RCA DRC6331 - Portable DVD Player User Manual

C. Using the built-in battery

The unit has a built-in, non-replaceable, rechargeable battery. Charge the built-in battery before using it for the  rst time. The normal charging time should be completed within 4-5 hours. The charging light will go out when the built-in battery becomes fully charged.

To recharge the built-in battery

Turning on the unit

1. Slide the CHARGE / STANDBY / ON switch on the left side of the unit to the ON position.

2. The start-up picture will appear on the screen.

3. After use, slide the CHARGE / STANDBY / ON switch to the STANDBY (power o ) position.

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with a dry cloth.

7. Do not block the ventilation openings. Install in accordance with the manufacturer's instructions.

8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including ampli ers) that produce heat.

9. Do not defeat the safety purpose of the polarized or grounding - type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

10. Protect the po wer cord fro m being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

11. Only use attachments/accessories specified by the manufacturer.

12. Use only with a cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.

13. Unplug this apparatus during lightning storms or when unused for long periods of time.

1. LCD screen

2. AV IN / DVD switch

3. DC IN 9V / CAR PLUG -12V jack

4. VIDEO IN/OUT jack

5. AUDIO IN/OUT jack

6. CHARGE / STANDBY / ON switch

7. VOLUME control Adjusts the volume.

8. Headphone jack

Unit

Cautions:

• Use the provided 12V car power adapter only. Use with other car power adapters could damage the unit.

• The 12V car power adapter included with this unit is for its use only. Do not use it with other equipment.

• In the interest of tra c safety, do not operate this unit or view videos while driving a vehicle.

• Make sure the unit is securely fastened to prevent it from falling or  ying through the air in the event of an accident.

• When the inside of the cigarette lighter socket is dirty with ashes or dust, the plug section may become hot due to poor contact. Be sure to clean the cigarette lighter socket before use.

• After use, disconnect the 12V car power adapter from both the unit and cigarette lighter socket.

To CAR PLUG -12V Jack

Car power adapter

To cigarette lighter socket

B. Using the car power adapter

Warning:

Disconnect the car power adapter when not in use. Not for use in 24V vehicles.

14. Refer all servicing to quali ed service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

A. Using the AC power adapter

Cautions:

• The AC power adapter included with this unit is for its use only. Do not use it with other equipment.

• When the unit is not going to be used for long time, disconnect the AC power adapter from the AC power outlet.

• When the AC power adapter is plugged in, the apparatus is not completely disconnected from the main power supply, even when the power is turned o .

9. PLAY button Starts or resumes playback of a disc. STOP button Stops playing a disc.

PAUSE button

Pauses playback of a disc. Each time you press

the

PAUSE button the picture advances one frame. Press the PLAY button to resume playback.

PREV button

Press to go back to the previous chapters /

tracks.

NEXT button

Press to advance chapters / tracks.

Notes:

• When the built-in battery power is low, "Battery Low" will display on the screen and the unit will stop playing.

• Recharge the built-in battery when you are ready to use it again.

• While using the built-in battery, the environmental temperature should be 41°F (5°C) to 95°F (35°C).

• To get the longest service life of the built-in battery, charge at indoor-temperature.

• The built-in battery in this device may present a risk of fire or chemical burn if mistreated. Do not disassemble, heat above 212

F (100oC), or incinerate.

• The unit should not be exposed to excessive heat such as sunshine,  re or the like.

• When discarding the unit, environmental problems must be considered and local rules or laws governing the disposal of such products must be strictly followed.

Warnings:

• The built-in battery can only be recharged when the unit is in CHARGE mode while using the AC power adapter.

• The built-in battery cannot be recharged when the unit is in ON mode.

• Do NOT recharge the built-in battery in a vehicle using the car power adapter.

• Batteries should not be exposed to excessive heat such as sunshine,  re or the like.

The unit can playback

Region management information

Region Management Information: This unit is designed and manufactured to respond to the Region Management Information that is encoded on DVDs. If the region number printed on the DVD does not correspond to the region number of this unit, it cannot play that disc.

The region number of this unit is 1.

Notes on unauthorized discs

You may not be able to play some DVDs on this unit, particularly if they were purchased from outside your geographic area or made for business purposes.

DVDs [8cm/12cm disc]

Compatible

Audio CDs [8cm/12cm disc]

Disc function or operation that is not available

When the symbol appears on the screen, it indicates the function or operation attempted is not available at that time. This occurs because the DVD manufacturer determines the speci c functions of DVDs. Certain functions may not be available on some DVDs. Be sure to read the documentation provided with the DVD.

Icons used on DVDs

Sample lcons

Note:

When playing back a CD-G (Graphics) or CD EXTRA disc, the audio portion will be played, but the graphic images will not be shown.

Language selections for audio

Language selections for subtitles

Screen aspect ratio

Multiple camera angles

Region code indicator

Title, chapter and tracks

• DVDs are divided into “titles” and “chapters”. If the disc has more than one movie on it, each movie would be a separate “title”. “Chapters” are sections of titles.

• Audio CDs are divided into “tracks”. A “track” is usually one song on an Audio CD.

Note: Numbers identify each title, chapter, and track on a disc. Most discs have these numbers recorded on them, but some do not.

Please check and identify the supplied accessories.

Remote Control (with battery) ...............................................................................................................................................x 1

AC Power Adapter.......................................................................................................................................................................x 1

Car Power Adapter......................................................................................................................................................................x 1

Battery replacement

When the battery becomes weak, the operating distance of the remote control will be greatly reduced and you will need to replace the battery.

2. Insert one CR2025 (3V) size battery.

To change remote battery

1. Open the battery door.

Remove the

PLASTIC sheet

before USING the

Remote Control.

Note: If the remote control is not going to be used for a long time, remove the battery.

WARNING: Do not dispose of the battery in a  re or it may leak and/or explode.

WARNING: Batteries should not be exposed to excessive heat such as sunshine,  re or the like.

CAUTION: Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type.

To AC po wer outlet

To DC IN 9V jack

Slide the switch to CHARGE

Charging light ON

Recharging is completed when charging light goes out

AC power adapter

Disc formats

user manual

Read these instructions before using your new product for the  rst time.

DRC6331

Important safety instructions

Safety precautions

* SEE BOTTOM OF UNIT FOR GRAPHIC SYMBOLS *

WARNING:

Should any trouble occur, disconnect the AC power adapter and refer servicing to a quali ed technician.

The lightning flash with an arrowhead symbol, within the equilateral triangle, is intended to alert the user to the

presence of uninsulated "dangerous voltage" within the product's enclosure that may be of su cient magnitude to cause an electric shock.

The exclamation point within the

equilateral triangle is intended to alert

the user to the presence of important

operating and maintenance (servicing) instructions in this owner’s manual.

Accessories

Using the remote control

• Point the remote control at the REMOTE SENSOR located on the unit.

• When using this unit in very bright light, the infrared REMOTE SENSOR may not work properly.

• The recommended e ective distance for remote operation is about 16 feet (5 meters).

Remote control

Control reference guide

SEARCH button Press to perform fast reverse playback.

SEARCH button

Press to perform fast forward playback.

10. PUSH OPEN fovea Open and close the disc door.

11. Remote sensor Receive the remote control unit signals.

12.

(CHARGING) indicator

Charge the rechargeable battery before using

it for the first time. The normal charging time should be completed in approximately 4-5 hours. The charging light will go out when the battery becomes fully charged.

13. ON indicator

Power supply

AC power adapter

To DC IN 9V Jack

To AC power outlet

Warning:

The AC/DC adapter is used as a disconnect device and it should remain readily operable during intended use. In order to disconnect the apparatus from the mains completely, the AC/DC adapter should be disconnected from the outlet completely.

The 12V car power adapter allows the unit to be used with vehicles that have a 12V, negative ground electrical system.

The supplied AC power adapter operates on AC 120V.

AVC Multimedia, Markham, Ontario, L3R 1E3

http: //www.1800customersupport.com/RCA

This product contains a low power laser device.

THIS CLASS B DIGITAL APPARATUS COMPLIES WITH CANADIAN ICES-003.

WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-

SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. DO NOT PLACE OBJECTS FILLED WITH LIQUIDS ON OR NEAR THIS UNIT. CAUTION: USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED MAY RESULT IN HAZARDOUS RADIATION EXPOSURE. CAUTION: DANGER OF EXPLOSION IF BATTERY IS INCORRECTLY REPLACED. REPLACE ONLY WITH THE SAME OR EQUIVALENT TYPE.

Remote control

1. VIDEO MODE button Adjusts Brightness,

Panel Display and Contrast of the LCD screen.

PREV button

Move back through

titles, chapters or tracks on a disc.

/ SEARCH

buttons

SEARCH: Fast

reverse playback.

SEARCH: Fast

forward playback.

4. GOTO button Skip directly to a location on a DVD.

5. Cursor ( ,

, , ) buttons

Move between selections on a menu screen and adjust

certain settings. ENTER button Con rm selections on a menu screen.

6. MEMORY button Set titles/chapters/tracks in a favorite order.

7. Number (0 - 9) buttons Use when creating programs or locating a title/chapter/

track or speci c time.

8. REPEAT A-B button Perform point-to-point repeat playback on a DVD or CD. REPEAT DISC button Repeat a DVD chapter or title. Repeat a CD track or the whole disc.

SETUP button In DVD Stop Mode, press to display the

unit’s SETUP menu.

9. MENU button Enter and exit the main DVD menu.

10.

NEXT button

Move forward through titles, chapters or

tracks on a disc.

11.

STOP button Stop playing a disc. PLAY button Start or resume playback of a disc.

PAUSE button Press once to pause playback. Press

subsequently to advance frame by frame on a DVD.

12. DISPLAY button Show status information on the screen.

13. ANGLE button Switches between multiple camera angles

if applicable to the DVD.

14. AUDIO button Select one of the audio sound tracks on

a DVD (if more than one is available) or select the audio output mode on a CD.

15. SUBTITLE button Selec t one of the subtitle languages

programmed on a DVD (if available). RETURN button Return to normal operation after using the

SETUP menu of a DVD.

SUBTITLE/ RETURN

98 07

ENTER

MEMORY

DISPLAY

AUDIO

GOTO

VIDEO MODE

STOP

PAUSE

PLAY

ANGLE

SETUP

A-B DISC

REPEAT

1 2

3 4

12 13 14 15

Watching a DVD on your TV

1. Turn on the unit and slide the AV IN / DVD switch to the DVD position.

2. Turn on the TV and follow the instructions included with it to play the DVD.

A. Connecting a TV

If your TV has Audio/Video inputs, you can connect the unit to your TV using the Audio/Video cable.

C. Using headphones/earphones

• Turn down the volume before connecting, and then adjust the level.

• When headphones/earphones are connected, no sound will be emitted from the unit's speaker.

Headphones/

Earphones

(3.5mm diameter

plug)

Caution:

Avoid listening to sound at levels which may be harmful to your ears.

To AUDIO / VIDEO IN / OUT cacks

Audio / Video cable

(not included)

White Red Yellow

Audio / Video cable

(not included)

Watching video equipment

1. Turn on the unit and slide the AV IN / DVD switch to the AV IN position.

2. Turn on the video equipment and follow the instructions provided with it to playback.

B. Connecting to a video equipment

You can connect other video equipment for playback through the unit.

Connections

Video

equipment

To AUDIO / VIDEO IN / OUT cacks

Audio / Video cable

(not included)

White Red Yellow

Audio / Video cable

(not included)

On placement

• Do not use the unit in places that are extremely hot, cold, dusty, or humid.

• Place the unit on a  at and even surface.

• Do not restrict the air  ow of the unit by placing it in a place with poor air  ow, by covering it with a cloth, or by placing it on carpeting.

• To avoid magnetizing, do not place the unit near speakers or magnets.

• Do not use this unit in direct sunlight or leave the unit in a closed automobile (or yacht, etc) where it would be exposed to high temperatures above 104°F (40°C).

• No naked  ame sources such as lighted candles should be placed on the AC power adapter or the main unit.

• The apparatus should not be exposed to splashing or dripping liquids, and no objects  lled with liquids, such as vases, should be placed on apparatus.

On safety

• When connecting or disconnecting the AC power adapter, grip the plug and not the cord itself. Pulling the cord may damage it and create a hazard.

• When you are not going to use the unit for a long period of time, disconnect the AC power adapter.

On condensation

• When left in a heated room where it is warm and damp, water droplets or condensation may form inside the unit. When there is condensation inside the unit, the unit may not function normally. Let the unit stand for 1 to 2 hours before turning the power on, or gradually heat the room and allow the unit to dry before use.

Ventilation warning

• Do not block the ventilation openings or holes. If the ventilation openings or holes are blocked by a newspaper or cloth, etc., the heat may not be able to get out.

• Do not operate the unit in a con ned space, such as a bookcase or built-in cabinet. Allow about 4 inches (10cm) of free space all around the unit for adequate ventilation.

Rating plate location

• The rating plate is located on the bottom of unit.

FCC statements

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one or more of the following measures: – Reorient or relocate the receiving antenna. – Increase the separation between the equipment and receiver. – Connect the equipment into an outlet on a circuit di erent from that to which the receiver is connected. – Consult the dealer or an experienced radio/TV technician for help. Warning: Changes or modi cations to this unit not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

Notes on copyright

It is forbidden by law to copy, broadcast, show, broadcast on cable, play in public, or rent copyrighted material without permission. Apparatus Claims of U.S. Patent Nos. 6,836,549; 6,381,747; 7,050,698; 6,516,132 and 5,583,936 licensed for limited viewing uses only. This product incorporates copyright protection technology that is protected by U.S. patents and other intellectual property rights. Use of this copyright protection technology must be authorized by Macrovision, and is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision. Reverse engineering or disassembly is prohibited.

Chapter1

Title1 Title2

Chapter2 Chapter3 Chapter1 Chapter2

Track1 Track2 Track3 Track4 Track5

Locating a speci c chapter / title

If you know the chapter/title number for the chapter that you want to play, you can locate it by directly selecting that number.

1. Press the GOTO button.

2. Press the

/ button to highlight chapter/title number, press the corresponding number buttons (2 digits) for the chapter/title you want (For example: 02, 08, 10 or 15). If you press only 1 numeric button, press the ENTER button to con rm.

3. Playback starts from the selected chapter/title.

Notes:

• If the chapter/title number entered is not permitted by the DVD, "

Input invalidInput invalid

" will display. Repeat steps

1 and 2 to re-enter the correct number.

• Some discs may not respond to this process.

• This method of locating a chapter/title is available only on a DVD that contains chapter/title numbers.

Locating a speci c time

You can move to a speci c location by entering its corresponding time (hours, minutes, seconds).

1. Press the GOTO button two times.

2. Press the corresponding number buttons (5 digits: X:XX:XX, for example: 0 30 05, 1 08 23, 1 22 56) for the setting point you want.

3. Playback starts from the selected section.

Notes:

• If the time entered is not permitted by the DVD, "

Input invalidInput invalid

" will display. You should re-enter the correct

time.

• Some discs may not respond to this process.

• Some scenes may not be located as precisely as you speci ed.

• This method for accessing speci c locations is available only within the current title of the DVD.

Locating a speci c disc / track time

You can move to a speci c location by entering disc/track time (minutes, seconds).

1. Press the GOTO button until the below bar appears.

2. Press the corresponding number buttons (4 digits: XX:XX, for example: 30 05, 02 23) for the setting point you want.

3. Playback starts from the selected section.

Notes:

• If the time entered is not permitted by the CD, "

Input invalidInput invalid

" will display. You should re-enter the correct

time.

• Some scenes may not be located as precisely as you speci ed.

Selecting a speci c track

1. Press the GOTO button 3 times.

2. Press the corresponding number buttons (2 digits) for the track you want (For example: 02, 08, 10 or 15). If you press only 1 numeric button, press the ENTER button to con rm.

3. Playback starts from the selected track.

Notes:

• If the track number entered is not permitted by the CD, "

Input invalidInput invalid

" will display. Repeat steps 1 and 2

to re-enter the correct number.

• You can also directly press the number buttons to select a track.

Subtitle selection

1. While a DVD is playing, press the SUBTITLE button to display the current language setting, as shown in the example.

2. Press the SUBTITLE button repeatedly to select the desired subtitle language. You can turn subtitles off by pressing the SUBTITLE button repeatedly until the “

Subtitle OffSubtitle Off

” is displayed.

Notes:

• Some DVDs are set to display subtitles automatically, and you cannot turn them off even if you set the subtitle function to o .

• During some scenes, the subtitles may not appear immediately after you select your desired scene.

• The number of subtitle languages recorded differs depending on the disc. If only one language is recorded, the language does not change.

• This function can only be used for discs on which subtitles have been recorded in multiple languages.

• Some DVDs allow you to change subtitles using the disc menu only. If this is the case, press the MENU button and choose the appropriate subtitle on the disc menu.

Skip forward / reverse

• Press the NEXT button to advance chapters/ tracks.

• Press the

PREV button to go back to current

or previous chapters/tracks.

• For an Audio CD, use the number buttons on the remote control to jump directly to the desired track number.

Audio selection

On some DVDs, the sound is recorded in two or more formats. Follow the directions below to select the preferred language and sound system.

1. While a disc is playing, press the AUDIO button to show the current audio format number.

2. Press the AU DIO button repeatedly to select the desired audio format.

Notes:

• If only one audio format is recorded on the DVD, the number does not change.

• Some DVDs allow you to change audio selections using the disc menu only. If this is the case, press the MENU button and choose the appropriate language on the disc menu.

• You can select different audio channels (Stereo, Mono Left, Mono Right or Mix-Mono) on an Audio CD by pressing the AUDIO button repeatedly.

Stopping playback

Press the STOP button at the location where you want to interrupt playback. To resume playback at the position where the disc was stopped, press the

PLAY button. If you press the STOP button twice, the unit’s memory will be cleared and pressing the PLAY button will reset the DVD to the beginning.

Fast forward / Fast reverse

1. Press the SEARCH or SEARCH button

when a disc is playing. Each time you press the SEARCH

or SEARCH button, the playback

speed changes in the following sequence:

2. Press the PLAY button when you reach the

desired point to resume normal playback.

Notes:

• The DVD player mutes sound and subtitles

during reverse and forward scan of DVDs.

• The fast playback speed may differ depending

on the disc.

Printed in China 811-633191W021

Symptom Cause (and remedy)

• Ensure the AC power adapter is connected.

• The unit is not turned on.

• Make sure the infrared remote sensor is not blocked.

• Make sure the plastic sheet has been removed from the remote control.

• Point the remote directly at the infrared remote sensor on the unit.

• Replace the battery in the remote control with a new one.

• Make sure DVD mode is selected.

• The system is in pause mode. Press the

PLAY button to return to normal play mode.

• The unit is in fast-forward or fast-reverse mode. Press the PLAY button to return to normal play mode.

• Make sure the AUDIO/VIDEO output connections are correct.

• The DTS DVD cannot be decoded to have speaker output.

• The unit is too hot; shut o the unit for 30 minutes to cool it down.

• The region number of the disc doesn't match the region number of this unit.

• Clean the disc.

• The disc is scratched.

• Adjust the LCD's brightness and contrast using the VIDEO MODE button on the remote control.

• The plugs and jacks are dirty. Wipe them with a cloth slightly moistened with alcohol.

• Clean the disc.

• There is no disc inside (“No Disc” appears on the screen).

• Insert the disc correctly with the playback side facing down.

• Clean the disc.

• A non-NTSC disc has been inserted. The unit and disc region number are incompatible.

• Condensation may have formed inside the unit due to a sudden change in temperature. Wait about an hour for it to clear and try again.

No power.

The remote control does not function.

No sound or only a very low-level sound is heard.

No picture.

The picture is not clear.

Severe hum or noise is heard.

The disc does not play.

System setup

1. Press the SETUP button in stop mode.

2. Press the

/ button to select System Page.

3. Press t he

/ button to select the option (TV Display or

Default), then press the

button.

4. Press the

/ button to adjust the settings, then press the

ENTER button to con rm.

5. Repeat steps 3 and 4 to adjust other options. Press the button to return to the previous menu.

6. Press the SETUP or RETURN button to exit the menu.

Default

It takes 3-5 seconds to reset the DVD settings to the factory default.

TV Display

Pan Scan

• When wide-screen video is played, this mode clips the right and left sides of the image so that it can be viewed on a conventional screen.

• Some wide-screen DVDs that do not permit Pan Scan mode playback are automatically played in letterbox mode (black bands that appear at the top and bottom of the screen).

Letter Box

• When wide-screen video is played in this mode on a conventional screen, black bands appear at the top and bottom of the screen.

Wide Screen

• This is the correct mode for playing wide-screen videos on the unit screen or other external wide-screens.

Notes:

• The displayable picture size is preset on the DVD. Therefore the playback picture of some DVDs may not conform to the picture size selected.

• When you play DVDs recorded in the 4:3 aspect ratio, the playback picture will always appear in the 4:3 aspect ratio regardless of the TV display setting.

• Select Wide Screen to conform the LCD screen on the unit. Always be sure that your TV display conforms to the actual TV in use if you connect the unit to a TV.

Wide Screen

Letter Box

Cut off when a wide-screen video image is played.

Pan Scan

Tv Display Default

Wide No

Go To System Page

- - System Page - -

System

Language

Video

You can play a specific title or chapter repeatedly. (Title repeat, chapter repeat, A-B repeat)

Repeating a chapter

1. While the DVD is playing, press the REPEAT DISC button until the “

ChapterChapter

” indicator displays on the screen. The current chapter is played repeatedly.

Repeating a title

2. While the DVD is playing, press the REPEAT DISC button until the “

TitleTitle

” indicator displays on

the screen. The current title is played repeatedly.

To resume normal playback

3. While the DVD is playing, press the REPEAT DISC button until the “

Repeat OffRepeat Off

” indicator displays

on the screen.

You can play a single track or the whole disc repeatedly.

Repeating a single track

1. While the CD is playing, press the REPEAT DISC button until the “ ” indicator displays on the screen. The current track is played repeatedly.

Repeating the whole disc

2. While the CD is playing, press the REPEAT DISC button until the “ ” indicator displays on the screen. The whole disc is played repeatedly.

To resume normal playback

3. While the CD is playing, press the REPEAT DISC button until the repeat indicator disappears from the screen.

Title 01/03 Chapter 03/12Title 01/03 Chapter 03/12

Title 01/03 Chapter 00/00Title 01/03 Chapter 00/00

Title 01/03 TimeTitle 01/03 Time ::

3. Press the PLAY button to start memory playback (“

ProgramProgram

” appears on the screen).

4. To resume normal playback from memory playback

1). Pres s the MEMORY button to display the

memory menu.

2). Use the Cursor buttons (

, , , ) to move the highlighted bar to “Stop”. Press the ENTER button to con rm “Stop”.

3). Press the ENTER button to confirm “Exit”. It will return to normal playback (“

ProgramProgram

”

disappear from the screen).

Notes:

• For a CD, you can only arrange order for tracks. The display will be a little di erent.

• If the title or chapter number entered is not permitted by the DVD, it will disappear. You should re-enter correct number.

• You should input items one by one following the 1, 2, 3 ... sequence.

• If the DVD contains only one title, you can only arrange order for chapters.

• Some discs may not permit memory playback operation.

• If you select repeat during memory playback, the DVD player repeats the current memory playback.

• If you press the MEMORY button while the display appears on the TV screen, the display disappears.

• The programmed selections will be cleared when you press th e STOP button two times, open the disc tray or turn o the DVD player.

Language setup

1. Press the SETUP button in stop mode.

2. Press the

button to select Language Setup Page.

3. Press the / button to select the option (OSD Language, Audio, Subtitle or Disc Menu), then press the button.

4. Press the

/ button to select your preferred language,

then press the ENTER button to con rm.

5. Repeat steps 3 and 4 to adjust other options. Press the button to return to the previous menu.

6. Press the SETUP or RETURN button to exit the menu.

Notes:

• Some DVDs may not play in the audio language you selected. A prior language may be programmed on the disc.

• Some DVDs may be set to display subtitles in a language other than the one you selected. A prior subtitle language may be programmed on the disc.

• Some DVDs allow you to change subtitle selections using the disc menu only. If this is the case, press the MENU button and choose the appropriate subtitle language from the selection on the disc menu.

• Some DVDs may not include your pre-selected language. In this case, the DVD player automatically displays disc menus consistent with the disc's initial language setting.

Video setup

1. Press the SETUP button in stop mode.

2. Press the

/ button to select Video Setup Page.

3. Press the /

button to select the option (Brightness or

Contrast), then press the

button.

4. Press the / button to adjust the setting, then press the ENTER button to con rm.

5. Repeat steps 3 and 4 to adjust other options. Press the button to return to the previous menu.

6. Press the SETUP or RETURN button to exit the menu.

You can combine your favorite titles/chapters/tracks and play them in the order you determine.

1. Press the MEMORY button while a disc is playing. The following display appears.

2. Input the title (2 digits) and chapter (2 digits) by pressing the number buttons (For example: 01 02, 02 05, 02 11). It will move to the next item automatically.

• You can use the Cursor buttons ( , , , ) to move the highlighted bar to any item, and reenter the title and chapter. Press the NEXT / PREV to move to the the next / previous setup page.

• You can use the Cursor buttons ( , , , ) to move the highlighted bar to “Clear”, “Exit”, “Star t” or “Next / Prev”, and press the ENTER button to con rm.

Clear: Delete all input programs. Exit: Exit memory menu and return to normal

playback.

Start: Start memory playback. Next / Prev: Move to the the next / previous setup

page.

Go To Language Setup Page

- - Language Setup Page - -

System

Language

Video

OSD Language Audio Subtitle Disc Menu

Eng Eng Off Eng

Brightness Contrast

Go To Video Setup Page

- - Video Setup Page - -

Language

00 00

System

Video

Adjust the LCD screen

You can adjust Brightness, Panel Display and Contrast of the LCD screen.

1. Press the VIDEO MODE button.

2. Press the / button to select Brightness, Panel Display or Contrast.

3. Press the / button to change the setting.

4. Press the VIDEO MODE button to exit the menu.

This owner’s manual explains the basic instructions for operating this unit. Some DVDs are produced in a manner that allows speci c or limited operation during playback. Therefore, this unit may not respond to all operating commands. THIS IS NOT A DEFECT. Please refer to the instructions accompanying the speci c DVD in question for more information about the options available on that DVD. “

” may appear on the screen during operation. A “ ” means the desired operation is not permitted

by the unit or disc.

Playing a disc

1. Slide the CHARGE / STANDBY / ON switch on the left side of the unit to the ON position.

See Customizing the function settings before

proceeding to step 2.

2. Press the PUSH OPEN fovea on the disc door to open the disc door.

3. Hold the disc by its sides and carefully place it onto the spindle with the label side facing up, pushing gently until you hear a “click”.

4. Pr ess the PUSH OPEN fovea to close the disc door. It takes a short while for your unit to load the disc. After loading, the unit will automatically bring you to the main menu of the DVD or start playing the DVD.

5. If the unit does not automatically start playing the DVD, press the PLAY button.

Pausing playback (still mode)

Press the PAUSE button. To resume normal playback, press the PLAY button. For a DVD, each time you press the

PAUSE button,

the picture advances one frame.

1. While you are playing a DVD with di erent angles recorded, press the ANGLE button to view the number of current angles available.

2. Press the ANGLE button repeatedly to change the scene to the next recorded angle.

• After approx. two seconds, playback will continue from

the new angle selected.

• If no button is pressed within 10 seconds, playback

continues without changing the current angle.

Sequence of angle shots (Example)

Audio 1/3:Dolby D 2ch EnglishAudio 1/3:Dolby D 2ch English

Subtitle 02/03:SpanishSubtitle 02/03:Spanish

2x 4x 8x

16x

2x 4x 8x

16x

2x 4x 8x

16x

2x 4x 8x

16x

1/31/311

/31 /32 /33

Display function

While the disc is playing, press the DISPLAY button repeatedly to display information on operation status.

Playing a disc (basic playback)

Dolby Digital

Dolby Digital is a technology developed by Dolby Laboratories. Soundtracks encoded in Dolby Digital can reproduce from one to 5.1 discrete channels of excellent quality audio. The unit automatically recognizes the Dolby Digital bitstream and provides a downmix suitable for twochannel listening. An additional Dolby Digital decoder is required for reproduction of the discrete multi-channel soundtracks available on many DVDs.

Manufactured under license from Dolby Laboratories. Dolby and the double-D symbol are trademarks of Dolby Laboratories.

Sound system Troubleshooting guide

Maintenance

Repeat playback

Repeating a speci c section

You can play a speci c section repeatedly.

1. While the disc is playing, press the REPEAT A-B button at the beginning of the section (“

”

is displayed) you want to play repeatedly.

2. Press the REPEAT A-B button again at the end of the section (“

ABAB

” is displayed).

3. The unit will immediately begin replaying your selection.

To resume normal playback

4. While the disc is playing, press the REPEAT A-B button until the “

AB OFFABOFF

” indicator displays on the screen (the repeat indicator disappears from the screen for a CD).

Notes:

• Some discs may not permit A-B repeat operation.

• You cannot set the A-B repeat function for a segment that includes multiple camera angles.

• You can specify a segment only within the current title or track.

• There may be a slight difference between point A and the location where playback actually resumes depending on the disc.

Angle selection

Some DVDs contain scenes that have been shot from a number of di erent angles. For these discs, the same scene can be viewed from each of these di erent angles.

Note: This function can only be used for discs on which scenes shot from multiple angles have been recorded.

Locating a desired section

Customizing the function settings

Programmable memory Viewing JPEG  les

This unit can play JPEG  les recorded on a CD-R or CD-ROM disc (CD-RW is not recommended).

Viewing JPEG  les

1. Press the PUSH OPEN fovea on the disc door to open the disc door.

2. Hold a JPEG  le disc by its edges and gently push it onto the spindle with the label side facing up until you hear a “click”.

3. Press the PUSH OPEN fovea to close the disc door. The JPEG  les on the disc will be displayed one by one automatically.

4. Press the MENU or

STOP button to display a folder list.

Press the /

button to highlight a JPEG  le to play. Press

the PLAY button to start playback.

Notes:

• You can press the

PAUSE button to freeze the picture. Press the PLAY button to resume picture slide show.

• You can press the STOP button to quit playback.

• You can press the

PREV or NEXT button to change the picture.

• You can press the ANGLE button to rotate direction of the picture by 90°.

• Some discs may not permit this operation.

Cleaning the disc

A defective or soiled disc inserted into the unit can cause sound to drop out during playback. Handle the disc by holding its inner and outer edges.

• Do NOT touch the surface of the unlabeled side of the disc.

• Do NOT stick paper or tape on the surface.

• Do NOT expose the disc to direct sunlight or excessive heat.

• Clean the disc before playback. Wipe the disc from the center outward with a cleaning cloth.

• NEVER use solvents such as benzine or alcohol to clean the disc.

• Do NOT use irregular shaped discs (example: heart shaped, octagonal, etc.). They may cause malfunctions.

Cleaning the unit

• Be sure to turn the unit o and disconnect the AC power adapter before cleaning the unit.

• Wipe the unit with a dry soft cloth. If the surfaces are extremely dirty, wipe clean with a cloth that has been dipped in a weak soap-and-water solution and wrung out thoroughly, then wipe with a dry cloth.

• Never use alcohol, benzine, thinner, cleaning fluid or other chemicals. Do NOT use compressed air to remove dust.

Important note

• Before transporting the unit, remove the disc from the disc compartment.

RCA DRC6331 - Portable DVD Player User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual