RCA 50LB45RQ Schematic

For qualified service personne_ only
Version 1,,0 for 2012

Mode_,
50LB45RQ

Made for Today.

www.rca.com

Revision No. Revision Date Page Description
1 May, 2012 All Initial Release

Version 1.0

1.1 Basic Specifications

Diagonal Display Size
Television System
Channel Coverage

Temperature

Humidity

Power Supply

RF input

Connection

Interface

Video input

Audio input

Audio output
Graphic input

Resolution

Component/HDMI mode

With stand

Dimensions

Without stand
With stand

Weight

Without stand

Power Consumption

50 inches
American TV standard ATSC/NTSC system

VHF:2-13 UHF:14-69 CAW:1-135

Storage Temperature is -20°C-+60°C (-4°F-+140°F)
Operating Temperature is 0°C-+50°C (+32°F-+122°F)
Storage Humidity: Less than 85% RH (No condensation)
Operating Humidity: Less than 80% RH (No condensation)
AC 100-120V, 60Hz
Cable/Antenna x 1
AVx 1

Component x 1
HDMI x 4
AVx 1

Component x 1
PC Audio In x 1

Headphone x 1, Digital Audio Out x 1, Analog Audio Out x 1
RGB 15pin x 1

1920 x 1080

480i, 480p, 720p, 1080i, 1080p

45.9W x 30.4H x 12.2D

45.9W x 28.7H x 4.2D

51.1 LBS (23.2KGS)

42.3LBS (19.2KGS)
less than 150W

Version 1.0

1

1,2 Product Function

Side Keypad Buttons

If you cannot locate your remote, you can use the side keypad buttons on your TV to operate many TV features.

INPUT: Displays the Source Select List.
MENU: Displays the TV Main Menu.
OH ,, : Scans up through the channel list. In the TV menu system, it acts like the up arrow on the remote control and

can be used to select menu options.

OH ,, : Scans down through the channel list. In the TV menu system, it acts like the down arrow on the remote control

and can be used to select menu options.

VOL+: Increases the volume. In the TV menu system, it acts like the right arrow on the remote control and can be used

to select menu options.

VOL-:Decreases the volume. In the TV menu system, it acts like the left arrow on the remote control and can be used

to select menu options.

POWER (O): Turns the TV on and off.

Front Panel
Power/Standby Indicator: Blue and red dual-color LED. Itshows red when the TV isturned off and blue when turned on.

Remote Control Sensor: Remote control IRsensor, which receives infrared ray sent by remote control.

_! Remote Control Sensor

Power/Standby Indicator

(blue/red)

For more information about TV function, please refer to the User's Manual.

Version 1.0

2

1.3 Connection Interface

@ @

HEAD PHONE: Connect a 3.5mm headphone for personal audio.
Digital Audio-out: Connect a coaxial cable for digital audio output.
HDMI1, 2, 3, 4: (High-Definition Multimedia Interface) It provides an uncompressed digital connection that
carries both video and audio data by way of an integrated mini-plug cable.
AUDIO OUTPUT L/R: Connect double-channel coaxial cables for analog audio output.

Note: Di!(yt,_lAuo'/_;,-out _nd AUDIO OUYT:_UY ,_resupf._osed to be connected to <_udk:;,povvey

ampfific;_ which prot_'des smoolher _<r_ndmorn powerful sound perfc,rmance.
AUDIO-IN L/R, Video In: Connect an AV device that has composite video jacks, such as a VCR
or a DVD player. To access device connected to these jacks, press the INPUT button on your
remote; then press the up/down arrow to select AV. Press the ENTER button at last to confirm.

• AUDIO-IN L: Left audio channel connection. The left audio connector is usually white. For mono audio
sources, be sure to use the left AUDIO INPUT.

,, AUDIO-IN R: Right audio channel connection. The right audio connector is usually red.
COMPONENT Y/Pb/Pr: Connect a device that has component video jacks, such as a DVD player.
To access device connected to the Y/Pb/Pr jack, press the INPUT button on your remote; then press the up/down arrow to
select Component. Press the ENTER button at last to confirm.

,, Y/Pb/Pr (Component Video): They provide good picture quality because the video signal is separated into three
components. Use three video-grade or component video cables for the connection. When using Y/Pb/Pr, make sure you
connect left and right audio cables to the Audio L and Audio R jacks.

PC INPUT VGA: Connect your computer or other device with a VGA output to this jack using a 15-pin, D-sub cable.
PC INPUT Audio-In: Use to obtain sound when a PC is connected to TV. Use 3.5mm stereo mini-pin cable to connect PC to TV.
ANT/CABLE: Connect to receive the signal from your antenna or cable via coaxial cable.
SERVICE: For service use only. Do not connect any device.

Version 1.0

3

2.1 General Information

GENERAL DESCRIPTION

OVERVIEW

V500HJI-L01 is a 50 TFT Liquid Crystal Display module with 12-CCFL Backlight unit and 2ch-LVDS interface.
This module supports 1920 x 1080 Full HDTV format and can display 16.7M colors (8-bit). The inverter module
for backlight isnt built-in.

FEATURES

- High brightness (350 nits)

-- High contrast ratio (4000:1)

-- High color saturation (NTSC 72%)

-- Fast response time (Gray to gray average 8 ms)

- Full HDTV (1920 x 1080 pixels) resolution, true HDTV format

-- DE (Data Enable) only mode

-- LVDS (Low Voltage Differential Signaling) interface

-- Optimized response time for 60 Hz frame rate

-- Ultra wide viewing angle : Super MVA technology

-- Rolls compliance

GENERAL SPECIFICATIONS

Item

Active Area

Bezel Opening Area
Driver Element
Pixel Number

Pixel Pitch(Sub Pixel)
Pixel Arrangement

Display Colors
Display Operation Mode

Surface Treatment

Specification

1095.84(H) x (V) 616.41 (50 diagonal)

1102.84(H) x 623.41(V)

a-si TFT active matrix

1920 x R.G.B. x 1080

0.1903(H) x 0.5708(V)
RGB vertical stripe

16.7M

Transmissive mode / Normally Black
Anti-Glare coating (Haze 3.5%),Hardness 3H

Unit

am
mm

pixel

am

color

Note

(1)

(3)

Note (1) Please refer to the attached drawings in chapter 9 for more information about the front and back outlines.
Note (2) Please refer sec 3.1 and 3.2 for more information of Power consumption
Note (3) The spec. of the surface treatment is temporarily for this phase. CMI reserves the rights to change this feature.

Version 1.0

4

3.1 Inner Structure

Inside cabinet (front)

2

4

3

5 5

Version 1.0

5

Item List

1 RE32185B050 IR board 22F, 38.5X12.3X1.6mm (1)

2 RE0340E011 Key board 22F, 107X12X1.6mm (2)

3 RE01 TC81ELNA0 Main board T.RSC8.1E

(It is for version 2012)

4 RE46DZ2009 Power board IPB539 200W

5 RE261530458105 Speakers 8Ohm, 10W

Note: (1,2) 22F and dimensions refer to the PCB board.

3.2 Main board connection

CN9 CN17 CN25

CN5

CNA3

CNA1

(Continued in next page.)

Part NO.

Version 1.0

6

Jack List

Jack N01 1 Specification Description connection Note

CN25 10 Pin 2.54mm Main power To Power board

CN17 2x20 Pin 2,0ram LVDS interface To LCD panel

CN9 14 Pin 2.0mm IR and keyboard jack To IR board and keyboard

CN5 6Pin2.0mm Inverter Jack To LCD panel inverter board Backiightcontrol

C NA3 4 Pin 2.54mm Amplifier power supply jack To power board

CNA1 4 Pin 2.54mm Speaker jack To Speaker

3.3 Power board connection

CON5

CO

CON1

Jack List

Jack No.

CON1

CON5

CON2

CON3

CON2 CON3

specification, DeScdPt!0n connecti0n, NOte

2 Pin 3.96mm AC input lack To AC power supply

12Pin 2.0mm Backlight pcwersupFty To panel

10Pin 2.54mm Main board power supply To main board

4 Pin 2.54mm To main board

CON4 3Pin 2.0mm Backlight control jack To panel

Version 1.0

7

3,4 Connection Diagram

12Pin flat cable ..... 4

CON5

;u _ CON4

_o

8o

_ _ CON3 _

© O

_ CON2

CON1

8Pin flat cable

50" LCD panel

Keyboard

J

J \

7

4Pin to 4.Pin

J _

AC 100o120V
60Hz

@

C
c

Z

LVDS double array cable

3Pin to 6Pin flat cable

flat cable

'i

10Pin to 10Pin flat cable

IR board

5 Pin flatcable

4 Pin flat cable °°°,

CN17

CN5

CNA3
CN25

CN9

CNA1

©

oa
o

oq

©

O9

@

O9

o

Z
uJ

oo

©
b-

o

uJ

rY

E]_ Left speaker

[_ R_ght

Version 1.0

8

Note: Before opening the cabinet and working on the repairs, please read the troubleshooting and Q&A attached in the

user's manual, which has covered most of the problems caused by unproper using or settings to the TV set. Ifthat does not
work, please carry out the easy troubleshooting before checking or replacing the main parts of the television. The
troubleshooting guides given below base on the situation in which the TV's functions are set and used properly.

Plus, if the easy troubleshooting can not help, please work on the repairing according to the procedures given inchapter 5,
Exception Handles.

4.1 Troubleshooting for Common Use

TV can not be turned on

• Check the connection and condition of wires and inlets that relate to power board, including the AC power inlet, the
power incoming wire, wires between power board and mainboard, etc.

o Check the diagram arround power board to see If there exists a short circuit or creepage.

• The power board may be bad. Please change the board for testing. If it cannot help, refer to the chapter 5 for more
intensive information.

• In addition, the malfunction of LCD panel can cause failure of power on. Please refer to 4.2 Troubleshooting for Displaying
for more information.

Auto turning off

o Check the sleep timer setting.

• Check the surrounding diagram of power board. The problem is most possibly caused by short circuit or wire breakage,
because this kind of malfunctions can cause excessive current, which will make the power board startup self-protection.

The screen goes black after a shorting blink

e If the TV screen can not display after the blink, that means the panel or other parts of equipment is broken (most likely by

unproper input voltage). Ensure the input voltage of every component, and then check the part that is suspected damaged.

o If this problem occurs repeatedly, check the surrounding diagram and connections of panel inverter board. Also, the

blacklight unit and LCD lamps should be checked out.

There exists afterimages after power off

• If the panel can work normally at the other time, it may be caused by bad mainboard. Upgrade to the latest software first,
if that does not work, attempt to change the mainboard.

There exists squeak when TV is working

e IListen to the squeak carefully to make sure where the noise comes from. If it is from speakers, the voice may be caused by

bad speakers. Change them for a try..

• If the noise comes from the inner parts of cabinet, it may be produced by abnormal AC current in power board. Change the
board and check its surrounding circuits for a try.

• Check the routing of wires inside the cabinet to suppress interference.

Version 1.0

9

4.2 Troubleshooting for Displaying

Note: Ifthe troubleshooting given below can not help you, change the LCD panel for a try. But we strongly suggest you

regard changing the panel as the last step of fixing the display problem.

No display (including white screen, black screen, etc.)

• Check the power board output and main board input ports to make sure whether the TV has been turned on successfully,
because the failure in power on can lead to a no-display problem.

o If it is proved to have been electrified and turn on, check the LVDS cable first.

• Check if both of the two plugs of the flat cable between mainboard and power board have been well inserted into the slots.
Unstable power supply can also cause serious display problem.

• If the display problem only happens in one input mode, that may be caused by wrong version software. Update the new
software. If that can't help, change the main board for a try.

Screen tearing, or there exists moire on screen

• Bad LVDS cable and inappropriate panel driving voltage is still the biggest factor of this problem. So check them first.

e If the cable and voltage are correct, update the software for a try.
o Sometimes the fastening pieces can make unproper pressure to LCD panel, check them out.

• If the screen tearing happens in one or several input sources while the other source can display normally, it can be caused
by bad mainboard most likely. Please change the mainboard for a try.

• Refer to chapter 5 for more details and resolution ways.

Straight darWlight line(s) on screen

• If the bad line is very narrow, it is usually caused by LCD panel malfunction, change the panel for a try.

• If the lines link together and become a bad band, upgrade the software and then check the ports abd circuits of broken-

down output mode(s).

e If the darWlight line ,or band, apprears in all the input modes, please change the LCD panel. But we suggest you check the

panel inlet board(which links the panel and mainboard though LVDS cable) first, because sometimes the liquid crystal
displaying unit is okay, while the inlet board has a transmitting problem, which also will lead to a displaying failure.

• Refer to chapter 5 for more details and resolution ways.

Color cast or interference

• If the cast or interference happens in only one input mode, check the output port(on mainboard) and transmitting network
(arround mainboard) of that mode.

• If the cast or interference happens in all the input modes, please exclude the malfunction according to easy troubleshooting
for No Display. If that can not help, refer to chapter 5 for more details and resolution ways. In addtion, most of this kind of
problems come from the bad mainboards.

Version 1.0

10

4.3 Troubleshooting for Audio

Note: Comparing with the display problem, the audio malfunctions are easier to work out. Constantly, if you have excluded
the possibility of bad speakers and bad connection of audio output, the problem generally comes from the audio processing
parts of mainboard. Please change mainboard for a try, or refer to chapter 5 for further information about repairing.

No Sound

o Check whether the speakers are broken first.

o Check the wire that links the mainboard and speakers. Watch if there is fracture or cladding material breakage.

• Check the joint of speakers and audio wire, watch if there is poor soldering or fake solder. Besides, the polarity mistake
can also lead to audio problem.

Volume too low

o Check whether there is a jam at the sound hole in front cabinet.

• Check whether one or more speakers are bad.

Sound channel loss or confounding

• Check whether the audio wires are installed reversedly. The left channel wire should be white and the right channel wire
is red.

• Check the audio output socket of mainboard to see whether it is wrongly inserted. If not, the mainboard audio output module
may be bad, refer to chapter 5 for more details and resolution ways.

• If the connection is stable and right, the mainboard audio output module may be bad, refer to chapter 5 for more details
and resolution ways.

Noise

o Check ifthere is anything should not exist inthe speaker hollow space (such as screws).

• Check if the antihunting EVA is broken or missing.

• Check if the speakers are bad.

4.4 Troubleshooting for Keyboard

No key can work

e Check the wire between mainboard and keyborad, watch if there is fracture or cladding material breakage.

• Check the joint of mainboard and keyboard wire, watch if there is poor soldering ofrfake solder.

• Check the resistances that locate on the keyboard PCB. Watch ifthere is wrong or broken ones. Also, the poor soldering
of fake solder should be concerned and checked carefully.

o Check the other components of keyboard(such as capacitances and microswithes) are wrong or bad.

Version 1.0

11

Keys are sunken

• Check the screws that fasten the keyboard to the cabinet. They may be lost or getting loose.

• The key set may be bad, change them.

There is a reacting delay when operating the keys

o That is usually caused by bad keyboard, change it for a try.

Functions of keys are out of order

o Check the keyboard to see whether there is a short circuit between each soldering joint.

• Check all the resistances on PCB board.

o If a key is supposed to be able to achieve more than one functions, but it can achieve not all of them, that is usually

caused by wrong software. Please update the latest and correct software for a try.

• If you can't ensure where the problem comes from, change the keyboard for a try. If that still can't help, refer to chapter 5
for more details and resolution ways.

4.5 Troubleshooting for Remote Control

Note: If the troubleshooting can not help, please change the RC board. If that still can't solve the problem, please refer to
chapter 5 for more details and resolution ways with a will to mainboard repairing.

The RC (remote control, the same below) does not work

• Check the wire between mainboard and RC board, watch ifthere is fracture or cladding material breakage.

• Check the joint of mainboard and RC board wire, watch if there is poor soldering or fake solder. Also, the short circuit
can lead to this problem, too.

o Check the infrared senser that locates on the keyboard PCB. Watch if it is wrong or broken. Also, the poor soldering of

fake solder should be concerned and checked carefully.

• Check the other components of RC board are wrong or bad.

The LCD displays light in wrong color

• The short circuit is the most probable causation factor of this proble. Check the wire and joints for a judgement.

• Check the cable that links mainboard and RC board, watch if it is inserted with wrong location(similar with left-right channel
wire fault for audio).

o Check the LCD assembling, watch if its pins are in wrong location.

Version 1.0

12

Note: The exception handles are prepared for qualified personal only.

5.1 Display Exceptions

5,1.1 Black screen and no display

Note: Ifthe troubleshooting guide can not help you with the obviation of faults, please change the non-conforming

materials to rework.

Check the external

power supply

No

No _ Yes

No _[s the power system _ Yes

Check and repair

the power module NO

signal of

380-400MHZ on

R140

N©

IsY1 or Flash(U16)

ReplaceY1 or FLASH

(U16) orQ23 NO

,L

Replace the broken

component

Yes Yes

Yes

Replace DDR

(U17)or the

main chip (U8)

Version 1.0

13