Razor Trikke E2 Owner's Manual

Owner’s Manual

US_121210

NOTE: Manual illustrations are for demonstration purposes only.
Illustrations may not reflect exact appearance of actual product.

Specifications subject to change without notice.

Please have your 19 character product I.D. code ready before

contacting Razor for warranty assistance and/or replacement parts.

Product I.D. Code: _____________ - ____________ - ____________

Read and understand this entire manual before

allowing child to use this product!

For assistance contact Razor. DO NOT RETURN TO STORE.

NOTE: The Trikke E2 must be traveling up to 3 mph before motor will engage. Kick

start up to 3 mph while applying the throttle to engage motor.

1

WARNING: Riding a Razor Trikke™ E2 electric product does present
potential risks and caution is required. Like any riding product, this product has
inherent hazards associated with its use (for example, falling off or riding it into
a hazardous situation). Like any riding product, the Razor Trikke E2 is intended to
move and it is therefore, of course, possible to lose control or otherwise get into
dangerous situations. Both children and adults responsible for supervising them
must recognize that if such things occur, a rider can be seriously injured or die,
even when using safety equipment and other precautions. RIDE AT YOUR OWN
RISK AND USE COMMON SENSE.

WARNING: PARENTAL AND ADULT RESPONSIBILITY AND
SUPERVISION IS NECESSARY: Because products like this can and do present

potential hazards plainly associated with their use, it is well recognized THE
NEED FOR EXERCISE OF PARENTAL RESPONSIBILITY IN SELECTING RIDING
PRODUCTS APPROPRIATE TO THE AGE OF A CHILD, OR PARENTAL SUPERVISION
IN SITUATIONS IN WHICH CHILDREN OF VARIOUS AGES MAY HAVE ACCESS TO
THE SAME RIDING PRODUCTS, IS IMPORTANT. Not every product is appropriate
for every age or size of child, and different age recommendations are found within
this category of product which are intended to reflect the nature of the hazards and
the expected mental or physical ability, or both, of a child to cope with the hazards.

The recommended rider age is 8 and older. Any rider unable to stand
comfortably on the product should not attempt to ride it. A parent’s decision to
allow his or her child to ride this product should be based on the child’s maturity,
skill and ability to follow rules.

Keep this product away from small children and remember that it is
intended for use only by persons who are, at a minimum, completely
comfortable and competent while operating the product.

Persons with any mental or physical conditions that may make them susceptible
to injury, impair their physical dexterity or mental capabilities to recognize,
understand, and follow safety instructions and to be able to understand the hazards
inherent in its use, should not use or be permitted to use products inappropriate for
their abilities. Persons with heart conditions, head, back or neck ailments (or prior
surgeries to these areas of the body), or pregnant women, should be cautioned not
to operate such products.

DO NOT EXCEED THE WEIGHT LIMIT OF 120 lbs (54 kg). Rider weight does
not necessarily mean a person’s size is appropriate to fit or maintain
control of the Razor Trikke E2.

CHECK AND MAINTAIN SAFE CONDITIONS

Before use, check to confirm that any and all chain guards or other covers and
guards are in place and in serviceable condition. Check that the brake is functioning
properly, and that tires are in good condition. The product should be maintained
and repaired in accordance with the manufacturer’s specifications, using only the
manufacturer’s authorized replacement parts, and should not be modified from the
manufacturer’s original design and configuration.

ACCEPTABLE RIDING PRACTICES AND CONDITIONS
Always check and obey any local laws or regulations, which may affect
the locations where the Razor Trikke E2 may be used. Keep safely away
from cars and motor vehicle traffic at all times, and only use where
allowed and with caution.

Do not activate the speed control on the hand grip unless you are on the product
and in a safe, outdoor environment suitable for riding.

The normal powered top speed of this product will be approximately 10 mph (16
kmh), which can be affected by conditions such as rider weight, inclines, tire
inflation and battery charge level. Avoid excessive speeds that can be associated
with downhill rides.

Do not make sudden sharp turns or apply your body weight on the handlebars
when turning. Such actions could cause sudden “jack-knifing” or stops, which

could cause falls. Do not do “wheelies” or pull up on the handlebars when riding,
as this could cause the rider to slip off the front platforms.

Maintain a hold on the handlebars with both hands at all times. Do not touch the
brakes or motor on your product when in use or immediately after riding as these
parts can become very hot.

Ride defensively. Watch out for potential obstacles that could catch your wheel
or force you to swerve suddenly or lose control. Be careful to avoid pedestrians,
skaters, skateboards, scooters, bikes, children or animals who may enter your path,
and respect the rights and property of others.

The Razor Trikke E2 is intended for use on flat, dry surfaces, such as pavement or
level ground, without loose debris, such as sand, leaves, rocks or gravel. Wet, slick,
bumpy, uneven or rough surfaces may impair traction and contribute to possible
accidents. Do not ride in mud, ice, puddles or water. Watch out for potential
obstacles that could catch your wheels or force you to swerve suddenly or lose
control. Avoid sharp bumps, drainage grates, and sudden surface changes.

Do not attempt or do stunts, tricks or ride/roll backwards on your Razor Trikke E2.
It is not made to withstand abuse from misuse, such as jumping, curb grinding or
any other type of stunts. Racing, stunt riding, or other maneuvers, such as trying
to ride backwards, also enhance risk of loss of control, or may cause uncontrolled
rider actions or reactions.

• Never allow more than one person at a time to ride the Razor Trikke E2.

• Do not ride at night or when visibility is limited.

• Never use near steps or swimming pools.

• Do not allow hands, feet, hair, body parts, clothing, or similar articles to come

in contact with moving parts, wheels, or drivetrain, chain while the motor is
running.

• Never use headphones or a cell phone to talk or text when riding.

• Never hitch a ride with a vehicle.

Do not ride the Razor Trikke E2 in wet or icy weather and never immerse it in
water, as the electrical and drive components could be damaged by water or create
other possibly unsafe conditions. Never risk damaging surfaces, such as carpet or
flooring, by use indoors.

PROPER RIDING ATTIRE

Always wear proper protective equipment, such as an approved safety helmet
(with chin strap securely buckled), elbow pads and kneepads. A helmet may be
legally required by local law or regulation in your area. A long-sleeved shirt, long
pants, and gloves are recommended. Always wear athletic shoes (lace-up shoes
with rubber soles), never ride barefooted or in sandals, and keep shoelaces tied
and out of the way of the wheels, motor and drive system.

USING THE CHARGER

The charger supplied with the Razor Trikke E2 should be regularly examined for
damage to the cord, plug, enclosure and other parts. In the event of such damage,
the product must not be charged until the charger has been repaired or replaced.

• Use only with the recommended charger.

• Use caution when charging.

• The charger is not a toy. Charger should be operated by an adult.

• Do not operate charger near flammable materials.

• Unplug charger and disconnect from the product when not in use.

• Do not exceed charging time.

• Always disconnect from the charger prior to wiping down and cleaning your

product with damp cloth.

BE SURE TO READ AND UNDERSTAND THE “USAGE” SECTION OF THIS
MANUAL. FAILURE TO USE COMMON SENSE AND HEED ALL WARNINGS
AND INSTRUCTIONS INCREASES RISK OF SERIOUS INJURY. USE WITH
APPROPRIATE CAUTION AND SERIOUS ATTENTION TO SAFE OPERATION.

Safety Warnings .............................................................................................. 1

Before You Begin..............................................................................................2

Assembly and Setup .....................................................................................3-4

Charging the Battery ........................................................................................ 5

Pre-Ride Checklist/Usage ............................................................................. 6-8

Repair and Maintenance.............................................................................9-10

Trikke E2 Parts ................................................................................................11

Warranty ........................................................................................................ 14

SAFETY WARNINGS

CONTENTS

2

Need Help? Visit our website for replacement parts, product support and a list of authorized service centers
at www.razor.com or call toll free 866-467-2967 Monday - Friday 8AM - 5PM Pacific Time. Please have the
product I.D. code (located on the white label on your product or back of charger) available for better assistance.

Remove contents from box. Remove the packaging separators that protect the components from damage during shipping.
Inspect the contents of the box for scratches in the paint, dents or kinked cables that may have occurred during shipping.
Because the scooter is 50 percent assembled and packed at the factory, there should not be any problems, even if the box
has a few scars or dents.

MAKE SURE POWER SWITCH IS TURNED “OFF” BEFORE CONDUCTING ANY ASSEMBLY OR MAINTENANCE
PROCEDURES.

Estimated Assembly and Set-Up Time

Allow up to 30 minutes for assembly, not including initial charge time. Two people are recommended for assembly.
Allow up to 12 hours for initial charge (see page 5 for charging information).

BEFORE YOU BEGIN

WARNING:

DO NOT USE NON-RAZOR PARTS
WITH YOUR RAZOR ELECTRIC
SCOOTER. The scooter has been
built to certain Razor design
specifications. The original
equipment supplied at the time of
sale was selected on the basis of
its compatibility with the frame,
fork and all other parts. Certain
aftermarket parts may or may not
be compatible and may void your
warranty.

Required Tools

Note: Trikke E2 must be moving
at 3mph/5kmh while applying the
throttle to engage motor.

Product ID Locations:

See locations to the left

1. Stem

2. Battery Tray

3. Charger (not shown)

4. UPC Side of Box (not shown)

Two (2) 5mm Allen Wrenches

(Included)

Stem Handlebar

Collar
Clamp

Front Wheel

Motor

Chain Guard

Charger

Port

On/Off
Switch

2 Battery

Compartments

Brake

Throttle

Rear Wheels

Platforms

8mm and 13mm Open Wrenches

(Not Included)

3

ASSEMBLY AND SET-UP

q Attaching the Handlebars

Tools Required: 5mm Allen wrench

q Attaching the Leg Tubes

Tools Required: 5mm Allen wrench
Place battery compartments on level surface, so leg tubes are even. You may use wedge packing material or table.

2 Center the handlebars onto the

stem. Make sure the arc on the
handlebars is facing outward and
the arc of the stem is facing inward.

3 Align the holes on the handlebar

clamp with the holes on the stem
and tighten bolts until handlebars
are securely in place.

2 Attach the left leg tube to

the other side of the rotational
connector. Using a 5mm Allen
wrench, slightly tighten bolt to
hold leg tube in place.

1 Using a 5mm Allen wrench,

remove the 2 bolts on the
handlebar clamp.

1 Insert the rotational connector

(A) into the right leg tube as
shown. Using a 5mm Allen
wrench, slightly tighten bolt to
hold connector (A) in place.

4 Insert the front fork into the rotational connector.

3 Adjust the rotational connector

so the opening is positioned as
shown.

5 Insert coupling bolt as shown and tighten using two (2) 5 mm Allen

wrenches until secure.

(A)

4

ASSEMBLY AND SET-UP

q Attaching the Stem

Tools Required: 5mm Allen wrench

2 Align the front wheel with handlebars using a 5mm Allen wrench. Tighten bolts on collar clamp until collar clamp is secure.

1 Slide stem onto the front fork. Make sure throttle and brake cables are not touching the rotational corrector.

Note: Make sure the cables/wires
are out of the way before inserting
the stem in the fork.

WARNING: Failure

to properly tighten the collar
clamp may allow the handlebars
to dislodge while riding and may
cause you to lose control and fall.
When correctly tightened, the
handlebars will not rotate out of
alignment with the front wheel
under normal circumstances.

Note: The cable and wire
assembly from the handlebar
must not wrap around the stem
or handlebar. Sharp bends or
twisting of the brake cable can
cause the brakes to malfunction.