RCA CRCR351 User Manual

CRCR351
Universal Remote Control Owner’s Manual
SAVE THIS MANUAL AND THE CODE LISTS!
Remote controls can sometimes lose their programming when you change the batteries. Make sure you keep the manual and code lists in a safe place so that you can reprogram the remote if you need to.
Tip: This remote is already programmed to operate most RCA-branded TVs, VCRs, and satellite receivers. Just press the corresponding key—TV for a television, SAT•CBL•DTC for a satellite receiver, VCR•DVD for a VCR.
Step 1: Install your batteries
Step 2: Program your remote
To use this universal remote with your home entertainment system, first you need to program it to control your devices. There are four ways you can program the universal remote to operate your devices:
• The Auto Code Search goes automatically through all the codes for the device you’re trying to control. It’s the easiest method, but it can sometimes take longer than some of the other programming methods.
• The Brand Code Search searches through the codes for select brands of devices. It’s not as easy as the auto code search, but it can be faster.
• The Direct Code Entry lets you enter a code from the accompanying code list for your brand of device. It’s not as easy as the other methods, but it’s potentially the fastest method.
• The Manual Code Search lets you manually go through all the codes for the device you’re trying to control.
Auto Code Search
The Auto Code Search goes automatically through all the codes for the device you’re trying to control. When you find the one that operates your device, you can stop the search and store that code.
TIP: To exit without saving a new code at any point in the Auto Code Search, press the GO BACK key.
1. Manually turn on the device you
want to control.
Your universal remote requires two AAA alkaline batteries (not included).
To install the batteries:
1. Remove the battery
compartment cover.
2. Insert the batteries, matching
the batteries to the (+) and (–) marks inside the battery compartment.
3. Push the battery cover back into
place.
Battery Precautions:
• Do not mix old and new batteries.
• Do not mix alkaline, standard (carbon-zinc) or rechargeable (nickel-cadmium) batteries.
• Always remove old, weak or worn-out batteries promptly and recycle or dispose of them in accordance with Local and National Regulations.
Battery Saver
Your universal remote control saves battery power by automatically turning off if any key is pressed for more than 60 seconds. This saves your battery life should your remote get stuck in a place where the keys remain depressed, such as between sofa cushions.
2. If you’re programming the TV or SAT•CBL•DTC key, go
to step 3.
If you’re programming the VCR•DVD key, you need to
tell the remote which kind of device you want this key to control, VCR or DVD.
Press and hold the VCR•DVD key. While you’re holding
down the VCR•DVD key, use your other hand to press the number key for the type of device you want to control with this key: 2 for VCR, 3 for DVD. Then release both keys.
TV
TV
SAT•CBL•DTCVCR•DVD
SAT•CBL•DTCVCR•DVD
3. Press and hold the device key you want to program. While
you’re holding down the device key, use your other hand to press and hold the remote’s ON•OFF key at the same time.
TV
SAT•CBL•DTCVCR•DVD
TV
SAT•CBL•DTCVCRDVD
4. Wait until the remote’s indicator
comes on and stays on. Then release both keys.
DTC is a Digital TV Converter Box
5. Point the remote directly at the
Code Lists
Brand Codes are used for programming using the Brand Code Search
and Entry method outlined in the User’s Guide.
Lista de Códigos
Los códigos de las marcas son utilizados para programar utilizando los métodos de búsqueda y entrada de códigos de marcas, resaltado
en la guía del usuario.
0
1
2 3
4
5 6
7
8
9
RCA GE PROSCAN
Insignia
JVC
Magnavox Philips
PanasonicSamsung Sharp Sony Toshiba Vizio
TV
VCR
0
1
2 3
4
5 6
7
8
9
RCA GE PROSCAN
Apex JVC
Magnavox Philips
PanasonicPioneer Samsung Sharp Sony Toshiba
DVD
SAT/CABLE
0
1
2 3
4
5 6
7
8
9
RCA GE PROSCAN
Motorola DirecTV
Dish Network
Systems/ Echostar
General Instruments
Hughes Network Systems
Scientific Atlanta
Magnavox Philips
AMNIO ADB
Panasonic
Brand Code List/Lista de Códigos de Marcas
0
1
2 3
4
5 6
7
8
9
Samsung
Magnavox Philips
MitsubishiPanasonic Sharp Sony Toshiba
RCA GE PROSCAN
JVC
Symphonic
front panel of the device you want to control. Press PLAY on the remote and wait 5 seconds. The remote is testing a batch of 10 codes on your device.
Did your device turn off?
YES: Go to step 6.
NO: Press PLAY again. The remote tests the next batch of
10 codes.
Keep pressing PLAY every 5 seconds until your device turns
off.
6. When your device turns off, press
the REVERSE key on the remote and wait at least 2 seconds. The remote tries the last of the previous ten codes.
Did your device turn on?
YES: Press the STOP key. You’re
done! You’ve programmed this device key.
NO: Press REVERSE again. The remote tests the next code
in the batch.
Keep pressing REVERSE every 2 seconds until your device
turns back on. When it does, press STOP.
Note: If you accidentally press the REVERSE key after your device turns on, press the FORWARD key. Then, wait two seconds to see if your device turns off again.
NOTES
Throughout the programming of each key, be sure to keep the remote pointed at the IR sensor of the device you are currently programming the remote to control.
Test the remote with the device to make sure the device key is programmed with the correct code for maximum functionality. If some features don’t work, try a different code. See the “Testing the Code for Maximum Functionality” section below for more information.
During the Auto Code Search, the remote ignores keypresses that aren’t part of the search.
The search times out after two minutes (the indicator light blinks four times and turns off, and the last programmed code under that device key is retained).
The indicator light blinks four times and turns off when the remote has gone through all the codes. The remote exits the Auto Code Search. If your device hasn’t turned off yet, try a different search method.
Brand Code Search
The Brand Code Search goes through only the codes for one of the select brands listed in the accompanying code list. If your brand of device is listed, this search can be very quick and easy.
TIP: To exit without saving a new code at any point in the Brand Code Search, press the GO BACK key.
1. Manually turn on the device you
want to control.
2. If you’re programming the TV or SAT•CBL•DTC key, go
to step 3.
If you’re programming the VCR•DVD key, you need to
tell the remote which kind of device you want this key to control, VCR or DVD.
Press and hold the VCR•DVD key. While you’re holding
down the VCR•DVD key, use your other hand to press the number key for the type of device you want to control with this key: 2 for VCR, 3 for DVD. Then release both keys.
TV
TV
SAT•CBL•DTCVCR•DVD
SAT•CBL•DTCVCR•DVD
3. Find your device’s brand in the Brand
Code list section of the accompanying code list. Circle the number for your brand and keep the list handy.
4. Press and hold the device key you want to program. While
you’re holding down the device key, use your other hand to press and hold the remote’s ON•OFF key at the same time.
TV
SAT•CBL•DTCVCR•DVD
TV
SAT•CBL•DTCVCRDVD
5. Wait until the remote’s indicator
comes on and stays on. Then release
Testing the Code for Maximum Functionality
1. Try a variety of the device’s functions with the remote. If
some device features don’t work, go to the next step to try a different code.
2. Repeat the Auto Code Search Method from the beginning. When your device turns off, do not stop searching. Instead, with the unit now off, continue to press the PLAY key every 5 seconds until the unit turns back on.
3. Once the unit turns back on, press the REVERSE key on the remote every 2 seconds until your device turns off again. When your device turns off again, press the STOP key.
4. Test the key’s functionality again by attempting to control a variety of the device’s functions. If the code that has been stored controls the majority of the device’s functions, programming is complete. If the code stored does not give maximum functionality, try another code.
both keys.
6. Look at the number you circled for
your device’s brand code number. Press that number on the remote keypad.
TV
SAT•CBL•DTCVCR•DVD
Loading...
+ 4 hidden pages