE Plus+ Gold
system will not schedule a conflicting
timer, therefore you must choose between

the two programs.

Schedule Menu Action Buttons

When viewing the Schedule menu the following Action buttons will
appear on the bar:

Remove Highlight the Watch or Record timer you wish to remove
from the schedule and press 1 on the remote.

Change Highlight the Watch or Record timer you wish to change
and press 3 on the remote to toggle the frequency between the
following choices:

DAILY records the same program each day Monday through Friday.
ONCE records only on that day.

42

WEEKLY records the program each week at the same time.

MESSAGES

Occasionally you will receive messages regarding your GUIDE Plus+ Gold
system, as well as special programming information. You can access
these messages from the Message Menu on the Menu bar.

To read messages:

1. Press MENU on the remote to select the Menu bar.

2. Use the arrows to highlight the Messages menu selection.

3. Highlight the message you wish to read by using the up and down
arrows.

4.

Press INFO to display the full text of the message. If the text
continues beyond the screen, press INFO to view the next page of
text. Once you have reached the end of the message, pressing INFO
closes the expanded information and returns you to the Messages

screen.

5. Then use the Messages Menu Action Button as described in the next
section.

Messages

Action Buttons

Messages
Menu
Selection

Messages Menu Action Button

When viewing the Messages menu the following Action button will
appear on the bar:

Remove Highlight the message you wish to delete and press 1 on
the remote.

EDITOR

You may customize the channel listing by enabling or disabling the
display of certain channels. For instance, you may disable channels that

you never watch. You can restore disabled channels at a later point in
time.

1. PressGUIDE to bring up the GUIDE Plus+ Gold system.

2. Press MENU to highlight the Menu bar.

3. Use the right and left arrows to highlight the Editor menu selection.

4. Use the up and down arrows to select a channel.

Editor Menu

Action Buttons

I

Editor

- Menu
Selection

43

Then use the Editor Menu Action Buttons as described in the next section.

Editor Menu Action Buttons

While browsing the Editor menu, the following Action buttons are
available on the bar:

Cancel Press 1 on the remote to cancel any changes made since
entering the Editor Menu,

Change Press 2 on the remote to change the channel number for
the highlighted channel line.

On/Off Press 3 on the remote to toggle the state of the channel
between On and Off.

EXPANDED INFORMATION

To view more information about a program, advertisement or special,
highlight the channel listing or ad/show information box and press the

INFO button. Requesting more information about a particular show will
also display the PlusCode programming number and the Shows on Next for

that channel.
Pressing INFO while highlighting an ad panel will fill the screen with any

additional and/or promotional information regarding that particular
program.

Pressing the INFO button again exits the expanded information screen.

TROUBLESHOOTI NG

Troubles sometimes are caused by simple "faults" that you can correct
without a service technician. Here are a few basic remedies:

Program information does not download

Review your setup information and make sure it is correct.
The TV must be off to download information. Leave your TV off

overnight, for at least 10 hours, to receive a download for your area.
If you are using a cable box, make sure the cable box is on in order to

receive program information.

Scheduled Watch or Record does not occur

Check Schedule for timer conflicts.

Check that IR controllers are attached securely and directly over the
remote sensor.

Leave your VCR off to record programs.
Make sure there is a tape in the VCR and that the VCR is properly

connected.

Ad/Show Information

44

PIP (PICTURE-IN-PICTURE) OPERATION

The PIP (picture-in-picture) feature lets you display a second, smaller

picture on top of the main picture.

Your TV is equipped with a single tuner that tunes to cable or off-air
television signals. The PIP feature on your TV requires a second video

source, like a VCR or satellite receiver to supply the second picture to the
screen. The PIP feature also requires connecting the second video source
to the TV with audio/video cables.

PIP Buttons

There are four remote buttons that control the way the PIP window
works:

PIP Brings up the PIP window. Press PIPagain to remove the window.
When PIP Caption Display - Alternate with PIP- has been selected, will

display captioning in the PIP window.
MOVE buttons Let you move the PIP window to different areas of the

screen.
SWAP Switches, or "swaps," the video from the PIPwindow with the

main picture.

CH CTRL (Channel Control) Lets you switch channel control between
the PIP window and the main picture. To determine whether you are

controlling the PIPor the main picture, bring up the Channel Marker

(detailed on the following page). The yellow channel number is the one

you are controlling.

Dw wR2 _ux s_,c_,B_[

AA°A A

_,_u_ sKiP

SeUN_ COa¢,C

<I D-

J

PIP buttons

-- Move
buttons

Using the PIP Feature

While you may use PIP in different ways, this basic PIP scenario should
get you started. While watching the TV, follow these steps to use your

VCR to supply the picture for PIn

1. Pressthe PIP button on the remote. The PIP window appears on the
screen.

2. Turn on theVCR.

3.

4.

5.

Pressthe TV button, then press WHO.INPUT until you see the VCR

signal displayed in the PIPwindow. The PIP window should display
the channel that you have the VCR tuned to.

To change the program in the PIP window, you need to change the
channel on the VCR because that is the signal source for the PIP

picture. Press the VCR button on the remote to get into VCR mode,

then change channels.

Use the channel up and down buttons and the other PIP buttons,
MOVE, SWAP and CH CTRL to adjust the two pictures.

"A typical use of SWAP isto scan through

channels in the PIP window, and when
you find a channel you like, press SWAP

to display that channel in the main
picture, sending the current channel to

the PIP window.
You must change the mode between the

TV and VCR after every SWAR

}

45

PIP Problems?

Make sure the remote is in the right mode. For example, once you

turn on the VCR with the VCR1 button, you can't SWAP the pictures

until you put the remote in TV mode. Just press the TV button.

No signal or bad reception? Most VCRs and satellite receivers have
an antenna or TV button. If your cable or off-air antenna goes into
your VCR or satellite receiver, then into your TV, try pressing the
antenna or TV button on the front of the component.

Tip: If programmed to control your VCR, the ANTENNA button on
the remote acts as a TV/VCR button.

Check the connections. PIPrequires a second video source, like a
VCR or satellite receiver, connected to your TV with audio/video
cables. If you use a cable box, you may need extra equipment.
Contact your cable company for more information.

CHANNEL MARKER

There are several indicators that may come up when you press the TV,

INFO, PIP or SWAP button. This display is called the Channel Marker.

12:01 Displays the current time.

CC Displayed when Closed Captioning is available on the current
channel.

ESPN Displays the label assigned to the current channel.
60 Displays the current channel or input channel. If yellow, pressing

channel up and down changes this channel.
Mute (or Stereo) Mute is displayed when you mute the audio.

Stereo is displayed when the current channel is broadcasting in
Stereo.

SAP Displayed when the current channel is broadcasting SAP

(Second Audio Program) information.

PIPS9 (PIP Chan) Displays the current PIP channel. If yellow,

pressing channel up and down changes the PIP channel.

Locked Displayed when Parental Controls are locked.
Sleep Displayed when the Sleep Timer has been set.
00:00 Displayed to count down time left on the commercial skip

(SKIP) timer.

CABLE, CABLE BOX, OR ANTENNA

VCR 1

........... ....e,v

TV

To see a different picture in the PIP
window, you must connect another video

source, like a VCR. This connection
requires audio/video cables.

• You can program the TV to tune to a •
specific channel when you press the VCR1,

SAT,CABLE, DVD and VCR2 buttons. This

isan easy way to tune the PIP window to

the correct video input channel.
Check out the auto tuning feature in the

Interactive Setup and Using the Menus

sections.

Sample displays on a Channel Marke_

46

PARENTAL CONTROLS AND V-CH IP

The Parental Controls menu allows you to program your TV so that children
cannot see certain programs, channels, or use the front panel controls.

The first three choices in the Parental Controls menu involve software inside
your TV (dubbed V-Chip) which allows you to block TV programs and movies

based on violence, sex, or other content you may believe children should not

view. In other words, it lets you program your TV so it will not display certain

programs. Once you block programs, you or other adults are not limited to only
parent-approved programs; you can unblock programs by entering a password.

The software inside your TV comes turned "off," so if you choose not to

implement it, you can just ignore it.

When turned "on," the software reads a code that most broadcasters send with programs. That code tells the
software the program's age-based rating (TV-MA, TV-14, etc.) and content themes (Violence (V), Adult Language (L),

etc.}. If you have blocked the rating and/or content themes that the program contains, you will receive the message,
"This channel is not approved for viewing," when you turn to that particular channel. Broadcasters are not required
to provide content themes, so programs received with no content themes will only be blocked if you block their age-
based rating. You can also block out programs that have been given a rating of "Not Rated," and programs that are
considered "unrated" because no code has been sent by the broadcaster.

The TV age-based ratings and content themes you can block are listed in the table below.

Age-Based

Rating Description and Content Themes for Age-Based Ratings

Mature Audience Only. Specifically designed to be viewed by adults and may be unsuitable for

TV-MA

children under 17. It contains one or more of the following content themes: graphic violence (V),
explicit sexual activity (S}, or crude indecent language (L).

Parents Strongly Cautioned. Contains some material that many parents would find unsuitable for
children under 14. Parents are strongly urged to exercise greater care in monitoring this program and

TV-14

are cautioned against letting children under the age of 14 watch unattended. This program contains
one or more of the following content themes: intense violence (V), intense sexual situations (S),

strong coarse language (L), or intensely suggestive dialogue (D).

Parental Guidance Suggested. Contains material that parents may find unsuitable for younger
children. Many parents may want to watch it with their younger children. The program contains one

TV-PG or more of the following content themes: moderate violence (V), some sexual situations (S),

infrequent coarse language (L), or some suggestive dialogue (D).
General Audience. Most parents would find this program suitable for all ages. It contains little or no

TV-G

violence (V), no strong language (L) and little or no sexual dialogue (D) or situations (S)

Directed to Children 7 years and older. Designed for children ages 7 and above. It may be more

TV-Y7 appropriate for children who have acquired the developmental skills needed to distinguish between

make-believe and reality. Themes and elements in this program may include mild fantasy violence
(FV) or comedic violence, or may frighten children under the age of 7.

TV-Y All Children. Themes and elements in this program are designed for a young audience, including

children from ages 2-6. It is not expected to frighten younger children.

47

V-CHIP TV RATING LIMIT

The V-Chip TV Rating Limit lets you decide what TV programs can and
cannot be viewed.

To set TV programming limits:

1, Choose Parental Controls from the Main menu. If Parental Controls

have previously been locked, you must enter your password. If they are
not locked, you will get a message reminding you that your limits will

not be effective until you lock Parental Controls.

2. PressMENU to continue.

3,

4.

Highlight and select V-Chip TV Rating Limit.

Once you get to the V-Chip TV Rating Limit screen, use the arrows and
OK on your remote to change the status of a TV program rating or

content theme from Viewto Block.

The following sections give you more details about how to change the
status of TV program limits.

The Ratings Limits Screen

Below is an example of where items are located within the Rating Limits screen.

Rating Field

Lets you select from a list of age-based
ratings you can block or view.

Rating Status Field

Lets you select whether the status of the age-
based rating limit to the Ieft is View or Block.

I

Rating Settings Area

Lets you see the current block/view state of age-based ratings and
associated content. The View (V) settings are coded in green, and
the Block (B) settings are coded in red.

Content Themes

Lists the content
themes you can block

or view.

Content Status

Fields

Lets you select which

content themes to
view for the selected

rating, and whether

the status of the
content theme is

currently View (V) or

Block (B).

48

Blocking Age-Based Ratings

You can automatically block all program ratings above a specified
age-based rating level. For example, if you only want your child to

watch programs that have a TV-G rating and lower (in other words,
you want the child to watch TV-G, TV-YT, and TV-Y), then you need to

block out other programming with higher ratings.

To block programs with higher ratings:

1. First, determine the lowest level rating you do not want the child
to watch.

2.

3.

Use the left and right arrows to highlight the Rating Field.
Use the up and down arrows on the remote to scroll through the

age-based rating limits. Keep scrolling until the rating
corresponding with the lowest rating you do not want the child
to watch appears.

In the example discussed above, you would scroll through the

rating field until TV-PG appears, since the highest rating you
want the child to watch is TV-G.

4. Use the right arrow to move the yellow highlight to the rating
status field.

5. Press the up or down arrow to toggle between View and Block.
The status for the rating listed to the left and all higher ratings
automatically changes to Block (and B).

Rating status field

Rating
field

Content status fields

hen you change the status of a rating to

ck, the system will automatically block |

gher ratings and all corresponding content _

emes. )

Hierarchy of

Age-Based Ratings

TV-MA Mature Audience

Only

TV-14 Parents Strongly

Cautioned

TV-PG Parental Guidance

Suggested

TV-G General Audience

TV-Y7 Directed to Children

7 years and older

TV-Y All Children

I ressing RESETon the remote will reset

all ratings to View and V.

J

6.

7.

Press MENU or OK on the remote to return to the menu or exit
the screen when you are finished.

Select Lock Parental Controls from the Parental Controls menu.

Enter a password, and if you have not already set your password,

you will be prompted to enter it again to confirm.

49

Viewing Age-Based Ratings

After you block age-based ratings, you have the option of changing
some of the ratings back to View.

1. Determine which blocked rating you want to view.

2. Use the left and right arrows to highlight the Rating Field.

3. Use the up and down arrows to select the rating whose status is

Block.

4. Press the right arrow to move the yellow highlight to the rating
status field.

5. Press the up or down arrows to toggle between View and Block.

Note that the content status fields corresponding to the unblocked
rating become Viewas well. They and the age-based rating status
are the only fields that automatically change back to Viewwhen
you complete this process.

Rating
field

Rating status field

Content

- status

fields

I ou must remember to Lock Parental 1

Controls for rating limits to take
effect.

Blocking Specific Content Themes

You can block programs based on their content. (Content is
represented by the D, L, S, V, and FV on your screen. See the

beginning of this section for details.) When you block a content
theme for a particular rating, you automatically block that content

theme for higher rated programs as well.

For example, if you do not want your child to watch programs that

have adult language (L) rated TV-PG or higher, then you could block
out all programming TV-PG and above containing adult language.

To block program content:

1. Determine the lowest level of content you do not want the
child to watch.

2.

3.

4.

5.

Use the left and right arrows to highlight the Rating Field.
Use the up and down arrows on the remote to scroll through

the age-based ratings until the rating that corresponds with the

lowest content you do not want the child to watch appears. (In
the example above, you would scroll through the ratings until
the TV-PG rating appeared.)

Press the right arrow to move the highlight to the field
corresponding with the content theme you wish to block out.

Press the up or down arrow to change content status from Vto

B. All higher ratings' content theme will automatically change
to B.

Content Themes

D Sexually Explicit Dialogue

L Adult Language

S Sexual Situations

V Violence

FV Fantasy Violence

• ]

Broadcasters am not requ=red to

provide content themes or age-based
ratings. Programs received with no
content themes will only be blocked if

kyou block their age-based rating.

50

Rating
field

Rating status field

Content themes

IcYOUmust remember to Lock Parental 1

ontrols for rating limits to take effect. |

6. Press MENU or OK to return to the menu or exit the screen.

Viewing Specific Content Themes

If you block specific content themes, you have the option of going

back and changing some of the content themes back to View (V):

1. Determine the content themes you want to change to View (V).

2. Use the left and right arrows to highlight the Rating Field.

3. Use the up and down arrows to scroll through the age-based
ratings until the rating whose content theme you want to
change to View appears.

4. Press the right arrow to move the yellow highlight to a
particular content theme status, such as the B under language
(L) corresponding with TV-14.

5.

Press the up or down arrows to change its status back to IZ Your
child would then be able to watch programs with TV-14 adult

language content, but not programs with TV-PG or TV-MA
language content.

Rating status field

Pressing RESETon the remote will reset

II ratings to View and V. J

Rating

Content themes

Note that only the content theme status corresponding to TV-14
language (L) changes to View (V). Higher rated content themes, such

as that for TV-MA language, do not change.

51

V-CHIP MOVIE RATING LIMIT

You set movie rating limits by blocking movies rated above a specified level.

Blocking Movie Ratings

If you only want your child to watch movies that have a PG rating and lower
(in other words, movies rated PG and G), then you could automatically block

out all other movies with higher ratings.
To block movies:

1.

2.

Highlight the rating field and press the up and down arrows to find the
rating that is the lowest rating you do not want the child to watch. (In

the example above, you would point to the rating status button
corresponding to PG-13, since the highest rating you want the child to
watch is PG.)

Use the right arrow to highlight the rating status field. Press the up and
down arrows to change the button from Viewto Block. All higher

ratings' Viewbuttons will automatically change to Block.

Rating field Rating status field

Some movies may be given a Not Rated_
(NR) rating. After blocking movie |

ratings, you must set NR to View |
separately to view NR movies. )

3. Press OK to return to the menu or exit the screen.

4. If Parental Controls are not locked, you must lock them so the movie
rating limits will take effect. See the section Locking Parental Controls.

Viewing Movie Ratings

After you block movie ratings, you have the option of changing some of the
rating status buttons back to View:

1. Highlight the rating field and press the up and down arrows to find the
rating you want to view.

2. Use the right arrow to highlight the rating status field. Press the up and
down arrows to change the button from Blockto View.

For example, if movies with a rating of PG-13 and higher are blocked, you
can change the rating status button corresponding with NC-17. Your child
would then be able to watch all movies with a G, PG, and NC-17 rating.

3. Press MENU or OK to exit the screen, and be sure parental controls are
locked (see the section Locking Parental Controls).

You must remember to Lock Parental
Controls for rating limits to take effect. |

J

Rating field Rating status field

52

V-CHIP UNRATED PROGRAM BLOCK

Selecting this option lets you decide if programs that the V-Chip
recognizes as "unrated" can be viewed. Note that "unrated" TV

programs may include news, sports, political, religious, local and

weather programs, emergency bulletins, public announcements, and

programs without ratings.

View All unrated programs are available.
Block All unrated programs are not available.

Don't forget to lock parental controls after you change the status of
unrated program viewing. If you do not, the limit will not take effect.

CHANNEL BLOCK

Selecting this option lets you decide what channels can be viewed.

View Makes the selected channel viewable.
Block The front panel CH (channel) buttons will tune only to

channels that you have marked as View. The remote will still tune to
the blocked channel if you use the digits to access the channel, but

the channel will be blocked.

Don't forget to lock parental controls after you change the status of

Channel Block. If you do not, the channel block will not take effect.

FRONT PANEL BLOCK

Selecting this option lets you block (disable) or unblock (enable) the TV's
front panel. The remote still tunes to any channel. Front Panel Block can

keep children from watching TV when the parent is not present and
keep small children from playing with the buttons.

(When using this as a Parental Control method, you should remove

access to any remote capable of controlling the front panel while you

have the front panel blocked.)
Don't forget to lock parental controls after you change the status. If you

do not, the front panel block will not take effect.

LOCK/UNLOCK PARENTAL CONTROLS

Selecting this option lets you lock and unlock parental controls settings

using a password.

If you do not lock parental controls, none of the settings for V-

Chip, Channel Block, or Front Panel Block will take effect.

If you forget your password, press and hold TV on the remote and the
MENU button on the television simultaneously for 3 seconds. Parental

controls will then unlock and you can re-enter a password via Lock

Parental Controls.

53

TROUBLESHOOTING

Troubles sometimes are caused by simple "faults" that you can correct without the help of a service technician. If you
experience any difficulty with your TV, check a few basic remedies before calling your service technician.

TV will not turn on

Check to make sure it is plugged in.
Check the wall receptacle (or extension cord) to make sure it is "live" by plugging in something else.

Maybe batteries in remote control are "dead."
Maybe remote control is not aimed at remote sensor.

The front panel controls may be locked (disabled). Use the remote control to unlock the front panel controls by
selecting the Front Panel Block in the Parental Controls menu and choosing View.

Controls don't work

If using remote control, make sure remote is in TV mode by first pressing TV button.
The front panel controls may be locked (disabled). Use the remote control to unlock the front panel controls by

selecting the Front Panel Block in the Parental Controls menu and choosing View.

Try unplugging set for two minutes and then plug it back in and turn it on again.

Problems with remote

Maybe something is between the remote and the remote sensor.
Maybe the remote is not aimed directly at the component (TV or VCR) you are trying to control.

Maybe remote is not in TV Mode. Pressthe TV button so remote will control TV.
Maybe batteries in remote are weak, dead or installed incorrectly. Try replacing batteries. (Note, if you remove the

batteries, you may have to reprogram the remote to control other components.)
Remove batteries and hold number 1 for at least 60 seconds to drain the microprocessor inside the remote. Release

number 1, replace the batteries, and (if necessary) reprogram the remote.

Guide comes on when I turn on TV

The GUIDE Plus+ Gold system automatically comes up when you use the TV button on the remote to turn on the TV.
You can turn off this feature by selecting GUIDE Plus+ Auto Display from the GUIDE Plus÷ Menu, and setting it to Oft.

Turns off while playing

Scheduled Off function may have been activated.
Electronic protection circuit may have been activated because of a power surge. Wait 30 seconds and then turn on

again. If this happens frequently, the voltage in your house may be abnormally high or low.

TV turns on unexpectedly

Scheduled On or Watch from the GUIDE Plus+ Gold system may have been activated.

Blank screen

Maybe the component connected to the input jacks is not turned on.
Try another channel.

Press RESET,in case the picture controls are set too low.

No sound, picture okay

Maybe sound is muted. Try pressing volume up button to restore sound.
Maybe speakers are turned off. Check the Audio Output and Speakers control panel in the Audio menu.

If using an S-VHS component, remember to also connect the component's L and R AUDIO OUT jacks to the TV's L and R
INPUT jacks.

54

Not receiving all cable channels

Make sure you have set up the GUIDE Plus+ Gold menu to recognize your cable box. Select GUIDEPlus÷ Menu from the
Main menu, then select Setup from the GUIDE Plus+ menu. Choose "Yes" when asked if you have a cable box. Then

select Setup from the Main menu and make sure to search for all channels when prompted.

Can't select certain channel

Channel may be blocked or not approved in the Parental Controls menu.

If using a VCR, check to make sure the TV/VCR button on the VCR is in the correct "mode."

Noisy stereo reception

May be a weak station. Use SOUND button to change to mono mode instead of stereo.

No picture, no sound but TV is on

Maybe the cable/air setting is set to the wrong position. To fix, select GUIDE Plus+ Menu from the Main menu, select

the Setup option, and provide the correct information on the following screens.

Maybe a vacant channel is tuned.
If watching VCR (connected only through antenna input), make sure TV is tuned to channel 3 or 4--the same as CH3/4

switch on VCR. Also check to make sure the TV/VCR button on the VCR is in the correct "mode."

Sound okay, picture poor

Check antenna connections.
Try adjusting sharpness function to improve weak signals.

Black box appears on the screen

Captioning may be turned on. Check the Closed-Caption Display control panel in the Channel menu.

GUIDE Plus+ Gold IR controllers not working

Check to make sure the controllers are positioned correctly over the IR remote sensors.
Your remote may be interfering with the IR controller. Place a piece of dark tape over the IR controller.
GUIDE Plus+ Gold system control of cable box is slower than direct control of the box when changing channels.

CARE AND CLEANING

CAUTION: Turn OFF your TV before cleaning.

You can clean the TV as required, using a soft lint-free cloth. Be sure to occasionally dust the ventilation slots in the cabinet
to help assure adequate ventilation.

The TV's screen may be cleaned with a soft, lint-free cloth as well. Take care not to scratch or mar the screen. If
necessary, you may use a cloth dampened with warm water. \

Never use strong cleaning agents, such as ammonia-based cleaners, or abrasive powder. These types of
cleaners will damage the TV.

While cleaning do not spray liquid directly on the screen, or allow liquid to run down the screen and inside the TV. Also,
avoid placing drinks or vases with water on top of the TV. This could increase the risk of fire or shock hazard or damage to

the TV.

I Caution: If fixed (non-moving) images are left on the screen for long periods, they may be permanently imprinted on the

screen. Such images include network Iogos, phone numbers, and video games. This damage is not covered by your

J

warranty. Extended viewing of channels displaying these images should be avoided.

55

RCA TV LI MITED WARRANTY

What your warranty covers:

Any defect in materials or workmanship.

For how long after your purchase:

One year for labor charges.
One year for parts.
Two years for the picture tubes.

The warranty period for rental units begins with the first rental or 45 days from date of shipment to
the rental firm, whichever comes first.

What we will do:

Pay any Authorized RCA Television Service Center the labor charges to repair your television.
Pay any Authorized RCA Television Service Center for the new or, at our option, refurbished

replacement parts and picture tubes required to repair your television.

How you get service:

For screen sizes of 26" and smaller: Take your RCA television to any Authorized RCA Television

Service Center and pick up when repairs are complete.

For screen sizes larger than 26": Request home service from any Authorized RCA Television
Service Center, provided that your television is located within the geographic territory covered by
an Authorized RCA Television Service Center. If not, you must take your television to the Service
Center location at your own expense, or pay for the cost the Service Center may charge to
transport your television to and from your home.

To identify your nearest Authorized RCA Television Service Center, ask your dealer, look in the
Yellow Pages, or call 1-800-336-1900.

Show the Authorized Service Center Representative your sales receipt or other evidence of

purchase date or first rental.

What your warranty does not cover:

Customer instruction. (Your Owner's Manual clearly describes how to install, adjust, and operate
your television. Any additional information should be obtained from your dealer).

56

Installation and related adjustments.

Signal reception problems not caused by your television.

Damage from misuse or neglect.
Batteries.

Images burnt onto the screen.

A television that has been modified or incorporated into other products or is used for institutional or

other commercial purposes.

A television purchased or serviced outside the U.S.A.

Acts of God, such as but not limited to lightning damage.

Product Registration:

Please complete and mail the Product Registration Card packed with your TV. It will make it easier to

contact you should it ever be necessary. The return of the card is not required for warranty coverage.

How state law relates to this warranty:

This warranty gives you specific legal rights, and you also may have other rights that vary from state to

state.

If you purchased your television outside the United States:

This warranty does not apply. Contact your dealer for warranty information.

57

Accessory Information

Antenna (or cable-TV) connections are made with
either coaxial antenna cable or twin-lead cable.

Coaxial cables are shielded so they are less susceptible
to hum or interference from adjacent cables.

Most audio/video connections between components
can be made with shielded audio and video cables

that have RCA-type phono connectors.

m

Round 75-ohm coaxial cable

Push-on Connector

Screw-on Coaxial

Connector

Flat 300-ohm twin-lead cable

The following accessories are available from most dealers and
electronics supply stores in case you want to position your
components farther apart or need additional cables.

Antenna Cables

VH81 (3-ft)
VH82 (6-ft)

VH89 (6-ft)

Screw-on Cable attaches to
the round antenna connectors

(called 75-ohm F-type) on the
back of your VCR or TV. The

ends screw onto the connectors
for a secure connection.

Push-on Cable attaches to the
round antenna connectors

(called 75-ohm F-type) on the
back of your VCR or TV. Ends

push on for a quick connection.

Standard Audio/Video cable with RCA-type
phono plugs (such as No. VH83)

Color-Coded Jacks

The jacks on the TV's monitor panel are color-coded
for ease of use. The video jacks are yellow, the right

audio jacks are red, and the left audio jacks are white.
When connecting components to each other, be sure
that you always connect left outputs to left inputs and

right outputs to right inputs. If a component has only
one output (mono), connect it to the r/mono input

jack.

To connect S-VHS (Super-VHS) components, an
S-VHS video cable is required.

S-Video cable (such as No. VH913)

Gold-Plated Jacks and Gold-Tipped Cables

Gold plating helps prevent oxidation of contacts which
provides much less loss than conventional contacts. A

complete line of gold-tipped cables is available to help
you obtain optimum performance from your equipment.

Audio/Video Cables

Gold-Tipped cable
VH83 (6-ft)

Monaural VCR Dubbing

Cable Double cable that lets

you connect the video and
audio jacks of two VHS VCRs to

duplicate tapes. Can also be
used to connect a VCR to your

TV. Cable is color-coded and
shielded. Has RCA-type phono

plugs on each end.

Stereo VCR Dubbing Cable

Triple cable that lets you
connect the VIDEO and AUDIO

jacks of stereo components.

Gold-Tipped cable
VH84 (6-ft)

VH976 (6-ft)
VH913 (12-ft)

S-Video Cable has multi-pin
connectors on each end for

connecting S-Video components
to your TV.

58

Q@
Q,Q

CRK76TA1

Splitter
VH47

ANT200

Remote Control This is
the remote control that

came packed with your TV.

Replacements or spares

can be ordered as needed.

2-way Signal Splitter

helps you connect to a

second TV or VCR.

Amplified VHFIUHFIFM
Antenna allows you to

easily switch from the
antenna signal to cable or

satellite easily without
disconnecting antenna,

-p

Accessory Order Form

Description

Screw-on antenna cable (3-ft)

;crew-on antenna cable (6-ft) VH82

>ush-on antenna cable (6-ft) VH89

VIonaural VCR Dubbing Cable (6-ft) VH83

;tereo VCR Dubbing Cable (6-ft) VH84
;-Video Cable (6-ft) VH976
;-Video Cable (12-ft) VH913

__-waySignal Splitter VH47
a,mplified Antenna ANT200

a,ntenna Mixer 193984

_emote Control (CRK76TA1) 240896

a,udio-Video Adapter 228449

$6.95

$5.95
$5.95
$9.95

$7.95
$8.95

$3.95

$49.95
$10.95

$39.95

$4.35

Prices are subject to change without notice.

Total Merchandise ............................................ $

Sales Tax .............................................................. $__

We are required by law to collect the
appropriate sales tax for each individual

state, country, and locality to which the
merchandise is being sent.

Shipping and Handling ..................................... $ 5oo

Total Amount Enclosed ..................................... $-_

Use VISA, MasterCard, or Discover Card

_referably.

Money order or check must be in U.S.
currency only.

No COD or CASH.

All accessories are subject to availability.
Where applicable, we will ship a superseding model.

59

Charge your order on your VISA,

MasterCard, or Discover Card by

filling in below

USE YOUR CREDIT CARD

IMPORTANT: (opy COlZapleteaccount lmmber

from your VISA card

VISA

7T-T-TqTTTq TTTq TT-rq

Mycardexpires: _

IMPORTANT: (opy COlZapleteaccount lmmber

from your Master( ard

V-F-V_ V-VT-_ V-VT-_ V-VT-_

Cop,Numb0_V-I--V-V-1 M,_aldI I II I I

above your expires:

nalzae Oll

MasterCard

IMPORTANT: (opy complete account number

froITl your Discover (ard

V-F-V_ V-VT-_ V-VT-_ V-VT-_

My card expires: Elm] Elm]

AUTHORIZED SIGNATURE

(Credit card order will not be processed without signature)

Prices are subject to change without notice.

Print or type your name and
address clearly. This will be

our mailing label.

A complete and correct
order will save you days

of waiting.

Name:

Street:

Apt:

City:

State: Zip:

.... -I

Please make sure that both sides of this ibrm
have been filled out completely,

• Allow 4 weeks for delivery,

• All accessories are subject to availability,

• Prices are subject to change

Placing an Order

To place your order by phone, have your Visa, MasterCard
or Discover Card ready and call the toll-free number listed

below between 8AM and 8PM (EST) Monday through Friday

or between 9AM and 5PM (EST)Saturday.

Use this number only to place an order for accessory items
listed on this order form.

1-800-338-0376

To place your order by mail, detach and mail the completed
order form with credit card information, money order or
check in US currency (made payable to Thomson Consumer

Electronics, Inc.) to the following address:

Video Accessories

PO Box 8419
Ronks, PA 17573

60

A

Accessories 58
Advanced connections 4, 6
Age-Based Ratings 47

Audio menu 30
Audio Output 6

Audio Output Volume &

Speakers 31

Audio Processor 30
Audio/Video cables 7

Auto Channel Search 13, 35
Auto Color 32

Auto Tuning 17, 18, 19, 35

DVDChannel 18, 35

SAT/CableChannel 19, 35
VCR1Channel 17, 35

VCR2Channel 17, 35

B

Back of the TV 6
Basic Connection 4, 5

Basic Picture Controls 32
Batteries 10, 54

Black Level 32
Buttons

Remote 22

C

Cable/Antenna 6
Cables

Coaxial 4, 5

Care and Cleaning 55
CC 46
Chan # 35

Chan Labels 35
Channel

Mapping 39

Channel 3 36
Channel 4 36
Channel Block 53

Channel Map 39
channel map 39

Channel Marker 46
Channel menu 35

Channel search 13
Channels

Labeling 20

CLEAR button 12, 23
Closed Caption

Display 33
Mode 33, 34

PIPDisplay 33
PIPMode 33

Coaxial Cable 4, 5, 7

Color 32
Color Warmth 32
Connections 4

Advanced 4, 6

Basic4, 5

TV and stereo VCR 7
TV Only 4

TV,VCRand Sateilite Receiver 8

Content Themes 47
Contrast 32

Control Panels 28

D

DVD Channel 18, 35

F

Fixed images 55
Fixed Output, SpeakersOff

31

Front panel buttons 25
Front Panel Block 53

G

Grid Guide 40
Guide Plus+ Gold System 14,

39

Downloading information 39
Editing 43

Menu 38
Messages 43

Schedule 42
Setting up the Guide 14

Sort menus 41

Interactive Setup 12
IR Controller

Attaching to other components 9

Locating IR sensors on your

components 9

L

Labels 20, 35
Language 13, 33

Languages

Selecting 13

List & Labels 20, 35

Locating IR sensors 9

M

Main Menu 28
Memory 35

MENU button 12
Menu Language 13, 33

Menus 28, 38
Messages 43

Mono 30
Mute 30, 46

N

Normal List 35

Parental Controls

Channel Block 53
Channel biokc 53

Front Panel Block 53
Front Panel Lockout 53

Locking, unlocking 53
Menu 47

Parental Controls menu 47
Picture Presets 32

Picture Quality menu 32

PIP 4, 46

PIP (Picture in Picture)

Buttons 45

Closed caption display 33
Closed caption mode 33

PIPChan 46
Problems 46

Using 45

Point 12

Point and Select 12

R

Rating Limits

Movie 52

TV 48

Remote Control

Installing the batteries 10
Programming 24
Remote batteries are low 46

S

S-Video 6
S-Video Cable 7
SAP 46

SAT/Cable Channel 19, 35
Schedule 36, 42

Screen menu 33
Second Audio Program (SAP)

30, 46

Select 12

Set

DVDChannel 18, 35

SAT/CABLEChannel 19, 35

VCR1Channel 17, 35
VCR2Channel 17, 35

Set Time 36, 16
Setup 12

Sharpness 32
Signal Type

Cable TV 35

UHHVHFAntenna 35

Sleep 46
Sleep Timer 36, 46

Stereo 30, 46

T

Time

Current 46

Set Time 16, 36
Time menu 36
Tint 32

Tone Controls 30
Troubleshooting 54, 46

TV GUIDE Plus+ 15, 38,

41, 42, 43

Channel Mapping 39

Editor 43

Messages 43

ScheduleMenu 42

Sort Menu 41

TV only connection 4

U

UHF/VHF Antenna 35

V

V-Chip

Age-BasedRatings 47

Blocking Movies 52

Content themes 47
Variable Output, Speakers

Off 31

Variable Output, Speakers

On 31

VCR control 6
VCR1 Channel 17, 35

VCR2 Channel 17, 35
View Warranty Clock 36

61

Please do not send any products to the Indianapolis address listed in this manual or on the carton. This will only add delays in

service for your product.

The following materials were used in

printing this publication:

_._"n.IOMSONCONSUMER ELECTRONICS

10330 North Meridian Street
Indianapolis, IN 46290

@1998 Thomson Consumer Electronics, Inc.

Trademark(s)® Registered

Marca(s) Registrada(s)
Printed in USA

100%

RECYCLEDPAPER
MINIMUM40%POSTCONSIJMER

_j PRINTED WITHI

I SOYINK M

TOCOM 15455160