START
GUIDE
Choose Your Connections
VIDEO
Quality Connects to... Cables needed (not included)
Audio
Video
R-AUDIO-L
Devices with Video (composite)
outputs, such as VCRs, Cable
Boxes, Satellite Receivers,
Camcorders, and Digital
Cameras
C R T P R O D U C T
Devices with Y Pb Pr
(component) outputs, such as,
DVRs, Satellite Receivers, and
Cable Boxes (Progressive Scan Set
Top Boxes- refer to the note below).
Pr
Pb
Y
Component
Video
Audio
Jacks
COMPOSITE (VID) INPUT
R-AUDIO-L
COMPONENT VIDEO
(CVID) INPUT
Connect a Signal Source
Cable Box, Satellite
Receiver, or Wall Outlet
OUT TO TV
or
TV
(Back Panel)
Outdoor Antenna
Indoor Antenna
-OR-
ANTENNA/CABLE
INPUT
(DIGITAL/ANALOG)
TV
(Back Panel)
ANTENNA/CABLE
INPUT
(DIGITAL/ANALOG)
Make your connection decision easier by taking a few minutes to review the jacks on your new
product. Compare the jacks on the device you want to connect and see if the same jacks are
available on your TV/DVD player. Then refer to the chart below to determine the best connection
to make.
For more information about connecting your product to other devices, refer to the User’s Guide
www.rca.com/television
Remember: The Component (CVID) and the Composite (VID) jacks share the same R/L Audio jacks shown above.
Notes: Coaxial and Audio/Video output jacks can be found on the back panel of your product. The DVD DIGITAL AUDIO OUT jack can be
connected to an audio reciever. View this connection when in DVD mode. More information can be found in your User’s Guide.
If you aren’t getting a picture while using the component connection (above), check the connected device (for example, cable or satellite set
top box). You need to change the setting on the device from progressive to interlaced (480i). Refer to the User’s Guide for more information.
that can be found in the support section on www.rca.com/television. Make sure you read the
safety information provided separately before you connect and operate your product.
RCA and associated marks are trademarks of THOMSON S.A. used under license to TTE Corporation.
Manufactured under license from Dolby Laboratories.
We help improve our environment by printing only this one page of instructions. The complete User’s Guide is available at the support section on
www.rca.com/television.
Español- Ayudamos a mejorar nuestro ambiente imprimiendo sólo esta página de instrucciones. La Guía de Inicio Rápido en Español y la Guía del
Usuario completa se encuentran disponibles en la sección de soporte en www.rca.com/television.
Français- Nous aidons à améliorer l’environnement en imprimant cette seule page d’instructions. Le Guide de démarrage rapide et le Guide de
l’utilisateur sont disponibles en Français dans la section du soutien, sur le site Web www.rca.com/television.
Connect your TV/DVD player to cable; a cable box or
satellite receiver; or an antenna in order to receive TV
channels. Connect the cables as shown in the rst or
second connection.
If you’re connecting a cable box or satellite receiver
and it has Component jacks (Y Pb Pr), connect the
cable box or satellite receiver to your product using the
Component jacks (CVID) for a better connection.
Continue to Step 2, Set Up Your Product, on the back
page.
Set Up Your Product
First, make sure you have connected your TV/DVD player to any devices, connected a signal source,
TV MENU
INPUT
DIG•ANA
TV•DVD
OPEN•CLOSE
DVD
SETUP
Operate Your Product
SETUP
Go back
Auto Channel Search
List & Labels
Closed Caption
Favorite Channel
Language Eng.
Format Normal
Auto Vol. Level Off
AUTO CHANNEL SEARCH
Go back
Source Type Cable
Start Search
plugged it into an electrical outlet, and put batteries in the remote.
• Now, turn on the TV/DVD player and begin the setup.
• Set the TV Menu Language. The default menu language is set to English. (The TV should already
be in TV mode. If not, press the TV/DVD button). Press the TV MENU button, highlight Setup, then
press OK. Go to Language and press the right arrow button to choose a language. Press TV MENU to
return to the previous menu or press CLEAR to exit.
• Set the Signal. From the Setup menu, highlight Auto Channel Search and press the right arrow
button. Source Type is highlighted. Press the right arrow button to select Antenna or Cable. Press the
down arrow button to highlight Start Search.
• Search Channels. Press the right arrow or OK button to start the channel search. When searching for
cable channels, this step can take some time. Your TV tunes to a channel once the search is complete. Go
to the next step to delete unwanted channels, or go Step 3 Operate Your Product for more information.
• Deleting Channels. After running the channel search there might be channels you don’t want in
the channel list. To delete a channel, press TV MENU, press the down arrow button to highlight Setup,
and press OK. Highlight List & Labels and press OK. Select Channel and press the right arrow button
to select the channel. Highlight In List and press the right arrow button to uncheck the box. Repeat to
delete other unwanted channels. Press CLEAR to exit.
Remember: The DIG•ANA
button switches between analog
or digital TV channels. Analog
channels are sent in a 4:3
(Standard) format. Most digital
channels are sent in a 16:9
(Widescreen) format.
Thank you for your purchase. Before making a trip back to the retailer, please visit www.rca.com/television for more information or contact us at
1-800-336-1900 so that we may assist you in operating your product, replacing missing parts, and ensuring your satisfaction.
Using the Remote
The remote control contains buttons that are dual purpose depending on which function (TV or DVD)
is being used. Use the TV/DVD button to switch between modes (i.e. TV mode or DVD mode). Green
button labels indicate DVD functions.
Viewing Devices Connected to Your Product
To view devices connected to your TV/DVD player, use the INPUT button (on the remote or front
panel) until the input name appears that matches the input of the device you connected. Your choices
are FRNT (side input), VID (composite input), CVID (component input), DVD (DVD content), digital
channel or analog channel.
Using the Menu Systems
To access the TV’s menu system, press the TV MENU button. To access the menus in the DVD player,
press the DVD SETUP button. Press the TV/DVD button to switch between modes. Use the arrow
buttons to navigate and the OK button to change selections.
Load and Play a Disc
• Press the TV/DVD button on the remote to make sure the unit is in the DVD mode.
• Press the SLEEP• (OPEN/CLOSE) button on the remote to open the disc tray. Place a disc gently
into the tray with the disc’s label facing up (double-sided discs have content on both sides, so you can
place either side up).
• Press the SLEEP• (OPEN/CLOSE) button again to close the disc tray. The player reads the disc’s
table of contents. What happens next depends on how the disc was programmed.
For more information on features, refer to the User’s Guide that can be found in the support section on
www.rca.com/television.
TOCOM 16756370
Loading...