Television
User's Guude
Changing Entertainment. Again.
WARNING
To reduce the risk of fire or
electric shock, do not expose
this TV to rain or moisture.
kVlVl-qN_I1_[_
RISK OF ELECTRICSHOCK
DO NOT OPEN
To reduce the risk of electric shock, do not remove
cover (or back). No user serviceable parts inside.
Refer servicing to qualified service personnel.
_i his symbol indicates
"dangerous voltage" inside
the product that presents a
risk of electric shock or
personal injury.
This symbol indicates
important instructions
accompanying the product.
Caution: To prevent electric shock, match wide blade of
plug to wide slot, fully insert.
Attention: Pour eviter les chocs electriques, introduire
la lame la plus large de la fiche dans la borne
correspondante de la prise et pousser jusq0 au fond.
Refer to the identification/rating label located on the back panel of your
product for its proper operating voltage.
FCCRegulations state that unauthorized changes or modifications to this
equipment may void the user's authority to operate it.
If fixed (non-moving) images are left on the screen for long periods,
they may be permanently imprinted on the picture tube. Such
images include network Iogos, phone numbers, and video games.
This damage is not covered by your warranty. Extended viewing of
channels displaying these images should be avoided.
Cable TV Installer: This reminder is provided to call your attention to
Article 820-40 of the National Electrical Code (Section 54 of the Canadian
Electrical Code, Part 1) which provides guidelines for proper grounding and,
in particular, specifies that the cable ground shall be connected to the
grounding system of the building as close to the point of cable entry as
practical.
Product Registration
Please fill out the product registration card and return it immediately. Returning the card allows us to contact
you if needed.
Keep your sales receipt to obtain warranty parts and service and for proof of purchase. Attach it here and record
the serial and model numbers in case you need them. The numbers are located on the back of the television.
Model No.
Serial No.
Purchase Date:
Dealer/Add ress/Phone:
G-LINK, VCR Plus+, C3,PlusCode, GUIDE Plus+, and GUIDE Plus+ Gold are trademarks of Gemstar Development
Corporation.
The GUIDE Plus+ Gold system is manufactured under license from Index Systems Inc.
Thomson Consumer Electronics and Gemstar are not in any way liable for the accuracy of the program information
provided by the GUIDE Plus+ System. In no event shall Thomson Consumer Electronics or Gemstar be liable for any
amount representing loss of profits, loss of business, or indirect, special, or consequential damages in connection
with the provision or use of any information equipment, or services relating to the GUIDE Plus+ System.
Intr@duct @n
Key Features Overview
Your TV is equipped with features that will ad to your TV watching experience. The following
information summarizes a few of these features. Chapter 2 provides more information about the
rest of the TV's features and how to use them.
On-screen Program Guide
Description: The GUIDE Plus+ system is an on-screen interactive list of
programs and information that is built into your TV. You can scroll through the
guide to see what's on and tune directly to that program from the guide. You
can also browse programs by category with the sort feature.
When you access the News feature, MSNBC will appear in your video window if
it's available through your TV.
One-Touch VCR Recording is another benefit of the GUIDE Plus+ system. You
don't have to remember to program your VCR or use the menus in your VCR to
set up a recording.
Requirements:
• Remove the Demo Pin from the G-LINK jack.
• Complete the on-screen interactive setup. You'll find detailed instructions in
Chapter 1.
• One-Touch VCR Recording: You must connect the G-LINK cable to the TV
and place one of the wands in front of the remote sensor on the VCR.
• If you have a cable box, connect the G-LINK cable to the TV and place one
of the wands in front of the remote sensor on the cable box.
V-Chip: Parental Controls
Description: You can block programs and movies by content, age-based
ratings, and/or movie ratings.
Requirements:
• Set up the Parental Controls menu in the TV's main menu (Chapter 2 has
details).
• The broadcasters must use the rating system when they send the program to
your TV in order for your TV to [)lock the program.
Jntr@duct_@n
(This page intentionally left blank)
2
of
Introduction
Key Features Overview .................................................................................................... 1
On-screen Program Guide ......................................................................................... 1
V-Chip: Parental Controls ........................................................................................... 1
Chapter 1" Connections & Setup
Things to Consider Before You Connect ......................................................................... 6
Protect Against Power Surges ................................................................................... 6
Protect Components from Overheating ................................................................... 6
Position Cables Properly to Avoid Audio Interference ............................................ 6
Important Stand and Base Safety Information ........................................................ 6
Use Indirect Light ....................................................................................................... 6
Demo Pin .................................................................................................................... 6
Choose Your Connection .................................................................................................. 7
Cables Needed to Connect Components to Your -IV ............................................... 7
Connection: TV + VCR ....................................................................................................... 8
Connection: TV Only ......................................................................................................... 9
Connection: TV + VCR + Satellite Receiver ................................................................... 11
The Front of Your TV ...................................................................................................... 12
Why You Should Connect This G-LINK Cable ............................................................... 13
How to Find the Remote Sensor ............................................................................. 13
Placing the G-LINK Wands ....................................................................................... 13
Complete the Interactive Setup ..................................................................................... 15
Set the Menu Language .......................................................................................... 15
Complete Auto Channel Search .............................................................................. 15
The GUIDE Plus+ System Setup ................................................................................ 15
What to Expect ............................................................................................................... 19
The Buttons on the Remote Control ............................................................................. 20
Chapter 2: Using the TV's Features
About the GUIDE Plus+ System ..................................................................................... 22
Downloading Data ................................................................................................... 22
Getting In & Out of the GUIDE Plus+ System ......................................................... 23
The GUIDE Plus+ System Menus .............................................................................. 23
Grid Guide ................................................................................................................ 23
Sort ............................................................................................................................ 25
News .......................................................................................................................... 26
Schedule .................................................................................................................... 26
Messages ................................................................................................................... 27
Channels ................................................................................................................... 28
Setup ......................................................................................................................... 28
How to Get More Information About an Advertisement or a Program ............... 29
GUIDE Plus+ Menu Items ............................................................................................... 29
Channel Banner .............................................................................................................. 30
Parental Controls and V-Chip ......................................................................................... 30
How V-Chip Works ................................................................................................... 31
V-Chip TV Rating Limit ............................................................................................. 32
3
@f C@nt nts
Blocking Specific Content Themes .......................................................................... 34
Viewing Specific Content Themes ........................................................................... 35
V-Chip Movie Rating Limit ....................................................................................... 35
V-Chip Unrated Program Block ............................................................................... 37
Channel Block ........................................................................................................... 37
Front Panel Block ..................................................................................................... 37
Lock/Unlock Parental Controls ................................................................................ 38
Chapter 3: Using the TV's Menu System
How to Use the Different Types of Menus and Control Panels .................................. 40
Menus ....................................................................................................................... 40
Control Panels .......................................................................................................... 40
Picture Quality Menu ..................................................................................................... 42
Screen Menu ................................................................................................................... 42
Using Closed Captioning ................................................................................................ 43
Channel Menu ................................................................................................................. 44
Time Menu ...................................................................................................................... 44
Chapter 4: Other Information
Troubleshooting .............................................................................................................. 46
Care and Cleaning .......................................................................................................... 49
RCATV Limited Warranty .............................................................................................. 49
Index ................................................................................................................................ 53
4
Connections & Setup
Chapter Overview:
• Things to Consider Before You Connect
• Choose Your Connection
• Connections
• The Front of Your TV
• Why You Should Connect This G-LINK Cable
• Plug in theTV
• Put Batteries in the Remote
How to Use the Remote Control to Complete the
Interactive Setup
Turn on the TV
• Complete the Interactive Setup
• Buttons on the Remote Control
Changing Entertainment. Again.
5
C@nn ct @ns N tup
Things to Consider Before You Connect
Protect Against Power Surges
• Connect all components before you plug any of their power cords into the wall outlet.
• Turn off the TV and/or component before you connect or disconnect any cables.
• Make sure all antennas and cables are properly grounded. Refer to the Important
Safeguards sheet packed with your TV.
Protect Components from Overheating
• Don't block ventilation holes on any of the components. Arrange the components so that
air can circulate freely.
• Don't stack components.
• When you place components in a stand, make sure you allow adequate ventilation.
• If you connect an audio receiver or amplifier, place it on the top shelf so the heated air
from it won't flow around other components.
Position Cables Properly to Avoid Audio Interference
• Insert each cable firmly into the designated jack.
• If you place components above the TV, route all cables down the side of the back of the
TV instead of straight down the middle of the back of the TV.
• If your antenna uses 300-ohm twin lead cables, do not coil the cables. Also, keep the twin
lead cables away from audio/video cables.
Important Stand and Base Safety Information
Choose the location for your TV carefully. Place the TV on a stand or base that is of adequate
size and strength to prevent the TV from being accidentally tipped over, pushed off, or pulled
off. This could cause personal injury and/or damage the TV. Refer to the Important Safeguards
sheet packed with your TV.
Use Indirect Light
Don't place the TV where sunlight or room lighting will be directed toward the screen. Use soft
or indirect lighting.
Demo Pin
You must remove the Demo Pin from the G-LINK jack on the back of
your TV in order for your TV to operate properly and to connect the
G-LINK cable.
6 Chapter I
C@nn cti@ns S tup
Choose Your Connection
There are several ways to connect your TV. Please use the following chart to determine which
connection is best for you. Proceed to the appropriate page and connect your TV.
Components
Cables
Needed
Coaxial
G-LINK cable
Connection
Title
TV + VCR
Coaxial
TV Only
G-LINK cable
Coaxial
G-LINK cable
TV + VCR +
Satellite Receiver
Go to...
page 8
page 9
pages 10-11
Cables Needed to Connect Components to Your TV
The pictures below show the cables needed for the connections represented in this book.
Note: Please locale the G-LINK cable (provided) when you're gelling ready to set up your
TK. You need to connect Ibis cable lo your TV,,and lo your VCR and/or cable box in
order for all q/'lhe,/'eatures o/'lhe program guide lo work properly.
G-LINK cable
Coaxial cable
Chapter 1 7
C@nn ct @ns S tup
TV (backpanel)
G-LINK
CARLE/
VCR
\
VIDEO AUDIO IN FROM ANT
R L
R L
FromCable,
Cable Box,
or Antenna
Connection: TV + VCR
1°
2°
°
Connect your TV to your VCR
Connect a coaxial cable to the CABLE/ANTENNA jack on your TV and to the Output Jack on your
VCR (sometimes labeled OUT TO TV).
Connect cable or antenna to your VCR
Connect the coaxial cable from your cable outlet, cable box, or antenna to the Input Jack on your
VCR (sometimes labeled IN FROM ANTENNA or IN FROM ANT).
Connect the G-LINK cable to the TV
A. If you haven't already done so, remove the Demo Pin from the G-LINK jack.
B. Connect the G-LINK cable to the G-LINK jack on the TV. Next step, place the wands of the G-
LINK cable to work with your VCR (instructions are on p. 13).
Go to page 13
8 Chapter 1
C@nn ct @ns N tup
TV (back panel)
G-LINK
CABLE/
Cable
or Antenna
Connection: TV Only
1. Connect the TV to your cable or antenna
Connect the coaxial cable from your cable or antenna to the CABLE/ANTENNA jack on the back
of your TV.
Go to page 14
2. If you're connecting a cable box, connect the G-LINK cable
A. If you haven't already done so, remove the Demo Pin from the G-LINK jack.
B. Connect the G-LINK cable to the G-LINK jack on the TV. Next step, place the wands of the
G-LINK cable to the cable box (instructions are on p. 13).
Go to page 13
Chapter 1 9
C@nn_ct_@ns _ S_tup
SMELLITE RECEIVER FromCableorAntenna
VCR
OUT
09_
VIDEO R L
IN FROMANT
OUTTOTV
S-VIDEO
SATELLITE
IN
VIDEO AUDIO
0 °UTO
R L
0 'N9
R L
IN
OUTTO TV
CH3[i]
CH4U
Satellite
Signal
TV (backpanel)
G-LINK
ANTENNA
10 Chapter 1
C@nn ct @ns N tup
Connection: TV + VCR + Satellite Receiver
1. Connect coaxial cables to the Satellite Receiver
A. Connect the coaxial cable from your cable outlet, cable box, or antenna to the Input Jack
on your satellite receiver (sometimes labeled IN FROM ANT).
B. Connect the coaxial cable from your satellite dish antenna to the Input Jack on your
satellite receiver (sometimes labeled SATELLITE IN).
2. Connect the Satellite Receiver to the VCR and to the TV
.
A. Connect a coaxial cable to the Output Jack (sometimes labeled OUT TO TV) on the
satellite receiver and to the Input Jack on the VCR (sometimes labeled IN FROM ANT).
B. Connect a coaxial cable to the Output Jack on the VCR (sometimes labeled OUT TO TV)
and to the CABLE/ANTENNA jack on the TV.
Connect G-LINK cable
A. If you haven't done so, remove the Demo Pin from the G-LINK jack.
B. Connect the G-LINK cable to the G-LINK jack on the TV. Next step, place the wands of
the G-LINK cable to work with your VCR (instructions are on p. 13).
Go to page 13
Chapter 1 11
C@nn ct @ns S tup
The Front of Your TV
Front Panel
If you cannot locate your remote you can use the front panel of your TV to
operate many of the TV's features.
MENU Brings up the Main menu. When in the menu system, it selects
highlighted items. Also returns you to the previous menu. Press and hold MENU
for two seconds to access the GUIDE Plus+ system.
CH v Scans down through the current channel list. When you're using the TV's
menu system, it acts like the arrow down button on the remote control.
CH A Scans up through the channel list. When you're using the TV's menu
system, it acts like the arrow up button on the remote control.
¥OL- Decreases the volume. When you're using the TV's menu system, it acts
like the left arrow button on the remote control.
¥OL + Increases the volume. When you're using the TV's menu system, it acts
like the right arrow button on the remote control.
POWER Turns the TV on and off.
I VIDEO AUDIO I
Front Panel Jacks
You can access the component you connected by pressing the INPUT button on
your remote (FRNT appears on the screen).
VIDEO (in) Allows you to connect a component such as a VCR, camcorder or
Internet access device.
AUDIO (in) Receives audio signals from another component such as a VCR,
camcorder or Internet access device.
12 Chapter I
C@nn ct @ns N tup
Why You Should Connect This G-LINK Cable
The G-LINK cable enables the GUIDE Plus+ system (the on-screen interactive program guide) to
work with your VCR and/or cable box.
Cable Box- If your TV is connected to a cable box you must connect the G-LINK cable to
receive TV program listings for your area, and to tune directly to a channel when the program
guide is on your TV screen.
YCR - If your TV is connected to a VCR and you don't connect the G-LINK cable, one-touch
recording won't work. The other features of the guide will work properly.
le
G-LINK wands
How to Find the Remote Sensor
You have to place the G-LINK wands in front of the remote sensor on the VCR and/or cable box.
Some cable boxes and VCRs have the remote sensor labeled on the unit. If the remote sensor
isn't labeled on your VCR and/or cable box, you need to use the remote control that came with
the VCR and/or cable box to locate the sensor.
1. Turn off the VCR and/or cable box.
2.
.
Hold the remote control (not the one that came with your TV, but the one that came with
the cable box and/or VCR to which you're attaching the G-LINK cable) so that it is touching
the front of the component.
Slowly move the remote control across the front of the component (VCR or cable box) while
you press the power button on and off'. You must press and release the power button each
time you move the remote (holding down the button won't work).
.
When the component turns on, you've located the remote sensor.
r0
If you don't have both a
cable box and a VCR
connected to your TV,
just coil the cable of the
extra G-LINK wand with a
twist tie and leave it
behind the TV.
Placing the G-LINK Wands
Place the G-LINK wands in front of the remote sensor on your VCR and/or cable box
approximately one inch away from the remote sensor (see instructions below).
IV (back panel)
CABLE/
i_Connect to G-LINK jack _ ANTENNA
E on the back of the TV.
Chapter 1 13
C@nn_ct_@ns _ N_tup
Plug in the TV
Plug the end of the power cord into the wall outlet. Match the wide [)lade of the
plug with the wide slot in the outlet. Insert the plug completely into
the outlet.
Put Batteries in the Remote
1. Remove the battery compartment cover on the remote.
2. Insert new batteries. Match the polarities (+ and -) on the batteries with the
diagram on the remote.
3. Put the battery compartment cover back on the remote.
d2_
<_6C>
K27'
Use the arrow buttons and the OK
button to move through the menu
system.
How to Use the Remote Control to
Complete the Interactive Setup
The technical term is "Navigation" - how you move through the on-screen
menus. The theory is the same throughout the menu screens: highlight your
choice and select it.
To highlight a menu item, press the arrow buttons on the remote to highlight
one of the items listed on the screen. Use the up or down arrow button to move
up or down. Use the right or left arrow button to move right or left.
To select the item that you've highlighted, press OK.
Note: Highlighted means that the menu item stands out,/)om
other menu items on the list (appea_ darke< brighte< or a
d(/'/'erent color).
Turn on the TV
Press the POWER button on the remote control or the TV (the first screen of the
Interactive Setup appears). The menu screens "time out" after a period of time if
you don't make a selection. The tips in this section tell you how to access the
Setup menu screens manually.
14 Chapter 1
C@nn cti@ns N tup
Tip
To access the setup menus manually,
press MENU and choose Setup.
Complete the Interactive Setup
The menu system in your TV allows the TV's features to work properly. In this
book, we call it the "interactive setup" because the TV asks you questions, you
answer, and the TV makes the appropriate adjustments. The first time you turn
on your TV, the setup screens appear automatically.
Set the Menu Language
The first part of the ,52_TUPasks you to select your preferred language for the
menu system.
1. Highlight your preferred language for the menu system.
2. Press OK to select that language.
Complete Auto Channel Search
The next part of the 52_TUPasks you if you want the TV to search for all
channels viewable through your antenna or cable TV system. This is sometimes
called "auto programming."
1. Press OK to tell the TV to begin searching for channels. A progress report
appears on the screen.
2. When the screen on the TV tells you the search is complete, press OK (the
first GUIDE Plus+ system setup screen appears).
Note: I,/'you skip Auto Channel Search now, you can access it later
through the Channel menu, See Chapler 3,/br more delails,
Tip
If you move to a new zip or postal
code, or if any of your information
changes, you need to access the
setup screens from the TV's main
menu-- press MENU, choose GUIDE
Plus+ Menu, and choose GUIDE
Plus+ Setup.
The GUIDE Plus+ System Setup
The GUIDE Plus+ system is an on-screen interactive program guide that lists
what shows are on TV in your area. In order to receive program listings, you
need to complete the following steps.
The G-LINK cable must be connected to the back of your TV, and the wands
must be placed in front of the remote sensor on the cable box and/or VCR in
order for the GUIDE Plus+ system to work (go back to p. 13 for details).
1. You should see a screen displaying the features of the Guide Plus+ system.
Press OK to continue.
2. The next screen asks you to locate setup materials and hardware. Once you
have done this, press OK to continue.
Chapter 1 15
C@nn cti@ns S tup
Step 1: Identifying Your TV's Location
1. If your country is highlighted, press OK on the remote control.
If your country isn't highlighted, press the up or down arrow button on the
remote control to highlight your country and press OK.
2.
Use the number buttons on your remote to enter your zip code.
Press OK when you're finished.
Note: IJ'yourpostal code contains letters, press the up and down arrow
buttons on your remote to enter letters, andpress the right arrow button
to go to the next ,space. The left arrow button moves you to the left.
Step 2: Configuring for Cable
The next series of screens asks you about your cable setup. To supply your TV
with the correct TV program listings, the GUIDE Plus+ system needs to know if
your TV is connected to cable.
1. If your TV is connected to cable, highlight Yes and press OK.
If your TV isn't connected to cable, highlight No and press OK (STEP 3."
CbnJTguring for a VCR appears).
2.
If you have a cable box connected to this TV, highlight Yes and press OK on
your remote control.
Note: The next series of screens are very important because GUIDE Plus+
system must,find the correct cable box information in order for the
program schedule to be correct in your TV's program guide.
If you don't have a cable box connected to this TV, highlight No and
press OK (STEP 3: ConJTguring for a VCR appears).
rip
If you're not sure which channel is the
cable box's output channel, consult
the book that came with your cable
box or contact your cable company.
16 Chapter I
C@nn ¢ti@ns S tup
.
Highlight the channel to which you have to tune your TV in order to see
cable programming, and press OK (a screen appears reminding you to
connect your G-LINK cable to your TV and cable box).
Note: Channel 03 is lhe most common.
4. Highlight your brand of cable box, and press OK.
If your brand isn't listed, highlight Not Listed and press OK.
.
Make sure your cable box is on.
Tune the cable box to channel 02 (use the remote control that came with
your cable box, or press the channel buttons on the cable box).
Press OK (the GUIDE Plus+ system starts testing codes).
Important Note: When code lesting is in progress, don'l louch your TV,,
VCR, cable box or any (7/'the remote controls for lhese producls.
.
Look at your cable box. If it is still on and changed to channel 09, the test
was successful. Highlight Yes, and press OK (STEP 3: (2mJTguring for a VCR
appears).
If your cable box didn't change to channel 09 or turned itself oft', you have
two choices: No and Test this code again.
Test Ibis code again: If you think the TV, the cable box, or any of the
remote controls might have been touched or bumped during the test,
highlight Test this code again and press OK (the GUIDE Plus+ system runs
the same set of codes).
No: If you don't think the test was interrupted, highlight No and press OK
(GUIDE Plus+ system tests the next code).
Repeat the previous instructions until the TV finds the correct cable box
code. Follow the instructions on the screen.
Note: If the TV can 'lfind your cable box code, a troubleshooting
checklist appea_. CareJ'ully review each checklist and follow the
instr_tctions on lhe screen.
Chapter 1 17
C@nn cti@ns S tup
Step 3: Configuring for a VCR
1. If your TV is connected to a VCR, press OK.
If it is not, highlight No and press OK (a screen appears reminding you to
connect your G-LINK cable to your TV and VCR).
2.
Use the up and down arrow buttons to highlight the brand of your VCR that
is connected to the TV.
If your brand isn't listed, highlight Not Listed and press OK.
.
Tune your VCR to channel 02. Next, turn OFF your VCR. When you
complete these steps, press OK to begin testing.
Important Note: When code testing is in progres& don 7touch your TV,,
VCR, or any o/'the remote controls for these products.
.
Look at the front display of your VCR. If your VCR turned on automatically
and changed to channel 09, the test was successful. Highlight Yes and press
OK.
If your VCR didn't change to channel 09, you can either choose No or Test
this code again.
If you think your TV or remotes might have been touched during the test,
tune your VCR to channel 02, turn off"your VCR and highlight Test this
code again.
If you don't think the test was interrupted, highlight No. Tune your VCR to
channel 02 and turn off"your VCR. Press OK (the GUIDE Plus+ system starts
testing another set of codes.)
Keep following the previous instructions until the VCR finds the correct
code.
18 Chapter 1
Loading...