RP5030
RP5035
It is important to read this instruction book prior to using your new product for the first time.
Nous vous recommandons de lire ce manuel d’instructions avant d’utiliser votre nouveau produit pour la première fois.
Es importante leer este manual antes de usar por vez primera su euipo.
User manual
Guide de l’utilisateur
Manual de usuario
RP5030 EN (B ver) 15/11/06 10:28 AM Page 2
64M
DIGITAL VOICE RECORDER
ERASE MENU
FCC Information
This device complies with Part 15 of the FCC
Rules. Operation is subject to the following
two conditions: (1) This device may not cause
harmful interference, and (2) this device
must accept any interference received,
including interference that may cause
undesired operation.
In accordance with FCC requirements,
changes or modifications not expressly
approved by Thomson Inc. could void the
user’s authority to operate this product.
This device generates and uses radio
frequency (RF) energy, and if not installed
and used properly, this equipment may
cause interference to radio and television
reception.
If this equipment does cause interference to
radio or television reception (which you can
determine by unplugging the unit), try to
correct the interference by one or more of
the following measures:
• Re-orient the receiving antenna (that is,
the antenna for the radio or television
that is "receivinag" the interference).
• Move the unit away from the equipment
that is receiving interference.
• Plug the unit into a different wall outlet
so that the unit and the equipment
receiving interference are on different
branch circuits.
If these measures do not eliminate the
interference, please consult your dealer or
an experienced radio/television technician
for additional suggestions. Also, the Federal
Communications Commission has prepared a
helpful booklet, "How To Identify and
Resolve Radio TV Interference Problems."
This booklet is available from the U.S.
Government Printing Office, Washington,
DC 20402. Please specify stock number 004000-00345-4 when ordering copies.
For Your Records
In the event that service should be required,
you may need both the model number. In
the space below, record the date and place
of purchase:
Date of Purchase:
Place of Purchase:
Service Information
This product should be serviced only by
those specially trained in appropriate
servicing techniques. For instructions on
how to obtain service, refer to the warranty
included in this Guide.
EN
FCC Information
WARNING: TO PREVENT FIRE
OR ELECTRICAL
SHOCK HAZARD,
DO NOT EXPOSE THIS PRODUCT
TO RAIN OR MOISTURE.
SEE MARKING ON BOTTOM / BACK OF PRODUCT
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
THE EXCLAMATION
POINT WITHIN THE
TRIANGLE IS A
WARNING SIGN
ALERTING YOU OF
IMPORTANT
INSTRUCTIONS
ACCOMPANYING
THE PRODUCT.
THE LIGHTNING
FLASH AND ARROWHEAD WITHIN THE
TRIANGLE IS A
WARNING SIGN
ALERTING YOU OF
"DANGEROUS
VOLTAGE" INSIDE
THE PRODUCT.
CAUTION: TO REDUCE THE
RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER
(OR BACK). NO USERSERVICEABLE PARTS INSIDE. REFER SERVICING
TO QUALIFIED SERVICE
PERSONNEL.
RCA
RP5030
Equipment tested for
compliance as a
complete unit
RCA
RP5035
Equipment tested for
compliance as a
complete unit
RP5030 EN (B ver) 15/11/06 1:44 PM Page 3
EN
FCC Information
Ecology
Help protect the environment - we
recommend that you dispose of
used batteries by putting them
into specially designed receptacles.
Maintenance
Clean the unit with a soft cloth,
or a damp chamois leather.
Never use solvents.
Precautions for the Unit
• Do not use the unit immediately after
transportation from a cold place to a
warm place; condensation problem may
be resulted.
•Avoid shock to the unit especially during
recording. Recorded data can be
damaged.
• Do not store the unit near fire, places
with high temperature or places with
direct sunlight.
• Do not operate or store unit in places
with frequent static electricity or
electrical noise (e.g. speaker, TV set).
•Clean the unit with a soft cloth or a
damp chamois leather. Never use
solvents.
• The unit must only be opened by
qualified personnel.
• Do not expose this appliance to rain or
moisture.
Precautions for Batteries
• If you do not use the unit for more than
one month, be sure to remove the
batteries to avoid leakage.
• When installing batteries, be sure that
the polarities are correct. Reversing
polarity may cause personal injury and
damage to the batteries.
• Never mix new batteries with old ones.
Do not mix battery types.
• Discard leaking batteries immediately.
Leaking batteries can cause skin burns or
other personal injury.
• Do not dispose of in fire.
• Do not charge batteries which are not
intended to be recharged.
Power Supply
• (battery power) 2 x “AAA”
ESD Remark:
In case of misfunction due to electrostatic discharge just reset the product (disconnect and
reconnect of the power source may be required) to resume normal operation.
RP5030 EN (B ver) 15/11/06 10:28 AM Page 4
FCC Information
Contents
General Controls . . . . . . . . . . . . . . .1
The Display . . . . . . . . . . . . . . . . . . .3
Display messages . . . . . . . . . . . . . .4
Before you begin . . . . . . . . . . . . . .5
Power supply . . . . . . . . . . . . . . . . . . .5
Installing Batteries (not included) . .5
Auto power shut down . . . . . . . . . . .5
Using headphones and external
microphone . . . . . . . . . . . . . . . . . . . . .5
Starting up/shutting down the unit 5
Keys Lock . . . . . . . . . . . . . . . . . . . . . . .5
Tones . . . . . . . . . . . . . . . . . . . . . . . . . .5
Setting the time . . . . . . . . . . . . . . .6
Year/Date/12/24/Time Setting . . . . . .6
Basic operation . . . . . . . . . . . . . . . .7
Select folder . . . . . . . . . . . . . . . . . . . .7
Select file . . . . . . . . . . . . . . . . . . . . . . .7
Normal Playback . . . . . . . . . . . . . . . . .7
Bookmark . . . . . . . . . . . . . . . . . . . .8
Creating a bookmark . . . . . . . . . . . . .8
Skipping to a bookmark . . . . . . . . . .8
Deleting a bookmark . . . . . . . . . . . . .8
Recording mode . . . . . . . . . . . . . . .9
Setting Recording mode . . . . . . . . . .9
Manual Recording . . . . . . . . . . . . . . .9
AVR (Automatic Voice Recording) . .9
Recording quality/condition . . . . .10
Other Functions . . . . . . . . . . . . . . .11
IntroScan . . . . . . . . . . . . . . . . . . . . . .11
Play one/play all . . . . . . . . . . . . . . . .11
Erasing file/folder . . . . . . . . . . . . .12
Erasing selected file . . . . . . . . . . . . .12
Erasing all files in a folder . . . . . . . .12
Advanced operation . . . . . . . . . . .13
Speed . . . . . . . . . . . . . . . . . . . . . . . . .13
Insert . . . . . . . . . . . . . . . . . . . . . . . . .13
Append . . . . . . . . . . . . . . . . . . . . . . .13
Cut . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Format . . . . . . . . . . . . . . . . . . . . . . . .14
Connecting to the Computer . . . .15
Install the USB Driver
(Windows 98SE Only) . . . . . . . . . . . .15
Plugged into the computer . . . . . .15
Disconnecting from the computer .15
Using your unit as a file storage
device . . . . . . . . . . . . . . . . . . . . . . . . .15
Transfer files via Windows Explorer
(Drag and Drop) . . . . . . . . . . . . . . . .15
Troubleshooting tips . . . . . . . . . . .17
Warranty . . . . . . . . . . . . . . . . . . . .18
EN
Contents
RP5030 EN (B ver) 15/11/06 10:28 AM Page 5
EN
1
General Controls
Recording
indicator
ERASE:
Erases file
MENU: Folder, record
condition, record
quality, AVR on/off,
play condition, beep
tone, set
year/day/12/24/time
Built-in
microphone
REC: starts /
pauses
recording.
STOP: stops
playback/
recording. Turns
off the unit.
PLAY: turns the
unit on. Starts/
pauses playback.
FORWARD: skips and
searches forward.
Selects/Browses
under menu mode.
REVERSE: skips and
searches backward.
Selects/Browses
under menu mode.
RP5030 EN (B ver) 15/11/06 10:28 AM Page 6
64M
DIGITAL VOICE RECORDER
ERASE MENU
EN
2
VOL UP:
Volume up
VOL DOWN:
Volume
down
:
keylock
on/off
External
microphone
jack
Connects
headphones
USB jack
RP5030 EN (B ver) 15/11/06 10:28 AM Page 7
MIC
EAR
EN
3
The Display
Folder (A/B/C/D/ )
File selected
Total number of
files in a folder
Bookmark
Play/record
Total
remaining
time for
recording
Playback
mode: Play
one/
Play all
Battery level
indicator
Key Lock
Time/date/
recorded time
AM/PM
Keytone
Recording
Conditions
Automatic
Voice
Recording
Recording
Qualities
RP5030 EN (B ver) 15/11/06 10:28 AM Page 8
BCD
A
FAST
SLOW
REMAIN
LP
MM
ONE
ALL
SP
BEEP
HQ
DD
DICT
CONF
AVR
AM
PM
EN
4
Display Messages
ALL
APPEND
CUT-E
CUT-S
DELETE
FULL
MM/DD
12 HOUR
24 HOUR
TIME
INSERT
INTRO
OFF
ON
SEN 07
TONE
NO TONE
VOL 15
YEAR
LOCKED
FORMAT
SPEED
WAIT...
001%
PAUSE
Select all (Introductory Play back & Erasing All Files)
Appendix (Adding Appendix)
Cut End (Cutting)
Cut Start (Cutting)
Delete (Erasing Selected File)
Memory full
Month / day entry mode.
12 hour time display mode.
24 hour time display mode.
Time entry mode
Insertion (Inserting New Segments)
Introduction (Introductory Playback)
Off (Automatic Voice Recording)
On (Automatic Voice Recording)
Sensitivity Level (AVR)
Beeping sound on(Setting Beep Sound)
No beeping sound (Setting Beep Sound)
Volume (Setting Volume)
Year (Setting Year)
Key locked
Format the memory
Speed of playback
Unit is busy
Formatting is in process
Playback paused
RP5030 EN (B ver) 15/11/06 10:57 AM Page 9
EN
5
Before You Begin
Power supply
This unit can be operated by 2
“AAA” batteries.
Installing Batteries (not
included)
1. Slide the battery compartment
door to the bottom and lift up the
door to open.
2. Insert 2 “AAA” batteries with
polarities matching indications.
3. Replace the battery compartment
door.
Refer to the battery level
indicator on display for
batteries level. Replace
with new batteries when
the indicator is empty.
Auto power shut down
The unit will be automatically turned
off if left idle for 3 minutes.
Using headphones and external
microphone
• When headphones are connected,
sound output from speaker will be
muted.
• When external microphone is
connected, no record can be made
from built-in microphone.
Starting up the unit
Press PLAY to turn on the unit to
start playback or recording.
Shutting down the unit
Press STOP to turn off the unit.
Keys lock
This feature avoids accidental key
activation during recording or
playback.
1. Slide the button upward ,
LOCKED will be flashed on display.
(LOCK icon will be shown)
2. Slide the button downward to
unlock the keys.
Tones
You can activate this
feature so that beep
sound can be heard
whenever you press on
any button except
during playback and
recording.
1. Press MENU button
repeatedly until
TONE shows on
display.
2. Press REVERSE or FORWARD to
set beep sound ON/ OFF.
3. Press MENU to confirm selection.
RP5030 EN (B ver) 15/11/06 10:28 AM Page 10
BEEP
BEEP
Year/Date/12/24/Time Setting
With this function, you can always
read on the display the recording date
and time of your recorded messages.
Follow the steps below for time
setting.
You can still use this unit for normal
recording without setting the time.
However, no correct recording date
and time can be referred for your
recorded messages.
1. Turn on the unit.
2. Press MENU repeatedly to enter
Time setting mode.
3. When “YEAR” flashes, the digits of
the year blinks (default is 2006).
Press REVERSE or FORWARD to
increase/decrease the number, press
MENU to confirm.
4. Once the year is
entered , the digits
in the month field
will blink (default is
1). Press REVERSE or
FORWARD to
increase/decrease the number, press
MENU to confirm.
5. Once the month is
entered, the digits
in the day will
blink(while the
digits in the month
field stop blinking).
Press REVERSE or
FORWARD to increase/decrease the
number, press MENU to confirm.
6. Once the date is entered, you can
choose between 12/24 hour clock
display by pressing REVERSE
/FORWARD, then press MENU to
confirm.
7. Once the time
format is entered,
the digits in the
hour field will blink
(default setting is 12
(12 hour mode) & 0
(24 hour mode). Press REVERSE or
FORWARD to increase/decrease the
number, press MENU to confirm.
8. Once the hour field
is entered, the digits
in the minute field
will blink. Press
REVERSE or
FORWARD to
increase/decrease the number, press
MENU to confirm.
EN
6
Setting the Time
Tip:
Press STOP to exit to Stop mode.
RP5030 EN (B ver) 15/11/06 10:28 AM Page 11
MM
DD
AM
AM
Select folder
You can select a specific folder (A, B,
C , D or ) for browsing. Default is
folder A.
1. Press MENU in stop
mode.
2. Folder A, B, C , D or
icon will blink
on display.
3. Press REVERSE or
FORWARD to
select a folder.
4. Press STOP to exit
to stop mode in the
desired folder.
Select file
You can select a specific file for
playback.
1. Select the folder you need.
2. Press REVERSE or
FORWARD to
select the file you
want. If the file you
want is in the
current folder, you
can press REVERSE or FORWARD
to select it directly in stop and play
mode.
Normal Playback
1. In Stop mode, select a folder (A, B,
C , D or ).
2. Select file by pressing REVERSE or
FORWARD.
3. Press PLAY to start playback.
4. Press PLAY to pause playback,
press again to resume.
5. You can press VOL UP (+) or VOL
DOWN (-) to adjust listening
volume.
6. Press and hold REVERSE or
FORWARD to make quick search
within a file.
7. Press REVERSE or FORWARD once
to skip one file forward or
backward.
8. Press STOP to stop playback.
EN
7
Basic Operation
Note:
• You can record up to 99 files in
one folder, not exceeding 396
files in total. When the maximum
limit is reached, “FULL” will show
on the display.
• You can find the files transferred
from computer in the folder.
See page 15 for details of file
transfer.
RP5030 EN (B ver) 15/11/06 10:28 AM Page 12
A
A
REMAIN
AM
DICT
ONE
SP
B
Creating a bookmark
This feature allows you to create an
interception point in the recorded
message for quick reference.
1. During playback, press REC once to
set a bookmark, the bookmark icon
flashes on the display.
2. You can create multiple bookmarks
until the memory is full.
Skipping to a bookmark
You can skip to a bookmark anytime
during playbcak.
1. During playback, press FORWARD
to go to the bookmark (if
available).
2. Press FORWARD or BACKWARD to
search different bookmarks of the
file.
Deleting a bookmark
1. Select folder (A, B, C , D or )
2. Select file.
3. Press ERASE once and DELETE will
blink on the screen.
4. Press and hold PLAY for 3 seconds
to confirm deleting. (or press STOP
to cancel erasing file)
EN
8
Bookmark
Tip:
• When the memory is full, “FULL”
will show on the display.
• If the file have multiple
bookmarks, steps 1-4 will delete
ALL bookmarks.
RP5030 EN (B ver) 15/11/06 10:28 AM Page 13
Setting Recording Mode
You can select between two
recording modes - manual recording
and AVR (automatic voice recording).
1. Manual Recording
1. In STOP mode, select folder (A, B,
C , D or ).
2. Press RECORD to start recording.
3. To pause recording, you can press
RECORD once, press again to
resume recording.
4. To stop recording, press STOP.
2. AVR (Automatic Voice
Recording)
This feature allows the unit to sense
sound and to record only when you
are speaking into the microphone.
When dictation stops for about 3
seconds, recording will stop and then
start again automatically when you
resume dictation.
1. Select destination folder (A, B, C ,
D or ).
2. Press MENU four times.
3. Press REVERSE or FORWARD to
toggle between AVR on and AVR
off.
4. Press STOP to exit to STOP mode.
5. Press RECORD to enter AVR mode.
6. During AVR on
recording, adjust
the sensitivity of the
microphone by
pressing VOL UP
and VOL DOWN,
SEN with sensitivity
value shows on
display (e.g.
increase sensitivity
value when
recording source is
far from the unit or
the recording
envionment is
quiet.).
7. Start dictation.
Recording starts
automatically.
8. Press STOP to end AVR recording.
9. Repeat step 2 and select AVR OFF
for de-selection.
EN
9
Recording Mode
Tip:
To view the remaining time and
other recording information, you
may press PLAY during recording.
Tip:
The first syllable or two may be
lost when you start recording
because this ‘sound’ is used to turn
on the AVR feature. It is a good
practice to make some ‘sounds’ or
say a short word to activate the
AVR before you begin actual
dictation.
RP5030 EN (B ver) 15/11/06 10:28 AM Page 14
A
AVR
AVR
AM
DICT
SP
AVR
Setting Recording Quality
You can select between three
recording qualities. Default is SP.
Definition
• SP (Standard Play) -
Model RP5030
allows about 520
minutes recording
while model RP5020
allows about 1040
recording
• LP (Long Play) -
Model RP5030
allows about 1040
minutes recording
while model RP5035
allows about 2080
minutes recording
• HQ (High Quality) -
Model RP5030
allows about 260
minutes recording
while model RP5035
allows 520 minutes
recording
1. Press MENU button three times,
(SP, LP or HQ show on display.)
2. Toggle between SP and HQ by
pressing REVERSE or FORWARD.
3. Confirm selection by pressing
MENU or STOP button.
Setting Recording Condition
You can select between two recording
conditions. Default is DICT.
Definition
• CONF (Conference) - in a more
open area and recording source is
far from the unit.
• DICT (Dictation) - in a more
enclosed area and recording source
is close to the unit.
1. Press MENU two
times until DICT or
CONF show on
display.
2. Select recording
condition by
pressing REVERSE or FORWARD.
3. Confirm selection by
pressing MENU
button. (You may
press STOP to exit
from further
selection.)
EN
10
Recording Quality / Condition
Tip:
For conferences, to obtain
optimum recording quality, place
the recorder with the microphone
freely exposed to the sound source
as close as convenient. A built-in
automatic recording level control
will set the optimum record level
during manual recording. Avoid
recording near unwanted noise
sources, such as air conditioners or
fans.
RP5030 EN (B ver) 15/11/06 10:28 AM Page 15
SP
LP
HQ
DICT
DICT
EN
11
Other Functions
IntroScan
This feature allows playback of the
beginning 3 seconds of each file in a
folder.
1. Select folder (A, B,
C , D or ) and
file.
2. Press REVERSE or
FORWARD until
ALL shows on
display
3. Press PLAY to start
introductory
playback, INTRO
shows on display.
4. Press PLAY to start
playing desired file.
5. Press STOP to exit Intro Scan
sooner.
Play one / play all
You can choose to play a specific file
or all files in a folder.
1. In STOP mode,
press MENU button
repeatedly until
ONE appears on
display.
2. Press REVERSE or
FORWARD to
toggle between
ONE and ALL.
RP5030 EN (B ver) 15/11/06 10:28 AM Page 16
A
A
DD
MM
AM
DICT
SP
DD
MM
SP
ONE
ALL
Erasing selected file
You can delete a file by the following
steps:
1. Select folder (A, B, C , D or )
2. Select file.
3. Press ERASE once and DELETE will
blink on the screen.
4. Press and hold ERASE for 3 seconds
to confirm deleting. (or press STOP
to cancel erasing file)
Erasing all files in a folder
You can delete all files in a specific
folder by the following steps:
1. Turn on the unit.
2. Select a folder (A, B, C , D or ).
3. In Stop mode, press FORWARD
continuously until “ALL” appears
on the display.
4. Press ERASE and “DELETE” will
blink on the display.
5. Press and hold ERASE for about 3
seconds, all files in the selected
folder will be erased completely (or
press STOP to cancel erasing all
files).
EN
12
Erasing File / Folder
Tip:
File numbers that come after
erased one will be moved forward
by one automatically.
RP5030 EN (B ver) 15/11/06 10:28 AM Page 17
EN
13
Advanced Operation
CAUTION
• The edit function does not operate
when battery power is too low or
the Introduction Mode is in used.
• After editing a message, “WAIT”
will be displayed. Do not power
off the device until “WAIT”
disappears.
Speed
You can adjust the playback speed.
1. Select folder.
2. Select file for
adjusting playback
speed.
3. Start playback.
4. Press PLAY to start
playback.
5. During playback,
press MENU once,
“SPEED” will be
shown on display.
6. Press REVERSE or FORWARD to
toggle between FAST and SLOW.
7. Press PLAY to confirm and exit.
Insert
You can insert new segments into a
file without erasing previously
recorded content.
1. Select folder.
2. Select file for inserting new
segment.
3. Start playback.
4. Press MENU twice
to start recording
new segment,
“INSERT” will be
shown on display.
Press RECORD within three
seconds.
5. Press STOP to stop recording.
6. “WAIT” will show on the display.
7. After the memory rearrangement
completed, the unit will go to
STOP mode.
Append
You can add appendix (e.g. reminder,
supplementary information) to the
end of the file.
1. Select folder.
2. Select file for
adding appendix.
3. Start playback.
4. Press PLAY to start
playback.
5. During playback, press MENU
three times, “APPEND” will be
shown on display.
6. Press RECORD within 3 seconds to
start recording appendix.
7. Press STOP to stop recording.
RP5030 EN (B ver) 15/11/06 10:28 AM Page 18
A
AM
ONE
SP
FAST
SLOW
A
AM
ONE
SP
EN
14
Cut
You can erase unwanted parts from
your recording.
1. Select folder.
2. Select file.
3. Start playback of
the file with the
unwanted part.
4. Press ERASE to
mark the start of
the unwanted part,
“CUT-S” shows on
display.
5. Press ERASE to
mark the endof the
unwanted part,
“CUT-E” shows on
display.
6. Press ERASE again to confirm
cutting (or press STOP to cancel)
7. “WAIT” will show on the display.
8. After the memory rearrangement
completed, the unit will go to STOP
mode.
Format (Caution! All data inside
the memory will be erased)
You can format the internal memory
when needed. (e.g. compatability
problem, etc.)
The procedures are as follow:
1. Turn on the unit.
2. Press ERASE, “DELETE” will flash
on the display.
3. Press and hold REC for 3 seconds,
“FORMAT” will flash on the display.
4. Press and hold ERASE, the
completed percentage will show on
the display, formatting is in process.
5. After the formatting is completed,
the remain time of the selected
memory will show on the display.
Tip:
Cutting, inserting new segments
and adding appendix will only
update the recorded time length,
without changing recording time
and date.
RP5030 EN (B ver) 15/11/06 10:28 AM Page 19
A
ONE
A
ONE
AM
SP
AM
SP
A
A
A
DICT
SP
DICT
SP
A
REMAIN
DICT
SP
DICT
SP
A
DICT
SP
Install the USB Driver (Windows
98SE Only)
For Windows 98SE system, you need
to install a USB driver before your
computer can recognize your player.
1. Download the driver for your
model from the following links:
Model RP5030:
http://www.rcaaudiovideo.com/enUS/Downloads.html?ProductID=RP5
030
Model RP5035:
http://www.rcaaudiovideo.com/enUS/Downloads.html?ProductID=RP5
035
2. Open the downloaded file
(RP503x_Win98Drv.exe) and follow
the on-screen instruction.
3. After installation is completed,
reboot your computer.
Plugged into the computer
You can transfer files with computer
via USB connection.
1. Use the USB cable supplied to
connect the unit to the computer.
2. “PC-LINK” will show on the display.
3. The unit may appear to be a
removable drive in your computer.
Disconnecting from the
computer
Unplug the USB cable after you have
copied files to or from the unit.
EN
15
Connecting to the Computer
Tip:
• Data transfer is possible even if
no batteries are installed in the
unit.
• On some operating system, a
message warning about
"Removing a USB device without
stopping it…" might appear, you
can press OK to safely ignore it.
RP5030 EN (B ver) 15/11/06 10:28 AM Page 20
EN
16
Using your unit as a file storage
device
The unit can function as a detachable
data storage. You can take along
your favorite images and documents
wherever you go. Simple cut-andpaste or drag-and-drop files to or
from it via USB connection, the unit
will appear as a removable disk in
Windows Explorer.
Transfer Files via Windows
Explorer (Drag and Drop)
Your player is associated with a drive
letter. From Windows Explorer,
highlight all the files/folders you
want to transfer to your Player and
drag them to the folder named
“MUSIC” in the drive. Your files can
be found in this folder in the Player
once it is disconnected from the
computer.
RP5030 EN (B ver) 15/11/06 10:28 AM Page 21
Unit doesn’t turn on
• Check that batteries are properly
inserted and not exhausted.
• Make sure battery compartment
door is properly closed.
• Make sure LOCK function is not
activated.
Display keeps flashing when unit
is off
•You may not have set the time.
Refer to section on Time Setting.
Cannot record
• Make sure LOCK function is not
activated.
• Make sure memory is not full.
•You have recorded 99 files in one
folder. Try record in a new folder.
Cannot show recording date and
time during playback
•You may have not set the date and
time before recording. Refer to
section ‘Time Setting’.
No sound from speaker during
playback
• Make sure volume is not set to 0.
• Headphones should not be
connected.
Cannot edit
• Make sure LOCK function is not
activated.
Cannot activate the unit after
pressing on keys
• There may be software problems.
Remove the batteries to reset the
unit.
Recordable time becomes shorter
•You may have set the recording
quality to ‘High Quality’, refer to
section ‘Setting Recording
Quality’.
Cannot perform playback
• Make sure you have selected
folder with recorded messages.
• Make sure LOCK function is not
activated.
Cannot erase recorded file(s)
• Make sure you follow each step
under section “Erasing Selected
File” carefully.
Cannot stop recording when AVR
ON
• If AVR ON sensitivity is too high
(e.g. 8 - 10), recording may not be
stopped in noisy environment.
Cannot keep the saved setting
• If the batteries are removed, saved
settings may be removed.
EN
17
Troubleshooting Tips
RP5030 EN (B ver) 15/11/06 10:28 AM Page 22
EN
18
U.S. limited warranty
What your warranty covers:
• Defects in materials or workmanship.
For how long after your purchase:
• One year from date of purchase.
The warranty period for rental units begins with the first rental or 45 days from date
of shipment to the rental firm, whichever comes first.
What we will do:
• Provide you with a new, or at our option, a refurbished unit. The exchange unit is
under warranty for the remainder of the original product’s warranty period.
• Proof of purchase in the form of a bill of sale or receipted invoice which is evidence
that the product is within the warranty period must be presented to obtain
warranty service. For rental firms, proof of first rental is also required.
How to make a warranty claim:
• Properly pack your unit. Include any cables, etc., which were originally provided
with the product. We recommend using the original carton and packing materials.
• Include evidence of purchase date such as the bill of sale. Also print your name and
address and a description of the defect. Send via standard UPS or its equivalent to:
Thomson Inc.
Product Exchange Center
11721 B Alameda Avenue
Socorro, Texas 79927
• Insure your shipment for of loss or damage. Thomson accepts no liability in case of
damage or loss en route to Thomson.
• Pay any charges billed to you by the Exchange Center for service not covered by the
warranty.
• A new or refurbished unit will be shipped to you freight prepaid.
What your warranty does not cover:
• Customer instruction. (Your Owner’s Manual provides information regarding
operating Instructions and user controls. For additional information, ask your
dealer.)
• Installation and set-up service adjustments.
• Batteries.
• Damage from misuse or neglect.
• Products which have been modified or incorporated into other products.
• Products purchased or serviced outside the USA.
• Acts of nature, such as but not limited to lightning damage.
RP5030 EN (B ver) 15/11/06 10:28 AM Page 23
EN
19
U.S. limited warranty
Limitation of Warranty:
• THE WARRANTY STATED ABOVE IS THE ONLY WARRANTY APPLICABLE TO
THIS PRODUCT. ALL OTHER WARRANTIES, EXPRESS OR IMPLIED (INCLUDING
ALL IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A
PAR TICULAR PURPOSE) ARE HEREBY DISCLAIMED. NO VERBAL OR WRITTEN
INFORMATION GIVEN BY THOMSON INC., ITS AGENTS OR EMPLOYEES
SHALL CREATE A GUARANTY OR IN ANY WAY INCREASE THE SCOPE OF THIS
WARRANTY.
• REPAIR OR REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS THE
EXCLUSIVE REMEDY OF THE CONSUMER. THOMSON INC. SHALL NOT BE
LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING FROM
THE USE OF THIS PRODUCT OR ARISING OUT OF ANY BREACH OF ANY
EXPRESS OR IMPLIED WARRANTY ON THIS PRODUCT. THIS DISCLAIMER OF
WARRANTIES AND LIMITED WARRANTY ARE GOVERNED BY THE LAWS OF
THE STATE OF INDIANA. EXCEPT TO THE EXTENT PROHIBITED BY
APPLICABLE LAW, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR
FITNESS FOR A PARTICULAR PURPOSE ON THIS PRODUCT IS LIMITED TO THE
APPLICABLE WARRANTY PERIOD SET FORTH ABOVE.
How state law relates to this warranty:
• Some states do not allow the exclusion nor limitation of incidental or
consequential damages, or limitations on how long an implied warranty lasts, so
the above limitations or exclusions may not apply to you.
• This warranty gives you specific legal rights, and you also may have other rights
that vary from state to state.
If you purchased your product outside the USA:
This warranty does not apply. Contact your dealer for warranty information.
RP5030 EN (B ver) 15/11/06 10:28 AM Page 24
EN
20
Canadian limited warranty
Thomson multimedia Ltd. warrants to the purchaser or gift recipient that if any
manufacturing defect becomes apparent in this product within 1 year from the
original date of purchase, it will be replaced free of charge, including return
transportation.
This warranty does not include damage to the product resulting from accidents,
misuse or leaking batteries.
Should your product not perform properly during the warranty period, either:
1. Return it to the selling dealer with proof of purchase for replacement,
OR
2. Remove the batteries (where applicable), and pack product complete with
accessories in the original carton (or equivalent). Mail prepaid (with proof of
purchase) and insured to:
Thomson multimedia Ltd.
6200 Edwards Blvd.,
Mississauga, Ontario L5T 2V7
Canada
The provisions of this written warranty are in addition to and not a modification of or
subtraction from the statutory warranties and other rights and remedies contained in
any applicable legislation, and to the extent that any such provisions purport to
disclaim, exclude or limit any such statutory warranties and other rights and
remedies, such provisions shall be deemed to be amended to the extent necessary to
comply therewith.
If you are unable to find a qualified servicer for out of warranty service, you may
write to:
Thomson Inc.
P. O. Box 0944
Indianapolis, Indiana, U.S.A., 46206-0944
Attach your sales receipt to this booklet for future reference. This information is
required if service is needed during the warranty period.
PURCHASE DATE
NAME OF STORE
RP5030 EN (B ver) 15/11/06 10:28 AM Page 25
Thomson Inc.
P.O. Box 1976, Indianapolis, IN 462061976
©2006 Thomson Inc.
Trademark(s) © Registered
Marca(s) © Registrada(s)
Marque(s) © Deposée(s)
www.rca.com
Printed in China/Impreso en China
5629403B (EN/F/E)
Comercializadora Thomson de México, S.A. de C.V.
Álvaro Obregón No. 151. Piso 13.
Col. Roma. Delegación Cuauhtémoc
C.P. 06700. México, D.F.
Telefono: 52-55-11-020360
RFC: CTM-980723-KS5
RP5030 EN (B ver) 15/11/06 10:28 AM Page 1
Loading...